活性炭负载Fe^3＋催化H2O2氧化邻苯二甲酸二甲酯

将Fe3＋负载在活性炭上制得载铁催化剂Fe/AC,并研究了该催化剂对邻苯二甲酸二甲酯（DMP）的催化降解性能。通过正交实验和单因素实验,探讨了催化剂投加量、H2O2投加量、溶液pH值和反应温度对水中DMP降解率的影响,同时对DMP矿化度进行了分析。实验结果表明,制得的载铁催化剂具有较高的催化活性;降解效果的影响顺序是反应温度〉催化剂投加量〉H2O2投加量〉溶液pH值;在反应温度为80℃、催化剂投加量为4 g/L、H2O2投加量为20 mL/L和溶液pH值为3的条件下反应120 min后,质量浓度为10 mg/L的DMP降解率最高可达97.73%;在优化的实验条件下反应150 min,DMP矿化度可达62.73%;催化剂反复使用5次仍具有较好的催化活性,DMP降解率仍可达到77%以上;反应过程中溶液Fe3＋浓度的变化维持在1.07 mg/L左右,且可推测催化降解DMP主要是由非均相和均相催化氧化反应共同作用的。     

Carbofuran degradation by the application of MW-assisted H₂O₂ process

Carbofuran removal performance of a microwave (MW)-assisted H?O? system under different MW-power levels (300-900 W) was investigated. Batch experiments were conducted at 100 mg/L carbofuran concentration using a modified-MW reactor with 2450 MHz of fixed frequency. As a precursor, control experiments were carried out with H?O? alone, MW alone and conventional heating (CH). A maximum carbofuran removal of 14 % was observed in both H?O? alone and CH systems. On the other hand, only 2 % removal was observed in the MW alone system irrespective of the operation-mode, i.e. continuous or pulsed. The combination of MW and H?O? produced 100 % carbofuran removal in all the MW-assisted experiments. The MW-assisted system operated under continuous-mode and at 750 W has showed rapid carbofuran degradation, i.e. 30 sec, with the highest first-order removal rate constant of 25.82/min. However, 97 % carbon oxygen demand (COD) removal was observed in the same system only after 30 min. On the other hand, 100 % carbofuran removal and 49 % COD removal were observed in the pulsed-mode MW-assisted H?O? system after 10 and 30 min, respectively. Carbofuran mineralization in the system was evidenced by the formation of ammonium and nitrate, and carbofuran intermediates.     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl(-) increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl(-) at total mineralization was detected when initial diuron concentration was 13.8 mg L(-1). For N species, the final concentrations of NO3(-) and NH4+ after 60 min of reaction time were 0.28 and 0.19 mg L(-1), respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na2CO3, additive NaHCO3 and additive H2O2 were all advantageous to improve the degradation efficiency of diuron.     

Photocatalytic removal of fenitrothion in pure and natural waters by photo-Fenton reaction

The photocatalytic removal kinetics of fenitrothion at a concentration of 0.5mgl(-1) in pure and natural waters were investigated in Fe(III)/H2O2/UV-Vis, Fe(III)/UV-Vis and H2O2/UV-Vis oxidation systems, with respect to decreases in fenitrothion concentrations with irradiation time using a solar simulator. Fenitrothion concentrations were determined by HPLC analysis. Furthermore, total mineralization of fenitrothion in these systems was evaluated by monitoring the decreases in DOC concentrations with solar simulator irradiation time by TOC analysis. It was shown that the degradation rate of fenitrothion was much faster in the Fe(III)/H2O2/UV-Vis system than the Fe(III)/UV-Vis and H2O2/UV-Vis systems in both pure and river waters. Consequently, the mineralization rate of fenitrothion was much faster in the Fe(III)/H2O2/UV-Vis system than in the other two systems. The high *OH generation rate measured in the Fe(III)/H2O2/UV-Vis system was the key to faster degradation of fenitrothion. Increases in the concentrations of H2O2 and Fe led to better final degradation of fenitrothion. These results suggest that the photo-Fenton reaction (Fe(III)/H2O2/UV-Vis) system is likely to be an effective method for removing fenitrothion from contaminated natural waters.     

