氮掺杂TiO2介孔光催化剂降解腐殖酸的研究

 以甲酰胺为氮源,钛酸四丁酯为钛源,P123为模板剂,采用溶胶-凝胶法制备了N-TiO2,并利用X-射线粉末衍射(XRD)、BET、分子荧光(PL)等技术对催化剂进行了表征.结果表明, N-TiO2主要以锐钛矿型存在,加入适量模板剂可使N-TiO2具有介孔结构,比表面积达到111.767m2/g,并能使其光生电子与空穴的复合率降低,采用5%P123制备的N-TiO2催化剂(10g/L),对腐殖酸钠(5mg/L)光催化降解,2h后其降解率可达98%,反应符合一级动力学.     

Catalytic oxidation of benzene over nanostructured porous Co3O4-CeO2 composite catalysts

The three-dimensional structured Co₃O₄-CeO₂ oxides with Co/Ce molar ratio 16:1 gave the highest catalytic activity, which provided more surface hydroxyl groups and more surface oxygenated species.     

孔径调变对MCM-41分子筛吸附VOCs性能的影响

采用3种不同碳链长度的季铵盐表面活性剂C_nTAB(n=8,12,16)为模板剂,分别合成8-MCM-41、12-MCM-41和16-MCM-41介孔分子筛,并以甲苯、邻二甲苯、均三甲苯为吸附对象,考察了介孔分子筛动态吸附VOCs的性能.结果表明,通过减少表面活性剂的碳链长度,可以成功地把MCM-41分子筛的孔径调变为4.1、3.2和2.4 nm.吸附实验结果表明,当MCM-41孔径减小时,其对低浓度甲苯、邻二甲苯的吸附量大幅上升,均三甲苯存在孔道扩散效应,其吸附量增加不明显.吸附等温线表明,在2.4 nm孔道内,3种芳烃分子均属于典型的Langmuir单分子层吸附;当孔径大于2.4 nm时,芳烃分子出现明显的多层吸附和毛细凝聚现象.     

三维有序介孔Co3O4非均相活化单过硫酸氢钾降解罗丹明B

以多孔硅KIT-6为模板,采用纳米浇筑法制备三维有序介孔Co_3O_4,利用比表面积测试仪(BET)、高倍投射电子显微镜(H-TEM)、X射线衍射光谱(XRD)、X射线光电子能谱(XPS)、傅里叶变换红外光谱(FT-IR)等方法进行表征,并首次将其应用于催化单过硫酸盐降解罗丹明B.结果表明,三维有序介孔Co_3O_4具有丰富的空间介孔结构和巨大的比表面积,对单过硫酸盐的催化活性远强于传统纳米级Co_3O_4.较高的催化剂投加量和较高的单过硫酸盐浓度有利于罗丹明B的脱色.在反应体系中出现Cl-和H2PO-4能够加速罗丹明B的脱色,而出现NO_3~-、SO_4~(2-)和HCO_3~-则会抑制罗丹明B的去除.通过自由基鉴定实验发现,硫酸自由基是导致罗丹明B脱色的主导活性自由基.三维有序介孔Co_3O_4经过多次重复使用后仍表现出良好的催化活性.     

磷酸水热预处理制备高比表面积高介孔率活性炭

以锯末为原材料,采用磷酸水热预处理后活化的工艺制备高介孔率活性炭,以比表面积和孔容为评价标准,通过单因素实验探究了酸料比、活化温度、活化时间对活性炭比表面积及总孔容的影响规律,验证了该工艺的可行性.最优条件下所制备的活性炭比表面积为2579 m~2·g~(-1),介孔率达到96.6%,充分说明磷酸水热预处理工艺能够显著提高活性炭介孔孔容占比.亚甲基蓝(MB)吸附实验数据与Redlich-Peterson模型拟合度较好,样本活性炭对MB的吸附为单分子层吸附,最大单层吸附量为618.35 mg·g~(-1),接近于实验测试值632.79 mg·g~(-1),表明该方法制备的活性炭具有良好的MB吸附性能.     

