ASSESSING FLOOD MITIGATION ALTERNATIVES IN SHIJR AREA IN METROPOLITAN TAIPEI1

The Keelung River Basin in northern Taiwan lies immediately upstream of the Taipei metropolitan area. The Shijr area is in the lower basin and is subject to frequent flooding. This work applies micromanagement and source control, including widely distributed infiltration and detention/ retention runoff retarding measures, in the Wudu watershed above Shijr. A method is also developed that combines a genetic algorithm and a rainfall runoff model to optimize the spatial distribution of runoff retarding facilities. Downstream of Wudu in the Shijr area, five dredging schemes are considered. If 10‐year flood flows cannot be confined in the channel, then a levee embankment that corresponds to the respective runoff retarding scheme will be required. The minimum total cost is considered in the rule to select from the regional flood mitigation alternatives. The results of this study reveal that runoff retarding facilities installed in the upper and middle parts of the watershed are most effective in reducing the flood peak. Moreover, as the cost of acquiring land for the levee embankment increases, installing runoff retarding measures in the upper portion of the watershed becomes more economical.     

Exposure Programme on Atmospheric Corrosion Effects of Acidifying Pollutants in Tropical and Subtropical Climates

Many national exposure programmes have been performed in tropical and subtropical climates during the last 50 years. However, ambitious programmes involving more than a few countries are scarce. In this paper a recently formed network of test sites is described involving 12 test sites in Asia (India, Vietnam, Thailand, Malaysia and China including Hong Kong) and four test sites in Africa (South Africa, Zambia and Zimbabwe). This effort is part of the 2001–2004 Swedish International Development Agency (SIDA) funded Programme on Regional Air Pollution in Developing Countries (RAPIDC). Corrosion attack after one (2002–2003) year of exposure (carbon steel, zinc, copper, limestone and paint coated steel) are presented together with environmental data (SO₂, NO₂, HNO₃, O₃, particles, amount and pH of precipitation, temperature and relative humidity) for all the test sites. The obtained corrosion values are substantially higher than expected for limestone, higher than expected for carbon steel and lower than expected for zinc compared to values calculated using the best available dose–response functions.     

Chemical speciation,transport and contribution of biomass burning smoke to ambient aerosol in Guangzhou,a mega city of China

Intensive measurements of aerosol (PM₁₀) and associated water-soluble ionic and carbonaceous species were conducted in Guangzhou, a mega city of China, during summer 2006. Elevated levels of most chemical species were observed especially at nighttime during two episodes, characterized by dramatic build-up of the biomass burning tracers levoglucosan and non-sea-salt potassium, when the prevailing wind direction had changed due to two approaching tropical cyclones. High-resolution air mass back trajectories based on the MM5 model revealed that air masses with high concentrations of levoglucosan (43–473 ng m^?3) and non-sea-salt potassium (0.83–3.2 μg m^?3) had passed over rural regions of the Pearl River Delta and Guangdong Province, where agricultural activities and field burning of crop residues are common practices. The relative contributions of biomass burning smoke to organic carbon in PM₁₀ were estimated from levoglucosan data to be on average 7.0 and 14% at daytime and nighttime, respectively, with maxima of 9.7 and 32% during the episodic transport events, indicating that biomass and biofuel burning activities in the rural parts of the Pearl River Delta and neighboring regions could have a significant impact on ambient urban aerosol levels.     

Worshippers' exposure to particulate matter in two temples in Taiwan

Worshippers in temples may be exposed to high concentrations of pollutants emitted from incense burning. This work assessed the PM2.5 and PM10 exposures of temple worshippers in Taiwan and explored the important exposure determinants such as numbers of passing visitors and joss sticks in censers, worshipping dates, and temple characteristics. Sampling was conducted on the 1st, 2nd, 15th, and 16th of the lunar month in two temples in Taichung, Taiwan. Research staff took samples by wearing one PM2.5 and one PM10 sampler and imitating worshipping activity. Personal environmental monitors connected to personal pumps with 2-L/min flow rates were used for sampling. PM10 samples were also simultaneously taken outside the temples. The results suggested that burning joss sticks in temples is a significant PM exposure source. The geometric mean of personal exposure was 444 microg/m3 PM2.5 [geometric standard deviation (GSD) = 1.8] and 583 microg/m3 PM10 (GSD = 1.4). The latter was approximately 4-6 times that of roadside concentrations. Exposures on the 1st and 15th (with more visitors and more joss sticks) were about 130 microg/m3 PM2.5 and 249 microg/m3 PM10 higher than those on the 2nd and the 16th. Furthermore, each joss stick in the censer contributed about 0.40 microg/m3 of particles to the worshippers' exposure. In the worst case, PM exposure during one temple visit would account for 11% of the personal exposure in one day.     

