机场环境下飞机LY12CZ结构腐蚀损伤预测方法研究

依据LY1 2CZ材料的EXCO溶液浸泡加速腐蚀试验数据、飞机LY 12CZ构件在机场环境下的真实腐蚀损伤数据以及腐蚀损伤等效原则和当量关系原理,获得了该材料在2种环境下腐蚀的当量因子均值(α) =0.023 6,构建了LY12CZ材料于EXCO溶液中浸泡腐蚀的神经网络腐蚀深度预测模型.在此基础上提出了利用所建的神经网...     

缓冲液对微生物燃料电池产电性能影响研究

微生物燃料电池(microbial fuel cell,MFC)应用于废水处理是一项非常有潜力的除污产能的绿色技术.但MFC运行过程中采用磷酸盐缓冲液不符合除污产能要求,增加水体富营养化趋势且增加水处理成本.试验采用单极室微生物燃料电池处理模拟生活污水,以投加PBS(phosphate buffer solution)...     

土壤溶液性质对Zn的形态变化及其微生物毒性的影响

采集了我国具有代表性的12种不同性质土壤,利用基础诱导硝化(SIN)方法测定了不同土壤中锌的微生物毒性阈值,同时利用850离子色谱仪与WHAM6.0模型,测定了溶液不同阴离子组成及自由Zn2+含量,建立了基于不同土壤性质与溶液离子的土壤中Zn毒性预测模型.结果表明,基于SIN测定的不同土壤Zn微生物毒性阈值在不同土壤间有显著差异,其中EC50从196mg/kg至1310mg/kg;EC10值从48mg/kg增加至682mg/kg,不同土壤EC50与EC10的最大值与最小值的比例分别达到了6.68及14.3倍,表明土壤性质对Zn的微生物毒性有非常显著的影响;基于SIN的Zn的毒性阈值ECx(x=10,50)与溶液自由Zn2+浓度的负对数p(Zn2+)间呈正相关关系,表明随着土壤溶液中自由Zn2+值的升高,Zn的毒性逐渐增加.土壤pH值、OC、CEC、F-、Cl-、Ca2+及Mg2+与Zn的毒性阈值ECx(x=10,50)及p(Zn2+)呈正相关关系,其中土壤pH值为最重要的影响因子,偏相关系数均达到极显著水平(P<0.01),其次为OC、CEC及F-,ECx与溶液中NO3-, SO42-呈负相关关系.基于不同主控因子的土壤中Zn毒性阈值(ECx)及P(Zn2+)的预测模型表明,pH值、OC、CEC、F- 四个变量因子分别解释了log(EC50)、log(EC10)及p(Zn2+)预测模型变异的89.9%、81.2%和92.3%.     

利用蚀刻废液生产碱式氯化铜过程中二英类污染物的去除

针对蚀刻废液及其回收后生产的碱式氯化铜产品中二英(PCDD/Fs)和二英类多氯联苯(dl-PCBs)进行了分析研究,并比较了采用去除工艺前后两类污染物含量水平的变化特征.利用高分辨气相色谱/高分辨质谱对样品中PCDD/Fs和dl-PCBs进行分析,结果表明,氯化铜废液中PCDD/Fs和dl-PCBs的平均总浓度分别为264、139 pg·mL-1,而铜氨液中浓度分别为0.09、0.50 pg·mL-1;碱式氯化铜产品中浓度分别为106 pg·g-1(2.79 pg WHO-TEQ2005·g-1)和27.8 pg·g-1(0.69 pg WHO-TEQ2005·g-1);而经过吸附和过滤等去除工艺后,产品中PCDD/Fs和dl-PCBs的TEQ浓度水平分别降低至0.10—0.25 pg WHO-TEQ2005·g-1和0.05—0.72 pg WHO-TEQ2005·g-1,满足欧盟对于矿物源性饲料添加剂中PCDD/Fs和dl-PCBs的限量标准要求.研究表明该工艺能够有效去除利用蚀刻废液生产碱式氯化铜过程中的二英类污染物.     

