铁阳极电解脱色直接黄11染料模拟废水

研究采用铁为阳极电化学法处理直接黄11染料模拟废水脱色性能的影响进行研究。影响因素包括:电流密度、pH值、染料浓度和电解质浓度。研究结果表明,电流密度大有利于染料废水脱色,但能耗消耗大;初始溶液在中性条件下不仅取得很好的处理效果,而且脱色能耗较低;随着染料初始浓度增加脱色率和脱色能耗降低的趋势;随着电解质浓度升高染料脱色率下降的趋势,脱色能耗先减少,然后缓慢增大。在染料初始浓度50 mg/L、pH值为7.11、电流密度2.083 mA/cm2、电解质Na2SO4浓度0.01 mol/L、温度20℃、搅拌速度600 r/min、电解时间60min条件下,脱色率达到92.2%,脱色能耗1.709 kW.h/kg染料。     

城镇生活污水厂实行清洁生产途径分析

结合企业清洁生产理论,根据污水处理厂实际情况,从“节能、降耗、减排、增效”出发,详细阐述了污水厂实行清洁生产的途径。指出节约电能、新鲜水、药剂,减少污染物排放是污水处理厂清洁生产的主要出发点。并进行实例分析。     

沼液复合型杀虫剂的田间应用试验研究

通过沼液复合型杀虫剂的田间应用试验,对各种沼液复合型杀虫剂的抗病防虫性能进行了深入研究.在大田应用条件下测试了沼液复合型杀虫剂的杀虫效果.结果表明,该沼液复合型杀虫剂对蚜虫的毒杀作用均比较明显.为了推进沼液复合型杀虫剂的商业化进程,提出便于其田间应用的各种最佳配比浓度,即BP01号、BP02号、BP03号、BP04号、BP05号沼液复合型杀虫剂抗病防虫性能最佳的配比分别为9 500倍液、26000倍液、11 667倍液、22 000倍液和13 333倍液.     

Oxidation inhibition of sulfite in dual alkali FGD system

A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization （FGD） system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and 4）.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. Pilot tests showed that the consumption rate of thiosulfate agreed well with the laboratory-scale experimental results.     

Inorganic nitrogen removal of toilet wastewater with an airlift external circulation membrane bioreactor

Removal of inorganic nitrogen (inorganic-N) from toilet wastewater, using a pilot-scale airlift external circulation membrane bioreactor (AEC-MBR) was studied. The results showed that the use of AEC-MBR with limited addition of alkaline reagents and volumetric loading rates of inorganic-N of 0.19-0.40 kg inorganic-N/(m3·d) helped achieve the desired nitrification and denitrification. Furthermore, the effects of pH and dissolved oxygen (DO) on inorganic-N removal were examined. Under the condition of MLSS at 1.56-2.35 g/L, BOD5/ammonia nitrogen (NH/-N) at 1.0, pH at 7.0-7.5, and DO at 1.0-2.0 mg/L, the removal efficiencies of NH4 -N and inorganic-N were 91.5% and 70.0%, respectively, in the AEC-MBR. The cost of addition of alkaline reagent was approximately 0.5-1.5 RMB yuan/m3, and the energy consumption was approximately 0.72 kWh/m3 at the flux of 8 L/(m2·h).     

Kinetics of selective catalytic reduction of NO by NH3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH3. The kinetics of the SCR reaction in the presence of O2 was studied in this work. The results show that the observed reaction orders were 0.74-0.99, 0.01-0.13, and 0 for NO, O2 and NH3, respectively, at 350-450℃. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst. The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N2 and H2O. Gaseous O2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process. It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH3.     

