好氧颗粒污泥膜生物反应器污泥性状研究

采用厌氧-好氧运行方式的颗粒污泥膜生物反应器（GMBR）,连续运行近120　d表现出良好的有机物去除及同步硝化反硝化能力.对GMBR中污泥粒径分布变化研究表明,GMBR中污泥浓度的增加主要是由于粒径0.18～0.45　mm的小颗粒污泥及小于0.18　mm的絮状污泥的增加造成的,粒径大于0.45　mm的颗粒污泥能够基本稳定维持其颗粒形态,反应器运行末期,GMBR中颗粒污泥（粒径大于0.18　mm的污泥）含量稳定在污泥总量的60％～65％以上.污泥表面电荷量随着污泥组成形态的变化电负性逐渐增加,80　d后稳定在-0.42～-0.80　meq·g^-1之间.污泥表面电荷的负电性增加主要是由小于0.45　mm的污泥造成的,其中小于0.18　mm的絮状污泥对其影响最大.并且,污泥粒径越大污泥表面负电荷量越少,两者具有较好的线性关系.另外,GMBR中SVI稳定在60～90 mL/g之间,并且随着污泥表面电荷负电性的增加污泥SVI值增加,两者之间具有一定的相关性.     

厌氧-好氧生物反应器填埋工艺特性研究

基于生物反应器填埋技术,研究1种填埋场地循环操作的厌氧-好氧生物反应器填埋工艺,设计了该工艺模拟装置并研究了其运行工艺特性.厌氧阶段主要通过渗滤液回灌控制反应器工艺条件,主要试验结果为,pH值,R1在 6周后可上升至6.7～7.8,R2在17周内一直低于6.8;渗滤液COD浓度,R1在13周时下降至10?617 mg/L,R2在5周后上升至60?000 mg/L后长期趋于稳定;填埋气累计产量,R1在8周达到44%,R2几乎不产气.衡量稳定化可以分别采用渗滤液pH、COD浓度及BOD₅/COD的减少率、填埋气的累计产率等指标来判断,并据此转换为好氧填埋运行.好氧阶段主要是通过强制通风来减少恶臭和水分,主要试验结果为,通风19d氨气浓度降为1.16 mg/m³,通风23d后恶臭浓度降为19;通风14d后含水率降为26%.完成此阶段的工艺指标值可依据矿化垃圾开采的最终用途确定.对主要试验数据进行了数值模拟.厌氧-好氧填埋过程的微生物演替经RISA分析,有4个优势菌群,一些兼性菌群在厌氧-好氧阶段起着重要的承前启后作用.     

模拟可见光下土壤表面石油的光化学降解研究

在模拟可见光照射下,分析了土壤中的初始含油量、土壤类型和土壤pH值对石油在土壤表面光降解过程的影响,并利用紫外-可见分光光度法(UV-Vis)、气相色谱-氢火焰离子化检测器(GC-FID)和傅立叶红外光谱(FTIR)等方法对石油在光降解过程中的演变规律进行研究.结果表明,石油在土壤表面上的光化学降解行为符合准一级反应动力学,实验测得石油的光解速率常数为0.002 6～0.017 2 h^-1,半衰期为40～267 h.GC-FID分析结果表明,在光降解50 h后,石油的饱和烃组分中高碳数的烷烃相对含量降低,低碳数的烷烃相对含量提高;芳香烃组分的大部分色谱峰有明显地降低或消失.红外光谱分析发现,光照60 h后土壤萃取液中可能产生了羰基类化合物,说明石油在光降解过程中逐渐发生氧化.     

