垃圾渗滤液的混疑处理实验研究

用聚合氯化铝(PAC)．聚丙烯酰胺(PAM)．复合混凝剂(90％PAC 10％PAM)及试剂A(一种壳聚糖)等4种混凝剂在不同pH及不同投加量的情况下．对垃圾渗滤液COD的去除效果进行了比较分析。实验结果表明。复合混凝剂及试剂A的处理效果明显优于PACPAM。在pH值5.5和8时。复合混凝剂投加量为400mg／L时。COD的去除率分别为38．63％和37．84％：试剂A在pH为8．投加量为100mg／L时。对COD的去除率达到39．85％。     

阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

无机高分子絮凝剂的开发与应用进展

主要介绍了各种离子型和复合型无机高分子絮凝剂的种类、原料来源、合成工艺应用情况及其絮凝机理，对无机高分子絮凝剂的发展提出了几点建议。     

EFFECTIVENESS OF POLYACRYLAMIDE (PAM) IN IMPROVING RUNOFF WATER QUALITY FROM CONSTRUCTION SITES1

ABSTRACT: Erosion from construction sites significantly affects water quality in receiving streams. A rainfall simulator was used to evaluate the effectiveness of different methods for controlling erosion from construction sites. Erosion control methods investigated included dry and liquid applications of polyacrylamide (PAM), hydroseed, and straw mulch. Fertilizer was also applied to each plot to examine the effectiveness of the methods in reducing nutrient losses in runoff. Runoff samples were analyzed for total suspended solids (TSS), nitrate, total Kjeldahl nitrogen (TKN), ammonium, total phosphorus (TP), and orthophosphate. Among all treatments investigated, straw mulch was the most effective treatment for controlling TSS and nutrient losses during short term and long term simulations. The low liquid PAM (half the recommended PAM) treatment resulted in the highest reduction in runoff, TSS bound nitrogen, and total nitrogen (TN) concentrations and loadings. The study results indicate that a high application rate (twice the recommended rate) of PAM could actually increase runoff and TSS losses. At a low application rate, both liquid and dry PAM were effective in reducing TSS and nutrient losses in runoff. However, application of the liquid form of PAM to construction sites is more practical and perhaps more economical than applying the PAM in the dry form.     

Degradation of polyacrylamide (PAM) and methane production by mesophilic and thermophilic anaerobic digestion: Effect of temperature and concentration

• PAM degradation in thermophilic AD in comparison with mesophilic AD. • PAM degradation and its impact on thermophilic and mesophilic AD. • Enhanced methane yield in presence of PAM during thermophilic and mesophilic AD. • PAM degradation and microbial community analysis in thermophilic and mesophilic AD. Polyacrylamide (PAM) is generally employed in wastewater treatment processes such as sludge dewatering and therefore exists in the sludge. Furthermore, it degrades slowly and can deteriorate methane yield during anaerobic digestion (AD). The impact or fate of PAM in AD under thermophilic conditions is still unclear. This study mainly focuses on PAM degradation and enhanced methane production from PAM-added sludge during 15 days of thermophilic (55°C) AD compared to mesophilic (35°C) AD. Sludge and PAM dose from 10 to 50 g/kg TSS were used. The results showed that PAM degraded by 76% to 78% with acrylamide (AM) content of 0.2 to 3.3 mg/L in thermophilic AD. However, it degraded only 27% to 30% with AM content of 0.5 to 7.2 mg/L in mesophilic AD. The methane yield was almost 230 to 238.4 mL/g VSS on the 8th day in thermophilic AD but was 115.2 to 128.6 mL/g VSS in mesophilic AD. Mechanism investigation revealed that thermophilic AD with continuous stirring not only enhanced PAM degradation but also boosted the organics release from the sludge with added PAM and gave higher methane yield than mesophilic AD.     

