Chemical characteristics of aerosols and trace gas distribution over North and Central India

A field campaign on aerosol chemical properties and trace gases measurements was carried out along the Delhi-Hyderabad-Delhi road corridor (spanning about 3,200 km) in India, during February 1-29, 2004. Aerosol particles were collected on quartz and cellulose filters using high volume (PM(10)) sampler at various locations along the route (i.e., urban, semi-urban, rural, and forest areas) and have been characterized for major cations (Na(+), Ca(2+), Mg(2+), K(+), and NH (4) (+)), anions (Cl(-), NO (3)(-), and SO (4)(2-)), and heavy metals (Cu, Cd, Fe, Zn, Mn, and Pb). Simultaneously, we measured NO(2) and SO(2) gases. These species show large spatial and temporal variations. The ambient PM(10) concentration has been observed to be the highest (55 ± 4 μg m(-3)) near semi-urban areas followed by forest areas (48 ± 2 μg m(-3)) and in rural areas (44 ± 22 μg m(-3)). The concentrations of NO( x ) (NO(2)+NO) and SO(2) ranged from 16 to 69 μg m(-3) and 4 to 11 μg m(-3), respectively. Among anions, NO(3)(-) and SO(4) (2-) are the major constituents of PM(10). The urban and semi-urban sites showed enhanced concentrations of Fe, Zn, Mn, Cd, and Pb. This study provide information about atmospheric concentrations of various species in the northern to central India, which may be important for policy makers to better understand the air quality of the region.     

Chemical compositions and sources of atmospheric PM10 in heating, non-heating and sand periods at a coal-based city in northeastern China

Mass concentrations and chemical components (18 elements, 9 ions, organic carbon [OC] and elemental carbon [EC]) in atmospheric PM(10) were measured at five sites in Fushun during heating, non-heating and sand periods in 2006-2007. PM(10) mass concentrations varied from 62.0 to 226.3 μg m(-3), with 21% of the total samples' mass concentrations exceeding the Chinese national secondary standard value of 150 μg m(-3), mainly concentrated in heating and sand periods. Crustal elements, trace elements, water-soluble ions, OC and EC represented 20-47%, 2-9%, 13-34%, 15-34% and 13-25% of the particulate matter mass concentrations, respectively. OC and crustal elements exhibited the highest mass percentages, at 27-34% and 30-47% during heating and sand period. Local agricultural residuals burning may contribute to EC and ion concentrations, as shown by ion temporal variation and OC and EC correlation analysis. Heavy metals (Cr, Ni, Zn, Cu and Mn) from coal combustion and industrial processes should be paid attention to in heating and sand periods. The anion/cation ratios exhibited their highest values for the background site with the influence of stationary sources on its upper wind direction during the sand period. Secondary organic carbon were 1.6-21.7, 1.5-23.0, 0.4-17.0, 0.2-33.0 and 0.2-21.1 μg m(-3), accounting for 20-77%, 44-88%, 4-77%, 8-69% and 4-73% of OC for the five sampling sites ZQ, DZ, XH, WH and SK, respectively. From the temporal and spatial variation analysis of major species, coal combustion, agricultural residual burning and industrial emission including dust re-suspended from raw material storage piles were important sources for atmospheric PM(10) in Fushun at heating, non-heating and sand periods, respectively. It was confirmed by principal component analysis that coal combustion, vehicle emission, industrial activities, soil dust, cement and construction dust and biomass burning were the main sources for PM(10) in this coal-based city.     

Is PM10 mass measurement a reliable index for air quality assessment? An environmental study in a geographical area of north-eastern Italy

The aim of this study was to measure the concentration of some metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Ti) in PM(10) samples collected in one urban and one industrial site and to assess that PM(10) total mass measurement may be not sufficient as air quality index due to its complex composition. Metals were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) and differential pulsed anodic stripping voltammetry (DPASV). The measured concentrations were used to calculate the content of metals in the PM(10) total mass, and to estimate the enrichment factors and the correlations between PM(10), metal concentrations and meteorological data for the two sites. The mean PM10 concentration during the sampling period in the urban site exceeded the annual European Union (EU) standard (40 microg/m(3)) and, for some sampling days, the daily EU standard (50 microg/m(3)) was also exceeded. In opposite, both EU standards were never exceeded in the industrial site. The overall metal content was nearly double in the industrial site compared to the urban one, and the mean Ni concentration exceeded the EU annual limit value (10 ng/m(3)). The metals with the highest enrichment factor were Cd, Cu, Ni and Pb for both sites, suggesting a dominant anthropogenic source for these metals. Metal concentrations were very low and typical of rural background during Christmas holidays, when factories were closed. PM(10) total mass measurement is not a sufficient air quality index since the metal content of PM(10) is not related to its total mass, especially in sites with industrial activities. This measurement should be associated with the analysis of toxic metals.     