Degradation of clofibric acid in acidic aqueous medium by electro-Fenton and photoelectro-Fenton

Acidic aqueous solutions of clofibric acid (2-(4-chlorophenoxy)-2-methylpropionic acid), the bioactive metabolite of various lipid-regulating drugs, have been degraded by indirect electrooxidation methods such as electro-Fenton and photoelectro-Fenton with Fe(2+) as catalyst using an undivided electrolytic cell with a Pt anode and an O(2)-diffusion cathode able to electrogenerate H(2)O(2). At pH 3.0 about 80% of mineralization is achieved with the electro-Fenton method due to the efficient production of oxidant hydroxyl radical from Fenton's reaction between Fe(2+) and H(2)O(2), but stable Fe(3+) complexes are formed. The photoelectro-Fenton method favors the photodecomposition of these species under UVA irradiation, reaching more than 96% of decontamination. The mineralization current efficiency increases with rising metabolite concentration up to saturation and with decreasing current density. The photoelectro-Fenton method is then viable for treating acidic wastewaters containing this pollutant. Comparative degradation by anodic oxidation (without Fe(2+)) yields poor decontamination. Chloride ion is released during all degradation processes. The decay kinetics of clofibric acid always follows a pseudo-first-order reaction, with a similar rate constant in electro-Fenton and photoelectro-Fenton that increases with rising current density, but decreases at greater metabolite concentration. 4-Chlorophenol, 4-chlorocatechol, 4-chlororesorcinol, hydroquinone, p-benzoquinone and 1,2,4-benzenetriol, along with carboxylic acids such as 2-hydroxyisobutyric, tartronic, maleic, fumaric, formic and oxalic, are detected as intermediates. The ultimate product is oxalic acid, which forms very stable Fe(3+)-oxalato complexes under electro-Fenton conditions. These complexes are efficiently photodecarboxylated in photoelectro-Fenton under the action of UVA light.     

Photochemical degradation and mineralization of 4-chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Since the intermediate products of some compounds can be more toxic and/or refractory than the original compund itself, the development of innovative oxidation technologies which are capable of transforming such compounds into harmless end products, is gaining more importance every day. Advanced oxidation processes are one of these technologies. However, it is necessary to optimize the reaction conditions for these technologies in order to be cost-effective. OBJECTIVE: The main objectives of this study were to see if complete mineralization of 4-chlorophenol with AOPs was possible using low pressure mercury vapour lamps, to make a comparison of different AOPs, to observe the effect of the existence of other ions on degradation efficiency and to optimize reaction conditions. METHODS: In this study, photochemical advanced oxidation processes (AOPs) utilizing the combinations of UV, UV/H2O2 and UV/H2O2/Fe2+ (photo-Fenton process) were investigated in labscale experiments for the degradation and mineralization of 4-chlorophenol. Evaluations were based on the reduction of 4-chlorophenol and total organic carbon. The major parameters investigated were the initial 4-chlorophenol concentration, pH, hydrogen peroxide and iron doses and the effect of the presence of radical scavengers. RESULTS AND DISCUSSION: It was observed that the 4-chlorophenol degradation efficiency decreased with increasing concentration and was independent of the initial solution pH in the UV process. 4-chlorophenol oxidation efficiency for an initial concentration of 100 mgl(-1) was around 89% after 300 min of irradiation in the UV process and no mineralization was achieved. The efficiency increased to > 99% with the UV/H2O2 process in 60 min of irradiation, although mineralization efficiency was still around 75% after 300 min of reaction time. Although the H2O2/4-CP molar ratio was kept constant, increasing initial 4-chlorophenol concentration decreased the treatment efficiency. It was observed that basic pHs were favourable in the UV/H2O2 process. The results showed that the photo-Fenton process was the most effective treatment process under acidic conditions. Complete disappearance of 100 mgl(-1) of 4-chlorophenol was achieved in 2.5 min and almost complete mineralization (96%) was also possible after only 45 min of irradiation. The efficiency was negatively affected from H2O2 in the UV/H2O2 process and Fe2+ in the photo-Fenton process over a certain concentration. The highest negative effect was observed with solutions containing PO4 triple ions. Required reaction times for complete disappearance of 100 mgl(-1) 4-chlorophenol increased from 2.5 min for an ion-free solution to 30 min for solutions containing 100 mgl(-1) PO4 triple ion and from 45 min to more than 240 min for complete mineralization. The photodegradation of 4-chlorophenol was found to follow the first-order law. CONCLUSION: The results of this study showed that UV irradiation alone can degrade 4-CP, although at very slow rates, but cannot mineralize the compound. The addition of hydrogen peroxide to the system, the so-called UV/H2O2 process, significantly enhances the 4-CP degradation rate, but still requires relatively long reaction periods for complete mineralization. The photo-Fenton process, the combination of homogeneous systems of UV/H2O2/Fe2+ compounds, produces the highest photochemical elimination rate of 4-CP and complete mineralization is possible to achieve in quite shorter reaction periods when compared with the UV/H2O2 process. RECOMMENDATIONS AND OUTLOOK: It is more cost effective to use these processes for only purposes such as toxicity reduction, enhancement of biodegradability, decolorization and micropollutant removal. However the most important point is the optimization of the reaction conditions for the process of concern. In such a case, AOPs can be used in combination with a biological treatment systems as a pre- or post treatment unit providing the cheapest treatment option. The AOP applied, for instance, can be used for toxicity reduction and the biological unit for chemical oxygen demand (COD) removal.     

