Fluoride removal studies using virgin and Ti (IV)-modified Musa paradisiaca (plantain pseudo-stem) carbons

The preparation of carbons in virgin and Ti-modified forms under controlled conditions at low temperature from plantain pseudo-stem (Musa paradisiaca) was achieved. These prepared carbons were characterized for instrumental studies such as BET, FTIR, XRD, SEM with EDS and TGA to understand the chemistry and modification. The determination of IEP and pH_ZPC established the presence of positive surface sites on the virgin (VMPC) and Ti-modified (TiMPC) carbons to facilitate the sorption of fluoride. The fluoride removal efficiency as a function of time, pH, dose, initial fluoride concentration, temperature, and co-ion intervention was studied. The maximum fluoride removal of about 81.2 and 97.7% was achievable with VMPC and TiMPC, respectively, after 20 min at the pH of 2.04 and continued for the equilibrium of 60 min. Temperature was found to be influential both by way of initial increase followed by a decrease in the fluoride uptake of MPCs. Regeneration was very consistent up to 7 cycles with the residual fluoride concentration below the WHO guide line of 1.5 mg L^?1. Highest intervention due to hydrogen carbonate ions was observed during the fluoride removal process. Kinetic (pseudo-first-order, pseudo-second-order, and intra-particle diffusion) and isotherm models (Langmuir, Freundlich, and DKR) were checked for their compliance with the present sorption system. These low temperature synthesized MPCs are found to be effective candidates in the process of fluoride abatement in water.

     

Development of waste gasification and gas reforming system for municipal solid waste (MSW)

To achieve both high-efficiency power generation and high detoxification performance, advanced-type waste power generation plants such as pyrolysis and gas reforming plants are suggested. Further surveys on actual operational data of these plants are required in terms of reliability of the system when it is introduced to waste disposal sites. To verify the technical effectiveness of advanced-type waste power generation using the pyrolysis and gas reforming method, we evaluated 10?tons/day of municipal solid wastes (MSW) treated in a demonstration plant. A demonstration test was conducted over 100?days including 35?consecutive days of operation treating MSWs. The test results show high recycling performance and harmless nature of the plant which proves it to be an excellent waste recycling system. Major test results are as follows: (1) stabilization of waste treatment is possible with the wastes of various qualities, (2) clean gas is produced from the waste whose energy recovery ratio is approximately 40?%. (3) 99.3?% weight % of dried waste are recovered as valuable materials such as clean gas, char and metal, (4) total amount of dioxin emission to the outside of the plant is very small, down to 0.0051–0.018?μg?TEQ per ton waste.     

Apportionment of TEQs from four major dioxin sources in Japan on the basis of five indicative congeners

The major sources of dioxins (polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and dioxin-like polychlorinated biphenyls (DL-PCBs)) in the environment in Japan have been considered to be combustion by-products, pentachlorophenol (PCP) formulations, chlornitrofen (CNP, 4-nitrophenyl-2,4,6-trichlorophenyl ether) formulations, and PCB products. Data on PCDDs, PCDFs and DL-PCBs from the four sources were analyzed, and indicative congeners whose concentrations were highly correlated with WHO-2006 toxic equivalencies (TEQs) were identified for each source sample. The indicative congeners for combustion by-products, PCP formulations, and CNP formulations were 2,3,4,7,8-pentachlorodibenzofuran, 1,2,3,4,6,7,8-heptachlorodibenzo-p-dioxin, and 1,2,3,7,8-pentachlorodibenzo-p-dioxin, respectively; for PCB products, the indicative congeners were IUPAC Nos. #126- and #105-pentachlorobiphenyls. Moreover, using the data on PCDDs, PCDFs and DL-PCBs, we developed a set of equations for estimating the apportionment of TEQs from the four sources by using only the concentrations of the above-mentioned five indicative congeners. The equations were used along with the analysis results of different types of environmental samples collected from Japan, to determine the TEQ contributions of the four sources. The obtained values of TEQ contributions seemed to be reasonable. The estimation method was developed by using the data on major dioxin sources in Japan, and therefore, it is generally adaptable to environmental samples from any part of Japan. The method may be usable for regions outside Japan if source identification is carried out and the estimation equations are modified appropriately.     

