Measuring water resource use efficiency of the Dong Nai River Basin (Vietnam): an application of the two-stage data envelopment analysis (DEA)

Environment, Development and Sustainability - The recent growth of agriculture, industry and urban areas in Vietnam requires a large amount of water consumption as a production factor. This paper...     

Sorbent-based devices for the removal of spilled oil from water: a review

Environmental Science and Pollution Research - Always, oil spills do cause serious and dire consequences for the environment, nature, and society that it consumes much time and socio-economic...     

BTEX pollution caused by motorcycles in the megacity of HoChiMinh

Monitoring of benzene, toluene and xylenes (BTEX) was conducted along with traffic counts at 17 roadside sites in urban areas of HoChiMinh. Toluene was the most abundant substance, followed by p,m-xylenes, benzene, o-xylene and ethylbenzene. The maximum observed hour-average benzene concentration was 254 μg/m3 . Motorcycles contributed to 91% of the traffic fleet. High correlations among BTEX species, between BTEX concentrations and the volume of on-road motorcycles, and between inter-species ratios in air and in gasoline indicate the motorcycle-exhaust origin of BTEX species. Daily concentrations of benzene, toluene, ethylbenzene, p,m-xylenes and o-xylene were 56, 121, 21, 64 and 23 μg/m 3 , respectively. p,m-xylenes possess the highest ozone formation potential among the BTEX family.     

Characterization of hard- and softwood biochars pyrolyzed at high temperature

A wide range of waste biomass/waste wood feedstocks abundantly available at mine sites provide the opportunity to produce biochars for cost-effective improvement of mine tailings and contaminated land at metal mines. In the present study, soft- and hardwood biochars derived from pine and jarrah woods at high temperature (700 °C) were characterized for their physiochemical properties including chemical components, electrical conductivity, pH, zeta potential, cation-exchange capacity (CEC), alkalinity, BET surface area and surface morphology. Evaluating and comparing these characteristics with available data from the literature have affirmed the strong dictation of precursor type on the physiochemical properties of the biochars. The pine and jarrah wood feedstocks are mainly different in their proportions of cellulose, hemicellulose and lignin, resulting in biochars with heterogeneous physiochemical properties. The hardwood jarrah biochar exhibits much higher microporosity, alkalinity and electrostatic capacity than the softwood pine. Correlation analysis and principal component analysis also show a good correlation between CEC–BET–alkalinity, and alkalinity–ash content. These comprehensive characterization and analysis results on biochars’ properties from feedstocks of hardwood (from forest land clearance at mine construction) and waste pine wood (from mining operations) will provide a good guide for tailoring biochar functionalities for remediating metal mine tailings. The relatively inert high-temperature biochars can be stored for a long term at mine closure after decades of operations.     

A COMPARISON OF STATISTICAL TESTS ON THE EXTREME-VALUE TYPE-1 DISTRIBUTION1

ABSTRACT: The effects of the selections of plotting position formulae and class division schemes on goodness of fit tests are investigated for the extreme-value type-1 distribution using annual flood and annual maximum daily rainfall data. It was found that the plotting position formulae have a minor influence on the tests which involve their use, while the class division schemes may have a pronounced effect on the X²-test. The study also recommended the maximum likelihood method for fitting purposes and a new test which is independent of the afore-mentioned selections for judging the goodness of fit.     

COMPARISON OF TWO AUTOREGRESSIVE MODELS FOR MONTHLY STREAM FLOW GENERATION1

ABSTRACT: Two autoregressive models for monthly stream flow generation are compared based on the reproduction of the historical record in terms of several important statistics such as the mean, standard deviation, skewness coefficient, correlation coefficient, and the reservoir storage components. In the comparison, both theoretical considerations and practical applications are employed to evaluate the performance of each model.     

Normality of Hydrological Data1

ABSTRACT: Assessment of normality of hydrological data has been based upon subjective judgments. This paper aims to provide an objective method for such an assessment by introducing three computationally simple statistical tests. Application to some stream flow data indicates that (1) for annual values, at least one of the three sequences- original, square root, and logarithmic - can be considered to be normally distributed; and (2) most monthly stream flows are skew and neither the square root nor the logarithmic transformation is able to render their sequences in all the 12 months normal.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.