Assessment of particulate matter in the urban atmosphere: size distribution, metal composition and source characterization using principal component analysis

In this study, the size distribution of airborne particles and related heavy metals Co, Cd, Sn, Cu, Ni, Cr, Pb and V in two urban areas in Istanbul: Yenibosna and Goztepe, were examined. The different inhalable particles were collected by using a cascade impactor in eight size fractions (<0.4 μm, 0.4-0.7 μm, 1.1-2.1 μm, 2.1-3.3 μm, 3.3-4.7 μm, 4.7-5.8 μm, 5.8-9 μm and >9 μm) for six months at each station. Samples were collected on glass fiber filters and filters were extracted and analyzed using ICP-MS. Log-normal distributions showed that the particles collected at the Yenibosna site have a smaller size compared to the Goztepe samples and the size distribution of PM was represented the best by the tri-modal. The average total particle concentrations and standard deviations were obtained as 67.7 ± 17.0 μg m(-3) and 82.1 ± 21.2 μg m(-3), at the Yenibosna and G?ztepe sites, respectively. The higher metal rate in fine and medium coarse PM showed that the anthropogenic sources were the most significant pollutant source. Principal component analysis identified five components for PM namely traffic, road dust, coal and fuel oil combustion, and industrial.     

Spatial and temporal variations in inhalable CuZnPb aerosols within the Mexico City pollution plume

We report on the CuPbZn content of PM10 and PM2.5 samples collected from three sites (urban T0, suburban T1 and rural T2) during the Mexico City MILAGRO campaign of March 2006. Daytime city centre concentrations of summation operator CuZnPb(PM10) were much higher (T0 > 450 ng m(-3)) than at the suburban site (T1 < 200 ng m(-3)). Rural site (T2) summation operator CuZnPb(PM10) concentrations exceeded 50 ng m(-3) when influenced by the megacity plume but dropped to 10 ng m(-3) during clean northerly winds. Nocturnal metal concentrations more than doubled at T0, as pollutants became trapped in the nightly inversion layer, but decreased at the rural site. Transient spikes in concentrations of different metals, e.g. a "copper event" at T0 (CuPM10 281 ng m(-3)) and "zinc event" at T1 (ZnPM10 1481 ng m(-3)) on the night of March 7-8, demonstrate how industrial pollution sources produce localised chemical inhomogeneities in the city atmosphere. Most metal aerosols are <2.5 microm and SEM study demonstrates the dominance of Fe, Ti, Ba, Cu, Pb and Zn (and lesser Sn, Mo, Sb, W, Ni, V, As, Bi) in metalliferous particles that have shapes including spherical condensates, efflorescent CuZnClS particles, cindery Zn, and Cu wire. Metal aerosol concentrations do not change in concert with PM10 mass, which is more influenced by wind resuspension than industrial emissions. Metalliferous particles can induce cell damage, and PM composition is probably more important than PM mass, with respect to negative health effects, so that better monitoring and control of industrial emissions would likely produce significant improvements in air quality.     

Aerosol size distribution and mass concentration measurements in various cities of Pakistan