Degradation of calcium lignosulfonate using gamma-ray irradiation

Gamma-ray irradiation was proven to be a promising means for the removal of calcium lignosulfonate (CaLS). At a dose rate of 55Gy min(-1), over 90% of CaLS was mineralized to CO(2), H(2)O and sulfates within 3-d irradiation. The degradation of CaLS with the initial CaLS concentrations ranging from 40 to 200mg l(-1) followed zero-order kinetics at the dose rates of 16-150Gy min(-1). The zero-order degradation rate constant was functionally related with irradiation dose rate. Experiments performed with or without addition of radical scavengers demonstrated that the role of *OH was predominant in CaLS degradation and the reductive species made minor contributions to CaLS degradation. Addition of appropriate amounts of H(2)O(2) significantly enhanced the mineralization of CaLS, e.g., addition of 10mM H(2)O(2) at a dose rate of 55Gy min(-1) elevated the mineralization rate constant by five times. The addition of Fenton's reagent to irradiated CaLS solutions facilitated the degradation of CaLS, but no obviously synergistic effect was observed.     

负载TiO2/Fe3+的玻璃纤维反应器光催化苯酚

以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3+作为掺杂改性离子,形成了负载TiO2/Fe3+的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365～250 W光源照射下,pH为3～5,O2通入量1.0 L/(min.L),反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。     

Fenton试剂处理腐殖酸废水影响特性和降解动力学模型

研究了Fenton试剂降解腐殖酸废水的影响特性,并在理论分析反应过程的基础上建立动力学方程,同时根据实验进行动力学方程参数估算。研究表明,Fenton试剂通过氧化和混凝共同作用有效去除腐殖酸。在初始pH=4,40mmol/L FeSO4和160 mmol/L H2O2投量下,腐殖酸60 min氧化去除率、混凝去除率分别达到78.6%和11.5%,其初始氧化速率达到最大59.6 mg/(L.min)。腐殖酸的氧化降解动力学模型值与实验值吻合良好,说明采用该动力学模型能较好预测腐殖酸废水的氧化降解情况,且Fenton氧化降解腐殖酸的机理符合自由基的理论和实践。     

Mineralization of Reactive Black 5 in aqueous solution by basic oxygen furnace slag in the presence of hydrogen peroxide

Basic oxygen furnace slag (BOF slag) is a solid waste arisen from the steel making process. FeO is one of the major components of BOF slag. The FeO-containing property of BOF slag makes it possible to catalyze the Fenton reaction. Reactive Black 5 (RB5) dye is chosen as the target compound in this study. This study has investigated the catalytic performance of BOF slag on the Fenton reaction to decompose RB5 in aqueous solution. A first-order kinetic model with respect to TOC was adopted to explain the mineralization of RB5 by the H(2)O(2)/BOF slag process. The experimental results in this study suggested that dosage with 1.49 x 10(-4)M min(-1) H(2)O(2) and 12.5 g l(-1) BOF slag in the solution at pH 2 provided the optimal operation conditions for the mineralization of RB5 yielding a 51.2% treatment efficiency at 100 min reaction time, and complete decoloration can be achieved within 30 min reaction time. The H(2)O(2)/Fe(2+) ratio was then determined to be 6.06:1.     

铁炭微电解-H2O2法降解二甲基甲酰胺废水

采用铁炭微电解-H2O2法降解二甲基甲酰胺(DMF)废水,探讨了反应时间、pH、铁炭质量比(简写为Fe/C)以及H2O2投加量对DMF去除率的影响.结果表明:(1)当反应时间为60 min、pH为3、Fe/C为3:1时,DMF去除率为73.4％.(2)向反应体系中投加H2O2,DMF去除率明显提高.当H2O2投放量为0.20 mL/L时,DMF去除率达到95.2％.     

