Study of urban atmospheric pollution in Navarre (Northern Spain)

An ambient air quality study was undertaken in two cities (Pamplona and Alsasua) of the Province of Navarre in northern Spain from July 2001 to June 2004. The data were obtained from two urban monitoring sites. At both monitoring sites, ambient levels of ozone, NO_x, and SO₂ were measured. Simultaneously with levels of PM₁₀ measured at Alsasua (using a laser particle counter), PM₁₀ levels were also determined at Pamplona (using a beta attenuation monitor). Mean annual PM₁₀ concentrations in Pamplona and Alsasua reached 30 and 28 μg m⁻³, respectively. These concentrations are typical for urban background sites in Northern Spain. By using meteorological information and back trajectories, it was found that the number of exceedances of the daily PM₁₀ limit as well as the PM₁₀ temporal variation was highly influenced by air masses from North Africa. Although North African transport was observed on only 9% of the days, it contributed the highest observed PM₁₀ levels. Transport from the Atlantic Ocean was observed on 68% of the days; transport from Europe on 13%; low transport and local influences on 7%; and transport from the Mediterranean region on 3% of the days. The mean O₃ concentrations were 45 and 55 μg m⁻³ in Pamplona and Alsasua, respectively, which were above the values reported for the main Spanish cities. The mean NO and NO₂ levels were very similar in both sites (12 and 26 μg m⁻³, respectively). Mean SO₂ levels were 8 μg m⁻³ in Pamplona and 5 μg m⁻³ in Alsasua. Hourly levels of PM₁₀, NO and NO₂ showed similar variations with the typically two coincident maximums during traffic rush hours demonstrating a major anthropogenic origin of PM₁₀, in spite of the sporadic dust outbreaks.     

电力跨区域调配隐含的污染转移效应

为研究中国30个省/自治区/直辖市之间电力区域调配的污染物转移效应,构建了电力传输的污染转移模型,并以SO_2和NO_x为例对2006、2015年数据进行测算。结果表明,2015年电力行业SO_2、NO_x排放强度分别由2006年的4.03、2.18 g/(kW·h)下降到0.69、0.77 g/(kW·h)。2015年,16个电力净输入区通过电力跨区域传输的SO_2、NO_x转移量分别为47.8×10~4、53.0×10~4t,占这些地区电力行业SO_2、NO_x排放量的24.1%、24.2%;14个电力净输出区通过电力跨区域传输的SO_2、NO_x转移量分别为-54.6×10~4、-52.1×10~4t,占这些地区电力行业SO_2、NO_x排放量的26.5%、22.8%。研究结果对于分析区域物质流动所隐含的污染流动,全面认识区域污染物排放格局,制定合理的区域污染减排目标具有一定借鉴意义。     

Influence of Meteorological Parameters on Particulates and Atmospheric Pollutants at Taichung Harbor Sampling Site

Atmospheric aerosol particles and metallic concentrations, ionic species were monitored at the Experimental harbor of Taichung sampling site in this study. This work attempted to characterize metallic elements and ionic species associated with meteorological conditions variation on atmospheric particulate matter in TSP, PM_2.5, PM_2.5–10. The concentration distribution trend between TSP, PM_2.5, PM_2.5–10 particle concentration at the TH (Taichung harbor) sampling site were also displayed in this study. Besides, the meteorological conditions variation of metallic elements (Fe, Mg, Cr, Cu, Zn, Mn and Pb) and ions species (Cl⁻, NO₃ ⁻, SO₄ ²⁻, NH₄ ⁺, Mg²⁺, Ca²⁺ and Na⁺) concentrations attached with those particulate were also analyzed in this study. On non-parametric (Spearman) correlation analysis, the results indicated that the meteorological conditions have high correlation at largest particulate concentrations for TSP at TH sampling site in this study. In addition, the temperature and relative humidity of meteorological conditions that played a key role to affect particulate matter (PM) and have higher correlations then other meteorological conditions such as wind speed and atmospheric pressure. The parameter temperature and relative humidity also have high correlations with atmospheric pollutants compared with those of the other meteorological variables (wind speed, atmospheric pressure and prevalent wind direction). In addition, relative statistical equations between pollutants and meteorological variables were also characterized in this study.     

