石家庄市春季大气颗粒物的铅污染特征

为了解石家庄市2016年春季大气颗粒物的铅污染特征及来源,利用单颗粒气溶胶质谱仪(SPAMS),分析了大气中含铅颗粒的化学成分。结果表明: 研究期间大气环境中含铅颗粒数浓度共出现11次跳跃式升高,跳跃时间段内石家庄均处于轻度污染过程。从成分分析来看,含铅颗粒分为纯铅颗粒、Pb与K(Pb-K)、OC(Pb-OC)、Cl(Pb-Cl)、混合颗粒等八大类。观测结果表明:Pb-K颗粒最多,占到含铅颗粒的84.4%；其次为纯铅颗粒,占比为13.0%。与石家庄市污染源谱库比对进行来源解析,得到Pb-K颗粒主要来自生活垃圾焚烧源, 纯铅颗粒主要来自工业源。结合石家庄市大气污染源排放清单和后向气流轨迹分析,推测含铅颗粒可能来自市区西南方向某区县的生活垃圾焚烧企业。     

钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3，并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD，SEM，FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构，其中，LaFe0.9Mn0.1O3的结构稳定，比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高，且稳定性好，连续使用5次后催化活性未见明显减弱；在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下，COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%，BOD5/COD由0.02提升至0.40，可生化性大幅提高。     

CS/PEG/PFT膜制备及对含铜废水的处理

实验将溶胶凝胶法和高分子辅助倒相法结合,制备出一种新型的壳聚糖/聚乙二醇/亚铁氰化钾钛(CS/PEG/PFT)复合膜,通过FT-IR和SEM对膜进行表征后,将其用于模拟铜废水的吸附和脱附实验,并探究出膜吸附的最佳工艺条件为:p H 5.50、实验温度55℃、实验时间2 h,该条件下,膜对铜离子最大吸附量为9.85 mg/g,去除率达到95%以上。CS/PEG/PFT膜的除铜过程符合Langmuir等温吸附方程(y=0.0597x+0.0168),线性相关度达到0.9917。     

γ-Al2O3负载多金属复合催化剂选择性催化还原烟气脱硝

以γ-Al₂O₃作为载体，先后负载CeO₂，MnC₂O₄，Fe（NO₃）₃，CrO₃，Ni（NO₃）₂，NH₄VO₃等多种金属组分制备γ-Al₂O₃负载多金属复合催化剂，并用于模拟烟气的选择性催化还原脱硝。通过SEM和XRD技术对催化剂进行了表征。表征结果显示：Fe，Mn，Cr的添加能增加催化剂的低温催化活性、提高催化剂的N₂选择性;γ-Al₂O₃对活性金属氧化物的负载效果良好。实验结果表明：各金属化合物的最佳加入量为 w（MnC₂O₄·2H₂O）=20%，w（Fe（NO₃）₃·9H₂O）=15%，w（CrO₃）=10%，w（Ni（NO₃）₂·6H₂O）=5%，w（NH₄VO₃）=10%，w（CeO₂）=5%，w（γ-Al₂O₃）=35%;以在最佳正交实验条件下制得的γ-Al₂O₃负载多金属复合物为催化剂，在脱硝反应温度为205 ℃的条件下，NO转化率为96.7%;γ-Al₂O₃负载多金属复合催化剂经5次重复使用，NO转化率仍可稳定在94%左右。     

Safety assessment of the film boiling chemical vapor infiltration (FB-CVI) process through a system-theoretic accident model and process (STAMP)

Film boiling chemical vapor infiltration (FB-CVI) is considered as one of the fastest process methodologies for manufacturing carbon-carbon (C–C) composite products and possesses various advantages compared to conventional methodologies. However, there are safety concerns associated with this process for large-scale manufacturing, mainly owing to the intrinsic nature of the precursor and the process conditions. Considering the multifunctional interactions of the various systems during the process, a system-theoretic process analysis (STPA)/system theoretic accident model and process (STAMP) model is used to perform a safety analysis of the hazardous states of the FB-CVI process at the system level. As a case study, the FB-CVI process equipment employed for the manufacturing of C–C composites is considered. The safety constraints present in the system are assessed for adequacy through a hazard analysis by STPA/STAMP. The analysis through STPA/STAMP demonstrated the capability to create proactive strategies for the design and realization of process equipment that can be employed to manufacture C–C composite products through the FB-CVI process.     

