Numerical study of medium to large scale BLEVE for blast wave prediction

So far, the prediction of blast wave generated from the Boiling Liquid Expanding Vapour Explosion (BLEVE) has been already broadly investigated. However, only a few validations of these blast wave prediction models have been made, and some well-established methods are available to predict BLEVE overpressure in the open space only. This paper presents numerical study on the estimation of the near-field and far-field blast waves from BLEVEs. The scale effect is taken into account by conducting two different scale BLEVE simulations. The expansion of pressurized vapour and evaporation of liquid in BLEVE are both modelled by using CFD method. Two approaches are proposed to determine the initial pressure of BLEVE source. The vapour evaporation and liquid flashing are simulated separately in these two approaches. Satisfactory agreement between the CFD simulation results and experimental data is achieved. With the validated CFD model, the results predicted by the proposed approaches can be used to predict explosion loads for better assessment of explosion effects on structures.     

A closer look at BLEVE overpressure

The overpressure produced by the boiling liquid expanding vapor explosion (BLEVE) is still not well understood. Various methods have been published on the overpressure modeling in the far field. They mostly differ by the modeling of the expansion energy, used to scale the distance to the source where the overpressure needs to be calculated. But these methods usually include a experimentally fitted reduction factor, and are mostly overestimating the overpressures. Today there is a growing interest in modeling the BLEVE overpressure in the near field, for studying the blast effect on critical infrastructure such as bridges and buildings. This requires a much better understanding of the BLEVE blast. This paper goes deeper in the understanding of the physical phenomenon leading to the BLEVE blast wave generation and propagation. First, mid-scale BLEVE experiments in addition to new experimental data for near field blast from a small scale supercritical BLEVE are analyzed. And second, an analysis method of the shocks observed in the experiments is presented based on fundamental gas dynamics, and allows the elaboration of a new modeling approach for BLEVE overpressure, based on the calculation of the initial overpressure and radius of the blast.     

沸腾液体扩展蒸气爆炸机理及相关计算理论模型研究

剖析了沸腾液体扩展蒸气爆炸 (BLEVE)的发生、发展过程 ,阐述了其机理及相关条件 ,研究并提出了两种BLEVE火球热辐射模拟计算理论模型 ,即近地面和抬升火球模型 ,以及爆炸超压模型。与有关实验结果比较和与已有模型的对比计算表明了所建模型的有效性     

Prediction of BLEVE mechanical energy by implementation of artificial neural network

In the event of a BLEVE, the overpressure wave can cause important effects over a certain area. Several thermodynamic assumptions have been proposed as the basis for developing methodologies to predict both the mechanical energy associated to such a wave and the peak overpressure. According to a recent comparative analysis, methods based on real gas behavior and adiabatic irreversible expansion assumptions can give a good estimation of this energy. In this communication, the Artificial Neural Network (ANN) approach has been implemented to predict the BLEVE mechanical energy for the case of propane and butane. Temperature and vessel filling degree at failure have been considered as input parameters (plus vessel volume), and the BLEVE blast energy has been estimated as output data by the ANN model. A Bayesian Regularization algorithm was chosen as the three-layer backpropagation training algorithm. Based on the neurons optimization process, the number of neurons at the hidden layer was five in the case of propane and four in the case of butane. The transfer function applied in this layer was a sigmoid, because it had an easy and straightforward differentiation for using in the backpropagation algorithm. For the output layer, the number of neurons had to be one in both cases, and the transfer function was purelin (linear). The model performance has been compared with experimental values, proving that the mechanical energy of a BLEVE explosion can be adequately predicted with the Artificial Neural Network approach.     

An innovative and comprehensive approach for the consequence analysis of liquid hydrogen vessel explosions

Hydrogen is one of the most suitable solutions to replace hydrocarbons in the future. Hydrogen consumption is expected to grow in the next years. Hydrogen liquefaction is one of the processes that allows for increase of hydrogen density and it is suggested when a large amount of substance must be stored or transported. Despite being a clean fuel, its chemical and physical properties often arise concerns about the safety of the hydrogen technologies. A potentially critical scenario for the liquid hydrogen (LH₂) tanks is the catastrophic rupture causing a consequent boiling liquid expanding vapour explosion (BLEVE), with consequent overpressure, fragments projection and eventually a fireball. In this work, all the BLEVE consequence typologies are evaluated through theoretical and analytical models. These models are validated with the experimental results provided by the BMW care manufacturer safety tests conducted during the 1990's. After the validation, the most suitable methods are selected to perform a blind prediction study of the forthcoming LH₂ BLEVE experiments of the Safe Hydrogen fuel handling and Use for Efficient Implementation (SH₂IFT) project. The models drawbacks together with the uncertainties and the knowledge gap in LH₂ physical explosions are highlighted. Finally, future works on the modelling activity of the LH₂ BLEVE are suggested.     

