The Autothermal Pyrolysis of Waste Tires

Abstract

The growing amount of rubber waste, such as that from tires and cables, has resulted in serious environmental problems. Since rubber waste is not easily biodegradable even after a long period of landfill treatment, material and energy recovery is the preferable alternative to disposal. The potential offered by waste tire pyrolysis for solving both energy and waste treatment problems is widely recognized. Pyrolysis is one method of inducing thermal decomposition without using any oxidizing agent, or using such a limited supply of the agent that oxidization does not proceed to an appreciable extent. The latter may be described as autothermal pyrolysis and will be studied in the present work.

The main objective of this research was to study the operating parameters of autothermal pyrolysis of scrap tires in a laboratory-scale fluidized bed reactor with a 100-cm bed height (10 cm I.D.) and a 100-cm freeboard (25 cm I.D.). Scrap tires were pyrolyzed in a limited oxygen supply, so that the heat for pyrolysis of the scrap tires was provided by combustion of some portion of the scrap tires. The operating parameters evaluated included the effect on the pyrolysis oil products and their relative proportions of (1) the air factor (O.O7–O35); (2) the pyrolysis temperature (370–570 °C); and (3) the catalyst added (zeolite and calcium carbonate). The results show that: (1) the composition of the liquid hydrocarbon obtained is affected significantly by the air factor; (2) the higher operating temperature caused a higher yield of gasoline and diesel; (3) the yield of gasoline increased due to the catalyst zeolite added, and the yield of diesel increased due to the addition of the catalyst calcium carbonate; (4) the principal constituents of gasoline included dipentene and diprene.     

Site-specific phosphorus application based on the kriging fertilizer-phosphorus availability index of soils

Site-specific phosphorus management is done to optimize crop production and minimize P loss from soils. The spatial variability of the available P prior to fertilizer application and the P-fixation tendency of soil both need to be taken into account for variable-rate P application. The objectives of this research were to document the spatial variability of the fertilizer-P availability index, which shows the P-fixation tendency, and to develop a strategy that takes the spatial distribution of this index into account for site-specific phosphorus application. In this study, the spatial patterns of the fertilizer-P availability index were characterized by using geostatistics. The ordinary kriging was used for spatial interpolation of the fertilizer-P availability index. Because the fertilizer-P availability index of soil is related to oxalate-extractable Fe and Al and because measuring oxalate-extractable Fe and Al is much easier than directly determining the fertilizer-P availability index, the spatial distribution of the fertilizer-P availability index can be obtained using the oxalate-extractable Fe and Al data. The spatial distribution of Olsen-extractable P, which was used to measure the available-P status prior to fertilizer-P application, was also estimated by using ordinary kriging. The required fertilizer-P amounts were then determined using the kriging estimates of the fertilizer-P availability index and Olsen-extractable P. A fertilizer-P recommendation map for the 430-ha study site in Changhua county, Taiwan was generated by using this approach for illustration. The proposed method for generating fertilizer-P recommendation maps can be used for variable-rate application to maintain an adequate P status for crop production and to potentially reduce the P loss from soils.     

Supported Pd/Sn bimetallic nanoparticles for reductive dechlorination of aqueous trichloroethylene

A Pd/Sn bimetallic nanoparticles resin (nano-Pd/Sn/resin) was successfully synthesized for reductive transformation of aqueous trichloroethylene (TCE). The physicochemical properties of the prepared resin were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, N(2) isothermal sorption at and X-ray photospectroscopy. The surface-area-normalized rate constants (k(SA)) of Sn particles in the nanoscale range (50-100 nm) were 4.5 times larger than the k(SA) for powdered Sn (0.04 mm). After depositing 1 wt% Pd onto nano-Sn surface, k(SA) was further enhanced by about a factor of 2. Groundwater constituents such as sulfide nitrate and dissolved oxygen had significant negative effects on the rate of TCE degradation by the nano-Pd/Sn/resin. A wet-chemical method regeneration method was observed to effectively restore the reactivity of the poisoned nano-Pd/Sn/resin after dipping in sulfide solution for 2d. In all cases, less than 0.5% of the degraded TCE appeared as chlorinated byproducts including the three dichloroethene isomers. The nano-Pd/Sn/resin technique performs well in transforming TCE into nontoxic hydrocarbons, as compared with other published methods.     

