Assessment of soil and soil-gas radon activity using active and passive detecting methods in Korea

Radon ((222)Rn) is a carcinogenic gas produced by the radioactive decay of radium ((226)Ra). It has been reported that soil and soil-gas are primary factors that could cause indoor radon problems. Six sites were selected for this study--Sanbook, Gangcheon, Jikyeong, Choojung, Geumsung and Homyoung--each was classified according to bedrock type. In order to investigate soil-gas radon activities and radon emanating power, innovated active and passive detecting methods were developed and applied under both field and laboratory conditions. Statistical analysis of results confirmed that the radon activity values measured using either active or passive methods under field or laboratory conditions could be interchangeable with each other.     

Effects of calibration on L-THIA GIS runoff and pollutant estimation

Urbanization can result in alteration of a watershed's hydrologic response and water quality. To simulate hydrologic and water quality impacts of land use changes, the Long-Term Hydrologic Impact Assessment (L-THIA) system has been used. The L-THIA system estimates pollutant loading based on direct runoff quantity and land use based pollutant coefficients. The accurate estimation of direct runoff is important in assessing water quality impacts of land use changes. An automated program was developed to calibrate the L-THIA model using the millions of curve number (CN) combinations associated with land uses and hydrologic soil groups. L-THIA calibration for the Little Eagle Creek (LEC) watershed near Indianapolis, Indiana was performed using land use data for 1991 and daily rainfall data for six months of 1991 (January 1-June 30) to minimize errors associated with use of different temporal land use data and rainfall data. For the calibration period, the Nash-Sutcliffe coefficient was 0.60 for estimated and observed direct runoff. The calibrated CN values were used for validation of the model for the same year (July 1-December 31), and the Nash-Sutcliffe coefficient was 0.60 for estimated and observed direct runoff. The Nash-Sutcliffe coefficient was 0.52 for January 1, 1991 to December 31, 1991 using uncalibrated CN values. As shown in this study, the use of better input parameters for the L-THIA model can improve accuracy. The effects on direct runoff and pollutant estimation of the calibrated CN values in the L-THIA model were investigated for the LEC. Following calibration, the estimated average annual direct runoff for the LEC watershed increased by 34%, total nitrogen by 24%, total phosphorus by 22%, and total lead by 43%. This study demonstrates that the L-THIA model should be calibrated and validated prior to application in a particular watershed to more accurately assess the effects of land use changes on hydrology and water quality.     

Evaluation of Carbon Uptake and Emissions by Forests in Korea During the Last Thirty Years (1973–2002)

The contribution of Korean forests to carbon sequestration for anthropogenic carbon emissions was evaluated. In addition, monitoring of carbon species released from forest fires was conducted. Despite a high carbon uptake by Korean forests, a tremendous increase in fossil fuel burning resulted in a small contribution by forests to carbon removal. The removal efficiency had a 5–31% range with an average of 12% during the period 1973–2002. In 2000, the amount of carbon released from burned trees corresponded to 1.6% of carbon uptake by forests. The distribution of surface CO concentration (ppb) derived from MOPITT (Measurement of Pollution in the Troposphere) showed high CO levels over the East/Japan Sea on April 10, 2000 when the largest forest fires occurred along the east coast of Korea. Trajectory analysis and ground CO measurements also indicated that CO levels over the East/Japan Sea were influenced by forest fires. This study suggests that continuous monitoring of carbon emissions from forest fires is needed for a more reliable estimate of carbon flux in the environment.     