Degradation of 2,7-dichlorodibenzo-p-dioxin by Fe(3+)-H(2)O(2) mixed reagent

Fe(3+)-H(2)O(2) mixed reagent, but not Fe(2+)-H(2)O(2), was found to be capable of degrading 2,7-dichlorodibenzo-p-dioxin (DCDD). A reaction mixture of FeCl(3) (8 mM) and H(2)O(2) (1%) caused approximately 50% degradation within 6 h and >90% degradation within 24 h at 27 degrees C. Increasing the temperature remarkably stimulated degradation: at 70 degrees C, approximately 100% degradation was achieved within 15 min. When DCDD-treated model soil (5 micrograms/g) was conducted, approximately 100% of the DCDD was degraded within 30 min at 70 degrees C (both reagents were added every 10 min). These results suggest that Fe(3+)-H(2)O(2) mixed reagent may be a new tool for combating persistent environmental pollutants such as dioxins and polychlorinated biphenyls.     

Influences of metals on kinetics of methyl tert-butyl ether biodegradation by Ochrobactrum cytisi

The influence of zinc, manganese, and nickel on the degradation of MTBE (methyl tert-butyl ether), by an aerobic MTBE-degrading strain, Ochrobactrum cytisi, were investigated. The result showed that unlike previous findings, O. cytisi was able to degrade MTBE through direct metabolism when MTBE was present as the only carbon source. The degradation rate of MTBE was rapid, completed within 80 h. MTBE biodegradation by this strain was stimulated at low concentrations of Zn(2+) (1-5 mg l(-1)) and Mn(2+) (1-5 mg l(-1)) but inhibited at high concentrations of Zn(2+) (20 mg l(-1)) and Mn(2+) (20 mg l(-1)), and at low concentration of Ni(2+) (1-4 mg l(-1)). Kinetic parameters for MTBE degradation in the presence or absence of metals were obtained through nonlinear regression and a least-square minimization procedure. In all cases, a good agreement was achieved between kinetic simulations and experimental results.     

TS-1分子筛催化O3/H2O2氧化乙酸

研究了酸性条件下TS-1分子筛催化O3/H2O2体系(O3/H2O2/TS-1)对降解水中乙酸效率的影响,优化了相关工艺参数,并对其作用机理进行了分析。结果表明,在pH为2.8时,TS-1的加入能显著提高臭氧化的降解效率。优化工艺参数表明,当过氧化氢投加量为3 g/L,TS-1投加量为5 g/L时,O3/H2O2/TS-1体系对乙酸具有较高的降解率,60 min后O3/H2 O2/TS-1体系对乙酸(初始浓度为100 mg/L)的去除率达到了58.7%。当pH为0.8时,O3/H2 O2/TS-1体系对乙酸的去除率仅为19.8%,降解效果较差。定量化计算表明,O3/H2O2和O3/H2O2/TS-1的Rct分别为1.62×10-8和8.67×10-7。通过测定乙酸降解过程水样中过氧化氢和液相臭氧的浓度变化,推测了具体反应机理。由于此体系在酸性条件下对乙酸有较好的降解效果,拓宽了现有O3/H2O2体系的应用范围。     

Photocatalytic mineralization of glyphosate in a small-scale plug flow simulation reactor by UV/TiO2

The present work involves the photocatalytic mineralization of glyphosate on a plug flow reactor by UV/TiO(2). The effect of catalyst loading shows an optimal value (0.4 g L(-1)) which is necessary to mineralize glyphosate. The kinetic rate of glyphosate mineralization decreases with the increasing initial concentration of glyphosate, and the data can be described using the first-order model. An alkaline environment is conducive to glyphosate mineralization. The mineralization efficiency increases with elevated flow rate to 114 mL min(-1), which is followed by a decrease with a further increase in flow rate due to the reduction of the residence time. The presence of external oxidants (K(2)S(2)O(8), H(2)O(2) and KBrO(3)) and photosencitizer (humic acid) can significantly enhance glyphosate mineralization. Photocatalysis oxidation ability of the three studied oxidants decrease in the order of: S(2)O(8)(2-) > BrO(3)(-) > H(2)O(2). Finally, the Langmuir-Hinshelwood (L-H) model was used to rationalize the mechanisms of reactions occurring on TiO(2) surfaces and L-H model constants were also determined.     

