Elimination of Methanol and Ethanol by Biofiltration: An Experimental Study

This study presents the experimental results obtained during long-term operation of two biofilters treating two alcohols: methanol and ethanol. The biofilters used for this purpose were previously packed with a compost material made from tobacco processing residues. The alcohols concentrations tested lay between 0.40 and 3.20 g/m³ for methanol, and 0.55 and 5.05 g/m³ for ethanol. The empty bed residence time in each biofilter was 60 s. Biofilter inlet loads of less than 190 and 300 g/m³/h for the methanol and ethanol additions respectively, were thereafter evaluated. In addition, the concentrations of nutrient nitrogen were also varied, from 0.1 to 2.0 g-N/l and from 0.3 to 11.3 g-N/l for the ethanol and the methanol, respectively. The results thus obtained have made it possible to select the optimal nitrogen concentrations which, for the cases examined, turn out to be 0.3 g-N/l and between 2 and 3.8 g-N/l for the ethanol and methanol substrates, respectively. The maximum elimination capacities obtained in this study were 82 and 150 g/m³/h, respectively for the methanol and ethanol cases. It was therefore concluded that, for a readily biodegradable compound such as ethanol, the nitrogen requirement is substantially lower than that needed for the methanol degradation, the latter appearing to be more difficult to degrade biologically under similar operating conditions. The production rate of the co-product carbon dioxide during methanol and ethanol biofiltration was also investigated. Also, a good correlation was found to exist between the temperature and the conversion achieved in the biofilter.     

有效磷含量对硝酸铵溶液热安全性的影响

为了了解硝酸磷肥生产过程中,硝酸铵溶液中加入磷酸一铵的安全性,通过自制实验装置,研究了有效磷含量对质量分数为85%的硝酸铵溶液热分解的影响。结果表明,质量分数为85%的硝酸铵和磷酸一铵混合溶液的临界爆炸温度高于纯质量分数为85%的硝酸铵溶液,稳定性更好;磷酸一铵抑制硝酸铵的热分解,随着有效磷含量的增加,硝酸铵混合溶液临界爆炸温度升高;升温速率对硝酸铵混合溶液的临界爆炸温度影响很大,随着升温速率由2℃/min升高到3℃/min,质量分数为85%的硝酸铵混合溶液的临界爆炸温度升高,不易发生爆炸,安全性更好。研究结果对硝酸磷肥的生产安全有一定的指导意义。     

活性炭纤维对于离子的电吸附选择性能研究

通过循环伏安测试、交流阻抗测试、电吸附实验等方法研究了单组分和多组分溶液中不同离子在活性炭纤维电极表面的选择性电吸附性能。结果表明,电吸附选择性能与离子的水合半径、离子价态、离子浓度有关;增大初始浓度可以提高电吸附容量;并且,由于强烈的选择吸附作用,Ca2+离子可以吸附取代其它已经被吸附的离子。     

NaOH溶液吸收CO2的试验研究

为了满足国际海事组织对船舶CO2排放的要求,建立了一种针对船舶尾气CO2的循环吸收系统,利用NaOH溶液吸收CO2.NaOH溶液完成第一步吸收反应后在第二步反应中被还原,从而可以循环利用.分析了初始反应温度、NaOH浓度及溶液中的Na2CO3对CO2吸收率的影响,并计算了循环反应中NaOH的再生率和CaO的过量系数.结果表明,CaO过量系数为1.2时对CO2固化效果最佳,此时NaOH溶液再生率达79.31％.研究表明,NaOH溶液吸收船舶尾气中CO2的循环系统效率高、成本低.     

基于BP神经网络优化制备Cu-Ce/TiO_2及其光催化活性研究

采用Cu和Ce对TiO2进行改性,基于正交实验设计和BP神经网络研究了Cu-Ce/TiO2中Cu-Ce对TiO2的摩尔百分数、Cu-Ce/TiO2中CuCe摩尔比及Cu-Ce/TiO2烧结温度对Cu-Ce/TiO2光催化降解甲醛溶液性能的影响.同时,对Cu-Ce/TiO2制备方案进行了优化,并运用X射线衍射仪、扫描电子显微镜和紫外-可见分光光度计对最佳条件下制备的Cu-Ce/TiO2进行表征.结果表明,优化的制备条件为Cu-Ce/TiO2中Cu-Ce对TiO2的摩尔百分数为2.88%,Cu-Ce/TiO2中Cu-Ce的摩尔比为1∶1,Cu-Ce/TiO2的烧结温度为570℃.共掺杂Cu离子和Ce离子能有效避免掺杂TiO2晶格内部表层和近表层产生较多的位错,从而抑制晶格畸变增大;诱导TiO2中锐钛矿型晶体向金红石型晶体转变的能力增强,有效抑制电子-空穴对的复合,产生介电局域效应.     