The Metallic Composition of Aerosols at Three Monitoring Sites in Korea During Winter 2002

In the present study, the distribution patterns of various metals were analyzed and compared using PM samples collected concurrently from three monitoring sites located in Korea (Seoul, Busan, and Jeju island) in December 2002. As these sites can represent metal pollution with different degrees of anthropogenic activities, their concentration levels were distinguished in a systematic manner in the order of Jeju, Busan, and Seoul. By comparing the present data sets with those measured previously from other locations in Korea and around the world, we attempted to diagnose the general status of elemental pollution on the Korean peninsula. Through an application of different statistical approaches, the major processes controlling elemental levels were assessed for each of the three study sites. The results indicated the importance of both crustal and anthropogenic sources in all sites with their relative roles varying significantly from each other. The results of the metal analysis data, when examined in relation to back trajectory analysis, confirmed that their concentration changes are affected quite sensitively with air mass movement patterns. The overall results of this study consistently indicated the contribution of a strong anthropogenic source area (e.g., China) to the observed metal concentration levels in the study area, but the strengths of such signals vary considerably across the Korean peninsula.     

Assessment using CFD of the wind direction on the air discharges caused by natural ventilation of a poultry house

Air inside poultry houses must be removed on a regular basis to prevent excess of heat, particles and noxious gases that can imperil animals. To cope with this issue, natural ventilation could be an effective method when assisted by accurate predictions. This study investigates air discharges caused by natural ventilation of a poultry house by means of a three-dimensional computational fluid dynamics (CFD) model. It solves the governing equations of momentum, heat and mass transport, radiative transfers and animal-generated heat. Wind directions of 0°, 36° and 56° (0° corresponds to a wind blowing perpendicular to the ridgeline) were investigated; the CFD model predictions achieved a RMSE of 1.2 °C and 0.6 g[H₂O] kg^?1 [dry air] for internal temperature and absolute humidity, respectively, when air blew with an angle of 36°. Air renewal rates (ARR) were 39.5 (±?1.9), 34.9 (±?2.2) and 33.6 (±?1.7) volumes of the building per hour, when air blew at 0°, 36° and 56°, respectively. Such ARR predictions served to know how the gases contained in air would likely spread downstream from the building in order to define regions of potentially high gas concentration that could endanger neighbouring habitable facilities.     

Properties of alkali-activated systems with stone powder sludge

This article investigates the effects of stone powder sludge on the microstructure and strength development of alkali-activated fly ash and blast furnace slag mixes. Stone powder sludge produced from a crushed aggregate factory was used to replace fly ash and granulated blast furnace slag at replacement ratios of 0%, 10%, 20%, and 30% by mass. The unit weight and compressive strength of the samples were measured, and scanning electron microscopy/energy dispersive spectroscopy and X-ray diffraction (XRD) analyses were performed. The test results indicated that the compressive strength of alkali-activated blast furnace slag mixes using stone powder sludge was higher than that of the alkali-activated blast furnace slag control mix, but the compressive strength of alkali-activated fly ash mixes decreased with increasing replacement ratio of stone powder sludge. Microscopy results indicated that for alkaliactivated blast furnace slag samples, broken surfaces were more evident than for the alkali-activated fly ash samples. For all XRD diagrams, broad and diffuse peaks were observed around 2θ = 35° (d = 2.96–3.03 Å), implying amorphous or short-ordering structure phases.     

Estimating and comparing greenhouse gas emissions with their uncertainties using different methods: A case study for an energy supply utility

Energy supply utilities release significant amounts of greenhouse gases (GHGs) into the atmosphere. It is essential to accurately estimate GHG emissions with their uncertainties, for reducing GHG emissions and mitigating climate change. GHG emissions can be calculated by an activity-based method (i.e., fuel consumption) and continuous emission measurement (CEM). In this study, GHG emissions such as CO₂, CH₄, and N₂O are estimated for a heat generation utility, which uses bituminous coal as fuel, by applying both the activity-based method and CEM. CO₂ emissions by the activity-based method are 12–19% less than that by the CEM, while N₂O and CH₄ emissions by the activity-based method are two orders of magnitude and 60% less than those by the CEM, respectively. Comparing GHG emissions (as CO₂ equivalent) from both methods, total GHG emissions by the activity-based methods are 12–27% lower than that by the CEM, as CO₂ and N₂O emissions are lower than those by the CEM. Results from uncertainty estimation show that uncertainties in the GHG emissions by the activity-based methods range from 3.4% to about 20%, from 67% to 900%, and from about 70% to about 200% for CO₂, N₂O, and CH₄, respectively, while uncertainties in the GHG emissions by the CEM range from 4% to 4.5%. For the activity-based methods, an uncertainty in the Intergovernmental Panel on Climate Change (IPCC) default net calorific value (NCV) is the major uncertainty contributor to CO₂ emissions, while an uncertainty in the IPCC default emission factor is the major uncertainty contributor to CH₄ and N₂O emissions. For the CEM, an uncertainty in volumetric flow measurement, especially for the distribution of the volumetric flow rate in a stack, is the major uncertainty contributor to all GHG emissions, while uncertainties in concentration measurements contribute a little to uncertainties in the GHG emissions.