Ambient air quality of Lucknow City (India) during use of fireworks on Diwali Festival

The present study deals with the effect of fireworks on ambient air quality during Diwali Festival in Lucknow City. In this study, PM₁₀, SO₂, NO _x and 10 trace metals associated with PM₁₀ were estimated at four representative locations, during day and night times for Pre Diwali (day before Diwali) and Diwali day. On Diwali day 24 h average concentration of PM₁₀, SO₂, and NO _x was found to be 753.3, 139.1, and 107.3 μg m⁻³, respectively, and these concentrations were found to be higher at 2.49 and 5.67 times for PM₁₀, 1.95 and 6.59 times for SO₂ and 1.79 and 2.69 for NO _x , when compared with the respective concentration of Pre Diwali and normal day, respectively. On Diwali day, 24 h values for PM₁₀, SO₂, and NO _x were found to be higher than prescribed limit of National Ambient Air Quality Standard (NAAQS), and exceptionally high (7.53 times) for PM₁₀. On Diwali night (12 h) mean level of PM₁₀, SO₂ and NO _x was 1,206.2, 205.4 and 149.0 μg m⁻³, respectively, which was 4.02, 2.82 and 2.27 times higher than their respective daytime concentrations and showed strong correlations (p < 0.01) with each other. The 24 h mean concentration of metals associated with PM₁₀ was found to be in the order of Ca (3,169.44) > Fe (747.23) > Zn (542.62) > Cu (454.03), > Pb (307.54) > Mn (83.90) > Co (78.69) > Cr (42.10) > Ni (41.47) > Cd (34.69) in ng m⁻³ and all these values were found to be higher than the Pre Diwali (except Fe) and normal day. The metal concentrations on Diwali day were found to be significantly different than normal day (except Fe & Cu). The concentrations of Co, Ni, Cr and Cd on Diwali night were found to be significantly higher than daytime concentrations for Pre Diwali (control). The inter correlation of metals between Ca with Pb, Zn with Ni and Cr, Cu with Co, Co with Mn, Ni with Cd, Mn with Cd, Ni with Cd and Cr, and Cr with Cd showed significant relation either at p < 0.05 or P < 0.01 levels, which indicated that their sources were the same. The metals Cu, Co, Ni, Cr and Cd showed significant (p < 0.01) association with PM₁₀. These results indicate that fireworks during Diwali festival affected the ambient air quality adversely due to emission and accumulation of PM₁₀, SO₂, NO _x and trace metals. ITRC Communication Number 2538     

Extreme Nitrogen Oxide and Ozone Concentrations in Athens Atmosphere in Relation to Meteorological Conditions

In the present study, we investigate the variation of NO _x (NO + NO₂) and O₃ concentrations and the relation between the extreme events (episodes) of NO _x and O₃ concentrations and the relevant meteorological conditions in the urban atmosphere of the Athens basin. Hourly data of NO, NO₂ and O₃ concentrations from 10 representative monitoring sites located in the Athens basin were used, covering the 10-year time period from 1994 to 2003. The results of our analysis show that the concentrations of air pollutants differ significantly from one monitoring site to another, due to the location and proximity of each station to the emission sources. For each site, there are also significant differences in NO _x and O₃ concentrations from day to day, as well as from month to month and/or from season to season. The annual and seasonal variations show higher NO values in winter and lower in summer. On the contrary, NO₂ and O₃ values are higher in summer (photochemical production of O₃) and lower in winter. These differences are attributed, to a large extent, to the prevailing synoptic and meteorological conditions, the most important between them being the wind direction and speed as well as the atmospheric pressure. Our analysis of the identified 179 extreme NO _x air pollution events shows that most of them took place under anticyclonic conditions, associated with calm or weak winds (speed <2.5 ms⁻¹) of mostly southern to southwestern directions, as well as with low air temperatures and intense stable surface atmospheric conditions. There exists a significant decreasing tendency in NO _x air pollution episodic events over the 10-year study period, resulting in very few to none events in the period from 2000 to 2003. As far as it concerns the extreme O₃ concentrations, 34 air pollution events were identified, occurring under high air temperatures, variable weak winds and intense solar irradiation. The trends of O₃ concentrations are stronger in suburban sites than in urban ones.     