Compositions and sources of organic acids in fine particles (PM2.5) over the Pearl River Delta region, south China

Organic acids as important constituents of organic aerosols not only influence the aerosols' hygroscopic property, but also enhance the formation of new particles and secondary organic aerosols. This study reported organic acids including C14–C32fatty acids, C4–C9dicarboxylic acids and aromatic acids in PM2.5collected during winter 2009 at six typical urban, suburban and rural sites in the Pearl River Delta region. Averaged concentrations of C14–C32fatty acids, aromatic acids and C4– C9 dicarboxylic acids were 157, 72.5 and 50.7 ng/m3, respectively. They totally accounted for 1.7% of measured organic carbon. C20–C32fatty acids mainly deriving from higher plant wax showed the highest concentration at the upwind rural site with more vegetation around, while C14–C18fatty acids were more abundant at urban and suburban sites, and dicarboxylic acids and aromatic acids except 1,4-phthalic acid peaked at the downwind rural site. Succinic and azelaic acid were the most abundant among C4–C9dicarboxylic acids, and 1,2-phthalic and 1,4-phthalic acid were dominant aromatic acids. Dicarboxylic acids and aromatic acids exhibited significant mutual correlations except for 1,4-phthalic acid, which was probably primarily emitted from combustion of solid wastes containing polyethylene terephthalate plastics. Spatial patterns and correlations with typical source tracers suggested that C14–C32fatty acids were mainly primary while dicarboxylic and aromatic acids were largely secondary. Principal component analysis resolved six sources including biomass burning, natural higher plant wax, two mixed anthropogenic and two secondary sources; further multiple linear regression revealed their contributions to individual organic acids. It turned out that more than 70% of C14–C18fatty acids were attributed to anthropogenic sources, about 50%–85% of the C20–C32fatty acids were attributed to natural sources, 80%–95% of dicarboxylic acids and 1,2-phthalic acid were secondary in contrast with that 81% of 1,4-phthalic acid was primary.     

Characteristics of atmospheric particles and heavy metals in winter in Chang-Zhu-Tan city clusters, China

To understand the pollution characteristics of atmospheric particles and heavy metals in winter in Chang-Zhu-Tan city clusters, China, total suspended particulate(TSP) and PM10samples were collected in cities of Changsha, Zhuzhou and Xiangtan from December 2011 to January 2012, and heavy metals of Cd, Pb, Cr, and As were analyzed. It shows that the average TSP concentration in Changsha, Zhuzhou and Xiangtan were(183 ± 73),(201 ± 84) and(190 ± 66) μg/m3respectively, and the average PM10 were(171 ± 82),(178 ± 65) and(179 ± 55) μg/m3respectively. The lowest TSP and PM10concentrations occurred at the background Shaping site of Changsha. The average ratio of ρ(PM10)/ρ(TSP) was 91.9%, ranging from 81.3% to 98.9%. Concerning heavy metals, in TSP samples, the concentration of Cr, As, Cd and Pb were 28.8–56.5, 18.1–76.3, 3.9–26.1 and 148.0–460.9 ng/m3, respectively, while in PM10samples, were 16.4–42.1, 15.5–67.9, 3.3–22.2 and 127.9–389.3 ng/m3, respectively. The enrichment factor of Cd was the highest, followed by Pb and As, while that of Cr was the lowest.     