Implications:Energy supply utilities contribute a significant portion of the global greenhouse gas (GHG) emissions. It is important to accurately estimate GHG emissions with their uncertainties for reducing GHG emissions and mitigating climate change. GHG emissions can be estimated by an activity-based method and by continuous emission measurement (CEM), yet little study has been done to calculate GHG emissions with uncertainty analysis. This study estimates GHG emissions and their uncertainties, and also identifies major uncertainty contributors for each method.     

Atmospheric bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the vicinity of an iron and steel making plant

An IRA-743 resin bulk sampler was validated to monitor long-term bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Six consecutive sampling campaigns (2008-2009) were conducted at four sites around steel complexes in Pohang, South Korea to investigate spatial and seasonal variations of PCDD/F bulk deposition. The bulk deposition within the steel complex showed the highest ∑_4-8PCDD/F (Tetra-Octa) fluxes, ranging from 204 to 608 (mean: 352) pg m⁻² d⁻¹, indicating steel complexes were major sources of PCDD/Fs. The homologue profiles were dominated with lower chlorinated PCDFs. Furthermore, the prevailing winds were confirmed to influence the spatial distribution of PCDD/F deposition. There were apparent seasonal variations of the bulk deposition at each site, and seasonal homologue patterns of PCDD/Fs were clearly observed. According to the passive air sampling, however, no significant seasonal change of ambient air concentrations of PCDD/Fs was observed. Therefore, it was concluded that the seasonal variations of deposition fluxes of PCDD/Fs probably resulted from temperature-dependent gas/particle partitioning.     

Contamination of nonylphenolic compounds in creek water, wastewater treatment plant effluents, and sediments from Lake Shihwa and vicinity, Korea: comparison with fecal pollution

Nonylphenolic compounds (NPs), coprostanol (COP), and cholestanol, major contaminants in industrial and domestic wastewaters, were analyzed in creek water, wastewater treatment plant (WWTP) effluent, and sediment samples from artificial Lake Shihwa and its vicinity, one of the most industrialized regions in Korea. We also determined mass discharge of NPs and COP, a fecal sterol, into the lake, to understand the linkage between discharge and sediment contamination. Total NP (the sum of nonylphenol, and nonylphenol mono- and di-ethoxylates) were 0.32-875 μg L⁻¹ in creeks, 0.61-87.0 μg L⁻¹ in WWTP effluents, and 29.3-230 μg g⁻¹ TOC in sediments. Concentrations of COP were 0.09-19.0 μg L⁻¹ in creeks, 0.11-44.0 μg L⁻¹ in WWTP effluents, and 2.51-438 μg g⁻¹ TOC in sediments. The spatial distributions of NPs in creeks and sediments from the inshore region were different from those of COP, suggesting that Lake Shihwa contamination patterns from industrial effluents differ from those from domestic effluents. The mass discharge from the combined outfall of the WWTPs, located in the offshore region, was 2.27 kg d⁻¹ for NPs and 1.00 kg d⁻¹ for COP, accounting for 91% and 95% of the total discharge into Lake Shihwa, respectively. The highest concentrations of NPs and COP in sediments were found in samples at sites near the submarine outfall of the WWTPs, indicating that the submarine outfall is an important point source of wastewater pollution in Lake Shihwa.