Enhancing the adsorption function of biochar by mechanochemical graphitization for organic pollutant removal

• Mechanochemical treatment reduced the calcination temperature for biochar synthesis. • Biochar is converted to graphite after mechanochemical treatment. • Biochar was reduced to nanoscale after mechanochemical treatment. Biochar (BC) has been extensively studied as adsorbent for the treatment of water pollution. Despite the distinct advantages, the high calcination temperature and low adsorption capacity of pristine BC limit its practical applications. Most of the former studies focused on the structure and/or surface modification to improve the adsorption capacity of BC. However, the harsh experiment conditions involved in the biochar modification limited the application in industrial level. Herein, we introduced mechanical treatment into BC preparation to reduce the calcination temperature and improve the adsorption capacity simultaneously. The results indicated that the calcination temperature was reduced and the adsorption capacity of the treated BC was improved after mechanochemical treatment. Characterization of the samples disclosed that BCs were graphitized with the particle size reduced to nanoscale after treatment. Adsorption tests indicated that the mechanochemically treated BCs showed much better removal performance of organic contaminants than that of pristine BCs. For instance, among four pristine BCs (BC600, BC700, BC800, and BC900), only BC900 has strong adsorption capacity for MB, while BC600 has low adsorption capacity (1.2 mg/g). By comparison, the adsorption capacity of MB increased greatly to 173.96 mg/g by BC600-500/1 (treated at 500 r/min for 1 hour). To optimize the mechanochemical treatment, the effects of rotation speed and agitation duration were also investigated.     

pH对铝盐絮凝剂形态分布与混凝除氟性能的影响

对比研究了AlC13和3种不同碱化度的聚合氯化铝(PACl)在不同pH与投量下除氟效果,并对不同形态铝盐除氟机理进行了初步探讨.结果表明,pH对絮凝剂水解后铝形态分布及其除氟效果有重要影响.pH 5 ～6时,Al3+和Al2、Al3等低聚态铝为AlCl3主要形态,且AlCl3更易水解生成可将溶解态氟转化为颗粒态氟的Al(OH)3,从而较PACl具有更佳除氟效果.pH ＞7时,PACl较AlCl3具有更佳除氟效果,且增大PACl碱化度可促进氟的去除,这主要是由于具有较高Al13含量的PACl更容易与电负性F-结合所致;且絮凝剂混凝除氟絮体ζ电位越高,越利于F-在絮体表面吸附.     

蒽醌修饰石墨毡电极预处理头孢合成废水

以钛涂钌电极为阳极、自制蒽醌修饰石墨毡电极为阴极,对头孢合成废水(COD=25 000~30 000 mg/L、ρ(NH3-N)=850~1 300 mg/L、色度为2 300~2 680度)进行了电化学氧化预处理,优化了电解条件,并对电化学体系的动力学和稳定性进行了分析。实验结果表明:蒽醌的存在可改善电化学氧化降解效果;在电解时间50 min、电流密度0.14 A/cm2、Na2SO4浓度0.1 mol/L、极板间距2 cm、初始废水p H 7.0的条件下,废水的COD、色度、NH3-N的去除率分别可达45.3%,66.9%,33.6%;BOD5/COD由处理前的0.27增至0.40,可生化性得到改善;COD、色度、NH3-N的电化学氧化降解过程均近似符合一级动力学方程;且该电化学体系的应用稳定性良好。     

基于关联性及趋势性分析的AVHRR NDVI及#br# MODIS NDVI数据产品比较

针对AVHRR NDVI和MODIS NDVI数据集中不同数据产品间的差异和区域适应性问题，利用2003~2013年重叠时间段MODIS Terra/Aqua的NDVI Collection 5(C5)和Collection 6(C6)产品以及AVHRR NDVI中的GIMMS NDVI3g产品，选择汉江流域典型区域进行数据对比分析。通过关联指数IOAs(Index of Association)来评价各数据在季节波动上的一致性；采用Mann Kendall检验分析各数据的长期趋势差异。结果表明，在季节性变化上，同一卫星不同版本产品之间的关联性相对较高。在年际变化上，GIMMS产品相对MODIS 产品，仅能检出部分NDVI变化趋势。在地表覆被异质性相对较高地区，GIMMS产品的长期变化趋势检出率较低。MODIS Terra的NDVI C5产品受传感器退化影响，表现出相对较高的减少趋势。 关键词： GIMMS NDVI；MODIS NDVI；Mann Kendall检验；趋势分析     

环境检测机构人员培训工作探讨

环境检测人员培训在整个生态文明建设中发挥着至关重要的作用,本文从培训计划、培训内容、培训方式、有效评价和记录归档五个方面探讨了环境检测机构人员培训工作流程,以确保机构行之有效地开展人员培训。     

浮游动物DNA宏条形码标志基因比较研究

DNA宏条形码技术作为一种新型生物监测方法,在未来生态环境监测中有巨大的应用潜力。目前,浮游动物DNA宏条形码监测仍在发展阶段,需要首先对其(采样方法、引物选择和数据分析等)进行标准化和调整,然后才能用于常规流域生态监测。其中,如何选择合适的PCR扩增引物是DNA宏条形码生物监测标准化的关键问题之一。本研究比较了COI、18SV9和16S通用引物在浮游动物DNA宏条形码监测中的差异,为初步建立规范化的浮游动物DNA宏条形码监测方法提供技术支撑。结果表明,16S引物对浮游动物具有更好的特异性,其产生的操作分类单元(operational taxonomic unit, OTU)有88.1%属于浮游动物。虽然18SV9引物具有更高的物种覆盖度,不仅能扩增出浮游动物,还能扩增出大量藻类和真菌,但其物种识别敏感性较差,不适合浮游动物物种水平多样性监测。COI引物的浮游动物物种特异性、物种覆盖度和物种识别敏感性都适中,检出的浮游动物物种数量高于18SV9引物和16S引物,更加适合浮游动物DNA宏条形码监测。     

Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.     

Microfiber pollution: an ongoing major environmental issue related to the sustainable development of textile and clothing industry

Environment, Development and Sustainability - Textiles release microfibers to the environment during production, use, and at end-of-life disposal. There is a potentially large and growing risk to...     

Study on the measurement and the changing trend of the energy use of China’s economic sectors: based on cross-region input-output model

Environmental Science and Pollution Research - The consumption of fossil energy is the major cause of environmental pollution. Effectively reducing the fossil energy use has important significance...     

FRP加固震损RC柱建模方法及骨架模型研究

为研究震损RC柱采用FRP(Fiber Reinforced Polymer,FRP)加固修复后的抗震性能,本文基于OpenSees仿真平台,根据震后RC柱的表观损伤状态提出FRP加固震损RC柱的有限元模型建立方法。对FRP加固震损RC柱进行5120种工况的Pushover分析,采用三折线荷载-位移骨架曲线,研究损伤状态对骨架曲线特征点参数的影响规律,并通过数据回归分析提出FRP加固震损RC柱的骨架曲线计算模型。分析结果表明:损伤会降低FRP加固RC柱的承载力及刚度,且降低程度随损伤指数的增大而增加,两者近似成抛物线关系;在DS-5损伤状态下,相比于FRP加固完好RC柱,FRP加固震损RC柱的屈服承载力P y、峰值承载力P c、弹性刚度K 1、弹塑性刚度K 2及下降段刚度K 3的均值下降17.9%、14.5%、41.8%、43.1%和19.9%;损伤对FRP加固RC柱弹性刚度和弹塑性刚度的降低程度明显高于屈服承载力和峰值承载力;文中提出的FRP加固震损RC柱骨架曲线计算模型具有较高精度。