高键合量苯基化MCM-41的合成及其吸附特质

采用正硅酸乙脂(TEOS)为硅源,以十六烷基三甲基溴化铵(CTAB)为结构模板剂,用三甲氧基苯基硅烷(TMPS)作偶联剂,在碱性介质中合成苯基修饰MCM-41(Phenyl-MCM-41),对比研究了合成方法和脱模方式。结果表明,在分步合成法中,采用酸萃取脱模方式不仅可除去表面活性剂模板剂,而且MCM-41表面的Si-OH反应活性较高,有利于提高键合量;室温条件下,采用TEOS和TMPS共水解缩聚一步直接合成Phenyl-MCM-41,可进一步提高有机键合量,且高键合量的介孔复合体具有高的热稳定性和很强的疏水性。以Phenyl-MCM-41作为固相微萃取(SPME)的吸附涂层材料,与HPLC联用,考察了对水样中邻苯二甲酸酯的吸附分离性质及其在黄河水样中的分析应用,该法具有操作简单、吸附速度快、线性范围宽和灵敏度高的特点。     

高效去除Cd2+介孔硅酸钙的制备优化及表征

为了进一步研制高效、廉价的Cd²⁺吸附剂,从介孔硅酸钙（CSH）的制备与优化出发,选择钙硅比（Ca/Si）、表面活性剂种类及其用量为因素,采用正交试验探讨CSH的最优制备条件,并结合扫描电镜（SEM）、红外光谱（FTIR）、比表面积测试（BET）、X-射线衍射分析（XRD）,对CSH的结构形貌、材料性能进行评价.结果表明,各因素对合成材料吸附性能的影响顺序为：表面活性剂种类 > 表面活性剂用量 > Ca/Si;最优制备条件为：Ca/Si=1：1,以聚乙二醇（PEG）为表面活性剂,表面活性剂添加量为2%;表面活性剂的添加能显著提高材料的吸附性能,最优条件下制备的介孔硅酸钙对Cd²⁺的饱和吸附容量高达687.71 mg·g^-1,吸附等温线符合Langmiur模型;合成的水化硅酸钙为介孔结构,为狭缝孔,呈纳米花状,比表面积为333.47 m²·g^-1,BJH孔径为10.9 nm,孔隙度为2.199 cm³·g^-1;巨大的比表面积、高孔隙度、表面丰富的活性—OH及材料富含可交换态Ca²⁺,以及能与Cd²⁺发生吸附沉淀、表面络合和离子交换,致使其具有优异的吸附性能,有望为Cd²⁺污染水体治理和土壤修复提供潜在优势新材料.     

新型净水材料的吸附特性研究

采用高效液相色谱分析微污染水原水、新型材料吸附后出水及活性炭吸附后出水的特征，对比新型材料及活性炭对微污染水中不同分子量的有机物的吸附效果，以此间接反映两种材料的孔径分布特点，分析两种材料的不同吸附特性，并讨论新型净水材料的吸附机理。     

Adsorption of benzene, cyclohexane and hexane on ordered mesoporous carbon

Ordered mesoporous carbon(OMC) with high specific surface area and large pore volume was synthesized and tested for use as an adsorbent for volatile organic compound(VOC)disposal. Benzene, cyclohexane and hexane were selected as typical adsorbates due to their different molecular sizes and extensive utilization in industrial processes. In spite of their structural differences, high adsorption amounts were achieved for all three adsorbates, as the pore size of OMC is large enough for the access of these VOCs. In addition, the unusual bimodal-like pore size distribution gives the adsorbates a higher diffusion rate compared with conventional adsorbents such as activated carbon and carbon molecular sieve. Kinetic analysis suggests that the adsorption barriers mainly originated from the difficulty of VOC vapor molecules entering the pore channels of adsorbents. Therefore, its superior adsorption ability toward VOCs, together with a high diffusion rate, makes the ordered mesoporous carbon a promising potential adsorbent for VOC disposal.     

Mesoporous silicas synthesis and application for lignin peroxidase immobilization by covalent binding method

Immobilization of enzymes on mesoporous silicas (MS) allows for good reusability. MS with two-dimensional hexagonal pores in diameter up to 14.13 nm were synthesized using Pluronic P123 as template and 1,3,5-triisopropylbenzene as a swelling agent in acetate buffer. The surface of MS was modified by the silanization reagents 3-aminopropyltriethoxysilane. Lignin peroxidase (LiP) was successfully immobilized on the modified MS through covalent binding method by four agents: glutaraldehyde, 1,4- phenylene diisothiocyanate, cyanotic chloride and water-soluble carbodiimide. Results showed that cyanotic chloride provided the best performance for LiP immobilization. The loaded protein concentration was 12.15 mg/g and the immobilized LiP activity was 812.9 U/L. Immobilized LiP had better pH stability. Acid Orange II was used to examine the reusability of immobilized LiP, showing more than 50% of the dye was decolorized at the fifth cycle.