城市污染河道沉积物AVS与重金属生物毒性研究

采集珠江三角洲典型城市污染河道佛山水道表层沉积物和上覆水样品,测定了沉积物AVS,Eh,SEM_Pb,SEM_Cd,SEM_Cu,SEM_Zn,SEM_Ni,SEM_Cr,及上覆水Eh,DO.同步进行了底栖动物调查,结合调查结果分析了城市污染河道沉积物AVS与重金属生物毒性的关系.主要研究SEM-AVS判据在判断城市重污染河道重金属生物有效性方面的作用.所测AVS最大值为69.579 μmol/g,最小值为0.339 μmol/g,均值为20.283 μmol/g;各采样站位∑SEM₅（SEM_Pb,SEM_Cd,SEM_Cu,SEM_Zn,SEM_Ni之和）最大值为23.067 μmol/g,最小值为1.062 μmol/g;底栖动物种类和数量均较少,且基本为耐污种,优势种为水丝蚓.13个采样站位中,∑SEM₅-AVS<0的有9个,MDS分析结果显示：这9个站位中的7个底栖动物群落结构相似程度高.这表明重污染河道沉积物重金属的生物毒性与SEM-AVS的值关系密切,SEM-AVS判据在判断重污染区域重金属的生物毒性方面具有较大作用;同时说明重污染河流重金属生物毒性比较复杂,不能完全由SEM-AVS解释.     

Inorganic nitrogen removal of toilet wastewater with an airlift external circulation membrane bioreactor

Removal of inorganic nitrogen (inorganic-N) from toilet wastewater, using a pilot-scale airlift external circulation membrane bioreactor (AEC-MBR) was studied. The results showed that the use of AEC-MBR with limited addition of alkaline reagents and volumetric loading rates of inorganic-N of 0.19-0.40 kg inorganic-N/(m3·d) helped achieve the desired nitrification and denitrification. Furthermore, the effects of pH and dissolved oxygen (DO) on inorganic-N removal were examined. Under the condition of MLSS at 1.56-2.35 g/L, BOD5/ammonia nitrogen (NH/-N) at 1.0, pH at 7.0-7.5, and DO at 1.0-2.0 mg/L, the removal efficiencies of NH4 -N and inorganic-N were 91.5% and 70.0%, respectively, in the AEC-MBR. The cost of addition of alkaline reagent was approximately 0.5-1.5 RMB yuan/m3, and the energy consumption was approximately 0.72 kWh/m3 at the flux of 8 L/(m2·h).     

Alga-lysing bioreactor and dominant bacteria strain

Alga-lysing bacteria have been paid much attention to in recent years. In this study, the alga-lysing strain P05 which was isolated from an immobilizing biosystem was immobilized by coke and elastic filler, forming two biological reactors. The removal efficiencies of algae, NH4^＋-N and organic matter using the two reactors were studied. The results showed that strain P05 was an ideal algal-lysing bacteria strain because it was easy to be immobilized by coke and elastic filler which are of cheap, low biodegradability and the simple immobilization procedure. After 7 d filming, the biological film could be formed and the reactors were used to treat the eutrophic water. These two reactors were of stability and high effect with low cost and easy operation. The optimal hydraulic retention time （HRT） of each reactor was 4 h. The algae removal rates were 80.38% and 82.1% （in term of Chl-α） of coke reactor and filler reactor, respectively. And that of NH4^＋-N were 52.3% and 52.7%. The removal rates of CODMn were 39.03% and 39.64%. The strain P05 was identified as Bacillus sp. by PCR amplification of the 16S rRNA gene, BLAST analysis, and comparison with sequences in the GenBank nucleotide database.     

Non-UV based germicidal activity of metal-doped TiO2 coating on solid surfaces

A stain-based screening method was developed to screen different catalyst coatings for their germicidal activity. A Baclight dead/live bacteria viability kit （invitrogen, molecular probes） was used for staining the cell. The screening was carried out following a standard procedure. This included loading cell suspension to solid surface and maintaining contact for 30 min, then staining with a mixture containing dyes. The stained cells were observed using an epifluorescent microscope and photographed with a CCD camera under UV. Metal-doped TiO2 coatings on AI plates were prepared and tested for non-UV germicidal activity without using UV. It was tested using model microorganisms such as Bakers Yeast （Saccharomyces cerevisiae）, Bacillus subtilis, Pseudomonas putida, and Escherichia coli. On the basis of the germicidal activity of catalyst and the degree of damage caused to the cells, the stained cells may appear green （viable）, green with red or yellow nuclei and yellow （compromised） or red （nonviable）. According to their stained color, cells were counted to calculate the percentage of dead, live, and compromised cells. Compromised cells are cells that grow very slowly after reculturing indicating a degree of reversible cell damage. Screening the germicidal activity using this staining method is accurate and efficient, and requires less time than the culture-based method. A modification to the procedure for measuring germicidal activity of rough surfaces or fibrous coatings was developed. Both TiO2 and metal-doped TiO2 （Ag, Pt, Au, Cu） possess non-UV based germicidal activity. The germicidal activity of TiO2 was found to be related with its wetting property and can be improved by UV irradiation before testing. It is not greatly affected by contact time, indicating a fast acting germicidal activity.     

