A case study of promoting CH4 discharge and preventing coal & gas outburst accidents by using cross-layer liquid injection technology

To solve the problem of gas extraction in coal bodies with the outburst risk, the cross-layer drilling fluid injection technology for protecting rock pillars is adopted to promote gas extraction. We combined theoretical calculations, laboratory experiments, and field tests to analyze the degree of fissure development in different parts of the coal body. We also determined the liquid injection parameters and negative extraction pressures. The CH₄ extraction effects of three stages before, during, and after liquid injection was compared. The results show that the possibility of coal outbursts in different parts is reduced by 58%∼70% by using liquid injection and pumping technology. The peak value of CH₄ pure flow in the main pipe is increased by 1.5–2.8 times, and the average value is increased by 1.8–2.6 times. The peak value of gas concentration at the orifice of the extraction hole is increased by 1.6–3.5 times, and the average value is increased by 1.6–4 times. Liquid injection to promote extraction greatly improves the gas extraction efficiency in coal bodies, which is of great significance to reducing cost, shortening the construction period, and ensuring safe production, and providing a reference for similar engineering construction.     

水力压裂有效压裂半径的影响因素研究*

为改善水力压裂增透效果,提高煤层瓦斯抽采效率,减少矿井瓦斯灾害,明确不同因素对水力压裂有效压裂半径的影响,基于Mohr-Coulomb准则建立水力压裂渗流—损伤耦合方程,并且求得水力压裂破裂区半径运算公式;运用ABAQUS软件模拟并分析地应力σ、注水水压P、压裂孔径d及弹性模量E对水力压裂有效压裂半径L的影响;并通过灰色关联分析方法确定水力压裂有效压裂半径的主控因素。研究结果表明:水力压裂有效压裂半径与注水水压、压裂孔径及弹性模量呈递增关系,与煤层地应力呈递减关系;水力压裂有效压裂半径受煤层地应力的影响最大,注水水压次之,受压裂孔径和弹性模量的影响相对较弱。     

矿用润湿型压裂液的制备与性能分析*

为有效减少煤矿开采时粉尘的生成量,降低综采区粉尘含量。基于自由基聚合和季铵化反应制备1种润湿型压裂液。通过单因素实验,确定最优配比是200 mL水,5 g油酸,0.3 g过硫酸钾,3 g N,N′-亚甲基双丙烯酰胺,2 mL环氧氯丙烷,2 g氯化钾和2 g水杨酸钠。对压裂液的反应过程、微观结构、剪切黏度、剪切稳定性、滤失性、润湿型性和清洁性进行研究。研究结果表明:该压裂液具有较高的剪切黏度和较佳的剪切稳定性,有利于注入煤层;具有较低的滤失性,便于压裂造缝;具有良好的润湿能力,能够有效地渗透到煤层中去;具有残渣含量少等特点,清洁性良好。     

A low pressure direct gas injection system for a four stroke LPG: Diesel dual fuel engine

Internal combustion engines running on gaseous fuels produce low torque because the inducted gaseous fuel displaces air and reduces the volumetric efficiency. This can be overcome by injecting the gaseous fuel directly into the cylinder after the intake of air is completed. This work is a step in developing and demonstrating a cost effective system, as such systems are not readily available for small applications. A low-pressure gas injector was mounted on the cylinder barrel of a fully instrumented dual fuel engine. Its location is such that the injector will be exposed to the cylinder gases about 65.5 degrees before bottom dead center, where the cylinder pressure and temperature will be relatively low. An electronic controller was also developed to time the injection process to occur after the intake valve closes and also to control the duration of injection (quantity). Experiments were conducted with LPG (Liquefied petroleum gas) as the primary fuel that was injected with this new system and diesel as the pilot fuel at the rated speed of 1500 rpm with different amounts of LPG at 80% and 100% load. Comparisons of performance, combustion and emissions with the conventional manifold injection of LPG were done. The system allowed greater amounts of LPG to be used without knock as compared to manifold injection. On the whole the developed system has potential for application in small dual fuel and spark ignited gas engines and can be taken up for further optimization.     

没食子酸—H_2O_2—甲醛—Co(Ⅱ)化学发光体系测定钴

本文用没食子酸—H_2O_2—甲醛—CO(Ⅱ)化学发光体系建立了痕量钴的化学发光测定法.方法检出限达0.5ng/ml 钴,线性范围是1×10~(-9)—8×10~(-7)g/ml 钴,测定的相对标准偏差小于1.0%,考察了24种常见离子的干扰情况.方法已用于水样中痕量钴的测定.     

火电厂炉内喷钙法烟气脱硫改造实践

采用石灰石-石膏湿法脱硫工艺对1×350 MW燃煤电厂原有炉内喷钙尾部增湿脱硫工艺进行改造,改造后运行表明:脱硫效率!95%,确保在常用煤种情况下二氧化硫排放浓度≤100 mg/m3,同时年运行费用相对改造前直接降低数百万元,实现了环境效益和经济效益的双赢。     

顺序注射阻抑动力学光度法测定环境水样中的对苯二酚

在酸性条件下,利用对苯二酚能够阻抑碱性藏花红和溴酸钾反应的原理,联用顺序注射分析技术建立了快速测定环境水样中对苯二酚的新方法。在最佳实验条件下,对苯二酚的线性范围为0.05~1.50μg·m L~(-1),检出限为0.02μg·m L~(-1),完成一次分析循环总的试剂消耗仅为0.125 m L。该方法用于自来水、地表水和河水中对苯二酚的测定,结果与HPLC法所得结果对照,无显著性差异。     

压裂钻孔孔壁破坏行为与注水流量相关性试验研究

为分析流量对水力压裂钻孔起裂特征的影响,开展了不同注水流量水力压裂实验,得到了煤体起裂过程的孔壁压缩应变-水压曲线。结果表明,流量的增大使破裂形态趋于复杂,表现在裂缝的数目及宽度会变多增大,而原煤则更易于沟通原生裂隙;对于无明显节理的配比型煤,随着注水流量增大,孔壁应变速率和起裂压力均增高;对于含明显节理的原煤,孔壁应变速率及起裂压力变化具有一致性,但与流量变化不一致,原煤内部的节理会影响试块起裂行为,降低钻孔内能量积聚速率和煤体破裂强度。研究成果对于揭示钻孔起裂行为具有重要理论意义,为水力压裂实验研究提供了一种新思路。     

高炉煤粉喷吹站消防水系统设计

介绍了钢铁行业的高炉煤粉喷吹站消防水系统总的设计原则、设计方法,并针对某钢铁联合企业两座1 780 m3高炉合建的煤粉喷吹站消防水系统设计的工程实例,详细论述了高炉煤粉喷吹站消防水系统的选择方法、组成部分、主要参数的确定方法及控制方法。同时结合工程实践,对高炉煤粉喷吹站消防水系统设计中常遇到的一些问题提出了合理建议。     

煤粉燃烧性与工业分析、着火温度的相关性研究

喷吹煤粉燃烧性是生产中的一个重要参数,实时掌握原煤燃烧性的波动变化对保证喷煤的安全和稳定十分必要。直接测量煤粉燃烧性的方法成本高,时间长,操作复杂,不利于生产应用;采用测定煤的工业分析和着火温度的方法简单易行,应用范围广泛。该文针对某炼铁厂的15种原煤,进行了工业分析和着火温度的实验研究,引入了统计学中相关系数的概念对数据进行了处理分析,实验证明煤的挥发分和着火温度与煤粉的燃烧性高度线性相关,此方法为利用两参数间接分析煤粉燃烧性提供了理论基础。