Wastewater treatment with multilayer media of waste and natural indigenous materials

Wastewater treatment using waste materials (refuse concrete, waste paper and charcoal) and natural indigenous rocks (andesite, limestone, granite and nitrolite) in the form of multilayer media was investigated. The removal of suspended solids (SS), phosphate ion, nitrate ion, ammonium ion, toxic metals and chemical oxygen demand (COD) were evaluated for the multilayer wastewater treatment system. Effective removal of heavy metals such as cadmium, chromium, mercury and lead was demonstrated. SS and phosphate ion were removed with relatively high efficiency and the COD after treatment was lessened using certain combinations of media. The present wastewater treatment system is simple, convenient and low cost. Therefore, this method can be applied in small scale plants for wastewater treatment in local and nonexclusive areas.     

Morphological,physiological and biochemical responses of two Australian biotypes of Parthenium hysterophorus to different soil moisture regimes

Parthenium weed is a problematic invasive species in several countries around the world. Although it is considered to be a highly invasive species within Australia, not all biotypes of parthenium weed exhibit the same ability in regard to aggressive colonization and distribution. Differences among biotypes, particularly in regard to environmental ranges as a possible basis for this variation, have not always been elucidated. To determine whether drought tolerance could be a factor in biotype demographics, we quantified the biological responses of two Australian parthenium weed biotypes known to differ in invasive ability Clermont (“high”) and Toogoolawah (“low”) to 100, 75 and 50% of soil water holding capacity (WHC). The Clermont biotype had greater vegetative growth, seed production and chlorophyll content than Toogoolawah, across all moisture levels. Net photosynthesis, stomatal conductance, internal CO₂ concentration, seed production per plant, 1000 seed weight and subsequent germination percentage were also higher for Clermont than for Toogoolawah and were maximum at 75% WHC. Clermont plants also had higher total soluble sugar, phenolics and free proline content than Toogoolawah, and a significant increase in the levels of all of these biochemicals was observed at 50% WHC. In conclusion, Clermont grew and reproduced better than Toogoolawah across all moisture regimes consistent of enhanced invasive ability of this biotype. Overall, the ability of parthenium weed to maintain good growth, physiology and seed production under moisture stress may enable it to colonize a wide range of Australian environments.

     

Hydrogen sulfide ameliorates lead-induced morphological, photosynthetic, oxidative damages and biochemical changes in cotton

Poisonous lead (Pb), among heavy metals, is a potential pollutant that readily accumulates in soils and thus adversely affects physiological processes in plants. We have evaluated how exogenous H₂S affects cotton plant physiological attributes and Pb uptake under Pb stress thereby understanding the role of H₂S in physiological processes in plants. Two concentrations (0 and 200 μM) of H₂S donor sodium hydrosulfide (NaHS) were experimented on cotton plants under Pb stress (0, 50, and 100 μM). Results have shown that Pb stress decreased plant growth, chlorophyll contents, SPAD value, photosynthesis, antioxidant activity. On the other hand, Pb stress increased the level of malondialdehyde (MDA), electrolyte leakage (EL), and production of H₂O₂ and uptake of Pb contents in all three parts of plant, viz. root, stem, and leaf. Application of H₂S slightly increased plant growth, chlorophyll contents, SPAD value, photosynthesis, and antioxidant activity as compared to control. Hydrogen sulfide supply alleviated the toxic effects of lead on plant growth, chlorophyll contents, SPAD value, photosynthesis, and antioxidant activity in cotton plants. Hydrogen sulfide also reduced MDA, EL, and production of H₂O₂ and endogenous Pb levels in the three mentioned plant parts. On the basis of our results, we conclude that H₂S has promotive effects which could improve plant survival under Pb stress.     

Hybrid Composites Made from Oil Palm Empty Fruit Bunches/Jute Fibres: Water Absorption,Thickness Swelling and Density Behaviours

In this research, hybrid composite materials were prepared from combination of oil palm Empty fruit bunches (EFB) fibre and jute fibre as reinforcement, epoxy as polymer matrix. This study intended to investigate the effect of jute fiber hybridization and different layering pattern on the physical properties of oil palm EFB-Epoxy composites. Water absorption and thickness swelling test reveal that hybrid composite shows a moderate water absorption which is 11.20% for hybrid EFB/Jute/EFB composite and 6.08% for hybrid Jute/EFB/Jute composite. The thickness swelling and water absorption of the hybrid composites slightly increased as the layering pattern of hybrid composites changed. Hybrid composites are more water resistance and dimensional stable compare to the pure EFB composites. This is attributed to the more hydrophilic nature of EFB composites. Hybridization of oil palm EFB composites with jute fibres can improve the dimensional stability and density of pure EFB and Jute fibre reinforced composites has higher density of 1.2 g/cm³ compared to all other composites.     

Sisal/Carbon Fibre Reinforced Hybrid Composites: Tensile, Flexural and Chemical Resistance Properties

The variation of mechanical properties such as tensile and flexural properties of randomly oriented unsaturated polyester based sisal/carbon fibre reinforced hybrid composites with different fibre weight ratios have been studied. The chemical resistance test of these hybrid composites to various solvents, acids and alkalies were studied. The effect of NaOH treatment of sisal fibres on the tensile, flexural and chemical resistance properties of these sisal/carbon hybrid composites has also been studied. The hybrid composites showed an increase in tensile and flexural properties with increase in the carbon fibre loading. The tensile properties and flexural properties of these hybrid composites have been found to be higher than that of the matrix. Significant improvement in tensile properties and flexural properties of the sisal/carbon hybrid composites has been observed by alkali treatment. The chemical resistance test results showed that these untreated and alkali treated hybrid composites are résistance to all chemicals except carbon tetra chloride. Hand lay-up technique was used for making the composites and tests are carried out by using ASTM methods.     