羟基乙叉二膦酸镀铜废液的处理及Cu~(2+)的高附加值资源化回收

采用Na BH4还原法将羟基乙叉二膦酸(HEDP)镀铜废液中的Cu~(2+)制备成纳米铜粉,并采用聚丙烯酰胺(PAM)对还原反应后的废液进行絮凝处理。研究了n(Cu~(2+))∶n(Na BH4)、还原反应温度、还原反应时间及PAM添加量对废液中剩余Cu~(2+)质量浓度的影响,并对回收的纳米铜粉进行了XRD和TEM表征。实验结果表明:当n(Cu~(2+))∶n(Na BH4)=4∶6、还原反应温度为50℃、还原反应时间为2 h时,废液中剩余Cu~(2+)质量浓度降低至1.1 mg/L,Cu~(2+)还原率达99.99%;可获得粒径为20~45 nm的近球型、高纯度、由多晶组成的纳米铜粉;当PAM添加量为10 mg/L时,废液中剩余Cu~(2+)质量浓度降至0.35 mg/L以下,达到GB 21900—2008《电镀污染物排放标准》(小于0.5 mg/L)的要求。     

液态聚合氯化铝铁深度除磷的优化研究

以北京市生活废水为研究对象,考察了液态聚合氯化铝铁及与聚丙烯酰胺(PAM)协同作用下除磷效果及其影响因素。结果表明,液态聚合氯化铝铁与PAM复合作用时对除磷效果有一定的提高,明确了PAM的最佳投加量、最佳搅拌强度、最佳搅拌时间和pH,并得出了影响混凝效果因素的主次顺序为:pH值搅拌时间搅拌强度投加量。     

电催化氧化法处理阳离子染料废水的试验研究

以结晶紫作为阳离子染料,采用电催化氧化法对阳离子染料溶液进行了电解脱色处理试验,研究了电流密度、电解质种类、电解质浓度、pH值等对该溶液脱色率的影响,测定了电解时溶液中生成的余氯浓度和溶液的紫外-可见吸收光谱曲线,并对不同电解时间的溶液的吸光度进行了归一化计算。结果表明:随着电解时间的延长,水溶液中活性氯浓度不断上升,经一定时间后达到最大值;在电催化和活性氯的协同作用下,阳离子染料结晶紫分子中的大π共轭体系被破坏、苯环结构基本瓦解,溶液快速脱色;在电流密度为5.1mA/cm2、NaCl浓度为4g/L、pH值为9.41的条件下,初始浓度为100mg/L的结晶紫溶液经过20min的电解,其脱色率可高达98.31%。     

生物淋滤-PAC与PAM联合调理城市污泥

采用生物淋滤-聚合氯化铝(PAC)与聚丙烯酰胺(PAM)联合使用工艺对城市污泥进行了调理研究.结果表明,在固定单质硫投量为3 g.L-1的条件下,投加亚铁离子能明显加快污泥生物淋滤速率;FeSO4.7H2O投量为8 g.L-1时,污泥pH降至2约需1.5 d.生物淋滤显著改善了污泥的脱水性能,生物淋滤后使污泥比阻从6.45×1010 s2.g-1降到1.45×1010 s2.g-1,降低了77.52%,但污泥仍属于难脱水污泥.回调淋滤污泥pH至6,投加PAC及PAM对淋滤污泥进行强化调理.结果表明,单独使用PAC与PAM的最佳投量分别为200 mg.L-1和50 mg.L-1;联合使用PAC与PAM时,PAC与PAM的最佳投量分别为100mg.L-1和25 mg.L-1,污泥比阻和滤饼含水率分别为2.02×108 s2.g-1和74.81%,污泥属于易脱水污泥.与单独使用PAC与PAM相比,PAC与PAM联合使用调理污泥费用低、处理效果好.     

陶瓷印花废水处理的混凝剂及工艺条件

采用混凝剂聚合氯化铝（PAC）、聚丙烯酰胺（PAM）、聚合硫酸铁（PFS）对陶瓷印花废水进行混凝沉降处理，监测水样的吸光度、浊度、悬浮物，以脱色率、浊度去除率、悬浮物去除率评价混凝处理的效果。结果表明：PAC是陶瓷印花废水沉降处理的理想混凝剂；水样的吸光度、浊度、悬浮物随混凝剂用量增大和沉降时间延长而呈降低趋势，而脱色率、浊度去除率、悬浮物去除率随混凝剂和沉降时间的增大呈增大的趋势；PAC投加量为20mg／L，沉降时间约为24h，水样脱色率达到90．0％，而当PAC投加量达到100mg／L，沉降时间约为4h，陶瓷印花水的脱色率可达到96．0％。证明了药剂用量的增加与沉降时间的延长对混凝过程具有增效作用。