肥煤自燃全过程热动力学特征参数研究

实验测定了林西矿肥煤样品30~900℃煤自燃全过程热动力学特征参数,得出:TG/DTG曲线显示煤样DTG初始临界温度45℃,干裂温度122℃,活性温度195℃,增速温度265℃,质量极大值温度342℃,着火温度465℃,最大热失重速率温度515℃和燃尽温度690℃;DSC曲线显示,煤样初始放热温度60℃、最大热释放速率温度511℃。结合TG-DTG-DSC曲线综合分析可知,煤温达到510℃左右时煤样反应最剧烈。由煤自燃标志气体测定实验系统得出:煤温130℃后CO,CO 2释放量迅速增加,210℃增加速度下降;CH 4,C 2 H 6含量变化具有规律性且两者变化相近;C 2 H 4出现温度为130℃;C 2 H 4/C 2 H 6比值在190~350℃有较强的规律性,呈上升趋势且上升速度较快;350℃之后,CH 4,C 2 H 6,C 2 H 4体积分数均开始急剧增大;C 2 H 4/CO与C 2 H 4/CO 2变化趋势大致相同,在130~350℃时缓慢增长,达到350℃后比值呈指数形式上升。经拟合曲线,得到活化能的3个突变点温度:70,180,220℃,其中180℃与交叉点温度相吻合。通过以上研究,得到了肥煤自燃全过程的热力学特征参数,为实际生产中防治煤自燃提供了理论依据。     

不同自燃倾向性煤的指标气体产生规律实验研究

为研究不同自燃倾向性煤的自燃指标气体变化规律，提高对煤早期自燃预测预报的准确度，采用程序升温实验系统，得到内蒙古褐煤、神东长焰煤、河南气煤及枣庄焦煤4种不同变质程度煤的氧化时间随温度的变化关系，以及指标气体浓度在煤氧化过程中的变化规律。结果表明:自燃倾向性最高的褐煤应以CO和乙烯作为煤自燃早期预报的首选指标气体；易自燃的长焰煤应采用乙烯和烯烷比为主、以CO为辅的煤自燃判定指标；自燃倾向性较低的气煤应以乙烯和烯烷比作为煤自燃预报指标；CO是自燃倾向性最低的焦煤的最佳自燃预报指标气体。     

氢安全研究现状及面临的挑战

氢能具有储运便捷、来源多样、洁净环保等突出优点,许多国家把发展氢能作为重要的能源战略。氢安全是氢能大规模商业化应用的重要保障。在分析国内外氢安全领域近年来最新研究进展的基础上,依次从氢泄漏与扩散、氢燃烧与爆炸、氢与金属材料相容性及氢风险评价等方面,系统总结了国内外氢安全研究面临的挑战,并对我国氢安全的发展提出了建议。     

Characterization of coffee residues pellets and their performance in a residential combustor

Spent coffee grounds (SCG) and coffee husks (CH) were evaluated as biofuels, after densification, for energy production. CH represent a specific problem for the coffee industry due to a low calorific value, high ash content, and a very low bulk density. Hence, the energetic potential of SCG (95 wt%)/CH (5 wt%) blend and pure SCG (100%) were examined. The blend of SCG and CH was limited to 5 wt% of CH because of the low bulk density of CH. Therefore, physicochemical and energetic characterizations of the produced pellets were performed. Thermogravimetric analyses were performed under nitrogen and air atmospheres to evaluate the CH behavior in the blend. Characterization study shows that both produced pellets could reach the French Agropellets standard (AQI). Thermal degradation showed that the mean reactivity of the SCG/HC pellets was higher than pure SCG. Then, combustion experiments were performed in a domestic combustor, after modification of the boiler power in order to improve its energetic performances. The presence of CH led to a rise of CO, NOx, VOC’s, and particle emissions. Nevertheless, the performances of the biofuels are almost in agreement the NF EN 12809 standard.     

Fuel efficiency improvement of a dual-fuel engine fuelled with Honge oil methyl ester (HOME)–bioethanol and producer gas

Renewable and alternative fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues (Yaliwal et al. 2013. International Journal of Sustainable Engineering, doi:10.1080/19397038.2013.801530. Zhu et al. 2011a, Applied Thermal Engineering 31 (14–15): 2271–2278; Zhu et al. 2011b, Fuel 90: 1743-1750; Banapurmath, Tewari, and Hosmath 2008, Renewable Energy 33: 2007-2018; Banapurmath 2009, “Performance, Combustion and Emission Characteristics of a Single Cylinder Direct Injection CI Engine Operated on Dual Fuel Mode Using Honge Oil and Producer Gas.” PhD thesis, 1–195; Banapurmath et al. 2011, Waste and Biomass Valorization 2: 1–11). In this context, the main objective of the present work is to study methods of biofuel production such as Honge oil methyl ester (HOME) using a conventional transesterification process and bioethanol from the Calliandra calothyrsus shrub using a new pretreatment method known as hydrothermal explosion. Further, experimental investigations were carried out on a single-cylinder, four-stroke, direct-injection stationary diesel engine operating in a dual-fuel mode using HOME, bioethanol and producer gas combinations to determine its performance, combustion and emission characteristics. The performance of the dual-fuel engine was analyzed at optimized engine conditions. HOME-Bioethanol (BE) blends such as HOME+ 5% bioethanol (BE5), HOME+ 10% bioethanol (BE10) and HOME+ 15% bioethanol (BE15) were prepared by adding bioethanol to HOME (on volume basis) in different proportions ranging from 5 to 15% with an increment of 5%. In this present work, the effect of different BE blends on the performance of producer gas fuelled dual fuel engine was studied. Experimental investigation on dual fuel engine using BE5-Producer gas operation resulted in up to 4–9% increased brake thermal efficiency with decreased hydrocarbon (HC), carbon monoxide (CO) and marginally increased nitric oxide (NOx) emission levels compared to HOME-Producer gas, BE10-producer gas and BE15-producer gas mode of operation. However, it was observed that, the overall performance of BE-producer gas operation was found to be lower compared to diesel-producer gas operation.     