Multiple-pattern parameter identification and uncertainty analysis approach for water quality modeling

This paper presents a multiple-pattern parameter identification and uncertainty analysis approach for robust water quality modeling using a neural network (NN) embedded genetic algorithm (GA). The modeling approach uses an adaptive NN–GA framework to inversely solve the governing equations in a water quality model for multiple parameter patterns, along with an alternating fitness method to maintain solution diversity. The procedure was demonstrated through a coupled 2D hydrodynamic and eutrophication model for Loch Raven Reservoir in Maryland. The inverse problem was formulated as a nonlinear optimization problem minimizing the degree of misfit (DOM) between model results and observed data. A set of NN models was developed to approximate the input-output response relationship of the Loch Raven Reservoir model and was incorporated into a GA framework in an adaptive fashion to search for near-optimal solutions minimizing the DOM. The numerical example showed that the adaptive NN–GA approach is capable of identifying multiple parameter patterns that reproduce the observed data equally well. The resulting parameter patterns were incorporated into the numerical model, and a multiple-pattern robust water quality modeling analysis, along with a compound margin of safety (CMOS) method, was proposed and applied to analyze the parameter pattern uncertainty.     

OPTIMUM STORAGE VOLUME OF ROOFTOP RAIN WATER HARVESTING SYSTEMS FOR DOMESTIC USE1

ABSTRACT: Major parameters and optimum storage volumes of rooftop rain water harvesting systems (RRWHSs) have not been investigated in detail in Taiwan. Accordingly, the four major parameters of RRWHSs were herein identified and elucidated using a simulation method. Because the performance of the RRWHSs is sensitive to the runoff coefficient, a field experiment was conducted to determine the runoff coefficient more precisely for various types of roofs. A simulation model including production theory was developed and employed to estimate the most cost effective combination of the roof area and the storage capacity that best supplies a specific volume of water. Consequently, the expansion path of optimum solutions for different volumetric reliability of water supply can be determined. Additionally, the method based on the marginal rate of substitution can be used for determining the rational volumetric reliability. The procedures developed herein constitute an effective tool for preliminarily estimating the most satisfactory storage capacity of any specific roof area and for determining the rational reliability of a corresponding water supply.     

Generation rates and emission factors of particulate matter and particle-bound polycyclic aromatic hydrocarbons of incense sticks

The generation rates and emission factors of particulate matter and associated polycyclic aromatic hydrocarbons (PAHs) from incense burning were assessed in a laboratory setting. The differences among different segments of the same stick, among different sticks of the same kind of incense, and between two kinds of manually made Chih-Chen incense sticks (A and B) were evaluated. Joss sticks were burned inside a 44 cm long elutriator; personal environmental monitors fitted into the top of the elutriator were used to take PM2.5 and PM10 samples of incense smoke. Samples were analyzed for PAHs by gas chromatography-flame ionization Detector. It was found that particle and associated PAHs were generated approximately at 561 microg/min (geometric standard deviation (GSD) = 1.1) and 0.56 microg/min (GSD = 1.1) from Incense A, and at 661 microg/min (GSD = 1.7) and 0.46 microg/min (GSD = 1.3) from Incense B, respectively. One gram of Incense A emitted about 19.8 mg (GSD = 1.1) particulate matter and 17.1 microg (GSD = 1.2) particulate-phase PAHs, while one gram of Incense B produced around 43.6 mg (GSD = 1.1) of particles and 25.2 microg (GSD = 1.2) of particle-bound PAHs. There were significant differences in emissions between Incenses A and B, although they belong to the same class of incense. A 10-20% variability in emissions was observed in the main part of the manually produced stick, and a larger variation was found at both tips of the combustible part.     