Applications of open-path Fourier transform infrared for identification of volatile organic compound pollution sources and characterization of source emission behaviors

An open-path Fourier transform infrared spectroscopy (OP-FTIR) system was set up for 3-day continuous line-averaged volatile organic compound (VOC) monitoring in a paint manufacturing plant. Seven VOCs (toluene, m-xylene, p-xylene, styrene, methanol, acetone, and 2-butanone) were identified in the ambient environment. Daytime-only batch operation mode was well explained by the time-series concentration plots. Major sources of methanol, m-xylene, acetone, and 2-butanone were identified in the southeast direction where paint solvent manufacturing processes are located. However, an attempt to uncover sources of styrene was not successful because the method detection limit (MDL) of the OP-FTIR system was not sensitive enough to produce conclusive data. In the second scenario, the OP-FTIR system was set up in an industrial complex to distinguish the origins of several VOCs. Eight major VOCs were identified in the ambient environment. The pollutant detected wind-rose percentage plots that clearly showed that ethylene, propylene, 2-butanone, and toluene mainly originated from the tank storage area, whereas the source of n-butane was mainly from the butadiene manufacturing processes of the refinery plant, and ammonia was identified as an accompanying reduction product in the gasoline desulfuration process. Advantages of OP-FTIR include its ability to simultaneously and continuously analyze many compounds, and its long path length monitoring has also shown advantages in obtaining more comprehensive data than the traditional multiple, single-point monitoring methods.     

Predicting the contents of BTEX and MTBE for the three types of tollbooth at a highway toll station via the direct and indirect approaches

This study was set out to assess the contents of five volatile organic compounds (VOCs), including BTEX (the acronym for benzene, toluene, ethylbenzene, and xylene) and methyl tertiary-butyl ether (MTBE), in three types of tollbooth (including the car lane/ticket-collecting, car lane/cash-collecting, and bus/truck lane tollbooths) at a highway toll station via the direct and indirect approaches. For the direct approach, VOC samples were collected from the breathing zone of booth attendants at all selected tollbooths during the three workshifts. For samples collected during the dayshift, we found VOC contents of BTEX and MTBE in both the car lane/ticket-collecting (=6.23, 21.93, 3.24, 8.56, and 5.63 ppb, respectively) and car lane/cash-collecting tollbooths (=5.98, 21.71, 3.25, 8.59, and 6.04 ppb, respectively) were quite comparable, but both were significantly higher than that in the bus/truck lane tollbooth (=3.13, 13.91, 2.05, 4.52, and 2.70 ppb, respectively). The same pattern can also be found for the other two workshifts. For the indirect approach, we conducted multivariate regression analyses to predict VOC contents for any given type of tollbooth by using the four independent variables of the vehicle flowrate, wind speed, relative humidity, and air temperature. We found that, except the vehicle flowrate, the other three factors did not have a significant effect on VOC contents in the three types of tollbooth. In addition, the magnitudes of the effect of the vehicle flowrate on VOC contents for the three types of tollbooth were: car lane/cash-collecting>bus/truck lane>car lane/ticket-collecting. All regression results yielded R²-values in the range of 0.41−0.74 indicating that the developed indirect approach was able to predict VOC contents for three types of tollbooth.     

Oxidation of TNT by photo-Fenton process

A series of photo-Fenton reactions have been performed for the degradation of 2,4,6-trinitrotoluene (TNT) in a 4.2-l reactor. The degradation reaction rate of TNT followed a pseudo-first-order behavior; and the rate constants for 2.4mW cm(-2)UV only, 2.4mW cm(-2)UV/H(2)O(2), Fenton, photo-Fenton (2.4mW cm(-2)) and photo-Fenton (4.7mW cm(-2)) were 0.002min(-1), 0.007min(-1), 0.014min(-1), 0.025min(-1) and 0.037min(-1), respectively. Increasing the intensity of UV light, and the concentrations of ferrous ions and hydrogen peroxide promoted the oxidation rate under the experimental conditions in this study. The weighting factor (f), the Fe(II)-promoted efficiency (r) and the promoted-UV light efficiency (p) were calculated to clarify their effects on the TNT oxidation. Moreover, the inhibition effect of hydroxyl radical was also observed in both Fenton and photo-Fenton oxidation when the concentration of Fe(II) were higher than 2.88mM. Solid phase micro-extraction was first applied to the separation of the organic byproducts from TNT oxidation. GC/MS was employed to identify the byproducts during the Fenton and photo-Fenton oxidation of TNT. These compounds were clarified as 1,3,5-trinitrobenzene, 1-methyl-2,4-dinitrobenzene 2,5-dinitrobenzoic acid and 1,3-dinitrobenzene. By these byproducts, the mechanisms of the methyl group oxidation, decarboxylation, aromatic ring breakage, and hydrolysis can be recognized and demonstrated. The pathway of TNT oxidation by photo-Fenton process was also proposed in this study.     