沈阳市固定燃烧源挥发性有机化合物2007年排放清单研究

挥发性有机化合物(VOCs)与.OH的反应是对流层臭氧形成的重要化学过程,是导致城市光化学烟雾的根本原因。为建立沈阳市固定燃烧源VOCs排放清单,选取了电力热力行业、钢铁行业和秸秆燃烧3个主要排放源进行研究。结果表明:(1)2007年,沈阳市固定燃烧源VOCs排放总量为8 544.539 t,其中排放量最大的是秸秆燃烧,为6 317.115 t;其次是电力热力行业,为2 225.780 t;最小的是钢铁行业,为1.644 t。(2)沈阳市各区县固定燃烧源VOCs排放量由大到小排序依次为新民市、法库县、东陵区、康平县、辽中县、于洪区、苏家屯区、大东区、沈北新区、铁西区、沈河区、皇姑区、和平区;VOCs排放强度由大到小排序依次为大东区、沈河区、铁西区、东陵区、皇姑区、和平区、于洪区、苏家屯区、法库县、康平县、辽中县、沈北新区、新民市。     

好氧颗粒污泥自生动态膜生物反应器处理碱减量印染废水

自生动态膜生物反应器(SFDMBR)接种颗粒污泥启动,研究溶解氧浓度和水力停留时间对该反应器处理碱减量印染废水的影响。自生动态膜生物反应器形成稳定的动态膜后,出水浊度小于10 NTU,系统对浊度的去除率在90%以上,溶解氧和水力停留时间对反应器出水浊度基本无影响。系统对废水色度的去除率随着溶解氧浓度的提高和水力停留时间的延长而增加,但是系统对色度的去除效率一般不超过40%。溶解氧浓度由0.3 mg/L逐渐增大至2.4 mg/L,COD的去除率由40%提升至80%,而当溶解氧浓度大于1.0 mg/L后,UV254的去除率达到95%。水力停留时间在8~48 h时,COD去除效率由65%逐渐上升至85%左右;水力停留时间在8~32 h,UV254去除效率为68%~93%,超过32 h后水力停留时间对UV254去除效率的影响已不明显。     

层燃螺旋炉排焚烧技术处理含油污泥研究

通过对几种含油污泥无害化处理技术的比选,分析不同处理技术物耗、能耗情况,优选出经济有效的含油污泥焚烧技术,结合新疆油田含油污泥的特点,采用层燃螺旋炉排焚烧技术,利用其燃烧热能生产蒸汽用于原油生产,采用余热吸收急冷与碱液半干法除酸技术,有效控制了二次污染;采用布袋除尘与烟尘固化技术确保了烟气达标排放。年节省成本支出3095.88万元。     

循环流化床锅炉掺烧高炉煤气的应用

介绍了高炉煤气的主要燃烧特性，分析了高炉煤气在循环流化床锅炉中掺烧时对炉膛换热、过热蒸汽温度、锅炉负荷、热效率、分离装置以及环境的影响，并提出了消除不良影响的相应措施。     

Chemical composition and properties of ashes from combustion plants using Miscanthus as fuel

Miscanthus giganteus is one of the energy crops considered to show potential for a substantial contribution to sustainable energy production. In the literature there is little data available about the chemical composition of ashes from the combustion of Miscanthus and practically no data about their physical properties. However, for handling, treatment and utilization of the ashes this information is important. In this study ashes from two biomass combustion plants using Miscanthus as fuel were investigated. The density of the ashes was 2230 ± 35 kg/m~3, which was similar to the density of ashes from straw combustion. Also the bulk densities were close to those reported for straw ashes. The flowability of the ashes was a little worse than the flowability of ashes from wood combustion. The measured heavy metal concentrations were below the usual limits for utilization of the ashes as soil conditioner. The concentrations in the bottom ash were similar to those reported for ash from forest residue combustion plants. In comparison with cyclone fly ashes from forest residue combustion the measured heavy metal concentrations in the cyclone fly ash were considerably lower. Cl-, S and Zn were enriched in the cyclone fly ash which is also known for ashes from wood combustion. In comparison with literature data obtained from Miscanthus plant material the concentrations of K, Cl-and S were lower.This can be attributed to the fact that the finest fly ash is not collected by the cyclone de-dusting system of the Miscanthus combustion plants.