聚丙烯酰胺对聚合物驱含油污水中油珠沉降分离的影响

研究发现阴离子聚丙烯酰胺(HPAM)对聚合物驱含油污水处理有正反2方面影响.聚合物能增加污水粘度,降低油珠上浮速度,而且聚合物能增加油水界面水膜强度,延缓油珠聚并时间,这是聚合物对油珠沉降分离的不利影响;同时,聚丙烯酰胺具有絮凝性,能将水中油珠连接到一起,有利于油珠聚并.当聚丙烯酰胺相对分子质量为2.72×10⁶,浓度小于800mg/L时,絮凝作用大于粘度作用,有利于油珠的沉降分离.初始油珠粒径小是聚合物驱含油污水难处理的主要原因.横向流除油器可以加速油珠聚并,缩短沉降时间,适合处理聚合物驱含油污水.     

地下渗滤处理村镇生活污水的中试

以红壤土作为填充土壤,在2cm/d的水力负荷下,进行了地下渗滤系统处理村镇生活污水的现场中试.结果表明,地下渗滤系统对COD、氨氮、总磷和总氮有着良好的去除效果,去除率分别达到84.7%、70.0%、98.0%和77.7%,出水COD、氨氮、总磷和总氮的平均浓度分别为11.7mg/L、4.0mg/L、0.04mg/L、4.7mg/L,达到建设部颁发的生活杂用水水质标准对总氮去除机理的分析表明,由硝化/反硝化实现生物脱氮是地下渗滤系统去除总氮的主要途径.在本中试系统中,反硝化效果良好但硝化效果不够理想,改善土壤环境以促进硝化作用是提高总氮去除率的关键.对土壤中氧化还原电位的测定结果表明,土壤内部的还原性质是阻碍硝化反应进行的主要原因.     

Recovery of Ni(II) from real electroplating wastewater using fixed-bed resin adsorption and subsequent electrodeposition

Resin adsorption and subsequent electrodeposition were used for nickel recovery. Treated wastewater can meet the Electroplating Pollutant Discharge Standard. The spent resin is completely regenerated by 3 BV of 4% HCl solution. 95.6% of nickel in concentrated eluent was recovered by electrodeposition. Effective recovery of high-value heavy metals from electroplating wastewater is of great significance, but recovering nickel ions from real electroplating wastewater as nickel sheet has not been reported. In this study, the pilot-scale fixed-bed resin adsorption was conducted to recover Ni(II) ions from real nickel plating wastewater, and then the concentrated Ni(II) ions in the regenerated solution were reduced to nickel sheet via electrodeposition. A commercial cation-exchange resin was selected and the optimal resin adsorption and regeneration conditions were investigated. The resin exhibited an adsorption capacity of 63 mg/g for Ni(II) ions, and the average amount of treated water was 84.6 bed volumes (BV) in the pilot-scale experiments. After the adsorption by two ion-exchange resin columns in series and one chelating resin column, the concentrations of Ni(II) in the treated wastewater were below 0.1 mg/L. After the regeneration of the spent resin using 3 BV of 4% (w/w) HCl solution, 1.5 BV of concentrated neutral nickel solution (>30 g/L) was obtained and used in the subsequent electrodeposition process. Using the aeration method, alkali and water required in resin activation process were greatly reduced to 2 BV and 3 BV, respectively. Under the optimal electrodeposition conditions, 95.6% of Ni(II) in desorption eluent could be recovered as the elemental nickel on the cathode. The total treatment cost for the resin adsorption and regeneration as well as the electrodeposition was calculated.     

Comparison of CNT-PVA membrane and commercial polymeric membranes in treatment of emulsified oily wastewater

CNT-PVA membrane was fabricated and compared with polymeric membranes. The separation performance was evaluated by homemade and cutting fluid emulsions. The three membranes show similar oil retention rates. CNT-PVA membranes have higher permeation fluxes compared with polymeric membranes. CNT-PVA membrane shows higher fouling resistance. Membrane separation is an attractive technique for removal of emulsified oily wastewater. However, polymeric membranes which dominate the current market usually suffer from severe membrane fouling. Therefore, membranes with high fouling resistance are imperative to treat emulsified oily wastewater. In this study, carbon nanotube-polyvinyl alcohol (CNT-PVA) membrane was fabricated. And its separation performance for emulsified oily wastewater was compared with two commercial polymeric membranes (PVDF membrane and PES membrane) by filtration of two homemade emulsions and one cutting fluid emulsion. The results show that these membranes have similar oil retention efficiencies for the three emulsions. Whereas, the permeation flux of CNT-PVA membrane is 1.60 to 3.09 times of PVDF membrane and 1.41 to 11.4 times of PES membrane, respectively. Moreover, after five consecutive operation circles of filtration process and back flush, CNT-PVA membrane can recover 62.3% to 72.9% of its initial pure water flux. However, the pure water flux recovery rates are only 24.1% to 35.3% for PVDF membrane and 6.0% to 26.3% for PES membrane, respectively. Therefore, CNT-PVA membrane are more resistant to oil fouling compared with the two polymeric membranes, showing superior potential in treatment of emulsified oily wastewater.     