高温碱间歇式处理对互花米草厌氧发酵特性的影响

以互花米草为原料,采用中温(35±1)℃批式发酵的方式,考察了NaOH高温碱间歇式处理对互花米草厌氧消化过程的影响.结果表明,互花米草一次发酵至产气停止,单位TS产气量为263mL/g,发酵过程中出现酸化现象, pH值最低为5.17.二次发酵原料为一次发酵后的固体残余物,主要组分为可分解有机物以及一些难分解有机物,过程中未出现酸化现象, pH值经短暂下降后很快稳定在7.5左右,累积产气量在一次发酵的基础上提高了46%.互花米草单位TS产气量为383mL/g.消化液中有机酸乙酸含量最大,丙酸和丁酸含量相当.     

Low-temperature CO oxidation over Au-doped 13X-type zeolite catalysts: preparation and catalytic activity

Au-supported 13X-type zeolite (Au/13X) was synthesized using a common deposition–precipitation (DP) method with a solution of sodium carbonate as a precipitate agent. Further testing was conducted to test for catalytic oxidation of CO. A study was conducted on the effects of different preparation conditions (i.e., chloroauric acid concentration, solution temperature, pH of solution, and calcinations temperature) on Au/13X for CO oxidation. In respect to the catalytic activity, the relationship between different the preparation conditions and gold particles in 13X zeolite was analyzed using X-ray diffraction, TEM and XPS. The activity of Au/13X catalysts in CO oxidation was dependent on the chloroauric acid concentration. From XRD results, a higher chloroauric acid concentration induced larger gold nanoparticles, which resulted in lower catalytic activity. Results revealed that higher temperatures induced higher Au loading, homogeneous deposit, and smaller gold clusters on the support of 13X, resulting in higher CO activity. Furthermore, a pH of 5 or 6 generated greater amounts of Au loading and smaller Au particles on 13X than at a pH of 8 or 9. This may be a result of an effective exchange between Au(OH)2Cl2- and Au(OH)₃Cl^- on specific surface sites of zeolite under the pH’s 5 and 6. The sample calcined at 300°C showed the highest activity, which may be due to the sample’s calcined at 200°C inability to decompose completely to metallic gold while the sample calcined at 400°C had larger particles of gold deposited on the support. It can be concluded from this study that Au/13X prepared from a gold solution with an initial chloroauric acid solution concentration of 1.5 × 10^-3 mol·L^-1 gold solution pH of 6, solution temperature of around 90°C, and a calcination temperature of 300°C provides optimum catalytic activity for CO oxidation.     

Leaching characteristics of bisphenol A from epoxy-resin pavement materials

We investigated the leaching characteristics of bisphenol A (BPA) from two kinds of epoxy-resin pavement materials, one containing epoxy resins (EPs) and the other containing epoxy-acrylate resins (EPAs). Both samples contained residual BPA monomer, at levels of 9.0?µg?g^?1 for the EP resin sample and 4.4?µg?g^?1 for the EPA resin sample. These amounts were larger than amounts previously measured for polycarbonate samples. The amount of BPA leached from the samples increased with temperature. The leaching of BPA from EP was more strongly affected by temperature than the leaching from EPA. The pH also affected the amount of leached BPA. The maximum leached amount was observed under alkaline conditions (pH 10.8) for both sample types. The amounts of BPA that might leach from pavement materials during 1?h of heavy rain were estimated to be 0.9?µg?m^?2 for EP and 3.5?µg?m^?2 for EPA. Our results indicate that EPs disposed of in waste landfills without any treatment may be a source of BPA in leachate at landfill sites.     