湿法脱硫烟气中多形态颗粒物的测量方法及组分特征

为全面测量固定源湿法脱硫烟气中多形态颗粒物的排放浓度及其离子组成特征,提出了一种基于一级冷凝、二级过滤和一级冲击吸收的多形态烟气颗粒物的同步测量方法,外场实测了3种湿法脱硫和除尘工艺的排放水平。现场测试表明：简易湿法除尘脱硫（NaOH法）一体化装置烟气中可过滤颗粒物（FPM）浓度为（36±11）mg/m³,可逃逸颗粒物（EPM）浓度为（33±7）mg/m³;氧化镁法+布袋除尘工艺烟气中FPM浓度为（14±5）mg/m³,EPM浓度为（13±6）mg/m³;石灰石-石膏脱硫+电袋除尘工艺烟气中FPM浓度低,小于3 mg/m³,EPM浓度为（6±1）mg/m³;烟气中EPM是传统滤膜法检测FPM浓度的0.7~5.7倍,EPM的主要存在形态为冷凝液中的可溶解颗粒物（DPM）,颗粒物的组分与脱硫方法密切相关,各形态颗粒物的主要组分是SO₄^2-、SO₃^2-、NO₃^-、NO₂^-、NH₄⁺、Cl^-、Na⁺、Mg²⁺和Ca²⁺等离子。     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Atmospheric concentrations of nitric acid, sulfur dioxide, particulate nitrate and particulate sulfate, and estimation of their dry deposition on the urban- and mountain-facing sides of Mt. Gokurakuji, Western Japan

Atmospheric concentrations of nitric acid (HNO₃), sulfur dioxide (SO₂), particulate nitrate and particulate sulfate on the urban- and mountain-facing sides of Mt. Gokurakuji were measured from November 2002 to October 2003, in order to evaluate the effects of anthropogenic activity on air quality and dry deposited nitrate and sulfate on the surfaces of pine foliage. The results showed that HNO₃, SO₂ and concentrations were significantly higher (P < 0.05) on the urban-facing side (1.54, 2.48 and 0.65 μg m⁻³, respectively) than the mountain-facing side (0.67, 1.19 and 0.37 μg m⁻³, respectively), while concentrations did not differ significantly between the two sides (urban-facing: 2.80 μg m⁻³; mountain−facing: 2.05 μg m⁻³). Indirect estimates of dry deposition rates of nitrate and sulfate to the surfaces of pine foliage based on the measured concentrations approximately agreed with the measured values determined by the foliar rinsing technique in a previous study. It was found that HNO₃ was the major source (approximately 80%) of dry deposited nitrate on pine foliage, while the contribution from was about equal to that from SO₂. In conclusion, HNO₃ and SO₂ appear to be dominant species reflecting higher dry deposition rates of nitrate and sulfate on the urban-facing side compared to the mountain-facing side of Mt. Gokurakuji.     

Emissions of SO2, NO x and particulates from a pipe manufacturing plant and prediction of impact on air quality

Integrated pipe manufacturing industry is operation intensive and has significant air pollution potential especially when it is equipped with a captive power production facility. Emissions of SO₂, NO _x , and particulate matter (PM) were estimated from the stationary sources in a state-of-the-art pipe manufacturing plant in India. Major air polluting units like blast furnace, ductile iron spun pipe facility, and captive power production facility were selected for stack gas monitoring. Subsequently, ambient air quality modeling was undertaken to predict ground-level concentrations of the selected air pollutants using Industrial Source Complex (ISC 3) model. Emissions of SO₂, NO _x , and particulate matter from the stationary sources in selected facilities ranged from 0.02 to 16.5, 0.03 to 93.3, and 0.09 to 48.3 kg h^???1, respectively. Concentration of SO₂ and NO _x in stack gas of 1,180-kVA (1 KW = 1.25 kVA) diesel generator exceeded the upper safe limits prescribed by the State Pollution Control Board, while concentrations of the same from all other units were within the prescribed limits. Particulate emission was highest from the barrel grinding operation, where grinding of the manufactured pipes is undertaken for giving the final shape. Particulate emission was also high from dedusting operation where coal dust is handled. Air quality modeling indicated that maximum possible ground-level concentration of PM, SO₂, and NO _x were to the tune of 13, 3, and 18 μg/m³, respectively, which are within the prescribed limits for ambient air given by the Central Pollution Control Board.     

