膜电解法在线再生酸性蚀刻液及回收铜新技术

采用极化曲线法研究了酸性蚀刻液阴、阳极电化学行为，并构建了离子膜电解反应体系，考察了在线再生酸性蚀刻液及回收铜的效果。结果表明，阳极氧化过程发生浓差极化，存在极限电流密度，Cu＋含量越高，极限电流密度越大；阴极还原分4步反应进行，存在极限电流密度；强化溶液传质可有效提高阴、阳极极限电流密度，有利于避免电解过程中析出氯气和氢气；在线实验表明，通过监控阳极液ORP，可避免析出氯气；分步降低电流电解有利于避免析出氢气，形成致密的金属铜块；在电流为9～24A范围内分4步电解23．5h可再生酸性蚀刻液23．5L，同时电沉积回收510g铜，纯度高达99．98％。阴极电流效率达到95．2％，吨铜电耗3251kWh。电解过程中无氯气和氢气析出，无废液排放，表明膜电解法在线再生酸性蚀刻液具有良好的应用前景。     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.     

废弃印刷线路板碘化法浸金研究

针对碘化法从废弃印刷线路板中提取金的工艺设计，分别考察了碘的质量分数、n(I₂)/n(I^-)比值、固液比、双氧水的质量分数、pH值、浸出时间和浸出温度对金浸出率的影响。结合正交设计优化实验方法,提出了从废弃印刷线路板中碘化法浸取金的最佳工艺条件：碘的质量分数为1.1％，n(I₂)∶n(I^-)=1∶10，双氧水的质量分数为1.5％，浸出时间4 h，固液比为1∶10，浸出温度为常温（25℃），溶液pH值为中性，此时金浸出率可达97.5％。     

液-固流化床回收印刷线路板中金属的研究

根据废弃印刷线路板中材料密度不同，采用水介质流化床对印刷线路板粉末中的金属进行回收，对0.25～0.177、0.177～0.104、0.104～0.074和-0.074 mm 4个粒级范围内的物料进行分选试验。试验结果表明，在上述4个粒级范围内，随介质流速的增大，金属回收率降低；金属回收率η与实际操作速度（ua）和颗粒终端沉降速度（ut）的比值φ（ua/ut）存在一定线性关系，分析模拟了η与φ之间的相关性方程，外推试验的结果证明了相关性方程的可靠性；在合适的操作条件下，各粒级范围内金属的回收率分别为95.02%、90.07%、87.5%和92.68%。     

Recycling of organic materials and solder from waste printed circuit boards by vacuum pyrolysis-centrifugation coupling technology

Here, we focused on the recycling of waste printed circuit boards (WPCBs) using vacuum pyrolysis-centrifugation coupling technology (VPCT) aiming to obtain valuable feedstock and resolve environmental pollution. The two types of WPCBs were pyrolysed at 600°C for 30 min under vacuum condition. During the pyrolysis process, the solder of WPCBs was separated and recovered when the temperature range was 400-600°C, and the rotating drum was rotated at 1000 rpm for 10 min. The type-A of WPCBs pyrolysed to form an average of 67.91 wt.% residue, 27.84 wt.% oil, and 4.25 wt.% gas; and pyrolysis of the type-B of WPCBs led to an average mass balance of 72.22 wt.% residue, 21.57 wt.% oil, and 6.21 wt.% gas. The GC-MS and FT-IR analyses showed that the two pyrolysis oils consisted mainly of phenols and substituted phenols. The pyrolysis oil can be used for fuel or chemical feedstock for further processing. The recovered solder can be recycled directly and it can also be a good resource of lead and tin for refining. The pyrolysis residues contained various metals, glass fibers and other inorganic materials, which could be recovered after further treatment. The pyrolysis gases consisted mainly of CO, CO(2), CH(4), and H(2), which could be collected and recycled.     