During March and April 2010 aerosol inventories from four large cities in Pakistan were assessed in terms of particle size distributions (N), mass (M) concentrations, and particulate matter (PM) concentrations. These M and PM concentrations were obtained for Karachi, Lahore, Rawalpindi, and Peshawar from N concentrations using a native algorithm based on the Grimm model 1.109 dust monitor. The results have confirmed high N, M and PM concentrations in all four cities. They also revealed major contributions to the aerosol concentrations from the re-suspension of road dust, from sea salt aerosols, and from vehicular and industrial emissions. During the study period the 24 hour average PM(10) concentrations for three sites in Karachi were found to be 461 μg m(-3), 270 μg m(-3), and 88 μg m(-3), while the average values for Lahore, Rawalpindi and Peshawar were 198 μg m(-3), 448 μg m(-3), and 540 μg m(-3), respectively. The corresponding 24 hour average PM(2.5) concentrations were 185 μg m(-3), 151 μg m(-3), and 60 μg m(-3) for the three sites in Karachi, and 91 μg m(-3), 140 μg m(-3), and 160 μg m(-3) for Lahore, Rawalpindi and Peshawar, respectively. The low PM(2.5)/PM(10) ratios revealed a high proportion of coarser particles, which are likely to have originated from (a) traffic, (b) other combustion sources, and (c) the re-suspension of road dust. Our calculated 24 hour averaged PM(10) and PM(2.5) concentrations at all sampling points were between 2 and 10 times higher than the maximum PM concentrations recommended by the WHO guidelines. The aerosol samples collected were analyzed for crustal elements (Al, Fe, Si, Mg, Ca) and trace elements (B, Ba, Cr, Cu, K, Na, Mn, Ni, P, Pb, S, Sr, Cd, Ti, Zn and Zr). The averaged concentrations for crustal elements ranged from 1.02 ± 0.76 μg m(-3) for Si at the Sea View location in Karachi to 74.96 ± 7.39 μg m(-3) for Ca in Rawalpindi, and averaged concentrations for trace elements varied from 7.0 ± 0.75 ng m(-3) for B from the SUPARCO location in Karachi to 17.84 ± 0.30 μg m(-3) for Na at the M. A. Jinnah Road location, also in Karachi.     

Particle-bound polycyclic aromatic hydrocarbons in an urban, industrial and rural area in the western Mediterranean

Particle-bound PAHs were measured at three sites in southeastern Spain (an urban background location, a suburban-industrial site in the vicinity of two cement plants and a rural area) in order to investigate the influence of the type of location on PAH concentrations. A clear influence of cement production on particulate PAH levels could not be established since for the urban background and suburban-industrial sites the average concentrations of total PAHs in the PM2.5 fraction were very similar (1.085 and 1.151 ng m(-3), respectively), with benzo[b+k]fluoranthene and chrysene as the predominant compounds. Diagnostic ratios, used to identify PAH emission sources, pointed to traffic as the main source of particulate PAH at both locations. As expected, PAH levels at the rural site were significantly lower (0.408 ng m(-3) in the PM10 fraction) due to increasing distance from the emission sources. PAH seasonal variations at the urban background and suburban-industrial sites were the same as reported in many previous studies. Average winter to summer ratios for total PAHs were 4.4 and 4.9 for the urban background and industrial sites, in that order. This seasonal cycle could be partially explained by the higher temperature and solar radiation during summer enhancing PAH evaporation from the particulate phase and PAH photochemical degradation, respectively. The study of PAH distribution between the fine and coarse fraction at the urban site revealed that on average around 80% of total PAHs were associated with fine particles.     

Heavy metal bioaccumulation by the bryophyte Scleropodium purum at three French sites under various influences: rural conditions, traffic, and industry

An active biomonitoring of the heavy metals pollution experiment was undertaken by means of the bryophyte species Scleropodium purum transplanted at three different sites exposed to rural, traffic, or industrial influences. Concentrations of about 40 elements in S. purum were determined by instrumental neutron activation analysis and inductively coupled plasma mass spectrometry. Accumulation rates of heavy metals were determined in the three sites. These accumulation rates in polluted sites were matched together and also to those recorded at the rural site. The changes of the accumulation rate of heavy metals in S. purum versus their concentrations in PM₁₀ particles simultaneously collected above show some different accumulation properties of S. purum according to elements and sites. S. purum has a weak efficiency in the three sites to accumulate elements like V, Cr, Cu, Zn, As, Se, Sb, and Pb originating from atmospheric hot sources generally enriched in particulates matter (PM₁₀), whereas it is particularly high for Br, Th, and Rb. For other elements, Co, La, Ce, and Hf, and rare earth elements, Fe, Sr, Nb, Ti, Al, and Sc, the collection efficiency by S. purum is intermediate. In the industrial site Dunkerque, a magnification of the collection efficiency by S. purum for elements originating from steel and aluminum productions and petroleum refinement suggests that these metals could be enriched in coarse particles with a better accumulation by the bryophyte with respect to PM10.     