Study of metals concentration levels in Patella piperata throughout the Canary Islands, Spain

In order to assess the extent of metal contamination at rocky shores of the Canarian Archipelago, metal concentrations have been measured in Patella piperata (Gould, 1846), using the standard atomic absorption spectrophotometer technique. Ranges of elements concentrations measured (in μg g⁻¹) found in the biota were: Cd (0.36 ± 0.26 μg g⁻¹ dry wt.), Cu (2.05 ± 0.91 dry wt.), Pb (1.57 ± 1.14 μg g⁻¹dry wt.) and Zn (10.37 ± 4.60 μg g⁻¹ dry wt.). Variation in metal concentrations in Patella, was tested by using non-parametric statistical methods. Cd content had a maximum in the Archipelago Chinijo, northward of Lanzarote Island. The metal concentrations recorded at the clean stations may be considered carefully if they are used like background levels.     

Characteristic Study of Dry Deposition, Concentration, Compositions for Particulates Mass and Ionic Species During Summer and Autumn Season at a Traffic Sampling Site

Aerosol samples for dry deposition and total suspend particulates (TSP) were collected from August to November of 2003 in central Taiwan. Ion chromatography was used to analyze the related water-soluble ionic species (Cl⁻, NO₃ ⁻, SO₄ ²⁻, Na⁺, NH₄ ⁺, K⁺, Mg²⁺ and Ca²⁺). The results obtained in this study indicated that the ambient air particulate mass concentrations in the daytime period (averaged 975.4 μg m⁻³) were higher than the nighttime period (averaged 542.1 μg m⁻³). And the daytime dry deposition fluxes (averaged 58.12 μg m⁻² sec⁻¹) were about 2.2 times as that of nighttime dry deposition fluxes (averaged 26.54 μg m⁻² sec⁻¹) of the downward dry deposition. The average values downward and upward of dry deposition fluxes for the weekend period were almost higher than the weekday period for either daytime or nighttime period. Furthermore, the average daytime dry deposition fluxes (averaged 26.37 μg m⁻² sec⁻¹) were also about 2.3 times as that of nighttime dry deposition fluxes (averaged 11.52 μg m⁻² sec⁻¹). Moreover, the results also indicate that SO₄ ²⁻ and Ca²⁺ have higher average composition for total suspended particulates in the daytime period while Ca²⁺, SO₄ ²⁻, and Na⁺ have the higher average composition for total suspends particulates in the nighttime period.     

Distribution of PM2.5 and PM10-2.5 in PM10 Fraction in Ambient Air Due to Vehicular Pollution in Kolkata Megacity

This research paper aims at establishing baseline PM₁₀ and PM_2.5 concentration levels, which could be effectively used to develop and upgrade the standards in air pollution in developing countries. The relative contribution of fine fractions (PM_2.5) and coarser fractions (PM_10-2.5) to PM₁₀ fractions were investigates in a megacity which is overcrowded and congested due to lack of road network and deteriorated air quality because of vehicular pollution. The present study was carried out during the winter of 2002. The average 24h PM₁₀ concentration was 304 μg/m³, which is 3 times more than the Indian National Ambient Air Quality Standards (NAAQS) and higher PM₁₀ concentration was due to fine fraction (PM_2.5) released by vehicular exhaust. The 24h average PM_2.5 concentration was found 179 μg/m³, which is exceeded USEPA and EU standards of 65 and 50 μg/m³ respectively for the winter. India does not have any PM_2.5 standards. The 24 h average PM_10-2.5 concentrations were found 126 μg/m³. The PM_2.5 constituted more than 59% of PM₁₀ and whereas PM₁₀-PM_2.5 fractions constituted 41% of PM₁₀. The correlation between PM₁₀ and PM_2.5 was found higher as PM_2.5 comprised major proportion of PM₁₀ fractions contributed by vehicular emissions.     