NaClO_2/氨水溶液同时脱除SO_2和NO的热力学研究

利用化学热力学基本原理分别对NaClO2/氨水溶液同时脱除SO2、NO的反应过程中摩尔反应吉布斯自由能变、摩尔反应焓变、化学反应平衡常数以及化学反应达到平衡时的SO2和NO的分压力进行了计算,结果表明：利用NaClO2/氨水溶液同时脱除SO2、NO是可行的,且SO2和NO的脱除效率几乎可以达到100%。     

Modeling Flow Through a One-Dimensional Multi-Layered Soil Profile Using the Method of Lines

The vertical flow of water through horizontal layers of soil is considered using the Method of Lines. Continuity of mass principles are used to develop the interface boundary conditions, by introducing fictitious points at the interface, and the boundary conditions are handled using explicit and iterative approximations. Both the pressure based, and the water content based forms of Richards' equation are solved using the Method of Lines. The solutions obtained are compared with some particular analytic solutions obtained from the literature, and the results show that good accuracy can be achieved. It is also shown that the water content model can handle a large discontinuity at the interface when compared against the analytical solution. This result is also confirmed against a numerical example from the literature, and was effective for relatively dry initial conditions.     

Initial Changes in Refilled Lysimeters Built with Metal Polluted Topsoil and Acidic or Calcareous Subsoils as Indicated by Changes in Drainage Water Composition

Soil translocation for recultivation of soil removed from construction sites and for the preparation of refilled lysimeters inevitably involves disturbance of soil structure, and, if intermediate storage is included, also drying and rewetting of the soil. We report on an experiment with model forest ecosystems, where uncontaminated forest subsoils were covered with non-contaminated or freshly heavy metal (mainly Zn and Cu) contaminated topsoil in large lysimeters. Monitoring of the chemical composition of the drainage water revealed two distinct soil conditioning phases. During an initial phase of about a year strongly elevated nitrate and sulfate concentrations occurred that were attributed to a mineralisation flush caused by the increased accessability of mineralisable nitrogen and sulfur in destroyed aggregates. These effects were significantly larger in lysimeters with calcareous subsoil than in those with acidic subsoil. The second phase was characterised by a gradual decrease in dissolved organic carbon and sulfate concentrations, in particular in the acidic subsoil. This decrease may be attributed to the depletion of pools made accessible during aggregate destruction or the formation of new aggregates. These chemical changes had only little effects on the concentrations of copper and zinc in the drainage water. Based on our results, it can be concluded that large refilled lysimeters can be used for many purposes without risk of compromised results, if a conditioning phase of about 1 year with sufficiently moist soil conditions is respected. Nevertheless, gradual changes in soil chemical characteristics still occur after this initial phase. Implications for the recultivation of sites using relocated soils are discussed.     

SnAgCu焊料中Sn元素在模拟土壤溶液中的浸出行为

研究了Sn-3.5Ag-0.75Cu无铅焊料及其与Cu基板的钎焊接头在模拟土壤的NaCl,NaCl-Na2SO4和NaCl-Na2SO4-Na2CO3溶液中Sn元素的浸出行为.结果表明:焊料在NaCl-Na2SO4-Na2CO3溶液中Sn的浸出相对严重;而接头在NaCl溶液中Sn的浸出量最多.在Sn浸出量多的焊料和接头表面形成厚而疏松的腐蚀产物,XRD分析表明其产物主要由SnO,SnO2和Sn4(OH)6Cl2组成.动电位极化测试分析表明接头中Cu基板与焊料合金之间的电偶腐蚀是焊料合金与接头在同种溶液中Sn元素浸出差异的主要原因.     

直升机机载产品环境鉴定试验故障分析

目的探究机载产品在鉴定试验阶段故障频发的原因,并改进机载产品研制流程中的不足之处。方法收集某型直升机机载产品50项环境鉴定试验故障,并对环境试验故障进行分析。结果环境试验故障主要为三防及振动试验故障,其故障发生的原因主要为材料及表面处理方法选用不当、设计缺陷和质量控制程序不够严格。结论针对该分析结果提出机载产品在设计过程中,需要通过尽早安排环境研制性试验、建立环境数据库、模拟仿真进行环境适应性设计和加强质量管理等措施,避免机载产品在鉴定试验阶段故障频发的问题。