LPG球罐BLEVE过程中超压与热耦合效应模拟研究

为评估LPG球罐发生BLEVE过程中超压与热耦合效应对化工企业抗爆控制室和避难所选址的影响,采用TNO多能法数学模型计算冲击波超压,采用多源数学模型计算火球热辐射。编写MATLAB计算程序,并应用ANSYS模拟二者破坏效应的耦合作用。LPG球罐发生BLEVE过程中,爆炸冲击波的传播速度、持续时间和火球的传播速度、持续时间不同,爆炸冲击波主要在燃料高速抛散的初期形成,之后基本与火球脱离。分别模拟计算冲击波超压和火球热辐射对抗爆控制室和避难所的影响,结果表明：抗爆控制室选址只需考虑爆炸冲击波的影响;避难所选址需要考虑冲击波超压和火球热辐射作用双重影响。在研究基础上提出,LPG球罐附近人员逃生的避难所应设置在球罐防火堤外紧邻防火堤处的地下,应具有抗震、防渗、防火、防中毒窒息等功能。人员应在BLEVE发生前进入避难所才能逃生。     

Analysis of the boiling liquid expanding vapor explosion (BLEVE) of a liquefied natural gas road tanker: The Zarzalico accident

The road accident of a tanker transporting liquefied natural gas (LNG) originated a fire and, finally, the BLEVE of the tank. This accident has been analyzed, both from the point of view of the emergency management and the explosion and fireball effects. The accidental sequence is described: fire, LNG release, further safety valves release, flames impingement on vessel unprotected wall, vessel failure mode, explosion and fireball. According to the effects and consequences observed, the thermal radiation and overpressure are estimated; a mathematical model is applied to calculate the probable mass contained in the vessel at the moment of the explosion. The peak overpressure predicted from two models is compared with the values inferred from the accident observed data. The emergency management is commented.     

BLEVE: A new approach to the superheat limit temperature

Several methods proposed for calculating the value of the superheat limit temperature were analysed. The results obtained indicate that the procedures based on the thermodynamic stability approach introduce a significant uncertainty into the final values, depending on which equation of state is used. We propose a new approach based on the energy balance in the initial liquid mass just before the explosion. The temperature obtained using this method, T_sl−E, corresponds to the situation in which the energy transferred adiabatically between the cooling liquid and the vaporising liquid fractions is at its maximum. This leads to a minimum content of energy in the remaining liquid. Although these two approaches are equivalent—the procedures based on the thermodynamic stability approach use also the minimum energy state as a criterion—the new proposed method only uses the properties of the substance to obtain T_sl−E. Thus, T_sl−E represents the behaviour of each substance as a function of its molecular structure, while this influence is lost if a simple equation of state is used. Finally, some considerations are made on the limitations of the superheat limit temperature as a criterion for establishing whether an explosion is or is not a BLEVE.     

The boiling liquid expanding vapour explosion

The boiling liquid expanding vapour explosion (BLEVE) has existed for a long time and for most of this time it has been cloaked in mystery. Several theories have been put forward to explain this very energetic event but none have been proven. This paper describes a series of tests that have recently been conducted to study this phenomenon.

The study involved ASME code automotive propane tanks with nominal capacities of 400 litres. The tanks were exposed to a combination of pool and/or torch fires. These fire conditions led to thermal ruptures, and in some cases these ruptures resulted in BLEVEs. The variables in the tests were the pressure-relief valve setting, the tank wall thickness, and the fire condition.

In total, 30 tests have been conducted, of which 22 resulted in thermal ruptures. Of those tanks that ruptured, 11 resulted in what we call BLEVEs. In this paper, we have defined a BLEVE as the explosive release of expanding vapour and boiling liquid following a catastrophic tank failure. Non-BLEVEs involved tanks that ruptured but which only resulted in a prolonged jet release.