The placement strategies of structural best management practices for different moving rainstorms

Hydrological responses and pollutant exports are always highly related to rainfall characteristics. Many studies have demonstrated that the influence of moving rainstorm on flows and mass transport process in hydrologic systems cannot be ignored. Best management practices (BMPs) are popularly applied for controlling water quantity and water quality in a watershed. Since the movements of rainstorm can influence watershed responses, BMP placement strategies should be suitably adjusted in different moving rainstorms. This study designed an intermediate rainfall pattern with varied movement behavior and tried to find the optimal BMP placement strategies, which cannot only satisfy environmental standards but also improve economic benefits, for the rainfall events. The result shows that the control efficiency of pollutant and runoff can highly improve when the BMPs are set near the outlet of a watershed. Since the economic efficiency is always regarded as an important factor, the BMP placement strategy is significant for watershed conservation and management.     

Prenatal diagnosis of a fetus harboring an intermediate load of the A3243G mtDNA mutation in a maternal carrier diagnosed with MELAS syndrome

We prenatally diagnosed MELAS syndrome in a fetus whose mother and older brother had the MELAS-specific A3243G mutation. The mutant mtDNA level of the amniotic fluid cells was not significantly different from that of the postnatal peripheral blood and hair follicle samples. The obstetrical course was uncomplicated except for transient exacerbation of the mother's diabetes, which required insulin control. At term, the infant was macrosomic, and the delivery was complicated by shoulder dystocia. MELAS syndrome in itself does not influence either the prenatal course of the mother or the fetal outcome. In contrast to the fulminating clinical course of this mother's first child, MELAS symptoms did not develop in her second child until age four, despite similar high tissue levels of mutant mtDNA. The phenotypic diversity in two offspring with similar higher levels of mutant mtDNA suggests that prenatal genetic diagnosis of cultured amniotic cells may yield results that are poor prognosticators of fetal outcome. Copyright © 2004 John Wiley & Sons, Ltd.     

Inorganic arsenic exposure and its relation to metabolic syndrome in an industrial area of Taiwan

Past arsenic exposure was found associated with increased incidence of type 2 diabetes. However, the mechanisms remain unclear. Metabolic syndrome has been shown as a strong predictor for diabetes occurrence. We aimed at examining the association of inorganic arsenic exposure and the prevalence of metabolic syndrome. The authors recruited 660 age and gender stratified random population of residents in central Taiwan during 2002-2003. They received home interviews and health examinations at local health care units, where blood and hair specimens were collected. Hair arsenic (H-As) concentrations were determined by inductively coupled plasma-mass spectrometry. Metabolic syndrome was defined as the presence of three or more of the following risk factors: elevated levels of blood pressure, plasma glucose, and triglycerides, also the body mass index, and reduced high-density lipoprotein. Prevalence of metabolic syndrome increased from the 2nd tertile (0.034 ug/g) of H-As levels (odds ratio=2.54, 95% confidence interval: 1.20-5.39, p=0.015) after the adjustment for age, gender, occupation and life styles including cigarette smoking. We further found linear relation between H-As concentrations and increased levels of plasma glucose and lipids, and blood pressures. This first report may help identify modifiable factors associated with diabetogenesis and cardiovascular disease progression and thus be worth following for community health.     

Comparison of titania nanotubes and titanium dioxide as supports of low-temperature selective catalytic reduction catalysts under sulfur dioxide poisoning

A series of iron–manganese oxide catalysts supported on TiO₂ and titanium nanotubes (TNTs) were studied for low temperature selective catalytic reduction (SCR) of NO with NH₃ in the presence of SO_2. The results showed that the specific surface area and the amount of Brønsted acid sites were highly correlated. The results also demonstrated that higher Mn⁴⁺/Mn³⁺ ratios and larger specific surface areas might be the main reasons for the excellent performance of MnFe-TNTs catalyst after SO₂ poisoning. The SO₂ poisoning effect could be minimized by reducing the GHSV, increasing the reaction temperature, or increasing the [NH₃]/[NO] molar ratio. The results also indicated that the formation of ammonium sulfate had a stronger effect on the NO conversion efficiency as compared to the formation of metal sulfate. Thus operating the low temperature SCR at above 230 ^oC to avoid the formation of ammonium sulfate would be the priority choice when SO₂ poisoning is a concerned issue.?Implications: Low-temperature selective catalytic reduction (SCR) has attracted increasing attention due to that it can reduce the energy consumption for the SCR process employed in industries such as steel plants and glass manufacturing plants. However, it also suffers from the sulfur dioxide (SO₂) poisoning problem. This study investigates the possibility of using titania nanotubes (TNTs) as the support of Mn/Fe bimetal oxide catalysts for low-temperature SCR to reduce the SO₂ poisoning. The results indicated that the MnFe-TNT catalyst can tolerate SO₂ for a longer time as compared with the MnFe-TiO₂ catalyst.