经口摄入土壤多溴联苯醚生物可给性变化及影响因素的体外消化模拟

误食土壤是污染物(如多溴联苯醚)人体(主要是儿童)暴露的重要途径,人体消化道内污染物吸收的生物可给性是针对此种暴露方式进行定量风险评估的有效途径之一.本研究采用体外消化实验模拟3种不同有机碳含量的天然土壤中典型多溴联苯醚(BDE-28、BDE-47、BDE-99和BDE-153)在胃和小肠消化液中的释放,验证部分消化释放的多溴联苯醚因消化残留固相表面的再吸附造成低估实际生物可给性,并通过不同水土比的拟合计算予以校正.结果表明,校正后的消化率普遍高于校正前;就不同土样而言,BDE-28、BDE-47、BDE-99和BDE-153在不同初始暴露浓度条件下平均提升比例范围分别为14.3%~42.3%、11.1%~32.1%、4.9%~12.3%和0.0%~7.7%.因此,未经校正的消化率会显著低估PBDEs消化道内的生物可给性,尤其是低溴代组分及PBDEs初始浓度较高或高TOC含量的土样.校正后BDE-28、BDE-47、BDE-99和BDE-153的消化率分别维持在21.9%~54.7%、18.8%~43.1%、13.4%~27.2%和9.3%~19.9%.此外,PBDEs的消化率与其辛醇-水分配系数的对数lg KOW呈显著负相关;而与土壤TOC含量及PBDEs初始暴露浓度的相关性并不显著,尤其是高溴代组分.     

In vitro approaches to assess bioavailability and human gastrointestinal mobilization of food-borne polychlorinated biphenyls (PCBs)

This study reports on the potential for gastrointestinal (GI) mobilization and bioavailability of food-borne PCBs in humans. The development and validation of a GI simulator and operational protocols, developed in compliance with the requirements of German DIN 19738 risk assessment test procedure, are presented. Food, naturally contaminated with PCBs, was homogenized with simulated saliva fluid and shaken in the GI simulator with simulated gastric fluids (containing pepsin, mucine) for 2 h at 37°C. Afterwards, the simulated intestinal fluids (containing pepsin, mucine, trypsin, pancreatin, bile) were added and the mixture shaken for a further 6 h prior to centrifugation and filtration using Buchner funnels to separate the undigested GI residues from GI fluids. PCBs were recovered from GI residues and fluids by Soxhlet and liquid-liquid extraction respectively, cleaned up using silica-SFE, and analyzed by gas chromatography mass spectrometry detection (GC-MSD). Detailed studies with fish indicate variations in mobilization and bioavailability of Σ PCBs (28, 52, 101, 118, 153, 138 and 180). For example, the bioavailable fractions (fractions mobilized) in mackerel, salmon, crab and prawn were 0.77, 0.60, 0.54, and 0.72 respectively of the Σ PCBs initially present in these food samples. The bioavailable fraction was dependent on the physicochemical characteristics of the PCBs. In mackerel bioavailable fractions for individual PCB congeners ranged from 0.47–0.82, from 0.30–0.70 in salmon, 0.44–0.64 in crab and in prawn from 0.47–0.77. Future studies will focus on understanding better, the variability in bioavailable fractions to be expected for different foodstuffs, in addition to tissue culture techniques using human gut cell lines to investigate a simultaneous mobilization and absorption of food-borne PCBs.     

Geochemistry of a septic-system plume in a coastal barrier bar, Point Pelee, Ontario, Canada

The major ion and trace metal geochemistry of a septic system plume in a shallow sand aquifer was characterized to assess geochemical processes controlling the transport of nutrients and their release to a nearby wetland. The plume was generated from a 16-year-old tile bed, and is more than 60 m long, 40 m wide and 7 m thick. The groundwater pH at the site is near neutral, but up to 0.4 units lower in the plume core as a result of H⁺ generated from NH₃ and DOC oxidation in the unsaturated zone. The plume can be divided into distinct redox zones, which show differences in nutrient mobility. Proximal to the tile bed, there is a shallow suboxic zone, with intermediate Eh values (>400 mV), low concentrations of dissolved oxygen (<1.0 mg/l), and elevated concentrations of Mn (1–3 mg/l) and nutrients (10–80 mg/l NO₃–N, 1–15 mg/l NH₃–N, 0.1–1.5 mg/l PO₄–P, 6–13 mg/l dissolved organic carbon). At the base of the aquifer, there is a reduced zone (Eh<200 mV) with elevated concentrations of Fe (1–14 mg/l), PO₄ and NH₃, but negligible concentrations of NO₃ (<0.01 mg/l N). Distal from the tile bed, the shallow groundwater is suboxic to oxic, and has elevated concentrations of NO₃ and NH_3, but negligible PO₄. In the lower reduced zone, elevated concentrations of PO₄ occur up to 60 m away. The release of groundwater containing even very low concentrations of PO₄ (<0.02 mg/l P) can lead to the development of eutrophic conditions in surface water bodies. Geochemical calculations indicate that, in the Mn-rich zone, the groundwater is close to saturation or supersaturated with respect to hydroxyapatite, rhodochrosite, calcite and ferrihydrite. In the reduced zone, the groundwater is close to saturation or supersaturated with respect to hydroxyapatite, vivianite, calcite and siderite. Formation of these phases, or related phases, are likely limiting the concentrations of dissolved PO₄, Fe and Mn and controlling the geochemical evolution of the plume.     