工业废水毒性评估与致毒物质鉴别技术进展

综述了工业废水毒性的化学评估方法、生物毒性评估方法、毒性鉴定评估(TIE)程序以及效应引导的毒物鉴别分析(EDA)中污染物提取、分离、毒性测试、致毒物质识别等技术。指出,工业废水毒害风险评估方法正逐渐向化学分析与生物毒性测试相结合的关键致毒物质鉴别方法转变,便捷、高通量是致毒物质鉴别技术的发展方向,质谱技术及替代定性监测技术的发展将提供更为准确、便捷的致毒物质鉴别方法,为工业废水潜在风险防控提供依据。     

EGSB出水回流对EGSB—SBR工艺处理果汁废水的影响

采用EGSB—SBR工艺处理实际果汁废水(COD 2 608~6 500 mg/L,p H 5.0~7.0)。在EGSB反应器成功启动及驯化完成的情况下,连续运行49 d。实验结果表明:第25天起,控制EGSB回流比为3.00∶1,EGSB反应器可在无须添加Na HCO3的条件下稳定运行,从而降低了废水处理成本;第25天起,平均进水COD,BOD5,SS分别为5 968,2 130,1 020 mg/L,平均出水COD,BOD5,SS分别降至131,11,50 mg/L,平均COD,BOD5,SS去除率分别为98%,99%,95%;组合工艺对该实际果汁废水具有良好的处理效果。     

高含盐废水脱盐处理技术研究进展

综述了几种常见的高含盐废水脱盐处理技术的发展历程、工艺原理、优缺点及目前的研究进展，分析了热分离、膜分离、电渗析、离子交换、电吸附、微生物脱盐等方法的优缺点，展望了未来废水脱盐工艺的发展方向。指出：脱盐方法将根据各类水体的水质特点更加精细化；多种脱盐技术联合应用也是今后废水脱盐的发展方向。     

废水中甲基橙的电化学降解

以FTO导电玻璃作为阳极、石墨电极作为阴极电解模拟甲基橙废水,优化了工艺条件,并对甲基橙的降解机理进行了初步探究。实验结果表明,在NaCl投加量5 g/L、电压8 V、废水pH 6、初始甲基橙质量浓度6.0 mg/L的优化条件下电解30 min,废水的脱色率达91.3%,COD降低了62%。机理研究结果表明,电解产生的羟基自由基与甲基橙发生氧化还原反应,破坏了甲基橙的显色基团,使其内部某些化学键发生断裂,从而达到脱色的目的。     

UASB-SBR组合工艺处理畜禽养殖废水的研究

近年来,随着中国畜禽养殖业的快速发展,落后的养殖模式和污染防治设施,使畜禽养殖污染日趋严重,畜禽养殖污染已居农业污染源之首,已成为中国环境污染的重要因素,对环境质量乃至人体健康都会产生不良影响。文中采用UASB—SBR组合工艺处理畜禽养殖废水,通过试验探讨SBR反应器启动方法及最佳运行模式,同时研究UASB反应器的启动方法。结果表明,SBR运行的最佳模式为进水0.5 h、反应8 h、沉淀1 h、出水0.5 h、闲置14 h。经过一段时间的启动,UASB和SBR反应器均成功启动,UASB—SBR组合工艺在处理畜禽养殖废水时可获得稳定的处理效果,COD、氨氮、总磷等出水水质均达到《畜禽养殖业污染物排放标准》(GB18596-2001)要求,为畜禽养殖废水处理的工程化应用提供了参考依据。     

采油作业“三废”控制技术研究与应用

针对采油作业产生的废酸、固废、废水处理成本高、技术不成熟等问题,研发改性废酸降压增注、深部调剖技术;高比重污泥悬浮研磨后的固废处理技术;低耗水打塞、原井液+CaCl2压井、原井液处理再利用技术,减少了"三废"的产生,解决了"三废"环保处理费高等问题,消除了环保隐患,实现了清洁生产,环境效益显著。