Evaluation of levels, sources and distribution of toxic elements in PM10 in a suburban industrial region, Rio de Janeiro, Brazil

The Oswaldo Cruz Foundation Campus (FIOCRUZ), in a suburban region of the city of Rio de Janeiro, was selected as a case study to assess the pollution released from vehicle and industrial facilities in Basin III, the most polluted area of the city. Concentrations of particulate matter (PM10) and trace metals in airborne particles were determined in an intensive field campaign. The samplings were performed every six days for 24 h periods, using a PM10 high volume sampler, from September 2004 to August 2005. PM10 mass concentrations were determined gravimetrically and the metals by ICP-OES. For PM10, the arithmetic mean for the period is 169 ± 42 μg m⁻³ which is 3.4 times the national recommended standard of 50 μg m⁻³. Additionally, 51% of the samplings exceeded the recommended 24 h limit of 150 μg m⁻³. Ca, Mg, Fe, Zn and Al were the metals that presented the higher concentrations. The correlation matrix gave two main clusters and three significant principal components (PC). Both PC1 and PC2 are associated to crustal, vehicular and industrial emissions while PC3 is mainly associated to geological material. Enrichment factors for Zn, Cu, Cd and Pb indicate that for these elements, anthropic sources prevail over natural inputs. PM10 levels showed a good correlation with hospital admissions for respiratory diseases in children and elderly people.     

Characterization of PM10 and PM2.5 and associated heavy metals at the crossroads and urban background site in Zabrze, Upper Silesia, Poland, during the smog episodes

The concentrations of seven heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, and Pb) associated with PM10 and PM2.5 at the crossroads and the background sites have been studied in Zabrze, Poland, during smog episodes. Although the background level was unusually elevated due to both high particulate emission from the industrial and municipal sources and smog favorable meteorological conditions, significant increase of the concentration of PM2.5 and PM10 as well as associated heavy metals in the roadside air compared to the urban background has been documented. The average daily difference between the roadside and corresponding urban background aerosol concentration was equal to 39.5 μg m^???3 for PM10 and 41.2 μg m^???3 for PM2.5. The highest levels of the studied metals in Zabrze appeared for iron carried by PM10 particles: 1,706 (background) and 28,557 ng m^???3 (crossroads). The lowest concentration level (in PM10) has been found for cadmium: 7 and 77 ng m^???3 in the background and crossroads site, respectively. Also the concentrations of heavy metals carried by the fine particles (PM2.5) were very high in Zabrze during the smog episodes. Concentrations of all studied metals associated with PM10 increased at the roadside compared to the background about ten times (one order) while metals contained in PM2.5 showed two to three times elevated concentrations (except Fe—five times and Cr—no increase).     

Abundance and sources of hydrophilic and hydrophobic water-soluble organic carbon at an urban site in Korea in summer

In this study, the characteristics of total water-soluble organic carbon (WSOC) and isolated WSOC fractions were examined to gain a better understanding of the pathway of organic aerosol production. 24 h PM(2.5) samples were collected during the summer (July 28-August 28, 2009) at an urban site in Korea. A glass column filled with XAD7HP resin was used to separate the filtered extracts into hydrophilic (WSOC(HPI)) and hydrophobic (WSOC(HPO)) fractions. The origins of air mass pathways arriving at the sampling site were mostly classified into three types, those originating over the East Sea of Korea that passed over the eastern inland urban and industrial regions (type I); those from the marine (western/southwestern/southern marine) and passed over the national industrial complex regions (type II); and those from northeastern China that passed through North Korea and metropolitan areas of South Korea (type III). Measurements showed an increase in the average WSOC fraction of total OC from the type II to III air mass (53 to 64%) periods. Also, higher SO(4)(2-)/SO(x) (=SO(2) + SO(4)(2-)) was observed in the type III air mass (0.70) than those in the types I (0.49) and II (0.43). According to the average values of WSOC/OC and SO(4)(2-)/SO(x), measurements suggest that the aerosols collected during the type III air mass period were more aged or photo-chemically processed than those during the types I and II air mass periods. The relationship between the SO(4)(2-)/SO(x) and WSOC/OC (R(2) = 0.64) suggests that a significant fraction of the observed WSOC at the site could be formed by an oxidation process similar to SO(4)(2-) aerosols, probably the oxidation process using OH radicals, or in-cloud processing. The photochemical production of WSOC(HPO) was also observed to significantly contribute to the total OC.     