O3/H2O2工艺降解1,2,4-三氯苯的优化设计

考察用不同的氧化剂降解1,2,4-三氯苯（TCB）,3种不同方法对TCB的去除效果存在较大差别,其处理效果依次为：H2O2〈O3〈O3/H2O2。采用响应面法优化O3/H2O2工艺降解TCB的条件。结果表明,TCB初始浓度和H2O2投加量对TCB去除效果影响较大。TCB的降解符合准一级反应动力学规律,最佳降解条件为TCB初始浓度0.3 mg/L,pH=8.13,H2O2投加量0.40 mmol/L,O3转化率75%。在此条件下,TCB的平均去除率为91.5%,与预测值93.1%吻合度较高。     

Comparison of fenton and photo-fenton processes for livestock wastewater treatment

In this study, the photochemical degradation of livestock wastewater was carried out by the Fenton and Photo-Fenton processes. The effects of pH, reaction time, the molar ratio of Fe(2 +)/H(2)O(2), and the Fe(2 +) dose were studied. The optimal conditions for the Fenton and Photo-Fenton processes were found to be at a pH of 4 and 5, an Fe(2 +) dose of 0.066 M and 0.01 M, a concentration of hydrogen peroxide of 0.2 M and 0.1 M, and a molar ratio (Fe(2 +)/H(2)O(2)) of 0.33 and 0.1, respectively. The optimal reaction times in the Fenton and Photo-Fenton processes were 60 min and 80 min, respectively. Under the optimal conditions of the Fenton and Photo-Fenton processes, the chemical oxygen demand (COD), color, and fecal coliform removal efficiencies were approximately 70--79, 70--85 and 96.0--99.4%, respectively.     

Destruction of organic pollutants in reusable wastewater using advanced oxidation technology

This work studied the destruction of various M-EDTA complexes and trace organic pollutants in treated reusable wastewater under advanced oxidation using UV irradiation and ozonation. Effect of dosage of hydrogen peroxide and acidity of reaction matrices on oxidation efficiencies were investigated. The rate constant of mineralization presents a decreasing trend as Fe(III)-EDTA > Fe(II)-EDTA > Al(III)-EDTA > Pb(II)-EDTA > Na(I)-EDTA > Zn(II)-EDTA > Cu(II)-EDTA. The mineralization efficiencies using ozone alone are 15%, 40% and 15% for the water samples after reverse osmosis (RO), microfiltration (MF) and superfiltration (SF) processes, respectively. The presence of hydrogen peroxide in photochemical reaction matrixes can effectively enhance the mineralization of organic carbon species. When 150 mg l(-1) of H2O2 was added in the effluents, the mineralization markedly increased to 80%, 92% and 89%, respectively.     

氧化-混凝法处理碱性高砷废水的实验研究

对碱性高砷废水的处理进行了研究 ,针对常规混凝法除砷的缺点提出了氧化 混凝工艺。结果表明 ,用氧化 混凝工艺除砷效果显著 ,废水经处理后砷含量低于 0 5mg/L ,符合国家排放标准。氧化 混凝除砷的最佳工艺条件为 :pH值为 6— 7,H2 O2 用量为 2 5 % ,氧化时间为 10min ,Fe2 (SO4) 3 用量为 2 5g/L ,PAM用量为 11 2 5mg/L。     

TS-1分子筛催化O_3/H_2O_2氧化乙酸

研究了酸性条件下TS-1分子筛催化O3/H2O2体系（O3/H2O2/TS-1）对降解水中乙酸效率的影响,优化了相关工艺参数,并对其作用机理进行了分析。结果表明,在pH为2.8时,TS-1的加入能显著提高臭氧化的降解效率。优化工艺参数表明,当过氧化氢投加量为3 g/L,TS-1投加量为5 g/L时,O3/H2O2/TS-1体系对乙酸具有较高的降解率,60 min后O3/H2 O2/TS-1体系对乙酸（初始浓度为100 mg/L）的去除率达到了58.7%。当pH为0.8时,O3/H2 O2/TS-1体系对乙酸的去除率仅为19.8%,降解效果较差。定量化计算表明,O3/H2O2和O3/H2O2/TS-1的Rct分别为1.62×10-8和8.67×10-7。通过测定乙酸降解过程水样中过氧化氢和液相臭氧的浓度变化,推测了具体反应机理。由于此体系在酸性条件下对乙酸有较好的降解效果,拓宽了现有O3/H2O2体系的应用范围。