盐度对模拟餐厨垃圾发酵液产聚羟基脂肪酸酯工艺的影响

利用餐厨垃圾发酵液生产聚羟基脂肪酸酯(PHA)可以在废物处理的同时实现有价资源回收。为探究发酵液中盐分对产PHA菌群富集过程的影响,以模拟餐厨垃圾发酵液为底物,研究了盐度存在下污泥理化性质、富集过程主要指标及菌群PHA合成能力等变化。结果表明,未经盐度富集的菌群易受到盐度抑制,在15 g·L~(-1)的盐度条件下,污泥PHA最大合成量可降至39.9%。富集过程中盐度的增加有利于污泥沉降性的提升,低盐度(5 g·L~(-1))下菌群分泌胞外聚合物量最多,达49.8 mg·g~(-1)(以VSS计),对菌群保护能力最强。不同盐度条件下的富集系统皆能保持较好的生态选择压力,但盐度对微生物生长的抑制随着浓度的增大而增强。经过盐度存在下长期富集后的污泥,在高盐度(10、15 g·L~(-1))底物条件下,仍能获得较高的PHA最大合成能力,但其较低的生长活性不利于最终PHA产量的提升,短期富集下,高盐度会抑制PHA的合成;而低盐度(5 g·L~(-1))有助于提高PHA合成能力,最高达50.5%。     

天然胶/公共网络/废胶粉互穿聚合物网络

通过互穿聚合物网络技术成功制备了天然橡胶/公共网络/废胶粉共轭三组分,并测定了力学性能和微观形态。结果表明:当A/B摩尔比为2/1、AB含量为4.5%、废胶粉粒径为60目、废胶粉含量为15%时,体系的力学性能最好,共轭三组分天然橡胶/公共网络/废胶粉体系的磨耗体积明显低于两组分天然橡胶/废胶粉体系的磨耗体积。界面共轭互穿改善了界面结合,可减少反复压缩过程中的相间摩擦生热和变形。     

聚合物/表面活性剂二元体系对油水界面性质的影响

文章应用界面张力仪、Zeta电位仪和表面黏弹性仪测定了聚合物、表面活性剂及其二元复合体系的质量浓度对油水界面性质的影响,并应用透射电镜观察了采出液的液膜结构。结果表明,随着聚合物质量浓度的增加,油水界面的界面剪切黏度值和界面张力值增大,颗粒表面Zeta电位的绝对值增大;随着表面活性剂质量浓度的增加,油水界面的界面剪切黏度变化幅度很小,但界面张力显著减小,颗粒表面Zeta电位绝对值增大;聚合物与表面活性剂复合能够形成稳定的聚合体,具有较大的界面剪切黏度值,较小的界面张力和较高的Zeta电位值;体系中聚合物、表面活性剂及水中悬浮物形成了类似"晶体"结构。     

温度对膜生物反应器运行特性及膜污染的影响

温度对膜生物反应器（MBR）污染物去除效果和膜污染速率都有很大的影响。采用两套相同的MBR蓑置在冬季运行,其中一套维持20℃的恒温,另一套水温与周围环境相同。对两套装置处理效果及膜污染速率进行对比,并通过反应器中溶解性微生物产物（SMF）、胞外聚合物（EPS）含量、污泥粒径分布扣膜面污染物的比较,分析温度对MBR运行的影响。研究结果表明膜对污染物的截留能有效补偿低温时微生物作用的不足,因此低温对出水水质并没有显著的影响。此外,低温时虽然SMP和EPS的释放增加,但并没有引起膜污来的加剧。相反地,低温时污泥粒径较高温时小,而粒径较大的颗粒更易沉积于膜表面,因此低温时膜面固体物质含量较低,膜污染速率反而比高温时低。     

Fenton氧化破解剩余污泥中的胞外聚合物

利用Fenton试剂的强氧化性破解剩余污泥中的胞外聚合物（EPS）,通过释放出的多聚糖、蛋白质浓度以及SCOD的变化表征EPS的破解程度,旨在找出Fenton氧化破解EPS的适宜反应条件．结果表明,pH = 2.5,反应时间90 min,H₂O₂/Fe²⁺（质量比）= 8∶1,温度65～70℃为适宜反应条件．该条件下经Fenton氧化,污泥上清液中的SCOD、多聚糖和蛋白质浓度分别由45.88、 10.96和11.99 mg·L^-1增加到684.93、 382.17和302.62 mg·L^-1;污泥颗粒平均粒径和中值粒径分别由供试污泥的838.89 μm和859.20 μm减小到137.22 μm和148.69 μm．Fenton氧化可以有效破解污泥中的EPS,提高污泥的无机化程度,有利于污泥的减量化和资源化．     