The objective of this study was to investigate why certain tank ruptures lead to a BLEVE rather than a more benign jet-type release. Data are presented to show how wall temperature, wall thickness, liquid temperature and fill level contribute to the BLEVE process.     

Blast overpressures from medium scale BLEVE tests

The measured blast overpressures from recent tests involving boiling liquid expanding vapour explosions (BLEVE) has been studied. The blast data came from tests where 0.4 and 2 m³ ASME code propane tanks were exposed to torch and pool fires. In total almost 60 tanks were tested, and of these nearly 20 resulted in catastrophic failures and BLEVEs. Both single and two-step BLEVEs were observed in these tests. This paper presents an analysis of the blast overpressures created by these BLEVEs. In addition, the blast overpressures from a recent full scale fire test of a rail tank car is included in the analysis.The results suggest that the liquid energy content did not contribute to the shock overpressures in the near or far field. The liquid flashing and expansion does produce a local overpressure by dynamic pressure effects but it does not appear to produce a shock wave. The shock overpressures could be estimated from the vapour energy alone for all the tests considered. This was true for liquid temperatures at failure that were below, at and above the atmospheric superheat limit for propane. Data suggests that the two step type BLEVE produces the strongest overpressure. The authors give their ideas for this observation.The results shown here add some limited evidence to support previous researchers claims that the liquid flashing process is too slow to generate a shock. It suggests that liquid temperatures at or above the Tsl do not change this. The expansion of the flashing liquid contributes to other hazards such as projectiles, and close in dynamic pressure effects. Of course BLEVE releases in enclosed spaces such as tunnels or buildings have different hazards.     

Assessment of an accidental vapour cloud explosion: Lessons from the Indian Oil Corporation Ltd. accident at Jaipur,India

On 29 October 2009, at 19:30 IST, a devastating vapour cloud explosion occurred in a large fuel storage area at the Indian Oil Corporation (IOC) Depot in Jaipur, India, generating significant blast pressure. As a consequence of this explosion, the entire installation was destroyed, buildings in the immediate vicinity were heavily damaged, and windowpane breakages were found up to 2 km from the terminal. The IOC estimated that the total loss from the fire and explosion was approximately INR 2800 million.Ironically, as a storage site, the Jaipur terminal was not highly congested, and thus was not considered to have adequate potential for a vapour cloud explosion (VCE). Nevertheless, the prima facie evidences indicate that this was a case of VCE. Therefore, the main objective of this study is to quantify the potential overpressures due to vapour cloud explosions (VCEs) using the Process Hazard Analysis DNV Norway based PHAST 6.51 Software. The results are validated by the extent of the damage that had occurred. The estimation of the VCE shows that a maximum 1.0 bar overpressure was generated in the surrounding area. The initial assessment of the accident data roughly estimates the release mode, time, and amount of vaporized fuel. A more accurate estimate has been obtained by modelling the dispersion of vapour clouds in the surrounding atmosphere, which reveals trends and relationships for the occurrence of vapour cloud explosions.     

Fire and explosion hazard analysis during surface transport of liquefied petroleum gas (LPG): A case study of LPG truck tanker accident in Kannur,Kerala, India

This paper presents an analysis and simulation of an accident involving a liquefied petroleum gas (LPG) truck tanker in Kannur, Kerala, India. During the accident, a truck tanker hit a divider and overturned. A crack in the bottom pipe caused leakage of LPG for about 20 min forming a large vapor cloud, which got ignited, creating a fireball and a boiling liquid expanding vapor explosion (BLEVE) situation in the LPG tank with subsequent fire and explosion. Many fatalities and injuries were reported along with burning of trees, houses, shops, vehicles, etc. In the present study, ALOHA (Area Locations of Hazardous Atmospheres) and PHAST (Process Hazard Analysis Software Tool) software have been used to model and simulate the accident scenario. Modeling and simulation results of the fireball, jet flame radiation and explosion overpressure agree well with the actual loss reported from the site. The effects of the fireball scenario were more significant in comparison to that of the jet fire scenario.     

