城市能源利用与环境保护的综合管理初探

能源短缺和环境污染已成为中国推行全面协调可持续发展的重要制约因素,作为能源消耗的主体和环境污染的控制重点,在城市层面推动能源发展战略的转变和强化环境保护是发展的基本要求.鉴于能源与环境之间的高度关联性,在管理方面要求对能源发展和环境保护进行统筹考虑和综合管理,充分强调能源经济效率和环境制约因素在能源发展中的作用.通过制定合理的产业能效标准和排放绩效标准,为城市经济、能源和环境的可持续性发展提供科学性、系统性决策支持.     

亚热带稻田土壤碳氮磷生态化学计量学特征

为了解稻田土壤中是否存在稳定的土壤有机碳(C)、氮(N)和磷(P)比值,基于亚热带区110个水稻土剖面和587个发生层的土壤调查数据库,在区域尺度上分析了典型水稻土C∶N∶P比值的生态化学计量学特征,并应用相关分析和冗余分析,研究水稻土C∶N∶P比值与土壤-环境因子(地形和母质、土壤发生层、土壤类型和土壤理化性质)的关系.结果显示,亚热带区稻田土壤C∶N、C∶P和N∶P的剖面加权平均值分别为12. 6、49和3. 9,C∶N∶P为38∶3. 2∶1.不同母质起源、不同土壤亚类和不同发生层的水稻土C∶N变异相对较小;但C∶P和N∶P的变异很大,两者均值也远低于全球(186和13. 1)和中国土壤(136和9. 3)的C∶P和N∶P的平均水平.尽管稻田土壤剖面的C∶N∶P相对不稳定,但由于稻田表土生物与环境相互作用强烈,表土C∶N相对稳定(14. 2).这反映长期水耕熟化作用下,稻田表土中C和N仍存在紧密的耦合作用.然而,在稻田土壤剖面上,C∶P和N∶P并不稳定,SOC与全P含量、全N与全P含量也无显著相关性,表明环境变化可能导致土壤C∶N∶P解耦.地形、土壤质地、氧化铁和容重是调控稻田土壤剖面C∶N∶P的关键土壤环境因子.     

基于两种再分析资料的一次四川盆地大气污染过程气象要素数值模拟研究

利用ECMWF-ERA5和NCEP-FNL再分析资料作为中尺度气象模式WRF（The Weather Research and Forecasting）初始场,对四川盆地2018年1月一次大气污染过程气象要素进行了模拟,对比分析了气温、风速、风向、相对湿度、边界层高度、温廓线的模拟效果,并结合大气超级站观测数据对模拟结果进行评估.结果表明：两种资料均能较好地模拟出气象要素的变化情况,但由于两套资料时空分辨率、采用的模式、同化方案、数据来源和质量控制方案存在一定区别,导致各要素模拟效果并不一致.与NCEP-FNL相比,ECMWF-ERA5模拟的平均相对湿度（59.23%）与观测值差异更小,且均方根误差、偏差较小,分别为9.83%和-0.83%,但NCEP-FNL模拟的平均气温（8.99℃）更接近观测值,且偏差值较小,为-0.04℃.两组模拟结果均显示盆地内部为模拟区域的低风速区,相对湿度模拟值在60%以上,气温高于西部山地地区.NCEP-FNL模拟的盆地内部气温、相对湿度、风速小于ECMWF-ERA5模拟值,但边界层高度模拟值较大.ECMWF-ERA5模拟的逆温强度相比较小,且温度露点差较小.此次污染过程PM_2.5和PM₁₀日均浓度最大值分别为190.1 μg·m^-3和261.0 μg·m^-3,相对湿度增大引发的颗粒物吸湿增长是导致PM_2.5和PM₁₀质量浓度突增的主要原因.     

深圳市秋季大气臭氧立体分布特征

利用大气O₃探测激光雷达在深圳市东部生态区和西部城区同步开展垂直观测,探究了2018年深圳市O₃立体分布在秋季光化学污染活跃期至冬季非活跃期的演变过程.结果表明：光化学反应活跃的10月,东部地面O₃浓度相对于西部地面高出约128%;地面向上至450m,O₃浓度在东部生态区发生快速降低,而在西部城区由于存在“滴定效应”,O₃浓度随高度升高而升高;450m~2km,东、西部O₃浓度均随高度升高而降低,西部城区O₃浓度水平超过东部生态区约30%;2km以上高空,东、西部O₃浓度趋同（70μg/m³）,并保持稳定,为具深圳市秋季O₃污染过程提供了较高的大气背景浓度.高污染期间,深圳市大气边界层内O₃浓度变化较为一致,西部高空的O₃区域传输作用更加显著.秋季至冬季光化学反应逐渐减弱,深圳市O₃浓度的水平和垂直空间差异逐渐减小,冬季的深圳市O₃污染基本受大气背景控制.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Reviews of emission of biogenic volatile organic compounds (BVOCs) in Asia

