小型废电池填埋焚烧处置的健康风险分析

对废电池采取填埋、焚烧处置所引起的健康风险进行了分析，采用3种模型，分别研究了废电池随城市固体废物一起完全填埋处置，一起完全焚烧处置，一起部分填埋处置和部分焚烧处理时，可能引起的健康风险，由分析可知，镉镍电池焚烧过程将引起不可接受的致癌风险，填埋废电池也会引起重金属非致癌风险，提出在现阶段没有单独收集分类管理的条件下，对于小型废电池应采取填埋焚烧联合处置的办法，但应避免镉镍电池的焚烧，在建立了收集体系后，应该分类进行资源化和无害化管理。     

城市生活垃圾理化性质的动态特性分析

对太原市城市生活垃圾的组成、化学元素及重金属等进行了1年(每月2次)共24次的分析。结果表明,太原市生活垃圾的组成在焚烧过程中,能产生低位热值(Q低)的有机物占(44.28±2.24)％,不产生低位热值的无机物占(13.94±2.01)％,混合物(破碎的动植物碎片及粘附在其上面的灰、土、砂)占(43.36±8.67)％。垃圾中可燃物比例较高,水分含量较低,有利于焚烧和热解,低位热值(Q低)平均值为(5590.8±1252.3)kJ/kg,但低位热值随季节变化较大。垃圾中化学元素硫(S)、氯(Cl)、氮(N)、氢(H)、碳(C)、氧(O)的年平均值分别为(0.20±0.13)％、(0.48±0.11)％、(0.87±0.18)％、(2.56±0.76)％、(30.78±4.06)％、(16.42±5.17)％,与其他城市相比,S、N、Cl的含量较高。垃圾中的重金属铅(Pb)、镉(Cd)的年平均值分别为41.94mg/Kg和1.806mg/kg;汞(Hg)含量变化较大。焚烧后的灰渣中,Pb部分挥发,Cd得到富集,但几乎无Hg检出。     

用滚筒焚烧工艺处理高浓度有机废水

论述了一种处理高浓度有机废水的新工艺——滚筒焚烧处理工艺形成过程，并获得了处理江西德兴市异VC钠有限公司生产产生的高浓度有机废水(CODcr40—50万mg／L)的工艺参数和技术经济指标。     

城市污水厂污泥热干燥处理技术及其应用分析

提出采用热干燥处理技术进一步降低脱水泥饼的含水率，介绍了现行的污泥热干燥处理技术，并就该技术在污泥处理中的应用尤其是在焚烧预处理中的应用进行了分析。     

医疗废物焚烧中二恶英的产生及控制

医疗废物的安全处置一直被世界各国所重视,我国自SARS灾难后,强化了医疗废物的治理力度。本文针对目前主要采用焚烧法处置医疗废物过程中二恶英的生成途径进行了论述,并结合二恶英的分子结构、毒性及危害提出了控制对策与建议。     

城市模化垃圾焚烧烟气中二氧化硫的生态特性

对模化广州市城市生活垃圾进行焚烧处理 ,从燃烧温度、炉内停留时间、过量空气系数以及垃圾尺寸等方面研究了 SO2 的生成特性和控制条件。     

城市生活垃圾焚烧对大气的污染问题

本文对我国城市有机混合垃圾经模化后,在过剩空气系数α?2,温度在700～900℃条件下焚烧的气态排放物进行了定性和定量分析.实验结果表明:烟气呈碱性,主要污染物NH_2的排放浓度最高.HCl次之,NO_x<100ppm,SO_x<1ppm,H_2S<10ppm.     

The economics of tire remanufacturing

The world market for tires is described to identify the current material flow from raw materials to tires and the used tire disposal problem. Then, I describe the value-adding operations in the tire production process and in the tire retreading process. Once retreading is identified as the only recovery alternative that maximizes tire utilization, I explain why heat generation is the only recovery alternative, when retreading is not technically feasible. The economic values of heat generation in electric plants and in cement kilns are discussed. The paper culminates with the case of retreading, the tire remanufacturing process and the recommendation of a simple decision rule for selecting the number of times a tire should be retreaded to maximize its utilization.     

Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste

This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC’s combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink.     

Comparative assessment of municipal sewage sludge incineration,gasification and pyrolysis for a sustainable sludge-to-energy management in Greece

For a sustainable municipal sewage sludge management, not only the available technology, but also other parameters, such as policy regulations and socio-economic issues should be taken in account. In this study, the current status of both European and Greek Legislation on waste management, with a special insight in municipal sewage sludge, is presented. A SWOT analysis was further developed for comparison of pyrolysis with incineration and gasification and results are presented. Pyrolysis seems to be the optimal thermochemical treatment option compared to incineration and gasification. Sewage sludge pyrolysis is favorable for energy savings, material recovery and high added materials production, providing a ‘zero waste’ solution. Finally, identification of challenges and barriers for sewage sludge pyrolysis deployment in Greece was investigated.