Hydrolysis of <Emphasis Type="Italic">Sasa senanensis</Emphasis> culm with dilute sulfuric acid for production of a fermentable substrate

To prepare a substrate for microbial conversion of xylose into xylitol, the culm of Sasa senanensis was hydrolyzed with dilute sulfuric acid. When the reaction temperature was fixed at 121°C, an optimum yield of xylose was obtained by treatment with 2% sulfuric acid for 1 h. An increase in the sulfuric acid concentration or a prolonged reaction time resulted in a decrease in the xylose yield. A fermentable substrate with a relatively high xylose concentration (36.7 g l⁻¹) was obtained by hydrolysis with 2% sulfuric acid with a liquid-to-solid ratio of 5 g g⁻¹. During hydrolysis at elevated temperatures, certain undesired byproducts were also generated, such as degradation products of solubilized sugars and lignin, which are potential inhibitors of microbial metabolism. These compounds were, however, successfully removed from the hydrolysate by treatment with activated char.     

Combined biological and photocatalytic treatment for the mineralization of phenol in water

Phenol is degraded by biological treatment, however mineralization requires long time. To decrease the time and operational cost necessary for the mineralization of phenol, an optimum operation condition of the combined biological–photocatalytical treatment was investigated. The mineralization of phenol (50 mg l⁻¹) was conducted in a flow-type biomembrane tank combined with a batch-type TiO₂-suspended photocatalytic reactor. Phenol was degraded biologically to the concentration of 6.8 mg l⁻¹, an effective concentration for further photocatalytic treatment. After the biological treatment, the biotreated phenol was treated photocatalytically to complete the mineralization of phenol. The combined treatment shortened the mineralization time compared to the biological treatment and electric cost compared to the photocatalytic treatment only. The combined treatment may be suitable for a short-time mineralization of phenol in wastewater.     

Carbonization of johkasou sludge using batch-type equipment

The carbonization of dehydrated johkasou sludge was examined using batch-type equipment. Based on the temperature changes in the carbonization room and the gas combustion room, the carbonization process was divided into three phases: phase I, drying the sludge; phase II, thermal decomposition of the dried sludge; phase III, after phase II. The times required for phases I and II were strongly correlated with the amounts of water and solid matter, respectively, in dehydrated sludge. The reduction rate of the sludge on completion of phase I was about 90% on average, and the decomposition rate of solid matter increased with time during phase II or phase II plus phase III until it reached about 50%. TOC concentration of the eluate from the carbonized sludge was used as an index to evaluate the progress of the carbonization process, and the highest temperature in the carbonization room was recognized as an important operational factor. The specific surface area and pore volume of carbonized sludge were smaller than those of charcoals and activated carbons by 1–3 orders of magnitude and 1–2 orders of magnitude, respectively. No elution of heavy metals was observed from any of the carbonized sludges examined. The reduced amount of carbon in dehydrated johkasou sludge was estimated to be about 25% of the decomposed organic matter.     

Production and characterization of KOH-activated carbon derived from polychlorinated biphenyl residue generated by the sodium dispersion process

Polychlorinated biphenyl (PCB) residues from the sodium dispersion (SD) process were employed as the raw materials for the production of activated carbon using KOH activation. The pore properties, such as the specific surface area and pore size distribution, were characterized using the Barrett–Joyner–Halenda method and the Horvath–Kawazoe method based on the N₂ adsorption isotherm at 77 K. The activated carbon produced showed similar adsorption capacities and specific surface areas to the commercially available product. The effects of the activation conditions on the porosity of the activated carbon produced were studied. The most significant factor affecting the specific surface proved to be the activation temperature. The activated carbon produced from PCB residues from the high-temperature (423–443 K) SD process had a binary pore size distribution well developed in the 4 nm region and in the micropore region. The pore structure of the carbon produced from PCB residues from the low-temperature (333–393 K) SD process had a wide range of micropores and mesopores.     

Safety equipment for passengers on railway platforms

In Japan, especially in the Tokyo area, railway platforms are increasingly crowded with passengers during commuter rush hours for many reasons. It is a very important task for railway companies to reduce the risk of passengers being exposed to accidents. We built safety fences with automatic doors on the platform of Meguro Station, one of the stations of the Yamanote commuter line in Tokyo, in order to investigate whether safety fences are useful for preventing passengers from falling off the crowded platforms onto the tracks and being hit by moving trains during commuter rush hours. As a result of our investigations, we found that the safety fences with automatic doors do not hinder the flow of the passengers, and therefore concluded that fences are a useful way of reducing the risk of accidents to passengers.     

Environmental status and management in Chiba Prefecture

Chiba Prefecture is located in the east of Tokyo Metropolis. A large scale development of industrial and residential areas began in the late 1950s until then the main industries of the prefecture were agriculture and fisheries. During the past 30 years rapid industrialization and urbanization took place resulting in occurrence of various environmental problems.In an attempt to establish a better environment condition towards 21st century Chiba Prefecture has made Environmental Plan which all the municipal governments, enterprises and inhabitants should observe to realize better environment.