Inter-Laboratory Comparison of No2 and SO2 Generated by Dynamic Dilution System Under Laboratory Conditions: A Technical Discussion

A workshop on analytical quality control (AQC) of ambient air quality measurement methods for nitrogen dioxide (NO₂) and sulphur dioxide (SO₂) was conducted by Central Pollution Control Board (CPCB) for officials involved in National Ambient Air Quality Monitoring (NAAQM) in India. Concentrations of NO₂ and SO₂ were generated by dynamic dilution system under laboratory conditions at low and high levels and measured using static dilution system and wet chemical methods laid down by CPCB under section 16(2)(h) of the air act 1981. CPCB provided the measured values as reference values for comparing the means obtained by the officials participated from thirteen organizations. A tolerance limit of ±15% of the reference values was specified to accept the results. Generated concentrations, which were unknown to the participants, were measured using gaseous sampling assembly (Envirotech APM 411, New Delhi, India), and wet chemical methods laid down by CPCB i.e. the same methodology which is used by the organizations to generate the data of NO₂ and SO₂ in ambient air. Simultaneously, concentrations were checked by CPCB using automatic analyzers as a check on reference concentration. It is observed that results of automatic analyzers for NO₂ and SO₂ were within a tolerance of ±5% with %RSD below 3. On the other hand, results of most of the participants showed variability in the measurements with %RSD ranging between ±0.8 and ±88.6 and exceedences of means from the tolerance limit with bias ranging between 1.4 and −59%. To check the cause of high variability in the measurements obtained under identical conditions, duplicate sampling was performed by one of the participants for SO₂ at low concentration level. In this study, results of wet chemical methods, automatic analyzers and results of duplicate sampling are analysed statistically to assess the cause of high variability in the measurements. Analysis of t-test and analysis of variance (ANOVA) showed highly significant results for NO₂ and SO₂ at high concentration levels (α 0.05) and for SO₂ at both the levels (α 0.01) respectively indicating some bias is existing either in the sampling or in analytical technique. Duplicate sampling performed to check precision in parallel measurements showed high %RSD indicating the presence of systematic error in sampling technique as the same calibration factor (CF) was used to measure the concentration of duplicate samples. Statistical analysis of flow rates of duplicate sampling showed that the sampling assembly could not maintain the constant flow rate within the ±10% with that measured at the start of the sampling. This resulted in high %RSD and deviation from the reference values for the results of most of the participants, even after accepting ±15% tolerance limit. There is a need to improve and evaluate this gaseous sample collection device under laboratory conditions to generate reliable database of NO₂ and SO₂ in ambient air.     

Development of baseline (air quality) data in Pakistan

During 2003–2004, SUPARCO, the Pakistan Space and Upper Atmosphere Research Commission has conducted a year long baseline air quality study in country’s major urban areas (Karachi, Lahore, Quetta, Rawalpindi, Islamabad and Peshawar). The objective of this study was to establish baseline levels and behavior of airborne pollutants in urban centers with temporal and spatial parameters. This study reveals that the highest concentrations of CO were observed at Quetta (14 ppm) while other pollutants like SO₂ (52.5 ppb), NO _x (60.75 ppb) and O₃ (50 ppb) were higher at Lahore compared to other urban centers like Karachi, Peshawar etc. The maximum particulate (TSP) and PM10 levels were observed at Lahore (996 ug/m³ and 368 ug/m³ respectively), Quetta (778 ug/m³, 298 ug/m³) and in Karachi (410 ug/m³, 302 ug/m³). In all major cities the highest levels were recorded at major intersections and variations were directly correlated with traffic density. These pollutants showed highest levels in summer and spring while lowest were observed in winter and monsoon. A data bank has been generated for future planning and air pollution impact studies.     

Monitoring of Fogwater Chemistry in the Gulf Coast Urban Industrial Corridor: Baton Rouge (Louisiana)

