Preparation of black lyophilic ink using the carbon soot emitted by vehicles

Environmental Science and Pollution Research - The carbon soot is formed as a consequence of incomplete combustion of hydrocarbons and organic matter. It causes respiratory diseases like lung...     

Studies on the use of power ultrasound in solid–liquid myrobalan extraction process

Focus on eco-friendly processing techniques makes vegetable tanning a viable option in leather processing and establishes the subsequent need for the more efficient methods of extraction in tannin manufacture. Application of ultrasound has been tried in the extraction of tannins from myrobalan nuts in order to improve the extraction efficiency, to perform the extraction under milder process conditions and to reduce the process time. The influence of process parameters such as ultrasonic output power, time and temperature has been studied. Scale-up trials and the use of ultrasound in pulse mode have also been attempted. The results show that a three- to fivefold improvement is possible with ultrasonic output from 20 to 100 W. Extraction efficiency has been calculated from the maximum extractable materials from myrobalan nuts. Extraction efficiency is found to be 90% for ultrasound, 100 W without external heating as compared to 77% for control process at 70 °C for 4 h. Therefore, ultrasound could be employed even dispensing with provision for temperature controls. The use of ultrasound in pulse mode offered 70% extraction efficiency of continuous mode. Scale-up trials indicate that there exists an optimum ultrasonic output power depending on the amount of nuts used, to achieve better extraction efficiency. The effectiveness of ultrasonically extracted tannin solution has also been tested in the tanning process for its applicability. The degree of tanning efficacy has been assessed by shrinkage temperature measurement. The results indicate that ultrasonically extracted tannin solution is suitable for tanning process. Therefore, application of ultrasound in tannin extract manufacture is a viable option with added advantages.     

Assessment of nitrogen losses through nitrous oxide from abattoir wastewater-irrigated soils

The land disposal of waste and wastewater is a major source of N₂O emission. This is due to the presence of high concentrations of nitrogen (N) and carbon in the waste. Abattoir wastewater contains 186 mg/L of N and 30.4 mg/L of P. The equivalent of 3 kg of abattoir wastewater-irrigated soil was sieved and taken in a 4-L plastic container. Abattoir wastewater was used for irrigating the plants at the rates of 50 and 100 % field capacity (FC). Four crop species were used with no crop serving as a control. Nitrous oxide emission was monitored using a closed chamber technique. The chamber was placed inside the plastic container, and N₂O emission was measured for 7 days after the planting. A syringe and pre-evacuated vial were used for collecting the gas samples; a fresh and clean syringe was used each time to avoid cross-contamination. The collected gas samples were injected into a gas chromatography device immediately after each sampling to analyse the concentration of N₂O from different treatments. The overall N₂O emission was compared for all the crops under two different abattoir wastewater treatment rates (50 and 100 % FC). Under 100 % FC (wastewater irrigation), among the four species grown in the abattoir wastewater-irrigated soil, Medicago sativa (23 mg/pot), Sinapis alba (21 mg/pot), Zea mays (20 mg/pot) and Helianthus annuus (20 mg/pot) showed higher N₂O emission compared to the 50 % treatments—M. sativa (17 mg/pot), S. alba (17 mg/pot), Z. mays (18 mg/pot) and H. annuus (18 mg/pot). Similarly, pots with plants have shown 15 % less emission than the pots without plants. Similar trends of N₂O emission flux were observed between the irrigation period (4-week period) for 50 % FC and 100 % FC. Under the 100 % FC loading rate treatments, the highest N₂O emission was in the following order: week 1 > week 4 > week 3 > week 2. On the other hand, under the 50 % FC loading rate treatments, the highest N₂O emission was recorded in the first few weeks and in the following order: week 1 > week 2 > week 3 > week > 4. Since N₂O is a greenhouse gas with high global warming potential, its emission from wastewater irrigation is likely to impact global climate change. Therefore, it is important to examine the effects of abattoir wastewater irrigation on soil for N₂O emission potential.

     

Performance evaluation of reverse logistics enterprise – an agent-based simulation approach

Reverse logistics (RL) has been applied in many industries and sectors since its conception. Unlike forward logistics, retracing consumer goods from the point of consumption to the point of inception is not a well-studied process. It involves many uncertainties such as time, quality and quantity of returns. The returned products can be remanufactured, have parts harvested, or be disposed safely. It is important to implement these activities in a cost-effective manner. The aim of this research is to measure the performance of the RL enterprise with the help of an agent-based simulation model. The major entities in the RL network are considered as Agents that can act independently. There are several different agents: collector agent, sorting-cum-reuse agent, remanufacturing agent, recycler agent, supplier agent and distributor agent. The individual performances of the agents are measured and recommendations are given to improve their performance, leading to the enhancement of the total performance of the RL enterprise. The approach is applied to a case study involving cell phone remanufacturing.     

