Assessment of long-term wastewater irrigation impacts on the soil geochemical properties and the bioaccumulation of heavy metals to the agricultural products

An extensive field survey was employed for assessing the impacts of long-term wastewater irrigation of forage crops and orange orchards in three suburban agricultural areas in Cyprus (areas I, II, and III), as compared to rainfed agriculture, on the soil geochemical properties and the bioaccumulation of heavy metals (Zn, Ni, Mn, Cu, Co) to the agricultural products. Both ryegrass fields and orange orchards in areas I and II were continuously wastewater irrigated for 10 years, whereas clover fields in area III for 0.5, 4, and 8 years. The results revealed that wastewater reuse for irrigation caused a slight increase in soil salinity and Cl^? content in areas I and II, and a remarkable increase, having strong correlation with the period in which wastewater irrigation was practiced, in area III. Soil salinization in area III was due to the high electrical conductivity (EC) of the wastewater applied for irrigation, attributed to the influx of seawater to the sewage collection network in area III. In addition, the wastewater irrigation practice resulted in a slight decrease of the soil pH values in area III, while a subtle impact was identified regarding the CaCO₃, Fe, and heavy metal content in the three areas surveyed. The heavy metal content quantified in the forage plants’ above-ground parts was below the critical levels of phytotoxicity and the maximum acceptable concentration in dairy feed, whereas heavy metals quantified in orange fruit pulp were below the maximum permissible levels (MPLs). Heavy metal phytoavailability was confined due to soil properties (high pH and clay content), as evidenced by the calculated low transfer factor (TF).     

Solid waste characterization,quantification and management practices in developing countries. A case study: Nablus district – Palestine

Solid waste management (SWM) is one of the most challenging issues faced by developing countries that suffer from serious pollution problems caused by the generation of large waste quantities. This paper presents the case study of SWM in the Nablus district – Palestine. Surveys for household residents' and SWM program operators, field investigations, on-site waste measurements and characterizations were conducted. Per capita waste generation rates varied between different localities although trends were similar. Overall, the majority of waste was organic (65.1% by weight), suggesting a strong resource recovery potential in terms of animal feed or compost. Recyclable waste (plastic, paper and card) made up 16.7% by weight the waste composition suggesting an incentive to introduce source separation. Household attitudes complemented the waste characterization study, revealing the main problems faced. SWM operators quoted on the current status, highlighting problems with disposing in unsanitary landfills, ineffective solid waste fees system, increasing solid waste quantities and lacking equipment and experienced personnel. To enhance sustainable SWM, public awareness, funding, expertise, equipment and facilities and other provisions currently lacking or inappropriate must be provided.     

A study on the landfill leachate and its impact on the groundwater quality of the greater area

Characterisation of the leachate originating from the Ano Liosia landfill (situated in Attica region, Greece) as well as assessment on the quality of the local aquifer were carried out. The experimental results showed that most of the parameters examined in the leachate samples such as colour, conductivity, TS, COD, NH₃–N, PO₄–P, SO₄ ^2–, Cl^–, K⁺, Fe and Pb were found in high levels. The organic load was quite high since the COD concentrations were in the range of 3250–6125mgL^–1. In addition, the low BOD/COD ratio (0.096–0.195), confirmed that the majority of this organic matter is not easily biodegradable. The groundwater near the landfill site was characterised as not potable and not suitable for irrigation water, since most of the physical and chemical parameters examined – such as colour, conductivity, DS, hardness, Cl^–, NH₃–N, COD, K⁺, Na⁺, Ca²⁺, Fe, Ni and Pb exceeded the permissible limits given by EE, EPA and the Greek Ministry of Agriculture. Furthermore, this study presents the application of the hydrologic evaluation of landfill performance (HELP) model for the determination of the yearly leakage from the base of the landfill after the final capping.     

Implementation of the European IPPC Directive—BAT guidelines for the cement industry in Cyprus

The European Integrated Pollution Prevention and Control (IPPC) Directive 96/61/EC aims to introduce a European-wide system of integrated prevention and control of pollution in order to secure a high level of protection to the environment as a whole. It places obligations on the Member States (MS) to introduce controls that ensure operators comply with the Directive. In this framework, as a part of the implementation process leading to formal accession of Cyprus to the European Union, the National Technical University of Athens has examined all documents related to the Best Available Techniques (BATs) published by Institutes and Organisations, such as the Institute for Prospective Technological Studies in Spain, the Environmental Protection Agency in Ireland, the World Bank Group and the Ministry for the Environment, Planning and Public Works in Greece. A series of guidelines were developed for the application of BATs for 14 categories of the Cypriot industry that fall into the IPPC Directive. The concept of BATs plays a central role in the Directive because it provides a basis for setting Emission Limit Values (ELVs) as well as the principal benchmark for determining the obligations of industrial operators in respect of pollution prevention and control. This paper presents the guidelines for cement manufacture in Cyprus.     