Levels and chemical composition of PM in a city near a large Cu-smelter in Spain

A long-term series (2001-2008) of chemical analysis of atmospheric particulate matter (PM(10) and PM(2.5)) collected in the city of Huelva (SW Spain) is considered in this study. The impact of emission plumes from one of the largest Cu-smelters in the world on air quality in the city of Huelva is evidenced by the high daily and hourly levels of As, other potentially toxic elements (e.g. Cu, Zn, Cd, Se, Bi, and Pb) in particulate matter, as well as the high levels of some gaseous pollutants (NO(2) and SO(2)). Mean arsenic levels in the PM10 fraction were higher than the target value set by European Directive 2004/107/EC (6 ngAs m(-3)) for 1(st) January 2013. Hourly peak concentrations of As and other metals and elements (Zn, Cu, P and Se) analyzed by PIXE can reach maximum hourly levels as high as 326 ngAs m(-3), 506 ngZn m(-3), 345 ngCu m(-3), 778 ngP m(-3) and 12 ngSe m(-3). The contribution of Cu-smelter emissions to ambient PM is quantified on an annual basis in 2.0-6.7 μg m(-3) and 1.8-4.2 μg m(-3) for PM(10) and PM(2.5), respectively. High resolution outputs of the HYSPLIT dispersion model show the geographical distribution of the As ambient levels into the emission plume, suggesting that the working regime of the Cu-smelter factory and the sea breeze circulation are the main factors controlling the impact of the Cu-smelter on the air quality of the city. The results of this work improve our understanding of the behaviour of industrial emission plumes and their impact on air quality of a city, where the population might be exposed to very high ambient concentrations of toxic metals during a few hours.     

Indoor and outdoor concentrations of fine particles, particle-bound PAHs and volatile organic compounds in Kaunas, Lithuania

This complex study presents indoor and outdoor levels of air-borne fine particles, particle-bound PAHs and VOCs at two urban locations in the city of Kaunas, Lithuania, and considers possible sources of pollution. Two sampling campaigns were performed in January-February and March-April 2009. The mean outdoor PM(2.5) concentration at Location 1 in winter was 34.5 ± 15.2 μg m(-3) while in spring it was 24.7 ± 12.2 μg m(-3); at Location 2 the corresponding values were 36.7 ± 21.7 and 22.4 ± 19.4 μg m(-3), respectively. In general there was little difference between the PM concentrations at Locations 1 and 2. PM(2.5) concentrations were lower during the spring sampling campaign. These PM concentrations were similar to those in many other European cities; however, the levels of most PAHs analysed were notably higher. The mean sum PAH concentrations at Locations 1 and 2 in the winter campaign were 75.1 ± 32.7 and 32.7 ± 11.8 ng m(-3), respectively. These differences are greater than expected from the difference in traffic intensity at the two sites, suggesting that there is another significant source of PAH emissions at Location 1 in addition to the traffic. The low observed indoor/outdoor (I/O) ratios indicate that PAH emissions at the locations studied arise primarily from outdoor sources. The buildings at both locations have old windows with wooden frames that are fairly permissive in terms of air circulation. VOC concentrations were mostly low and comparable to those reported from Sweden. The mean outdoor concentrations of VOC's were: 0.7 ± 0.2, 3.0 ± 0.8, 0.5 ± 0.2, 3.5 ± 0.3, and 0.2 ± 0.1 μg m(-3), for benzene, toluene, ethylbenzene, sum of m-, p-, o-xylenes, and naphthalene, respectively. Higher concentrations of VOCs were observed during the winter campaign, possibly due to slower dispersion, slower chemical transformations and/or the lengthy "cold start" period required by vehicles in the wintertime. A trajectory analysis showed that air masses coming from Eastern Europe carried significantly higher levels of PM(2.5) compared to masses from other regions, but the PAHs within the PM(2.5) are of local origin. It has been suggested that street dust, widely used for winter sanding activities in Eastern and Central European countries, may act not only as a source of PM, but also as source of particle-bound PAHs. Other potential sources include vehicle exhaust, domestic heating and long-range transport.     