Experimental study on unconfined methane explosion: Explosion characteristics and overpressure prediction method

Explosion accidents have become the main threat for the high-efficiency use of cleaner gas energy sources, such as natural gas. During an explosion, obstacle causing flame acceleration is the main reason for the increase of the explosion overpressure, which still remains to be fully understood. In this research, field experiments were conducted in a 1 m³ cubic frame apparatus to investigate the effect of built-in obstacles on unconfined methane explosion. Cage-like obstacles were constructed using square steel rods with different cross section size. The results demonstrated that the flame could get accelerated due to the hydrodynamic instability and obstacle-induced turbulence, which enhanced the explosion overpressure. In the near field, the overpressure wave travelled slower and the maximum overpressure could almost keep constant. Reducing the cross section size, or increasing the obstacle height or the obstacle number per layer could determine the rise of the maximum overpressure, the maximum pressure rising rate and the overpressure impulse. For uniformly constructed obstacles, self-similar theory was chosen to measure the influence of the hydrodynamic instability, and a parameter β was adopted to measure the flame acceleration caused by obstacle-induced turbulence, the value of which was 2 in this research. Based on the acoustic theory, an overpressure prediction model was proposed and the predicted results agreed with the measured values better than previous models, such as TNT equivalency model and TNO multi-energy model.     

BLEVE: The case of water and a historical survey

After a short update of the current more accepted definition of BLEVE, the special features of water BLEVEs are analyzed. The stronger overpressure wave generated in the case of water as compared to that of other substances is justified in terms of volume change. Through a comparison with liquefied pressurized propane, three possibilities are analyzed: the simultaneous contribution of both the liquid and the preexisting vapor, the contribution of the liquid flash vaporization, and the contribution of the pre-existing vapor. Also a historical survey on a set of 202 BLEVE accidents –the largest sample of BLEVE accidents surveyed until now– is presented. LPG was the most common substances in this set of accidents. However, water and LNG (11% of water and 4% of LNG in the studied cases) have also been involved. Impact failure (44.8%) and human factor (30.3%) were the most common causes of BLEVEs. Transport, storage, process plants, and transfer were the activities in which more accidents occurred.     

Influence of built-in obstacles on unconfined vapor cloud explosion

The obstacle structure in the vapor cloud has a significant influence on the gas explosion. Obstacles could not only lead to the acceleration of flame, but also they may occupy some space, thus affecting the amount of combustible gas. In this paper, a new two-step method was proposed to respectively study the effects of the obstacles amount and volume blockage ratio (VBR) on the gas explosion by using Computation Fluid Dynamic software AutoReaGas, and the obstacles in the vapor cloud were set to “Solid” instead of “Subgrid”. Based on the results and analysis, it is found that the peak overpressure and the maximum combustion rate rise with the increase of the number of obstacles for a single VBR, which indicated that the vapor cloud explosion of more obstacles was more dangerous for a single VBR. However, under a single number of obstacles, the peak overpressure and the maximum combustion rate increase firstly and then decrease as VBR increases and reach the highest at the VBR of 0.74, which indicated that the intensity of vapor cloud explosion reach a peak at a certain VBR in the middle instead of the largest. In addition, the existence and structure of obstacles have little effect on the size of explosion fireball when the size and concentration of combustible gas cloud are the same.     

Assessing the hazards from a BLEVE and minimizing its impacts using the inherent safety concept

Many worlds' major process industry accidents are due to BLEVE such as at Feyzin, France, 1966 and San Juan Ixhuatepec, Mexico City, 1984. One of the approaches to eliminate or minimize such accidents is by the implementation of inherently safer design concept. This concept is best implemented where the consequence of BLEVE can be evaluated at the preliminary design stage, and necessary design improvements can be done as early as possible. Thus, the accident could be avoided or minimized to as low as reasonably practicable (ALARP) without resorting to a costly protective system. However, the inherent safety concept is not easy to implement at the preliminary design stage due to lack of systematic technique for practical application. To overcome these hurdles, this paper presents a new approach to assess process plant for the potential BLEVE at the preliminary design stage and to allow modifications using inherent safety principles in order to avoid or minimize major accidents. A model known as Inherent Fire Consequence Estimation Tool (IFCET) is developed in MS Excel spreadsheet to evaluate BLEVE impacts based on overpressure, radiation heat flux and missile effects. In this study, BLEVE impacts are the criteria used as the decision-making for the acceptability of the design. IFCET is integrated with iCON process design simulator for ease of data transfer and quick assessment of potential BLEVE during the design simulation stage. A case study was conducted to assess of potential BLEVE from a propane storage vessel at the design simulation stage using this new approach. The finding shows promising results that this approach has a potential to be developed as a practical tool.     

