用活性填料催化氧化-硝酸吸收法脱除氮氧化物的研究

为了提高硝酸吸收氮氧化物的效率，对活性填料催化氧化-硝酸吸收NOx进行了研究。结果表明：活性填料能明显提高NOx的吸收效率；当NOx中NO2体积百分含量增加，其吸收效率增加；随进气浓度和液气比的增大，NOx吸收效率增加；随NO2浓度的增加，NO的吸收效率先增加后减少，在NO／NO2为3时，NO吸收效率最高；随NO的增加NO2的吸收效率先增加后减少，在NO／NO2为0．6～1之间，NO2的吸收效果较好。     

填料塔中的DBU溶液吸收CO_2

在自制的1,8-二氮杂双环[5,4,0]十一碳-7-烯(DBU)吸收CO2的填料塔中,研究DBU溶液浓度、入口CO2浓度、DBU溶液流量、气体流量、气体温度以及填料层高度对CO2吸收的影响。结果表明,DBU溶液浓度从1.5%增加到25%,CO2吸收容量和吸收效率均逐步减小;入口CO2浓度从4.5%增加到15%,CO2吸收容量和吸收效率均逐渐增大;DBU溶液流量从20 m L/min增加到120 m L/min,CO2吸收容量和吸收效率略有增加;气体流量从0.7 L/min增加到3.3 L/min,填料层高度从5 cm增加到45 cm,CO2吸收容量和吸收效率均呈先增后减趋势;气体温度从25℃增加到60℃,CO2吸收容量和吸收效率略有下降。DBU溶液在填料塔内能够高效吸收气体中的CO2。     

尿素/三乙醇胺吸收烟气NO_x的实验研究

以尿素作为吸收液,与NOx反应生成N2和CO2,脱除烟气中的氮氧化物。以一套双级串连的填料塔为主体反应器,分别对气速、液气比、反应物浓度、添加剂浓度和反应温度等参数对尿素溶液吸收NOx反应的影响进行了实验研究,获得了优化实验工况,研究结果显示,在气速为0.1 m/s、液气比为16 L/m3、三乙醇胺为0.01%（质量比）、尿素浓度为13%（质量比）工况下,反应温度为30~70℃,脱硝总效率可达50%以上,且随着NOx体积分数增加而提高。     

电弧放电产生NOx及其对亚硫酸铵的氧化

将脱硫塔产生的高浓度亚硫酸铵氧化为硫酸铵是氨法脱硫研究的一个难点.利用二氧化氮(NO2)的氧化性,可以有效氧化高浓度的亚硫酸铵.空气中电弧放电可以产生氮氧化物(NOx),本研究采用高频交流电源,不锈钢针-针电极,研究了放电间距、气体流量、湿度和O2含量等参数对产物NOx的浓度和NO2/NOx比值的影响,并对产物气体做了红外分析和光谱分析.实验结果表明,放电间距增大有利于NOx浓度和NO2/NOx的提高,气体流量和湿度的增大使NOx浓度和NO2/NOx降低,O2含量为50％和60％时NO2浓度和NO2/NOx分别达到最大值.产物NOx对亚硫酸铵的氧化速率最高可达0.0264 mol/(L·min).     

氨-Fe(Ⅱ)EDTA法同步脱硫脱硝中试研究

在中试吸收塔反应器中,以氨基湿法烟气脱硫为基础,结合Fe(Ⅱ)EDTA络合吸收NO技术,实现同步脱硫脱硝;采用单一变量法研究了塔型、填料几何特性、填料层高度、液气比和Fe(Ⅱ)EDTA浓度等因素对同步脱硫脱硝的影响。结果表明,在相同的条件下,填料塔比空喷塔和鼓泡塔有利于同步脱硫脱硝;空隙率高、填料因子小的填料能明显提高脱硫脱硝效率,填料层高度从0 mm增加到900 mm,脱硫脱硝效率分别增大了4.49%和19.55%;液气比和Fe(Ⅱ)EDTA浓度越大,脱硝效率越高,但对SO_2的吸收没有影响。最佳工艺条件为:ф25 mm鲍尔环作填料且填料层高度为900 mm的填料塔、液气比为12 L/m~3、Fe(Ⅱ)EDTA浓度为0.05 mol/L,在此条件下,脱硫脱硝效率分别达到100%和51.55%。     