Seventeen fog events were sampled in Baton Rouge, Louisiana during 2002–2004 as part of characterizing wet deposition by fogwater in the heavily industrialized corridor along the Louisiana Gulf Coast in the United States. These samples were analyzed for chemical characteristics such as pH, conductivity, total organic and inorganic carbon, total metals and the principal ion concentrations. The dominant ionic species in all samples were NH₄⁺, NO₃⁻, Cl⁻ and SO₄²⁻. The pH of the fogwater sampled had a mean value of 6.7 with two cases of acidic pH of 4.7. Rainwater and fogwater pH were similar in this region. The acidity of fogwater was a result of NO₃⁻ but partly offset by high NH₄⁺. The measured gaseous SO₂ accounted for a small percentage of the observed sulfate concentration, indicating additional gas-to-particle conversion of SO₂ to sulfate in fogwater. The gaseous NO_x accounted for most of the dissolved nitrate and nitrite concentration in fogwater. The high chloride concentration was attributable to the degradation of chlorinated organics in the atmosphere. The metal composition was traced directly to soil-derived aerosol precursors in the air. The major metals observed in fogwater were Na, K, Ca, Fe, Al, Mg and Zn. Of these Na, K, Ca and Mg were predominant with mean concentrations > 100 μM. Al, Fe and Zn were present in the samples, at mean concentrations < 100 μM. Small concentrations of Mn (7.8 μM), Cu (2 μM), Pb (0.07 μM) and As (0.32 μM) were also observed in the fogwaters, and these were shown to result from particulates (PM_2.5) in the atmosphere. The contribution to both ions and metals from the marine sources in the Louisiana Gulf Coast was minimal. The concentrations of all principal ionic species and metals in fogwater were 1–2 orders of magnitude larger than in rainwater. Several linear alkane organic compounds were observed in the fogwater, representing the contributions from petroleum products at concentrations far exceeding their aqueous solubility. A pesticide (atrazine) was also observed in fogwater, representing the contribution from the agricultural activities nearby.     

Ambient Air Quality Status in Raniganj-Asansol Area, India

This investigation presents the assessment of ambient air quality with respect to suspended particulate matter (SPM), sulphur dioxide (SO₂) and oxides of nitrogen (NO_X) at four sites (RGC, SRS, BBC and BCC) in the Raniganj-Asansol area in West Bengal, India. Ambient air was monitored with a sampling frequency of twenty four hours (3 × 8 hours) at each site on every alternate day (3 days a week) covering a period of one year. A total of 429 samples were collected from RGC, 429 from SRS and 435 each from the BBC and BCC sites. Meteorological parameters such as temperature, relative humidity, wind-speed and wind-direction were also recorded simultaneously during the sampling period. Monthly and seasonal variation of these pollutants have been observed and recorded. The annual average and range values have also been calculated. Results of the investigation indicates that the 95th percentile values of SPM levels exceed the limits (200 g m^-3) at RGC, SRS and BBC sites and is within the limit of 500 g m^-3 at the BCC sites. The 95th percentile values of SO₂ levels did not exceed the reference level at any of the monitoring stations. The 95th percentile values of NO_X are found to be exceeding the limit (80 g m^-3) at RGC, SRS and BBC sites but is within the prescribed limit of 120 g m^-3 at the BCC site. Further, it has been observed that the concentrations of the pollutants are high in winter in comparison to the summer or the monsoon seasons. Results of the investigation indicates that industrial activities, indiscriminate open air burning of coal by the local inhabitants for cooking as well as coking purposes, vehicular traffic, etc. are responsible for the high concentration of pollutants in this area.     

Assessment of environmental impact on air quality by cement industry and mitigating measures: a case study

In this study, environmental impact on air quality was evaluated for a typical Cement Industry in Nigeria. The air pollutants in the atmosphere around the cement plant and neighbouring settlements were determined using appropriate sampling techniques. Atmospheric dust and CO₂ were prevalent pollutants during the sampling period; their concentrations were recorded to be in the range of 249–3,745 mg/m³ and 2,440–2,600 mg/m³, respectively. Besides atmospheric dust and CO₂, the air pollutants such as NO _x , SO _x and CO were in trace concentrations, below the safe limits approved by FEPA that are 0.0062–0.093 mg/m³ NO _x , 0.026 mg/m³ SO _x and 114.3 mg/m³ CO, respectively. Some cost-effective mitigating measures were recommended that include the utilisation of readily available and low-cost pozzolans material to produce blended cement, not only could energy efficiency be improved, but carbon dioxide emission could also be minimised during clinker production; and the installation of an advance high-pressure grinding rolls (clinker–roller-press process) to maximise energy efficiency to above what is obtainable from the traditional ball mills and to minimise CO₂ emission from the power plant.     

