An integrated multivariate statistical approach for the evaluation of spatial variations in groundwater quality near an unlined landfill

Environmental Science and Pollution Research - Groundwater is a major resource for water supply in Canada, and 43 of 68 Saskatchewan municipalities rely on groundwater or combined groundwater and...     

Fluoride removal and its impact on oral health in Sri Lanka's dry zone: Discussion and recommendation

Fifty percent of the dry zone areas in Sri Lanka have fluoride levels above 1 ppm. This paper discusses the ground conditions and recommends an appropriate range of fluoride in drinking water which can support preventive practices for improving the oral health of children 8-years old and younger. In efforts to address the Chronic Kidney Disease of Unknown etiology (CKDU), water treatment to reduce contaminant level in potable water has been implemented. Such treatment would also remove fluoride and has resulted in potable water with various fluoride levels, depending on concentrations in the raw water. While it is important to reduce fluoride levels, it is important to have appropriate residual levels for prevention of dental caries. It needs, however, to be noted fluoride in excess can cause dental fluorosis. In Sri Lanka's dry zone areas increasing prevalence of dental fluorosis with decreasing prevalence of dental caries has been noted. Consumption of tea and powdered milk could increase total intake of fluoride. Fluoridated toothpaste, when used properly, may, however, result in negligible intake of fluoride. Sri Lanka's hot tropical climate which results in substantial intake of fluids reinforces the need to consider reduction in water fluoride. Consideration of local studies and international standards indicate fluoride levels should be in the range of 0.225–0.500 ppm. In the range of 0.225–0.500 ppm, the prevalence of dental fluorosis and caries was only 14% and 8%, respectively, in an endemic district. When fluoride levels are above 0.500 ppm, the issue of dental fluorosis shall need to be addressed. When levels are below 0.225 ppm, oral health care services shall need to be directed at preventing dental caries.     

Materials,fuels, upgrading,economy, and life cycle assessment of the pyrolysis of algal and lignocellulosic biomass: a review

Climate change issues are calling for advanced methods to produce materials and fuels in a carbon–neutral and circular way. For instance, biomass pyrolysis has been intensely investigated during the last years. Here we review the pyrolysis of algal and lignocellulosic biomass with focus on pyrolysis products and mechanisms, oil upgrading, combining pyrolysis and anaerobic digestion, economy, and life cycle assessment. Products include oil, gas, and biochar. Upgrading techniques comprise hot vapor filtration, solvent addition, emulsification, esterification and transesterification, hydrotreatment, steam reforming, and the use of supercritical fluids. We examined the economic viability in terms of profitability, internal rate of return, return on investment, carbon removal service, product pricing, and net present value. We also reviewed 20 recent studies of life cycle assessment. We found that the pyrolysis method highly influenced product yield, ranging from 9.07 to 40.59% for oil, from 10.1 to 41.25% for biochar, and from 11.93 to 28.16% for syngas. Feedstock type, pyrolytic temperature, heating rate, and reaction retention time were the main factors controlling the distribution of pyrolysis products. Pyrolysis mechanisms include bond breaking, cracking, polymerization and re-polymerization, and fragmentation. Biochar from residual forestry could sequester 2.74 tons of carbon dioxide equivalent per ton biochar when applied to the soil and has thus the potential to remove 0.2–2.75 gigatons of atmospheric carbon dioxide annually. The generation of biochar and bio-oil from the pyrolysis process is estimated to be economically feasible.

     

Effect of a high strength chemical industry wastewater on microbial community dynamics and mesophilic methane generation

A high strength chemical industry wastewater was assessed for its impact on anaerobic microbial com- munity dynamics and consequently mesophilic methane generation. Cumulative methane production was 251 mL/g total chemical oxygen demand removed at standard temperature and pressure at the end of 30 days experimental period with a highest recorded methane percentage of 80.6% of total biogas volume. Volatile fatty acids （VFAs） analysis revealed that acetic acid was the major intermediate VFAs produced with propionic acid accumulating over the experimental period. Quantitative analysis of microbial communities in the test and control groups with quantitative real time polymerase chain reaction highlighted that in the test group, Eubacteria （96.3%） was dominant in comparison with methanogens （3.7%）. The latter were dominated by Methanomicrobiales and Methanobacteriales while in test groups increased over the experimental period, reaching a maximum on day 30. Denaturing gradient gel electrophoresis profile was performed, targeting the 16S rRNA gene of Eubacteria and Archaea, with the DNA samples extracted at 3 different time points from the test groups. A phylogenetic tree was constructed for the sequences using the neighborhood joining method. The analysis revealed that the presence of organisms resembling Syntrophomonadaceae could have contributed to increased production of acetic and propionic acid intermediates while decrease of organisms resembling Pelotomaculum sp. could have most likely contributed to accumulation of propionic acid. This study suggested that the degradation of organic components within the high strength industrial wastewater is closely linked with the activity of certain niche microbial communities within eubacteria and methanogens.     