Comparisons of the dust/smoke particulate that settled inside the surrounding buildings and outside on the streets of southern New York City after the collapse of the World Trade Center, September 11, 2001

The collapse of the World Trade Center (WTC) on September 11, 2001, generated large amounts of dust and smoke that settled in the surrounding indoor and outdoor environments in southern Manhattan. Sixteen dust samples were collected from undisturbed locations inside two uncleaned buildings that were adjacent to Ground Zero. These samples were analyzed for morphology, metals, and organic compounds, and the results were compared with the previously reported outdoor WTC dust/smoke results. We also analyzed seven additional dust samples provided by residents in the local neighborhoods. The morphologic analyses showed that the indoor WTC dust/smoke samples were similar to the outdoor WTC dust/smoke samples in composition and characteristics but with more than 50% mass in the <53-microm size fraction. This was in contrast to the outdoor samples that contained >50% of mass above >53 microm. Elemental analyses also showed the similarities, but at lower concentrations. Organic compounds present in the outdoor samples were also detected in the indoor samples. Conversely, the resident-provided convenience dust samples were different from either the WTC indoor or outdoor samples in composition and pH, indicating that they were not WTC-affected locations. In summary, the indoor dust/smoke was similar in concentration to the outdoor dust/smoke but had a greater percentage of mass <53 microm in diameter.     

Coating effects on the glass adsorption of polychlorinated biphenyl (PCB) congeners

The effects of coating materials on polychlorinated biphenyl (PCB) adsorption in aqueous solution were assessed in an attempt to minimize PCB sorption loss during sampling processes. A coating material, which enhances PCB adsorption and allows adsorbed PCBs to be readily extracted by solvents, can act as a sampling concentrator to reduce PCB losses from both adsorption and evaporation. Several coating materials were evaluated, including paraffin oil, silicone oil, dimethyldichlorosilane (Sylon-CT), Prosil 28^® and polydimethylsiloxane (PDS) with viscosity 0.65, 50 (PDS 50), and 500 (PDS 500) cSt. PDS and silicone oil enhanced adsorption for all five congeners examined (IUPAC No. 28, 52, 101, 138, and 180). Sylon-CT, paraffin oil and Prosil 28^® had inconsistent effects on adsorption of different congeners. Desorption of adsorbed PCBs onto all coating types was assessed. The recovery efficiency of extracting PCBs with solvents was enhanced greatly with all coatings as opposed to non-coated surfaces, with the exception of paraffin oil. Coating with silicon oil, PDS 50, and 500 resulted in virtually 100% recovery of adsorbed PCBs. It was also found that Teflon containers were poor substitutes for glass containers and failed to minimize PCB losses. Among the materials studied, the best coating that could be used as a sampling concentrator was PDS 500.     

Conservation impacts of commercial cultivation of endangered and overharvested plants

Overharvesting is one of the greatest threats to species survival. Farming overharvested species is a conservation strategy that can meet growing market demand and conserve wild populations of the target species. This strategy is compatible with the international community's desire to uphold the right of local communities to use biological resources to support their livelihoods. However, studies investigating whether farming can alleviate poaching pressure have focused almost exclusively on animals. To address the shortfall in plant-focused studies, we compiled information on commercial cultivation of threatened plants to assess its conservation benefits. Because China's rising middle class has rapidly intensified demand for wildlife products, we searched the scientific literature published in Chinese (China National Knowledge Infrastructure and Baidu) and in English. We found 32 reports that contained data on 193 internationally or nationally threatened plant species that were under commercial cultivation. These reports showed that cultivations of 82% of the 193 species were sustained by collecting whole plants from the wild periodically or continuously. Although based on a small sample size, species that were maintained in cultivation only through artificial propagation or seeds collected in the wild were likely associated with a reported reduction in wild harvesting of whole plants. Even so, results of correlation analyses suggested that production system, scale, and when a species began being cultivated had little effect on conservation status of the species, either globally or in China. However, species brought into cultivation relatively recently and on a smaller scale were more likely to have undergone a reduction in collecting pressure. Farming of nonmedicinal plants was most problematic for species conservation because wild plants were laundered (i.e., sold as cultivated plants). For effective conservation, policy to guide cultivation operations based on the target species’ biological characteristics, cultural significance, market demand, and conservation status is needed.