不同养殖模式池塘沉降颗粒营养物质组成特征

2012年4~10月采用自制沉降颗粒收集装置收集主养草鱼和黄颡鱼池塘生态系统中沉降颗粒物,开展了颗粒物质的垂直沉降量以及沉降颗粒中碳氮磷等营养物质的组成及沉降通量的季节变化特征的研究。结果表明:养殖可以显著提高池塘颗粒物质的垂直沉降量,主养草鱼池塘中颗粒物质垂直沉降量显著高于主养黄颡鱼池塘(p0.01),且两种养殖模式池塘颗粒物质沉降量随着养殖时间推进有显著增加的趋势。主养草鱼的池塘中颗粒物质垂直沉降量在100.39~414.66g/(m2·d)之间变化,平均为224.46g/(m2·d),主养黄颡鱼池塘中沉降颗粒物质垂直沉降量在34.14~272.91g/(m2·d)之间变化,平均为155.18g/(m2·d)。两种养殖模式沉降颗粒的碳氮磷成分在养殖周期内的变化规律不明显但具有相似的变化趋势,主养黄颡鱼池塘沉降颗粒中TN、TC、TOC和TON的含量均比同时期主养草鱼高,且均随着养殖时间的推进,沉降颗粒中碳氮磷的总量呈增加趋势。两种养殖模式池塘沉降颗粒中的C/N比值与沉积物中的C/N比值较为接近,表明沉降颗粒与沉积物营养物质来源具有一定的相似性,同时养殖系统内养殖对象与其所处环境的相互依存和相互影响对颗粒物质的产生以及沉降具有重要作用。     

壳聚糖活性污泥复合吸附剂的制备研究

为了提高污泥细胞吸附重金属离子的应用能力,采用壳聚糖包埋固定活性污泥,制备了粒径2~3 mm的壳聚糖活性污泥复合吸附剂SCTS.以吸附溶液中CrO2-4的吸附率为指标,通过单因素实验对制备过程中采用的2种固化液及5种发泡剂进行比选,考察了固化液浓度、发泡剂量、交联剂量、活性污泥与壳聚糖用量比值及发泡温度对SCTS吸附能力的影响,由正交实验确定影响因素主次顺序及最优水平组合.结果发现,固化液浓度、发泡剂量、污泥与壳聚糖用量比值及发泡温度对SCTS吸附能力影响较强,影响次序为固化液浓度发泡剂量活性污泥与壳聚糖用量比值发泡温度.最优水平组合为4 g·L-1三聚磷酸钠(STPP)固化液、剂量为吸附剂质量10%的NH4HCO3发泡剂、活性污泥与壳聚糖用量比值0.5、发泡温度100℃,此时CrO2-4吸附率最高可达97.3%.该吸附剂的制备研究为污泥的资源化利用探索了新的途径.     

江西钨矿周边土壤重金属生态风险评价:不同评价方法的比较

对江西省大余县某钨矿区周边的农田土壤进行调查分析,并采用不同的方法对土壤进行评价,结果表明,土壤As、Pb、Zn、Cu和Ni的含量范围分别为15.33—154.65 mg·kg-1、156.29—346.98 mg·kg-1、47.73—277.72 mg·kg-1、19.06—210.24 mg·kg-1和12.00—35.11 mg·kg-1,一些土壤样点的As、Pb、Zn和Cu含量已超过国家土壤环境质量二级标准.利用地累积指数法对土壤进行评价,结果表明土壤均受到As、Pb、Zn、Cu和Ni不同程度的污染;根据CPI(综合污染指数)评价标准,65.7%的土壤处于污染状态;利用TCLP法对土壤生态风险进行评价,结果显示所有土壤并未受到重金属的污染,以内梅罗综合污染指数法对土壤进行综合评价,结果表明该农田土壤重金属生态风险处于安全范围;以潜在生态危害指数法评价,发现Pb、As和Cu达到或超过中等生态风险的样点分别占37.14%、25.72%和2.86%,其他重金属污染风险均属轻微以下.不同评价方法得出的评价结果有差异,人们在评价重金属污染土壤时要根据评价的目的慎重选择合适的评价方法.