DOC系统催化性能的仿真和分析

以Langmuire Hinshelwood机理为理论依据,基于MATLAB/Simulink建立DOC系统的数值计算模型,研究不同参数(如空速、氧气浓度、NO2/NOx比例)对氮氧化物(NOx)、一氧化碳(CO)、碳氢化合物(HC)转化效率的影响,并对部分工况进行了实验研究,从而验证数值模型的准确性。结果表明,空速的降低可以增大DOC对CO、HC、NO的氧化性能,这是由于排气在催化器内的反应时间增长。当排气温度为225~300℃时,减小空速对增大HC的氧化效率效果明显,当排气温度在175~450℃范围内,减小空速对增大NO的氧化效率影响明显;当O2浓度低于1%,排气温度在175~250℃时,CO转化效率增大,在250℃之后均接近100%。当O2浓度为10%时,温度的变化对CO的转化效率影响很小。当O2浓度大于1%时,温度的变化对NO的氧化效率影响较大;当排气温度在300~550℃时,NO2/NOx比例的变化对NO的转化效率影响较大。降低排气中NO2/NOx比例,能够在排气温度高于300℃时,明显提高NO的转化效率。     

Cd、Pb复合污染下柠檬酸对龙葵修复效率及抗氧化酶的影响

植物修复土壤重金属被普遍认为是清洁、经济的生物修复方法。为了提高生物修复土壤重金属污染的效率,在室内盆栽实验中添加柠檬酸作为螯合剂促进龙葵对重金属的吸收,并研究其生理活性的变化。结果表明:当添加柠檬酸浓度为10 nmol/kg时,龙葵生物量显著提高(P<0.05),各部分生物量表现为:茎>叶>根;随着柠檬酸浓度的增加,龙葵对重金属Cd的吸收量显著(P<0.05)增加,在10 nmol时总吸收量最大,为229.85μg/g DW;龙葵对Cd、Pb的富集系数均在柠檬酸浓度为5 nmol/kg时达到最大;Pb吸收量随柠檬酸浓度增加表现出先增大后减小的趋势;添加柠檬酸促进了龙葵对Cd的吸收,增强了抗氧化酶活性,而对Pb的吸收效果不明显。     

ClO_2气相氧化联合CaCO_3浆液吸收同时脱硫脱硝试验研究

采用ClO_2气相氧化联合CaCO_3浆液吸收工艺对模拟烟气进行同时脱硫脱硝,研究了ClO_2/NO摩尔比、SO_2初始浓度对气相氧化段NO氧化率的影响及液相吸收段中CaCO_3浆液pH、温度和液气比对同时脱硫脱硝效果的影响。结果表明,在气相氧化段,NO的氧化率随着ClO_2/NO摩尔比的增加呈先快速增加后逐渐平稳的变化趋势;在给定的ClO_2/NO摩尔比(0.8)下,随着SO_2初始浓度的增加,NO氧化率稍有下降,高浓度SO2的存在对ClO_2氧化NO的抑制作用有限,说明ClO_2对NO的氧化反应具有良好的选择性。ClO_2气相氧化联合CaCO_3浆液吸收工艺最优反应条件:ClO_2/NO摩尔比为0.8,CaCO_3浆液初始pH为7.0、温度为55℃,液气比为18L/m3。当SO2初始质量浓度为1 000 mg/m~3、NO_x初始质量浓度为509 mg/m3时,最佳反应条件下SO_2去除率达100.00%,NO_x去除率达81%左右。     

催化氧化还原吸收法脱除工业含湿废气中NOx

基于精细化工、制药行业排出 NOx 废气氧化度低、氧气含量高的特点,提出以改性活性炭(MAC)为催化剂的催化氧化-还原吸收脱除 NOx 的方法.考察了相对湿度、氧化温度、氧化时间对 NO 催化氧化以及还原液种类对 NOx 吸收的影响.结果表明,随着相对湿度的增加 NO 转化率急剧下降,但随着氧化时间的延长有所提高;干气条件下,随着温度升高,NO 转化率下降;湿气条件下,NO 氧化反应最佳反应温度范围为 50～70℃,实验条件下的 NO 最高转化率可达 51%;还原液种类中以尿素-碱液对 NOx 和 NO 的吸收效果最好,亚硫酸铵-碱液对 NOx 的吸收效果最好.通过催化氧化-还原吸收的多级组合可实现 NOx 的有效脱除与达标排放.     