以缓释肥的形式回收污泥溶解液中磷的研究

以聚合硫酸铁(PFS)为絮凝剂,单宁酸为助凝剂回收污泥溶解液中的磷。研究结果表明:在铁盐投加量为160mg/L,pH为8,单宁酸投加量为10 mg/L条件下,磷酸盐的回收率可达到97.0%。单宁酸促进了混凝沉淀物中磷的释放,表明利用该方法回收磷作为缓释肥的可行性。将沉淀物作为缓释磷肥施用于土壤中能够明显促进黑麦草的生长。     

吸收液对中空纤维膜接触器回收尿液中氨氮的影响

采用中空纤维膜接触器（Hollow Fiber Membrane Contactor, HFMC）回收尿液中的氨氮,系统研究了吸收液类型（H₃PO₄、H₂SO₄和HNO₃）对氨回收效能、水蒸气的跨膜通量和所获液体肥料的影响.结果表明,使用H₂SO₄作为吸收液时氨氮回收效能最优,其次是H₃PO₄和HNO₃.当采用H₂SO₄为吸收液时,氨氮回收率、氨跨膜通量和传质系数分别为84.49%±0.01%、22.92 g·m^-2·h^-1和2.37×10^-6 m·s^-1.HNO₃的挥发性使其从吸收液侧反向跨膜至料液侧,导致氨跨膜传质驱动力变小;此外,NH₃和HNO₃会在膜孔中反应并生成NH₄NO₃气溶胶,增加氨在膜孔中的传质阻力,导致氨氮的回收效能降低.对采用不同吸收液时膜两侧的水的活度差和理论水通量进行了计算,结果表明,随着氨氮的不断跨膜吸收,膜两侧的活度差和水通量逐渐增大,实验结束时水通量分别为7.44×10^-2 kg·m^-2·h^-1（H₃PO₄）、9.06×10^-2 kg·m^-2·h^-1（H₂SO₄）和2.00×10^-2 kg·m^-2·h^-1（HNO₃）.肥料组分分析表明,以H₂SO₄和HNO₃为吸收液可以获得仅含N素的单一液体肥料,以H₃PO₄作吸收液可获得N-P复合肥,（NH₄）₂HPO₄和NH₄H₂PO₄所占的比例分别为88.33%和11.67%.     

非均性多孔介质中生物炭胶体的迁移行为研究

生物炭颗粒在多孔介质中的迁移行为不仅决定了其在环境中的归趋,也极大地影响了被吸附污染物的环境行为.以往的研究主要集中在生物炭胶体在均性多孔介质中的迁移行为,但实际环境介质通常是非均性的,目前对生物炭胶体在非均性多孔介质中的迁移行为知之甚少.本研究采用两种不同粒径的石英砂构建了上下两层非均性填充柱（上层细颗粒,下层粗颗粒）,研究了生物炭胶体在非均性多孔介质中的迁移和截留行为,考察了溶液离子强度和pH对生物炭胶体迁移能力的影响.研究结果表明在非均性多孔介质中,生物炭胶体具有很高的迁移能力,在离子强度为1~50 mmol·L^-1,pH为4.0~11.0条件下,生物炭胶体的迁移率达40.2%~88.0%.非均性介质中生物炭胶体的截留曲线表现为非单调型曲线,截留量峰值往往出现在细-粗石英砂的交界面处（细石英砂侧）,这与非均性介质中显著的电荷异质性、介质尺寸异质性和迁移过程中传质通量异质性有关.生物炭胶体在上层细石英砂中的截留量显著大于其在下层粗石英砂中的截留量,表明上层细石英砂是影响生物炭胶体迁移行为的关键层.随着溶液离子强度增加,生物炭胶体自团聚作用增强,其与石英砂介质间界面作用能垒降低,因而生物炭胶体的迁移能力减弱.由于生物炭胶体与细石英砂间的物理张力作用趋于显著,增加离子强度提高了生物炭胶体在上层细石英砂中的截留比率.中性和碱性条件下生物炭胶体的迁移能力较强,而在酸性条件下,生物炭胶体表面电负性显著降低,团聚体粒径增大,生物炭胶体的迁移能力较弱.降低溶液pH增加了生物炭胶体在上层细石英砂中的截留比率.本研究的结果将有利于人们更好地了解生物炭胶体在复杂多孔介质中的迁移行为,为全面评估生物炭的潜在环境风险提供理论支持.