An environmental impact assessment of quantum dot photovoltaics (QDPV) from raw material acquisition through use

Some emerging technologies are expected to be pivotal for solving many of the environmental challenges faced today, especially those related to energy. However, many of these technologies may incur significant environmental impacts over their life cycle, while having environmental benefits during their use. This paper presents results of a Life Cycle Assessment (LCA) of a proposed type of nanophotovoltaic, quantum dot photovoltaic (QDPV) module. The LCA is confined to the stages of raw materials acquisition, manufacturing, and use. The impacts of QDPV are compared with other types of PV modules and energy sources - both renewable and nonrenewable. To provide a comprehensive comparative assessment, QDPV modules were compared with mature as well as emerging PV types for which data are available. Comparative assessment with other types of energy sources includes coal, oil, lignite, natural gas, diesel, nuclear, wind, and hydropower.QDPV modules may have the potential to overcome two current barriers of solar technology: low efficiencies and high manufacturing costs. If higher efficiencies are realized, QDPV modules could pave the way to large scale implementation of solar energy, helping nations move toward greater energy independence. On the other hand, candidate materials as quantum dots for solar cell applications are mostly compound semiconductors such as cadmium selenide, cadmium telluride, and lead sulfide which may be toxic and for which renewable options are limited. Toxic effects of these materials may be exacerbated by their nanoscale features.The LCA was carried out using the software SimaPro, and the Ecoinvent Life Cycle Inventory (LCI) database supplemented with available literature and patent information. Our results indicate that while QDPV modules have shorter Energy PayBack Time (EPBT), lower Global Warming Potential (GWP), SO_x and NO_x emissions than other types of PV modules, they have higher heavy metal emissions, underscoring the need for investigation of emerging technologies, especially nano-based ones, from a life cycle perspective. QDPV modules are better in all impact categories assessed than carbon-based energy sources but they have longer EPBT than wind and hydropower and higher GWP.     

Ash deposition impact on the energy performance of photovoltaic generators

A little known side effect of the atmospheric air pollution is the degradation of photovoltaic (PV) cells’ performance due to the deposition of solid particles varying in composition, size and origin. In this context, an experimental-based investigation is conducted in order to compare the energy performance of two identical pairs of PV-panels; the first being clean and the second being artificially polluted with ash, i.e. a by-product of incomplete hydrocarbons’ combustion mainly originating from thermal power stations and vehicular exhausts. A series of systematic measurements of current intensity, voltage output and solar radiation are executed simultaneously for the clean and the polluted PV-panel, so that the effect of several mass depositions on the PVs’ power output, energy yield and conversion efficiency may be determined. According to the results, a considerable deterioration of the PV-panels’ performance is obtained, i.e. almost 30% energy reduction per hour or 1.5% efficiency decrease (in absolute terms) for ash accumulation on the panels’ surface reaching up to 0.4 mg/cm².     

基于STIRPAT模型的能源消费碳足迹变化及影响因素——以江苏省苏锡常地区为例

定量研究经济社会发展对地区能源消费碳足迹的影响对区域实现低碳发展具有重要意义。论文计算了江苏省苏锡常地区1991-2008年能源消费碳足迹,采用岭回归函数对STIRPAT模型进行了拟合,采用脱钩指数分析了经济发展与能源消费碳足迹之间的关系。结果表明:①1991-2008年能源消费碳足迹平均增长速度为15.30%,能源消费碳足迹分配率以煤炭为主,石油所占比例呈波动下降趋势,天然气所占比例上升较快,能源消费碳足迹产值总体呈波动下降趋势;②经济增长是能源消费碳足迹的主要影响因素,两者关系模型拟合未出现环境库兹涅茨曲线;③经济增长与能源消费碳足迹之间处于相对脱钩与复钩的波动状态,从另一侧面验证了目前两者之间不存在库兹涅茨曲线假说的结论。     

空调系统冷冻水循环水泵变频运行的变温差控制

在分析空调系统变流量运行调节的基础上,提出了变温差控制并给出了控制方案。变温差控制过程不仅具有负反馈,而且具有正反馈,能较好的适应空调负荷的变化。比较分析了变温差控制、定温差控制、定压差控制的节能性,变温差控制的节能潜力最大,是一种最佳控制方式。