Fe~Ⅱ（EDTA）协同生物转鼓过滤器去除NO的实验研究

采用自行研制的生物转鼓反应器（RDB）处理难溶于水的NO废气,为提高NO的传质系数和去除效率,实验考察了营养液中添加FeⅡ（EDTA）络合剂协同RDB以提高NO去除效率的过程。结果表明,当空床停留时间（EBRT）为0.96 min时,在营养液中添加FeⅡ（EDTA）至100 mg/L后,NO的去除效率从70.78%升至79.26%。未添加FeⅡ（EDTA）时NO去除率随营养液的增加下降,添加FeⅡ（EDTA）至100 mg/L后,去除率随营养液量的增加先上升后下降,且下降速率比上升速率大。随着营养液中FeⅡ（EDTA）浓度从0增加至500 mg/L,实验最佳温度从32.5℃升至47.5℃,但添加FeⅡ（ED-TA）至100 mg/L对实验的最适pH值没有太大影响。     

水吸收法处理低浓度氮氧化物废气的中试研究

对水在中试规模下吸收低浓度的氮氧化物废气进行了研究。分别研究了喷淋密度、温度、压力、气速以及氮氧化物浓度对吸收效果的影响,结果表明,综合考虑各种因素,喷淋密度在20 m3/（m2·h）,水温在15℃以下,气速小于0.28 m/s,废气浓度在400 mg/m3左右时,氮氧化物的平均脱除率可以达到50%左右;同时,随着压力的增大,吸收效率也增加。     

工业废气中氮氧化物的治理研究

对碱液吸收和活性炭吸附两级联合治理氮氧化物废气进行了实验研究,结果表明:对于氮氧化物进口浓度为7000～10 000 mg/m3的氮氧化物废气,氮氧化物的平均脱除率可以达到99%,出口浓度低于99 mg/m3;还进行了以硝酸溶液、双氧水溶液和高锰酸钾溶液为氧化剂湿法氧化碱吸收的实验研究,结果显示3种氧化剂都能显著提高氮氧化物的脱除率,其中以高锰酸钾溶液作氧化剂的脱除效果最好,其次是双氧水溶液.     

Photocatalytic oxidation of NOx using composite sheets containing TiO2 and a metal compound

The photocatalytic oxidation of nitrogen oxides (NO(x)) over titanium dioxide (TiO(2)) sheets containing metal compounds (MCs) had been studied. Calcium oxide (CaO), magnesium oxide (MgO), calcium carbonate (CaCO(3)), aluminium oxide (Al(2)O(3)) and ferric oxide (Fe(2)O(3)) were used as MCs. Al(2)O(3) and Fe(2)O(3) added to the TiO(2) sheet did not affect the photooxidation of nitrogen oxides (NO(x)). The CaO sheet treated with TiO(2) sol had the greatest efficiency as a NO(x) remover under UV irradiation. It is believed that CaO has a high adsorptivity for nitrogen dioxide (NO(2)) and nitric acid (HNO(3)). The amount of NO(x) removed by a TiO(2) sheet including MC showed a tendency to increase with increasing pH of the MC suspension, i.e. there is a good correlation between the alkalinity of the MC and the retention of NO(2) and HNO(3).     

Cleaning of Stack Gases Containing High Concentrations of Nitrogen Oxides

Multistage gas absorption of 1–50% nitric oxide, nitrogen dioxide, and nitrogen tetraoxide from air with water or caustic solutions can produce colorless stack discharges. The rate at which NO is oxidized to No₂ in the gas phase and the solubility rate of No₂ in water or solution are highly concentration dependent so that reductions of stack gas concentrations of nitrogen oxides below approximately 200 ppm appear to be impractical. High efficiency absorption combined with elevated discharge of the cleaned, colorless gases is an acceptable method of air pollution control for many troublesome operations. Experiences in the fields of rocketry and nuclear energy are cited. Engineering modifications of metal pickling operations have been found especially helpful in producing effective control at an acceptable cost.     

Photocatalytic oxidation of nitrogen oxides using TiO2 loading on woven glass fabric

TiO2 loading on woven glass fabric is applied to treat nitrogen oxides (NOx) by photocatalytic oxidation (PCO). In this paper, the PCO behavior of NO at high concentrations was studied by PCO of NOx at source levels (20-168 ppm). The PCO efficiency reached 27% in this experiment, while the inlet NOx concentration was 168 ppm (147 ppm NO). The dependency of the reaction rate on several key influencing factors (relative humidity, space time, inlet concentration, oxygen percentage) was also studied. The results illustrate that the resulting hydroxyl radical and active oxide play an important role in the oxidation of NOx. The reactions are limited by the thermodynamic equilibrium after ca. 15s space time. A possible explanation for the catalyst deactivation is the accumulation of nitric acid and nitrous acid on the TiO2 surface during the PCO of NOx. However, the photocatalytic activity can be recovered with a simple heat treatment. The results from the study of the effect of the inlet concentration were described with the Langmuir-Hinshelwood model.     