Composition, seasonal variation, and sources of PM10 from world heritage site Taj Mahal, Agra

Air samples for PM(10) (dp?相似文献   

一次连续在线观测分析天津市细颗粒物污染特征

根据2005年的5月17日—5月23日GR IMM(1.109#)谱分析仪在线观测结果考察天津市细颗粒物浓度和质量浓度特征。观测期间,天津市颗粒物数浓度平均值为1 124 cm-3,粒径分布为0.25μm~0.60μm,98.5%粒子的粒径0.65μm。同期PM10日均质量浓度值为204μg/m3,ρ(PM2.5)为104μg/m3,ρ(PM1.0)为82.9μg/m3。ρ(PM1.0)/ρ(PM2.5)超过80%,粒径1μm超细颗粒物为天津城市大气颗粒物的主要成分。     

Aerosol chemical characteristics of an island site in the Bay of Bengal (Bhola-Bangladesh)

Aerosol constituents (elemental carbon, organic carbon, soluble ions including organic acids, and selected trace metals) were investigated from samples of a field campaign taking place at Bhola Island in the Bay of Bengal (Bangladesh). The campaign took place in the pre-monsoon season (May 2001) using low volume samplers. Carbonaceous material comprised the majority of the analysed components. The average concentrations of EC and OC were 2.8 and 4.6 microg m(-3), respectively. Oxalic acid was the most abundant dicarboxylic acid (average 268 ng m(-3)) followed by malonic and malic acid. The contribution of carboxylic acids-carbon to organic carbon was 2.0%. Average concentrations observed for sulfate and nitrate were 3.7 microg m(-3) and 1.5 microg m(-3). Two different types of aerosol were identified at the rural background site on Bhola Island during southerly synoptic flow by means of trajectory analysis: air masses were transported from the Bay of Bengal to the sampling site in all cases. However, during "Period 1" they experienced longer residence times over the Indian Ocean, while the "Period 2" trajectories came along the Indian coast or passed over the Indian continent. During Period 1 the concentration levels of soluble ions were a factor of 4-6 lower than during Period 2. The concentrations of EC, OC and K differed less than a factor of 1.5 between the two periods. The Period 1 aerosol showed similarities to the haze layers observed during winter-monsoon conditions south of India during the INDOEX experiment. Based on EC/TC and K/EC ratios we find that around 80% of the carbonaceous aerosol from Period 1 in Bhola is from fossil fuel and only around 50% from Period 2. Absolute concentrations of carbonaceous species, soluble ions and trace metals indicate that the background site on Bhola Island is affected by emissions from urbanized regions of Southeast Asia.     

An analysis of spatial and temporal properties of daily sulfate, nitrate and chloride concentrations at UK urban and rural sites

Daily measurements of sulfate, nitrate and chloride in PM(10) have been made at three geographically separated UK sites over a three year period. Chloride shows a clear seasonal pattern with highest concentrations in winter, whilst sulfate and nitrate both show highest concentrations in the spring, apparently related to weather patterns. Spatial variability of both sulfate and nitrate is low in comparison to temporal variations, with high correlations of both species between all three sites, London (North Kensington), Harwell and Belfast, despite a geographic separation of 510 km. Both SO/SO(2) and NO/NO(x) ratios are considerably higher in summer than winter, reflecting a greater oxidising capacity of the atmosphere. SO(4)(2-)/NO(3)(-) ratios are higher in summer than winter, suggesting that aqueous phase oxidation of SO(2), expected to be most important in the winter months is not appreciably influencing production of sulfate aerosol, although greater dissociation of ammonium nitrate in summer may also play a role. Regression of concentrations at London, North Kensington with those from the proximate rural site of Harwell is interpreted as showing a similar effect of regional transport at the two sites and a small influence of local formation in the urban atmosphere or primary emissions, averaging 0.46 microg m(-3) of nitrate and 0.22 microg m(-3) of sulfate.     