瓦斯爆炸后空间温度分布及热危害区域分析研究

为了获得瓦斯爆炸引发次生灾害的特性参数,建立了超压预测模型及爆炸后空气温度衰减模型,并结合实验数据进行了验证。结果表明:依据所建立的超压修正模型,不同浓度和体积下的超压在爆源附近呈对数形式快速下降,之后缓慢趋向平稳;基于模型修正的爆炸超压计算公式,能够很好的对各个情形的瓦斯爆炸超压进行计算,吻合较好。对初始瓦斯体积相对较小的情形吻合度很高,对于初始体积大的瓦斯爆炸超压在100 m附近会出现一定误差,但有一定指导意义。瓦斯爆炸热危害区域的研究,对瓦斯爆炸次生灾害的防治工作具有重要意义。     

The application of pressure–impulse curves in a blast exceedance analysis

The magnitude of damage due to a vapor cloud explosion can be estimated in many ways, ranging from look-up tables to quantitative risk analysis. An explosion overpressure analysis is a routine part of compliance with the American Petroleum Institute (API) Recommended Practice (RP) 752 when evaluating occupied buildings in a facility that processes flammable or reactive materials. In many cases, a risk-based approach is useful because consequence modeling studies often indicate major problems for buildings at existing facilities. One of the most common risk-based methods, overpressure exceedance, incorporates a wide range of potential explosion scenarios coupled with the probability of each event to develop the probability of exceeding a given overpressure at specific locations. But this and other methods that only use overpressure may not represent an accurate building response. By combining the risk-based methodology of the exceedance analysis with pressure and impulse data in the form of pressure–impulse (P–I) curves, a better measure of building damage can be generated. P–I curves for blast loading determination have been in use for decades, and allow the user to determine levels of damage based on a predicted overpressure and its corresponding impulse. Curves have been published for entire buildings, individual structural members, window breakage, and even consequences to humans. This paper will explore application of P–I curves for building damage, and will highlight some of the benefits, as well as some of the potential problems, of using P–I curves.     

重大危险源区域事故应急非结构化模糊决策应用研究

针对目前我国应对重大危险源突发事故的管理和决策主要依赖于相关领导或专家掌握的知识及经验的现状,将非结构化模糊决策方法(Non-structural Fuzzy Decision Method,NSFDM)和事故后果模拟方法相结合,以区域范围内受重大危险源潜在事故影响的企业为决策对象,以减小事故影响范围,降低事故严重程度为目标,建立起重大危险源区域事故应急决策的多准则决策方法,以期帮助安监职能部门优化配置应急救援资源,提高应急响应绩效,减少国家和人民的经济和财产损失。以广州市某公司丙烷储罐区为实例,在对其进行沸腾液体扩展蒸气爆炸(Boiling Liquid Expanding Va-por Explosion,BLEVE)事故模拟的基础上,运用非结构化模糊决策方法,对该丙烷储罐区BLEVE事故的处理,提供了应急决策支持。     

Gas explosion analysis of safety gap effect on the innovating FLNG vessel with a cylindrical platform

After investigating gas dispersion on a cylindrical Floating Liquefied Natural Gas (FLNG) platform (Li et al, 2016), this second article focuses on assessment of gas explosion by using Computational Fluid Dynamics (CFD). Gas explosion simulations are carried out to evaluate the explosion overpressure mitigating effect of safety gap. The Data-dump technique, which is an effective tool in resetting turbulence length scale in gas explosion overpressure calculation, is applied to ensure simulation accuracy for the congestion scenario with safety gap. Two sets of different safety gaps are designed to investigate the safety gap on the cylindrical FLNG platform, the overall results indicate that the safety gap is effective in reducing overpressure in two adjacent congestions. However, for the explosion scenario where the flame is propagating through several safety gaps to the far field congestion, the safety gap mitigates overpressure only in certain explosion protecting targets. Two series of artificial configurations are modeled to further investigate the explosion scenarios with more than two safety gaps in one direction. It is concluded that the optimal safety gap design in overpressure mitigation for the cylindrical FLNG platform is to balance the safety gap distance ratio in the congested regions.