Comparative study on the removal efficiency of hydrogen sulfide (H2S) using three different packings

To improve the removal efficiency on hydrogen sulfide (H₂S), a biofilter was developed and was made of polyvinyl chloride (PVC) pipes. The effects of three different packings (i.e., packing A, packing B, and packing C), containing different proportions of activated carbon, sawdust, wormcast, perlite, and pig manure compost, based on different biofilter parameters on H₂S removal efficiency, were investigated. With the extension of running time, the H₂S removal rate of packing A reached up to 90.12%, that of packing B reached a peak at 92.96%, and that of packing C was highest at 87.21%. The contribution rate of each packing at the bottom of the device was significantly greater (p < 0.01) than that of other parts, and those of the top of the devices were all greater than those of the middle of the devices. The H₂S removal rate increased with greater filler layer height. The removal rate of group B increased first with humidity, and then declined, with the optimal humidity level for the removal of H₂S 50–65% in this study. With the prolongation of the run, the pH of packing A was reduced from 7.1 to 5.91, while the pH of packing B and C remained within the range of 6.53–7.10. An increase was found in the number of bacteria and fungi over time. The count of bacteria in packing B and C and following a decreasing order was bottom > middle > top, whereas that for fungi was the opposite. In conclusion, it is thought that packing B (comprising wormcast + sawdust + activated carbon) is more efficient in the removal of H₂S than the other packings and may thus be utilized in biofilters. These results hope to provide useful information for future related research on the removal efficiency of H₂S using packings.

Implications: Wormcasts use as biological filter packing to remove H₂S is limited and needs yet to be explored. A comparative study on the removal efficiency of H₂S using three packings showed the packings that included wormcast were more efficient than others, and showed the combined features of physical absorption and biological removal with long sustainability and good efficiency, although these were largely influenced by environmental factors and nutrient content for the microorganisms. In summary, wormcast could be utilized in biological filters in the future in related research beacuse of its good efficiency and low cost.     

尿素/高锰酸钾湿法烟气脱氮的试验研究

采用高锰酸钾和尿素配制成不同浓度的吸收溶液,在填有金属鲍尔环的管式吸收反应器中,对模拟烟气进行湿法烟气脱氮的研究。试验结果表明,用尿素和高锰酸钾配制成的吸收液进行湿法烟气脱氮,可以高效地脱除模拟烟气中的氮氧化物,高锰酸钾含量的增加可以显著提高脱氮效率,是决定脱氮效率高低的重要因素,在尿素和高锰酸钾含量分别为5%和0.60g/L时可以达到91.5%的平均脱氮效率;尿素含量、吸收液有效柱高和外加的SO2气体均对脱氮效率产生不同程度的影响。     

3种短链脂肪酸对活性污泥储存PHA的影响

采用经乙酸钠驯化培养具有一定聚羟基烷酸酯(PHA)储存能力的活性污泥,考察乙酸、丙酸和丁酸3种短链脂肪酸,以及乙酸、丁酸分别与丙酸按1∶1、1∶2、2∶1比例组合成的6种混合酸作为碳源时对活性污泥中PHA的储存和转化的影响。实验结果表明,在3种短链脂肪酸中,以丁酸为碳源得到活性污泥PHA储存量最高,为40.53 mg/g;在混合酸中,乙酸与丙酸按1∶2组合时,系统PHA储存量最高,为773.4 mg/g。混合酸相对于单一的脂肪酸碳源更有利于活性污泥储存PHA。在混合酸总量一定的条件下,随着丙酸比例的增加,乙酸与丙酸混合比丁酸与丙酸混合更有利于微生物的PHA储存。     

铁炭复配修复地下水中NO_3~--N的条件研究

采用了铁炭复配修复地下水中NO3--N,探讨了实验条件对修复效果的影响。结果表明,在pH值近中性条件(初始pH 6.42)下,反应时间为1 h时NO3--N修复率达到60.85%;Fe/C=1∶1时介质最佳用量分别为4~5 g;Fe/C=1/1.5时修复率为72.80%;反应速率在高振荡强度下大于低振荡强度;氧化铜的催化效果最好,可使修复率提高7.5个百分点。铁炭复配介质修复地下水中NO3--N是有效可行的,修复率随反应时间的增加而提高,在Fe/C=1∶1时修复率与介质用量呈正相关,无限减小Fe/C比并不能无限提高修复率,振荡强度对修复具有显著影响,低振荡强度下的修复过程较高强度存在滞后现象,并非所有金属氧化物催化剂对铁炭修复NO3--N均有促进作用。