Synthesis of low-cost bentonite/Duranta erecta’s fruit powder imbedded alginate beads and its application in surfactant removal

Environmental Science and Pollution Research - High industrialization and improved medical facilities are deteriorating aquatic bodies through untreated effluents. This study is aimed to design and...     

Investigation of performance enhancement of solar still incorporated with Gallus gallus domesticus cascara as sensible heat storage material

In this research work, the conventional single slope still (CSS) with egg shells of breed Gallus gallus domesticus cascara as sensible heat storage (SHS) material are studied experimentally to enhance the yield. In this experimental investigation, the proposed single slope still (PSS) with SHS material was made in comparison with the CSS to evaluate the productivity of fresh water under the same ambient conditions. Comparatively, this PSS has higher thermal conductivity than the CSS. The yield obtained from the PSS is 2.46 L/m², while the yield from the CSS is 2.07 L/m². The average rate at which the rise of output fresh water obtained from the PSS is 18% more than the fresh water output obtained from the CSS. The daily energy efficiency of the PSS is 26.07%, and for the CSS, it is only 22.25%. The daily exergy efficiency of the PSS is 2.36%, and for the CSS, it is only 1.67%. Since using the egg shell will employ as organic waste management and modification in this still is economical, less initial, and maintenance cost.

     

Simulations and experiments in punching spring-steel devices with sub-millimeter features

This work demonstrates the feasibility of meso-scale (100 μm to mm) punching of multiple holes of intricate shapes in metals. Analytical modeling, finite element (FE) simulation, and experimentation are used in this work. Two-dimensional FE simulations in ABAQUS were done with an assumed material modeling and plane-strain condition. A known analytical model was used and compared with the ABAQUS simulation results to understand the effects of clearance between the punch and the die. FE simulation in ABAQUS was done for different clearances and corner radii of the punch, die, and holder. To complement modeling with real experiments and for the purpose of comparison, a set of punches and dies were made to punch out a miniature spring-steel gripper. Comparison of compliant grippers made by wire-cut electro discharge machining (EDM) and punching shows that realizing sharp interior and re-entrant corners by punching is not easy to achieve. However, the promise of realizing meso-scale parts with complicated shapes through punching is demonstrated in this work; and further work is identified and some strategies are suggested for improvement. The main contribution of this paper is in adapting the well-established punching and blanking operations to the meso-scale as a viable alternative to making miniature devices currently dominated by lithography-based techniques.     

Constitutive model for municipal solid waste incorporating mechanical creep and biodegradation-induced compression

A constitutive model is proposed to describe the stress–strain behavior of municipal solid waste (MSW) under loading using the critical state soil mechanics framework. The modified cam clay model is extended to incorporate the effects of mechanical creep and time dependent biodegradation to calculate total compression under loading. Model parameters are evaluated based on one-dimensional compression and triaxial consolidated undrained test series conducted on three types of MSW: (a) fresh MSW obtained from working phase of a landfill, (b) landfilled waste retrieved from a landfill after 1.5 years of degradation, and (c) synthetic MSW with controlled composition. The model captures the stress–strain and pore water pressure response of these three types of MSW adequately. The model is useful for assessing the deformation and stability of landfills and any post-closure development structures located on landfills.     

Low NOx,High Efficiency Multistaged Burner: Fuel Oil Results

A multistaged combustion burner designed for in-furnace NO_x control and high combustion efficiency is being evaluated for high nitrogen content fuel and waste incineration application in a 0.6 MW package boiler simulator. A low NO_x precombustion chamber burner has been reduced in size by approximately a factor of two (from 600 to 250 ms first-stage residence time) and coupled with (1) air staging, resulting in a three-stage configuration, and (2) natural gas fuel staging, yielding up to four stolchlometric zones. Natural gas, doped with ammonia to yield a 5.8 percent fuel nitrogen content, and distillate fuel oil, doped with pyridine to yield a 2 percent fuel nitrogen content, were used to simulate high nitrogen content fuel/waste mixtures. The multistaged burner reduced NO emissions by 85 percent from emission levels from a conventional unstaged burner mounted on a commercial package bollerTA minimum NO emission level of 110 ppm was achieved in the fuel oil tests, from a level of 765 ppm for conventional firing. This is compared with a 160 ppm minimum NO level achieved in gaseous fuel tests, from an uncontrolled level of 1000 ppm. Boiler fuel staging, or reburnlng, appears to be superior to air staging for high combustion efficiency due to its minimal fuel-rich core and second flame front in the boiler.