Influences of Magnesium <Emphasis Type="Italic">tri-</Emphasis>Silicate on the Physical,Mechanical, and Degradable Properties of Ultraviolet (UV) Radiation Cured Plain Board Surface

A series of formulations were prepared with different percentages of oligomer, epoxy diacrylate (EA-1020 ), monomer, 1,6 Hexane diol diacrylate,(HDDA) and different percentages of filler (Magnesium tri-silicate, Mg₂Si₃O₈). Irgacure 369 [2-Benzyl-2-dimethyl-amine-1 (4-morpholinophenyl) butanone-1] was used in the formulations as photoinitiator. Ultraviolet (UV) cured thin polymer films were prepared from these formulating solutions on clean glass plates. Pendulum hardness (PH), gel content and macro scratch hardness (MSH) of the UV cured films were studied. One percent Mg₂Si₃O₈ containing formulation showed the premium properties. The substrates (plain board) were coated by these formulating solutions and cured under the same UV lamp at different intensities of radiation. Various properties of the coated surface such as PH, gloss, adhesion, abrasion and MSH were investigated. The base coat containing 1% Mg₂Si₃O₈ and top coat containing 48% HDDA produced the best performance among all the formulations inspected. The degradable properties in different weathering conditions on PH, gloss, adhesion, abrasion and MSH were measured. The surface cured with the optimized formulation (E) again yielded the minimum loss of the properties.     

Source identification, contamination status and health risk assessment of heavy metals from road dusts in Dhaka, Bangladesh

In this study, concentrations of Cr, Mn, Ni, Cu, Zn, Cd and Pb were determined in road dusts collected from different locations in Dhaka to assess source, contamination status and health risk. Energy-dispersive X-ray fluorescence spectroscopy and energy-dispersive X-ray spectroscopy were used to determine Cr, Mn, Ni, Cu, Zn, Cd and Pb and their mean concentrations were 162.27 ± 29.46, 721.18 ± 180.14, 35.65 ± 12.55, 104.56 ± 128.33, 515.32 ± 321.90, BDL, and 342.82 ± 591.20 mg/kg, respectively. Among the heavy metals, highest concentrations of Cu, Zn and Pb were found at urban sites-7 (municipal waste dumping) and 8 (medical waste incineration). Highest concentration of Cr followed by Cu and Zn was found at site-5 (Tejgaon, urban). Principal component analysis revealed that anthropogenic activities are the potential sources for Cr, Ni, Cu, Zn and Pb while earth crust for Mn. Pollution index and pollution load index results suggested that all the sites were contaminated and/or degraded by Cr, Cu, Zn and Pb except sites-9 (urban), 10 (sub-urban), 11 (rural) while sites-7 and 8 (urban) were extremely degraded. For noncarcinogenic health risk, hazard quotient values for dermal were higher compared to that of inhalation/ingestion. Though hazard index values were less than 1 at all the sites, these were at least one order of magnitude higher for children group than that of adult group, thus the children group may face more noncarcinogenic health risk at sites-7 and 8. Values of incremental lifetime cancer risk were from 10⁻⁹ to 10⁻¹¹ showed no carcinogenic health risk by road dusts contaminated with the heavy metals.     

A global perspective on the biology,impact and management of Chenopodium album and Chenopodium murale: two troublesome agricultural and environmental weeds

Environmental Science and Pollution Research - Chenopodium album and C. murale are cosmopolitan, annual weed species of notable economic importance. Their unique biological features, including high...     

The Effect of Silane Treated Fibre Loading on Mechanical Properties of Pineapple Leaf/Kenaf Fibre Filler Phenolic Composites

The aim of the present study is to investigate mechanical and morphological properties of pineapple leaf fibres (PALF) reinforced phenolic composites and its comparison with kenaf fibre (KF)/phenolic composites. Mechanical properties (tensile, flexural and impact) of untreated and treated PALF phenolic composites at different fibre loading were investigated. Tensile, flexural and impact properties of PALF and kenaf/phenolic composites were analyzed as per ASTM standard. Morphological analysis of tensile fracture samples of composites was carried out by scanning electron microscopy. Obtained results indicated that treated PALF/phenolic composites at 50% PALF loading exhibited better tensile, flexural and impact properties as compared to other untreated PALF/phenolic composites. Treated kenaf/phenolic composites at 50% fibre loading showed better tensile, flexural and impact properties than untreated kenaf/phenolic composite. It is concluded that treated 50% fibre loading kenaf and PALF/phenolic composites showed better mechanical properties than untreated kenaf and PALF/phenolic composites due to good fibre/matrix interfacial bonding. Results obtained in this study will be used for the further study on hybridization of PALF and KF based phenolic composites.     

Nanocarrier-mediated co-delivery systems for lung cancer therapy: recent developments and prospects

Environmental Chemistry Letters - Research has recently focused on combinational therapy using nanocarriers to overcome the obstacles associated with conventional therapy of lung cancer. The...