Local and regional air pollution in Ireland during an intensive aerosol measurement campaign

An intensive two month measurement campaign has been performed during a two year study of major component composition of urban PM10 and PM2.5 in Ireland (J. Yin, A. G. Allen, R. M. Harrison, S. G. Jennings, E. Wright, M. Fitzpatrick, T. Healy, E. Barry, D. Ceburnis and D. McCusker, Atmos. Res., 2005, 78(3-4), 149-165). Measurements included size-segregated mass, soluble ions, elemental carbon (EC) distributions, fine and coarse fraction organic carbon (OC) and major gases along with standard meteorological measurements. The study revealed that urban emissions in Ireland had mainly a local character and therefore were confined within a limited area of 20-30 km radius, without significantly affecting regional air quality. Gaseous measurements have shown that urban emissions in Ireland had clear, but fairly limited influence on the regional air quality due to favorable mixing conditions at higher wind speeds, in particular from the western sector. Size-segregated mass and chemical measurements revealed a clear demarcation size between accumulation and coarse modes at about 0.8 microm which was constant at all sites. Carbonaceous compounds at the urban site accounted for up to 90% of the particle mass in a size range of 0.066-0.61 microm. Nss SO4(2-) concentrations in PM2.5 were only slightly higher at the urban site compared to the rural or coastal sites, while NO3- and NH4+ concentrations were similar at the urban and coastal sites, but were a factor of 2 to 3 higher than at the rural site. OC was highly variable between the sites and revealed clear seasonal differences. Natural or biogenic OC component accounted for <10% in winter and up to 30% in summer of the PM2.5 OC at urban sites. A contribution of biogenic OC component to PM2.5 OC mass at rural site was dominant.     

乌鲁木齐市可吸入颗粒物污染水平及其与气象因素的相关性分析

为了解可吸入颗粒物污染水平与气象因素之间的关系,从2008年9月—2010年2月采集乌鲁木齐市可吸入颗粒物样品,并对其随时间的变化特征及其与气象因素之间的相关性进行了统计分析。结果表明,采样时间内可吸入颗粒物中PM2.5和PM2.5-10的质量浓度的范围分别为38.2~468.7μg/m3和20.8~243.1μg/m3,平均浓度分别为134.2μg/m3和69.2μg/m3。可吸入颗粒物同时受几种气象因素的影响,其浓度与温度、能见度、风速呈负相关,与湿度呈正相关。     

Source apportionment of PM10 and PM(2.5) at Tocopilla, Chile (22 degrees 05' S, 70 degrees 12' W)

Tocopilla is located on the coast of Northern Chile, within an arid region that extends from 30 degrees S to the border with Perú. The major industrial activities are related to the copper mining industry. A measurement campaign was conducted during March and April 2006 to determine ambient PM10 and PM(2.5) concentrations in the city. The results showed significantly higher PM10 concentrations in the southern part of the city (117 microg/m3) compared with 79 and 80 (microg/m3) in the central and northern sites. By contrast, ambient PM2.5 concentrations had a more uniform spatial distribution across the city, around 20 (microg/m3). In order to conduct a source apportionment, daily PM10 and PM(2.5) samples were analyzed for elements by XRF. EPA's Positive Matrix Factorization software was used to interpret the results of the chemical compositions. The major source contributing to PM(2.5) at sites 1, 2 and 3, respectively are: (a) sulfates, with approximately 50% of PM2.5 concentrations at the three sites; (b) fugitive emissions from fertilizer storage and handling, with 16%, 21% and 10%; (c) Coal and residual oil combustion, with 15%, 15% and 4%; (d) Sea salt, 5%, 6% and 16%; (e) Copper ore processing, 4%, 5% and 15%; and (f) a mixed dust source with 11%, 7% and 4%. Results for PM10--at sites 1, 2 and 3, respectively--show that the major contributors are: (a) sea salt source with 36%, 32% and 36% of the PM10 concentration; (b) copper processing emissions mixed with airborne soil dust with 6.6%, 11.5% and 41%; (c) sulfates with 31%, 31% and 12%; (d) a mixed dust source with 16%, 12% and 10%, and (e) the fertilizer stockpile emissions, with 11%, 14% and 2% of the PM10 concentration. The high natural background of PM10 implies that major reductions in anthropogenic emissions of PM10 and SO2 would be required to attain ambient air quality standards for PM10; those reductions would curb down ambient PM(2.5) concentrations as well.