Three-dimensional patterns of moisture, water repellency, bromide and pH in a sandy soil

Soil water repellency might lead to preferential flow of water and solutes through the unsaturated zone of soils. To study this process in a water repellent sandy field soil, a bromide tracer had been applied on a 2.2 m long and 0.4 m wide plot. The bromide application rate was 8 g/m², and the plot was sampled using 100 cm³ steel cylinders after 52 mm of rainfall in 12 days. A total of seven layers were sampled to a depth of 74 cm. Each layer was sampled at 240 locations in a 40 by 6 grid. All samples were used for the determination of soil water content, degree of actual and potential water repellency, bromide concentration and pH. The spatial distribution of these properties was visualized three-dimensionally and compared. The degree of water repellency, bromide concentration, and pH distribution bore close resemblance to the fingered flow induced soil water content distribution. The degree of potential water repellency was relatively low in places with such fingers. Actual water repellency occurred between the fingers at the dry spots. Bromide was not found, or only in very low concentrations, in such places. Bromide depth profiles clearly indicated the occurrence of diverging flow in the wetter subsoil. Most likely, manuring activities during the last decades resulted in relatively high pH values in the topsoil, and in the subsoil along the recurring fingered flow pathways.     

Hydrological and geochemical factors affecting leachate composition in municipal solid waste incinerator bottom ash: Part I: The hydrology of Landfill Lostorf, Switzerland

The objective of the investigation of the municipal solid waste incinerator (MSWI) bottom ash landfill, Landfill Lostorf, was to determine the residence time of water in the landfill and the flow paths through the landfill. Over a period of 22 months, measurements of rainfall, landfill discharge and leachate electrical conductivity were recorded and tracer experiments made. Over the yearly period 1995, approximately 50% of the incident rainfall was measured in the discharge. An analysis of single rain events showed that in winter, 90–100% of rainfall was expressed in the landfill discharge, whereas in summer months, the value was between 9 and 40% depending on the intensity of the rain event. The response to rainfall was rapid. Within 30–100 h, approximately 50% of water discharged in response to a rain event had left the landfill. The discharge was less than 4 l/min for approximately 50% of the measurement periods. Qualitative tracer studies with fluorescein, pyranine and iodide clearly showed the existence of preferential flow paths. This was further substantiated by quantitative tracer studies of single rain events using / ratios and electrical conductivity measurements. The proportion of rainwater passing directly through the landfill was found to be between 20 and 80% in summer months and around 10% in winter months. The difference has been ascribed to the water content in the landfill. The average residence time of the water within the landfill has been estimated to be roughly 3 years and this water is the predominant component in the discharge over a yearly period.     

Evaluation of Saccharomyces cerevisiae strains as probiotic agent with aflatoxin B1 adsorption ability for use in poultry feedstuffs

In this study the aflatoxin B₁ (AFB₁) removal capacity, the tolerance to salivary and gastrointestinal conditions, autoaggregation and coaggregation with pathogenic bacteria of Saccharomyces cerevisiae strains isolated from broiler feces, were evaluated. Only four of twelve isolated strains were identified as Saccharomyces cerevisiae using molecular techniques. The results obtained in AFB₁ binding studies indicated that the amount of AFB₁ removed was both strain and mycotoxin-concentration dependent. Therefore, a theoretical model was applied in order to select the most efficient strain to remove AFB₁ in a wide range of mycotoxin concentration. The results indicated that S. cerevisiae 08 and S. cerevisiae 01 strains were the most efficient microorganisms in the mycotoxin removal. Viability on simulated salivary and gastrointestinal conditions was investigated and S. cerevisiae 08 strain showed the best results, achieving 98% of total survival whereas S. cerevisiae 01 reached only 75%. Autoaggregation and coaggregation assays showed S. cerevisiae 08 as the most appropriate strain, mainly because it was the unique strain able to coaggregate with the four bacterial pathogens assayed. Consequently, S. cerevisiae 08 is the best candidate for future in vivo studies useful to prevent aflatoxicosis. Further quantitative in vitro and in vivo studies are required to evaluate the real impact of yeast-binding activity on the bioavailability of AFB₁ in poultry. However, this study could be useful in selecting efficient strains in terms of AFB₁ binding and provide an important contribution to research into microorganisms with potential probiotic effects on the host.     