核电燃料元件厂环境辐射监测与评价

本文对 1994～ 1998年核电燃料元件生产所排放的放射性流出物及环境辐射进行了监测分析。结果表明 ,在正常生产运行情况下 ,放射性流出物对周围公众造成的年最大个人有效剂量当量是 7 2 6× 10 -2 mSv ,远低于公众剂量限值。评价半径为80km范围内的集体有效剂量当量为 4 70× 10 -2 人·Sv/a。     

Influences of Magnesium <Emphasis Type="Italic">tri-</Emphasis>Silicate on the Physical,Mechanical, and Degradable Properties of Ultraviolet (UV) Radiation Cured Plain Board Surface

A series of formulations were prepared with different percentages of oligomer, epoxy diacrylate (EA-1020 ), monomer, 1,6 Hexane diol diacrylate,(HDDA) and different percentages of filler (Magnesium tri-silicate, Mg₂Si₃O₈). Irgacure 369 [2-Benzyl-2-dimethyl-amine-1 (4-morpholinophenyl) butanone-1] was used in the formulations as photoinitiator. Ultraviolet (UV) cured thin polymer films were prepared from these formulating solutions on clean glass plates. Pendulum hardness (PH), gel content and macro scratch hardness (MSH) of the UV cured films were studied. One percent Mg₂Si₃O₈ containing formulation showed the premium properties. The substrates (plain board) were coated by these formulating solutions and cured under the same UV lamp at different intensities of radiation. Various properties of the coated surface such as PH, gloss, adhesion, abrasion and MSH were investigated. The base coat containing 1% Mg₂Si₃O₈ and top coat containing 48% HDDA produced the best performance among all the formulations inspected. The degradable properties in different weathering conditions on PH, gloss, adhesion, abrasion and MSH were measured. The surface cured with the optimized formulation (E) again yielded the minimum loss of the properties.     

青藏铁路列车运行控制系统的安全性分析

分析了青藏铁路中多种不利因素对轨道电路参数的影响 ;提出了在青藏铁路不宜采用现行基于轨道电路的列车运行控制系统 ,而应选择基于通信的列车运行控制系统的理由 ;给出了系统的基本结构及提高系统可靠性的措施 ;与此同时 ,就人们关心的无线传输列车控制数据的可靠性和安全性难题 ,通过建立马尔可夫模型的方法进行了分析     

不同塔型交流输电线路的电磁环境分析

选择500 kV同杆双回紧凑型线路、500 kV同杆双回常规线路、500 kV单回紧凑型线路、500 kV单回常规线路、220 kV同杆双回线路和220 kV/110 kV同杆4回线路进行不同塔型交流线路的电磁环境测量.通过测试和计算分析,给出了被测试线路的电磁环境水平.     

Manufacture of strand board made from construction scrap wood

The objective of this research was to evaluate the physical and mechanical properties of strand board made from construction scrap wood. The strand board was manufactured using Sugi (Cryptomeria japonica D. Don) and Douglas-fir (Pseudotsuga japonica) strands selected from construction scrap wood. The strands were oriented, and three-layer (face/core/face) strand board of three types was produced: one in which the strands of the face layer were oriented at a right angle to those of the core layer (R board), another in which the strands of the face layer were oriented parallel to those of the core layer (P board), and a third in which the strands of both layers were oriented at random (Ra board). The physical and mechanical properties of the boards were evaluated based on Japanese Industrial Standard (JIS). The main results obtained are as follows: the bending strength of the strand board with a density larger than 0.55 g/cm³ exceeded the standard value of type 18 particleboard of JIS A 5908. The bending strength of the strand board was affected by board density, strand orientation and resin content, and became larger with increased density as well as resin content. That of the parallel specimen of P board was the largest among the specimen-orientations and types. The internal bond strength of the strand board with a density larger than 0.55 g/cm³ exceeded the standard value of type 18 particleboard and type 24-10 particleboard of JIS A 5908. The internal bond strength was markedly affected by the resin content of the core layer, and became larger with increased density. The thickness swelling of the strand board decreased with increased resin content, and become larger with increased density.