Effects of nitrate concentration in interstitial water on the bioremediation of simulated oil-polluted shorelines

Nutrient addition has been proved to be an effective strategy to enhance oil biodegradation in marine shorelines.To determine the optimal range of nutrient concentrations in the bioremediation of oil-polluted beaches,nitrate was added to the simulated shoreline models in the initial concentration of 1,5 and 10 mg/L.Whenever the NO3-N concentration declined to 70% of its original value, additional nutrients were supplemented to maintain a certain range.Results showed adding nutrients increased the oil biodegradation level,the counts of petroleum degrading bacteria(PDB)and heterotrophic bacteria (HB),and the promoted efficiency varied depending on the concentration of nitrate.Oil degradation level in 5 mg/L(NO_3-N)group reached as much as 84.3% accompanied with the consistently highest counts of PDB;while in 1 mg/L group oil removal efficiency was only 35.2%,and the numbers of PDB and HB were relatively low compared to the other groups supplemented with nutrients.Although counts of HB in the 10 mg/L group were remarkable,lower counts of PDB resulted in poorer oil removal efficiency (70.5%) compared to 5 mg/L group.Furthermore,it would need more NO_3-N(0.371 mg)to degrade 1 mg diesel oil in the 10 mg/L group than in the 5 mg/L group(0.197 mg).In conclusion, Nitrate concentration in 5 mg/L is superior to 1 and 10 mg/L in the enhancement of diesel oil biodegradation in simulated shorelines.     

珠江三角洲人为氨源排放清单及特征

根据收集的珠江三角洲(珠三角)人为氨源的活动水平数据,采用合理的估算方法和排放因子,建立了该地区2006年人为氨源分类别和分城市的排放清单.结果表明:①2006年珠三角地区人为氨源NH3排放总量约为194.8kt;②农业源是珠江三角洲地区人为氨源的主要排放贡献源,其中畜禽源排放的NH3占总排放量的62.1%,其次是氮肥施用源,其贡献率为21.7%;③畜禽源中肉鸡是NH3排放最大贡献源,占畜禽源NH3排放总量的43.4%,其次是肉猪,其贡献率为32.1%;④广州是珠三角地区2006年人为氨源排放量最大的城市,其次是江门,分别占NH3总排放量的23.4%和19.1%,主要的排放源均为畜禽和氮肥施用源.     

利用紫外预处理加强氯苯的生物滴滤净化

试验采用主波长为185nm的低压汞灯为紫外光源、醚型聚氨酯海绵(PU-foam)为填料的紫外-生物滴滤塔联合装置净化氯苯废气.进气氯苯浓度为600mg·m-3、停留时间分别为92、69和46s时,联合装置的平均去除率分别达到99%、95%和80%;最大去除负荷达到59.6g·(m3·h)-1;联合装置和单独生物滴滤塔生物膜形成时间分别为20d和27d;联合装置的抗冲击能力较好,停留时间缩短至30s,联合装置去除效率可达75%以上,高于单独生物滴滤塔的去除效率(25%).对紫外-生物滴滤塔联合装置机制初步探讨表明,紫外氧化氯苯形成了水溶性较好的可生物降解的物质,降低生物滴滤塔氯苯的处理负荷,同时紫外辐照过程中产生的O3能有效地控制生物滴滤塔内微生物的过量生长,从而维持整个装置的最佳运行状态.