常见的接地故障电气火灾隐患及其防范

阐述了接地故障电气火灾的形成原理和特点,结合工厂企业配电系统的实际情况,列举了接地故障电气火灾的隐患所在,并提出了预防措施。     

电弧炉烟尘治理

某特种钢厂15t电弧炉产生的烟尘污染车间及周围环境。针对电弧炉冶炼的特点选用脉冲袋式除尘器对电弧炉产生的烟尘进行捕集除尘,设计了手动旋转分体捕集罩。使用结果表明:手动旋转分体捕集罩操作灵活方便,除尘效果达到设计要求。     

Characterization of fuel gas products from the treatment of solid waste streams with a plasma arc torch

This work addresses the plasma treatment of two solid waste streams and production of fuel gases from the process. In this study, carpet waste and simulated solid wastes generated by a United States Air Force Basic Expeditionary Airfield Resources Base deployment were used. Waste was treated in a furnace fitted with a 100kW plasma arc torch. The off gas was analyzed to determine its composition. The product gas was composed primarily of carbon monoxide and hydrogen, with small amounts of methane, benzene and toluene also detected. These experiments demonstrate the feasibility of producing fuel gases by plasma treatment of the solid waste streams. While the thermal energy value of the fuel gas produced in these experiments was less than the energy input, a higher waste-to-fuel gas conversion efficiency is expected in full-scale application.     

脉冲电弧液相放电等离子体污水消毒灭菌

采用某污水厂的出水,利用脉冲电弧液相放电等离子体技术,研究了放电脉冲次数、放电电压、放电极间距对大肠杆菌灭杀的影响。结果表明:随着放电脉冲次数的增加,灭菌率升高。当放电脉冲次数为400时,灭菌率高达99.1%。随着放电电压的升高,大肠杆菌的去除率升高,其中电压为3 kV最高,灭菌率为96.7%。在相同的电压下,放电极间距越小,灭菌效率越高,放电间距0.5 mm时最佳。利用扫描电镜观察等离子体处理前后大肠杆菌细胞的形貌变化,并根据灭菌的结果对等离子体的灭菌机理进行了分析,发现了灭菌消毒与等离子体中所含的活性粒子成分有密切的关系。     

手工电弧焊接防触电措施

从电焊机的使用中的常见问题诸如电源的连接、设备的包养、防护的措施等方面告诉人们如何去避免危险的放生。对实际的现场作业的安全防护具有现实的指导意义。     

Predictive control based double-electrode submerged arc welding for filet joints

Double-electrode submerged arc welding (DE-SAW) is an innovative process to achieve the same metal deposition rate at reduced heat input. To maximally take advantage of this new capability, the heat input needed to produce acceptable welds needs to be reduced. A joint gap is successfully introduced to reduce the required heat input but it introduces variations affecting currents/heat input. To minimize the resultant variations in currents and resultant welds, the process is modeled and a multivariable predictive control algorithm is developed to control the currents at desired levels. Experiments verified the effectiveness of the resultant feedback controlled DE-SAW process.     

Destruction of PCDD/Fs by gliding arc discharges

PCDD/Fs have been become a serious issue because of their toxicological effects and associated adverse health implications.In this study,the gliding arc plasma was tested for treatment of polychlorinated dibenzo-p-dioxins(PCDDs)and polychlorinated dibenzofurans (PCDFs),which was synthesized from pentachiorophenol in atmospheric condition at 35℃with or without the catalysis of CuCl_2. From the experiment,we found that the destruction efficiency of PCDD/F homologues after gliding was discharge ranged from 25% to 79%.This result demonstrates that gliding arc plasma is an effective technology to decompose PCDDs/Fs in flue gas.A plausible degradation mechanism for PCDD/Fs by gliding arc was discussed.Finally,a multistage reactor structure of gliding arc was proposed to upgrade removal efficiency for PCDD/Fs.     

铸造烟尘治理技术

结合铸造工艺过程,分析介绍了铸造烟尘的来源及其危害,介绍了铸造粉尘的除尘技术,重点介绍了袋式除尘新设备的特点以及国外电弧炉烟尘的治理新技术.     

电感性本质安全电路L/R的选择原则

基于电感性本质安全电路放电电流线性衰减模型,引入最小建弧电压的概念,得到了放电时间不含未知参数的表达式,利用电感电路的本质安全性能判别式,确定了电感电阻比L/R的选取原则.     

Decomposition of CCl4 and CHCl3 on gliding arc plasma

Introduction C hlorinated volatile organic com pounds(C V O C s) w ere released to the atm osphere as flue gases from various industrial processes. C hlorinated hydrocar- bons have been w idely accepted as solvents and chem ical interm ediates in the m an…