泥水预分离MBR膜污染缓减效能研究

通过长期运行实验,进行了泥水预分离膜生物反应器（sludge/water pre-separation membrane bioreactor, S/W-MBR）与传统淹没式膜生物反应器（submerged membrane bioreactor, SMBR）对比研究,考察了污泥浓度、胞外聚合物含量（extracellular polymeric substances, EPS）及过膜阻力（trans-membrane pressure, TMP）随运行时间的变化规律及其对膜污染的缓减作用.结果表明,S/W-MBR与SMBR生物区的污泥浓度基本一致,而S/W-MBR膜区的污泥浓度较SMBR有显著降低.两者生物区的EPS含量均随运行时间的延长而增加,而S/W-MBR膜区的单位质量污泥的EPS含量始终保持在15 mg/g左右的较低水平.S/W-MBR比SMBR具有更好的缓减膜污染能力,在近90d的连续运行过程中,前者的膜组件仅需清洗2次,后者的膜组件清洗了5次.     

基质种类对活性污泥絮体性状的影响

利用葡萄糖、淀粉、乙酸钠和苯酚4种典型基质,分别在4个相同的序批式反应器(Sequencing Batch Reactor,SBR)中培养活性污泥,并研究了基质种类对活性污泥絮体性状的影响.结果表明,以葡萄糖为底物培养的活性污泥胞外多糖含量最少,而苯酚所培养的活性污泥胞外蛋白质最多;从形成的EPS总量来看,苯酚最多,乙酸钠次之,葡萄糖和淀粉较少.不同基质培养的污泥Zeta电位也有一定差别,这是由EPS中多糖和蛋白质的比例不同造成的.红外分析表明,4种基质培养的污泥EPS中的主要基团较为相似,羧基、醇羟基、羧酸、酰胺和多聚糖均是EPS中的主要基团.此外,进水基质对活性污泥絮体的粒度分布及分形结构也有重要影响.     

A novel aminated polymeric adsorbent for removing refractory dissolved organic matter from landfill leachate treatment plant

Refractory dissolved organic matter (DOM) from landfill leachate treatment plant was with high dissolved organic carbon (DOC) content. An aminated polymeric adsorbent NDA-8 with tertiary amino groups and sufficient mesopore was synthesized, which exhibited high adsorption capacity to the DOM (raw water after coagulation). Resin NDA-8 performed better in the uptake of the DOM than resin DAX-8 and A100. Electrostatic attraction was considered as the decisive interaction between the adsorbent and adsorbate. Special attention was paid to the correlation between porous structure and adsorption capacity. The mesopore of NDA-8 played a crucial role during uptake of the DOM. In general, resin in chloride form performed a higher removal rate of DOC. According to the column adsorption test, total adsorption capacity of NDA-8 was calculated to 52.28 mg DOC/mL wet resin. 0.2 mol/L sodium hydroxide solution could regenerate the adsorbent efficiently.     

Synthesis, characterization, and adsorption performance of Pb（Ⅱ）-imprinted polymer in nano-TiO2 matrix

Surface ion-imprinted in combination with sol-gel process was applied to synthesis a new Pb(II)-imprinted polymer for selective separation and enrichment of trace Pb(II) from aqueous solution. The prepared material was characterized by using the infrared spectra, X-ray di ractometer, and scanning electron microscopy. The batch experiments were conducted to study the optimal adsorption condition of adsorption trace Pb(II) from aqueous solutions on Pb(II)-imprinted polymer. The equilibrium was achieved in approximately 4.0 h, and the experimental kinetic data were fitted the pseudo second-order model better. The maximum adsorption capacity was 22.7 mg/g, and the Langmuir equation fitted the adsorption isotherm data. The results of selectivity experiment showed that selectively adsorbed rate of Pb(II) on Pb(II)-imprinted polymer was higher than all other studied ions. Desorption conditions of the adsorbed Pb(II) from the Pb(II)-imprinted polymer were also studied in batch experiments. The prepared Pb(II)-imprinted polymer was shown to be promising for the separation and enrichment of trace Pb(II) from water samples. The adsorption and desorption mechanisms were proposed.