Biogenic volatile organic compounds (BVOCs) in the atmosphere play important roles in the formation of ground-level ozone and secondary organic aerosol (SOA) in global scale and also in regional scale under some condition due to their large amount and relatively higher reactivity. In places with high plant cover in the tropics and in China where air pollution is serious, the effect of BVOCs on ozone and secondary organic aerosols is strong. The present research aims to provide a comprehensive review about the emission rate, emission inventory, research methods, the influencing factors of BVOCs emissions, as well as their impacts on atmospheric environment quality and human health in recent years in Asia based on the summary and analysis of literatures. It is suggested to use field direct measurement method to obtain the emission rate and model method to calculate the emission amount. Several recommendations are given for future investigation and policy development on BVOCs emission.     

典型脱硫工艺对燃煤锅炉烟气颗粒物的影响

脱硫是燃煤锅炉的重要除污环节,为探究脱硫工艺对烟气颗粒物的影响,选取4台不同脱硫工艺（石灰石/石膏法、炉内喷钙法、氨法和双碱法）的燃煤锅炉,利用再悬浮采样法和稀释通道采样法分别采集脱硫前后烟气颗粒物样品,并测定颗粒物中的水溶性离子、无机元素和碳组分.结果表明,脱硫剂对烟气PM_2.5的组分构成产生影响,烟气经过石灰石/石膏法脱硫后,PM_2.5中的Ca由5.1%提高至24.8%;经过氨法脱硫后,PM_2.5中NH₄⁺的质量分数由0.8%提高到7.3%;双碱法脱硫则使烟气PM_2.5中Na由0.9%提高到1.7%.湿法和干法脱硫工艺的作用显著不同,湿法脱硫排放颗粒物的离子含量较高,经过石灰石/石膏法和氨法脱硫,PM_2.5中SO₄^2-的质量分数分别由2.0%和6.7%提高到9.6%和11.9%,Cl^-分别由0.4%和1.2%提高到3.8%和5.2%,而Cr、Pb、Cu、Ti和Mn等重金属经过湿法脱硫出现含量下降;相对湿法脱硫,干法脱硫燃煤锅炉排放的PM_2.5中富含Al、Si和Fe等地壳元素.湿法脱硫同样对碳组分产生影响,石灰石/石膏法和氨法脱硫后,烟气PM_2.5的元素碳EC质量分数分别从6.1%降至0.9%和从3.6%降至0.7%,但是有机碳OC的含量并没有下降.     

郑州市氧化铝工业炉窑污染物及源谱特征

采用稀释通道采样法对郑州市一家拜耳法氧化铝企业及一家α-氧化铝企业的PM_2.5、PM₁₀样品进行采集,利用烟气分析仪检测SO₂和NO_x气体的质量浓度.对颗粒物样品中的38种化学组分进行分析,构建相应的源成分谱,运用分歧系数（CD）和组分差异权重分布函数R/U对其特征进行对比研究.结果表明：α-氧化铝源谱中以Cl^-为主（质量分数18.29%~25.21%）,拜耳法氧化铝源谱中以OC和NO₃^-为主（质量分数9.01%~41.87%）.源谱间的分歧系数（CD）显示,同一种生产工艺两种粒径间的源谱比较相似,相同粒径的两种生产工艺之间的源谱差异较大.R/U值对比结果显示,EC、Ca、F^-和Cl^- 4种元素可作为区分两种氧化铝生产工艺的标识组分.     

Mercury flows in large-scale gold production and implications for Hg pollution control

Large-scale gold production(LSGP) is one of the five convention-related atmospheric mercury(Hg) emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process of LSGP are limited. To identify the atmospheric Hg emission points and understand Hg emission characteristics of LSGP, Hg flows in two gold smelters were studied. Overall atmospheric Hg emissions accounted for 10%–17% of total Hg outputs and the Hg emission factors for all processes were 7.6–9.6 kg/ton. There were three dominant atmospheric Hg emission points in the studied gold smelters, including the exhaust gas of the roasting process, exhaust gas from the environmental fog collection stack and exhaust gas from the converter of the refining process. Atmospheric Hg emissions from the roasting process only accounted for 16%–29% of total emissions and the rest were emitted from the refining process. The overall Hg speciation profile(gaseous elemental Hg/gaseous oxidized Hg/particulate-bound Hg) for LSGP was 34.1/57.1/8.8. The dominant Hg output byproducts included waste acid, sulfuric acid and cyanide leaching residue. Total Hg outputs from these three byproducts were 80% in smelter A and 84% in smelter B. Our study indicated that previous atmospheric Hg emissions from large-scale gold production might have been overestimated.Hg emission control in LSGP is not especially urgent in China compared to other significant emission sources(e.g., cement plants). Instead, LSGP is a potential Hg release source due to the high Hg output proportions to acid and sludge.