北京市典型重污染过程中PM2.5载带水溶性无机离子污染特征分析

为研究北京地区冬季PM_(2.5)载带的水溶性无机离子组分污染特征,2013年1月在中国环境科学研究院内采用在线离子色谱(URG-9000B,AIM-IC)对PM_(2.5)中水溶性无机离子(SO_4~(2-)、NO_3~-、Cl~-、NH_4~+、Na~+、K~+、Mg~(2+)、Ca~(2+))进行监测与分析。结果表明,采样期间总水溶性无机离子(TWSI)浓度为61.0μg/m~3,其中二次无机离子SO_4~(2-)、NO_3~-、NH_4~+(SNA)占比达72.3%,在PM_(2.5)中占比为40.29%,表明北京市PM_(2.5)二次污染严重。重污染天[NO_3~-]/[SO_4~(2-)]表明,固定源污染较移动源更为显著。三元相图表明,在空气质量为优的情况下,NH_4~+(在SNA中占比为30.3%~65.5%,下同)主要以NH_4NO_3的形式存在,较少比例以(NH_4)_2SO_4存在;严重污染时,NH_4~+(47.3%~77.9%)主要以(NH_4)_2SO_4形式存在,其次以NH_4NO_3的形式存在,其余的NH_4~+以NH_4Cl的形式存在。[NO_3~-]/[SO_4~(2-)]日变化表明,早、晚机动车高峰影响北京重污染发生。     

灰霾期间武汉城市区域大气污染物的理化特征

利用湖北省大气复合污染自动监测站2013年的全年监测数据,分析了灰霾期间武汉城市区域大气污染物的理化特征。霾日主要出现在春季、秋季和冬季。霾日与非霾日大气污染物质量浓度和气象参数的对比分析结果显示:高湿度、静风是武汉城市区域霾日的重要气象特征;PM1、PM_(2.5)、PM_(10)、NO_2、CO、NH3的质量浓度,SOR、NOR值以及PM_(2.5)中的二次无机离子(SO2-4、NO-3、NH+4)和部分元素(Pb、Se、Cd、Zn、K)的质量浓度均在霾日明显高于非霾日,而霾日SO2质量浓度仅在冬季略高于非霾日。选取2013年1月的连续灰霾日进行相关性分析,结果表明:污染组分主要来自当地排放(包括直接排放和二次形成),并受当地气象条件影响。此次灰霾过程中PM_(2.5)中的硫酸盐和硝酸盐主要来自气相反应,气态NO_2主要生成了气态HNO_3,而不是HNO_2。     

Suspended Particulate Matter Distribution in Rural-Industrial Satna and in Urban-Industrial South Delhi

An air quality sampling program was designed and implemented to collect the baseline concentrations of respirable suspended particulates (RSP = PM₁₀), non-respirable suspended particulates (NRSP) and fine suspended particulates (FSP = PM_2.5). Over a three-week period, a 24-h average concentrations were calculated from the samples collected at an industrial site in Southern Delhi and compared to datasets collected in Satna by Envirotech Limited, Okhla, Delhi in order to establish the characteristic difference in emission patterns. PM_2.5, PM₁₀, and total suspended particulates (TSP) concentrations at Satna were 20.5 ± 6.0, 102.1 ± 41.1, and 387.6 ± 222.4 μg m⁻³ and at Delhi were 126.7 ± 28.6, 268.6 ± 39.1, and 687.7 ± 117.4 μg m⁻³. Values at Delhi were well above the standard limit for 24-h PM_2.5 United States National Ambient Air Quality Standards (USNAAQS; 65 μg m⁻³), while values at Satna were under the standard limit. Results were compared with various worldwide studies. These comparisons suggest an immediate need for the promulgation of new PM_2.5 standards. The position of PM₁₀ in Delhi is drastic and needs an immediate attention. PM₁₀ levels at Delhi were also well above the standard limit for 24-h PM₁₀ National Ambient Air Quality Standards (NAAQS; 150 μg m⁻³), while levels at Satna remained under the standard limit. PM_2.5/PM₁₀ values were also calculated to determine PM_2.5 contribution. At Satna, PM_2.5 contribution to PM₁₀ was only 20% compared to 47% in Delhi. TSP values at Delhi were well above, while TSP values at Satna were under, the standard limit for 24-h TSP NAAQS (500 μg m⁻³). At Satna, the PM₁₀ contribution to TSP was only 26% compared to 39% in Delhi. The correlation between PM₁₀, PM_2.5, and TSP were also calculated in order to gain an insight to their sources. Both in Satna and in Delhi, none of the sources was dominant a varied pattern of emissions was obtained, showing the presence of heterogeneous emission density and that nonrespirable suspended particulate (NRSP) formed the greatest part of the particulate load.