Alternative carbon dioxide modelling approaches accounting for high residual gases in LandGEM

High Canadian waste disposal rates necessitate landfill gas monitoring and accurate forecasting. CO₂ estimates in LandGEM version 3.02 currently rest on the assumptions that CO₂ is a function of CH₄, where the two gases make up nearly 100% of landfill gas content, leading to overestimated CO₂ collection estimates. A total of 25 cases (five formulas, five approaches) compared annual CO₂ collection at four western Canadian landfills. Despite common use in literature, the 1:1 ratio of CH₄ to CO₂ was not recommended to forecast landfill gas collection in cold climates. The existing modelling approach significantly overestimated CO₂ production in three of four sites, resulting in the highest residual sum of squares. Optimization resulted in the most accurate results for all formulas and approaches, which had the greatest reduction in residual sums of squares (RSS) over the default approach (60.1 to 97.7%). The 1.4 Ratio approach for L _o:L _o-CO2 yielded the second most accurate results for CO₂ flow (mean RSS reduction of 50.2% for all sites and subsection models). The annual k-modified LandGEM calculated k’s via two empirical formulas (based on precipitation) and yielded the lowest accuracy in 12 of 20 approaches. Unlike other studies, strong relationships between optimized annual k’s and precipitation were not observed.

     

Use of whole-body and subcellular Cu residues of Lumbriculus variegatus to predict waterborne Cu toxicity to both L. variegatus and Chironomus riparius in fresh water

We tested the use of whole-body and subcellular Cu residues (biologically-active (BAM) and inactive compartments (BIM)), of the oligochaete Lumbriculus variegatus to predict Cu toxicity in fresh water. The critical whole-body residue associated with 50% mortality (CBR₅₀) was constant (38.2-55.6 μg g⁻¹ fresh wt.) across water hardness (38-117 mg L⁻¹ as CaCO₃) and exposure times during the chronic exposure. The critical subcellular residue (CSR₅₀) in metal-rich granules (part of BIM) associated with 50% mortality was approximately 5 μg g⁻¹ fresh wt., indicating that Cu bioavailability is correlated with toxicity:subcellular residue is a better predictor of Cu toxicity than whole-body residue. There was a strong correlation between the whole-body residue of L. variegatus (biomonitor) and survival of Chironomus riparius (relatively sensitive species) in a hard water Cu co-exposure. The CBR₅₀ in L. variegatus for predicting mortality of C. riparius was 29.1-45.7 μg g⁻¹ fresh wt., which was consistent within the experimental period; therefore use of Cu residue in an accumulator species to predict bioavailability of Cu to a sensitive species is a promising approach.     

Origin and distribution of trace elements in high-elevation precipitation in southern China

Introduction

During a 2009 investigation of the transport and deposition of trace elements in southern China, 37 event-based precipitation samples were collected at an observatory on Mount Heng, China (1,269?m asl).

Methods

Concentrations of trace elements were analyzed using inductively coupled plasma?Cmass spectrometry and the wet deposition fluxes were established. A combination of techniques including enrichment factor analysis, principal component analysis, and back trajectory models were used to identify pollutant sources.

Results

Trace element concentrations at Mount Heng were among the highest with respect to measured values reported elsewhere. All elements were of non-marine origin. The elements Pb, As, Cu, Se, and Cd were anthropogenic, while Fe, Cr, V, Ba, Mn, and Ni were of mixed crustal/anthropogenic origin. The crustal and anthropogenic contributions of trace elements were 12.8 % (0.9?~?17.4 %) and 87.2 % (82.6?~?99.1 %), with the maximum crustal fraction being 17.4 % for Fe. Coal combustion, soil and road dust, metallurgical processes, and industrial activities contributed to the element composition.

Conclusions

Summit precipitation events were primarily distant in origin. Medium- to long-range transport of trace elements from the Yangtze River Delta and northern China played an important role in wet deposition at Mount Heng, while air masses from south or southeast of the station were generally low in trace element concentrations.     

Risk measures constituting a risk metrics which enables improved decision making: Value-at-Risk

In this work, a novel approach is proposed for expressing the risks of process plants consisting of a large number of scenarios, in the form of a risk metrics of leading indicators to prevent potential high profile industry accidents. The methodology includes: 1) risk estimation of a portfolio by CPQRA (or QRA), 2) monetization of the tangible risks with the inclusion of the lost time of production, 3) estimation of the maximum portfolio loss using Value-at-Risk approach, 4) inclusion of intangible risks using FN-curve and, 5) generation of F$-curve of tangible risks. The proposed methodology can particularly help in understanding the stakes at risk by performing the overall cost-benefit analysis, for identifying the most risky scenarios and identifying critical equipments to enable better risk-informed decision making in order to adopt appropriate risk mitigation measures. This work establishes the groundwork for developing measures for understanding and comparing the large number of risk values derived from QRA studies for large portfolios. It will aid in less subjective decision making as it enables the decision maker to choose the most preferred portfolio option among alternatives. Decisions made with the accurate understanding of the consequences of risks can significantly reduce potential work-related fatalities, property losses and save millions of dollars.