基于我国人群胃肠消化特征的土壤中As的人体可给性研究

基于我国人群胃肠消化特征,采用医学配方模拟胃肠消化方法测试了来自大连、湖南和广西的13个受重金属污染土壤中As的人体可给性,分析了土壤理化参数与可给性的相关关系及提取液中酶、胃肠液pH值、提取时间对As的人体可给性的影响.结果表明,医学配方可给性测试中,供试土样在胃、肠阶段As的人体可给性分别为5.03%~44.54%和10.77%~51.46%,平均值为18.08%、29.32%.胃阶段As的可给性浓度与土壤中总As含量w（TAs）、总P含量w（TP）极显著正相关,与总Al含量w（TAl）、土壤pH值、总有机质含量w（TOM）显著相关;肠阶段As的可给性浓度与土壤中w（TAs）、胃阶段As的可给性浓度、w（TP）极显著相关,与土壤pH值、w（TAl）和w（TOM）显著相关.胃阶段提取液中的胃蛋白酶显著降低了As的可给性,而肠阶段添加胰蛋白酶As的可给性没有明显变化.胃、肠阶段分别在pH值为0.9和5.0时可给性最大,0.9和5.0可分别作为土壤As在可给性测试过程中模拟胃肠液的pH值.胃、肠阶段在提取时间分别为1.0h、4.0h时可给性达到最大,且之后基本不变,1.0h、4.0h可作为模拟测试As在胃肠中可给性的提取时间.研究结果表明开展基于我国人群胃肠消化特征的土壤重金属人体可给性测试方法具有重要意义.     

上消化道出血的常见诱因分析及护理对策

本文对上消化道出血的常见诱因进行了分析,并对临床护理方法进行了实践探讨,以求对上消化道出血的护理工作提供参考.     

Miscible fluid displacement stability in unconfined porous media:: Two-dimensional flow experiments and simulations

In situ flushing groundwater remediation technologies, such as cosolvent flushing, rely on the stability of the interface between the resident and displacing fluids for efficient removal of contaminants. Contrasts in density and viscosity between the resident and displacing fluids can adversely affect the stability of the displacement front. Petroleum engineers have developed techniques to describe these types of processes; however, their findings do not necessarily translate directly to aquifer remediation. The purpose of this laboratory study was to investigate how density and viscosity contrasts affected cosolvent displacements in unconfined porous media characterized by the presence of a capillary fringe. Two-dimensional flow laboratory experiments, which were partially scaled to a cosolvent flushing field experiment, were conducted to determine potential implications of flow instabilities in homogeneous sand packs. Numerical simulations were also conducted to investigate the differential impact of fluid property contrasts in unconfined and confined systems. The results from these experiments and simulations indicated that the presence of a capillary fringe was an important factor in the displacement efficiency. Buoyant forces can act to carry a lighter-than-water cosolvent preferentially into the capillary fringe during displacement of the resident groundwater. During subsequent water flooding, buoyancy forces can act to effectively trap the cosolvent in the capillary fringe, contributing to the inefficient removal of cosolvent from the aquifer.     

The solid-phase controls on the mobility of heavy metals at the Copper Cliff tailings area, Sudbury, Ontario, Canada

The Copper Cliff Tailings Disposal Area, located near Sudbury, Ontario, covers an area of approximately 2200 ha and constitutes more than 10% of the total area of all mine tailings in Canada. The area has been utilized since 1936, receiving sulphide-containing tailings from the Inco Sudbury operations. Field measurements of pore-gas oxygen and carbon dioxide in the vadose zone indicate that sulphide oxidation has progressed to depths of 1.6 m to 1.7 m within the tailings. The oxidation of sulphide minerals within the vadose zone, and the accompanying dissolution of carbonate and aluminosilicate minerals within these tailings releases SO₄, Fe(II) and other metals to the pore water. In the vadose and saturated zones, concentrations of Fe and Ni exceed 10100 mg/l and 2210 mg/l, respectively. These high concentrations of dissolved metals are attenuated by a series of precipitation, coprecipitation and adsorption reactions. The precipitation of secondary sulphate and hydroxide phases also create hardpan layers at or near the oxidation front. Geochemical modelling of the pore-water chemistry suggests that pH-buffering reactions are occurring within the shallow oxidized zones, and that secondary-phase precipitation is occurring at or near the underlying hardpan and transition zones. Mineralogical study of the tailings confirmed the presence of jarosite, gypsum and goethite within the shallow tailings, suggesting that these phases are controlling the dissolved concentrations of Fe, SO₄ and Ca. Extraction experiments conducted on the tailings solids indicate that the constituents contained in the water-soluble fraction of the shallow, weathered tailings are derived from the original pore water and the dissolution of highly soluble phases such as gypsum. The acid-leachable fraction of the weathered tailings accounts for up to 25% of the heavy metals, and the reducible fraction may contain up to 100% of the heavy metals within the shallow, weathered tailings. Based on the pore water profiles and the geochemistry of the tailings solids, a relative mobility scale of Fe=Mn=Ni=Co>Cd Zn>Cr=Pb>Cu can be determined.