Rapid screening procedure to optimise the anaerobic codigestion of industrial biowastes and agricultural livestock wastes in Cyprus

Small-scale experimental investigations were undertaken on the anaerobic digestion (AD) and codigestion of livestock waste and industrial biowastes. A simple procedure was developed to rapidly determine the suitability of wastes for digestion. The experiment was split into two phases; initially, the seed (digested brewery waste) was replaced by the test waste over a period of 5 days. During the second phase, the test waste was incubated and monitored for methanogenesis. Dairy cattle slurry was the most efficient co-substrate which, when codigested with pig slurry in an equal ratio achieved volatile solids destruction of 32%, CH(4) production rate of 97.4 ml d(-1), maximum CH(4) content of 61.6% and total gas yield of 2229 ml after 529 h. High fat content wastes were unsuitable for AD due to low pH value and because the dominant microbial reaction was fermentation. Codigestion was investigated to overcome any inhibitions; however, dairy cattle slurry, abattoir wastewater and NaOH additions did not lead to methanogenesis. Treating these wastes by AD is feasible but without CH(4) production.     

An alternative method for the treatment of waste produced at a dye and a metal-plating industry using natural and/or waste materials.

The aim of this study was to develop cost-effective, appropriate solidification technologies for treating hazardous industrial wastes that are currently disposed of in ways that may threaten the quality of local groundwater. One major objective was to use materials other than cement, and preferably materials that are themselves wastes, as the solidification additives, namely using wastes to treat wastes or locally available natural material. This research examines the cement-based and lime-based stabilization/solidification (S/S) techniques applied for waste generated at a metal-plating industry and a dye industry. For the lime-based S/S process the following binder mixtures were used: cement kiln dust/ lime, bentonite/lime and gypsum/lime. For the cement-based S/S process three binder mixtures were used: cement kiln dust/cement, bentonite/cement and gypsum/cement. The leachability of the wastes was evaluated using the toxicity characteristic leaching procedure. The applicability and optimum weight ratio of the binder mixtures were estimated using the unconfined compressive strength test. The optimum ratio mixtures were mixed with waste samples in different ratios and cured for 28 days in order to find the S/S products with the highest strength and lowest leachability at the same time. The results of this work showed that the cement-and lime-based S/S process, using cement kiln dust and bentonite as additives can be effectively used in order to treat industrial waste.     

Integrated environmental monitoring and simulation system for use as a management decision support tool in urban areas

Leachates are generated as a result of water or other liquid passing through waste at a landfill site. These contaminated liquids originate from a number of sources, including the water produced during the decomposition of the waste as well as rain-fall which penetrates the waste and dissolves the material with which it comes into contact. The penetration of the rain-water depends on the nature of the landfill (e.g. surface characteristics, type and quantity of vegetation, gradient of layers, etc). The uncontrolled infiltration of leachate into the vadose (unsaturated) zone and finally into the saturated zone (groundwater) is considered to be the most serious environmental impact of a landfill. In the present paper the water flow and the pollutant transport characteristics of the Ano Liosia Landfill site in Athens (Greece) were simulated by creating a model of groundwater flows and contaminant transport. A methodology for the model is presented. The model was then integrated into the Ecosim system which is a prototype funded by the EU, (Directorate General XIII: Telematics and Environment). This is an integrated environmental monitoring and modeling system, which supports the management of environmental planning in urban areas.     

Removal of residual pharmaceuticals from aqueous systems by advanced oxidation processes

Over the past few years, pharmaceuticals are considered as an emerging environmental problem due to their continuous input and persistence to the aquatic ecosystem even at low concentrations. Advanced oxidation processes (AOPs) are technologies based on the intermediacy of hydroxyl and other radicals to oxidize recalcitrant, toxic and non-biodegradable compounds to various by-products and eventually to inert end-products. The environmental applications of AOPs are numerous, including water and wastewater treatment (i.e. removal of organic and inorganic pollutants and pathogens), air pollution abatement and soil remediation. AOPs are applied for the abatement of pollution caused by the presence of residual pharmaceuticals in waters for the last decade. In this light, this paper reviews and assesses the effectiveness of various AOPs for pharmaceutical removal from aqueous systems.