Predicting the elemental compositions of solid waste using ATR-FTIR and machine learning

● A method based on ATR-FTIR and ML was developed to predict CHNS contents in waste. ● Feature selection methods were used to improve models’ prediction accuracy. ● The best model predicted C, H, and N contents with accuracy R ² ≥ 0.93, 0.87, 0.97. ● Some suitable models showed insensitivity to spectral noise. ● Under moisture interference, the models still had good prediction performance. Elemental composition is a key parameter in solid waste treatment and disposal. This study has proposed a method based on infrared spectroscopy and machine learning algorithms that can rapidly predict the elemental composition (C, H, N, S) of solid waste. Both noise and moisture spectral interference that may occur in practical application are investigated. By comparing two feature selection methods and five machine learning algorithms, the most suitable models are selected. Moreover, the impacts of noise and moisture on the models are discussed, with paper, plastic, textiles, wood, and leather as examples of recyclable waste components. The results show that the combination of the feature selection and K-nearest neighbor (KNN) approaches exhibits the best prediction performance and generalization ability. Particularly, the coefficient of determination (R²) of the validation set, cross validation and test set are higher than 0.93, 0.89, and 0.97 for predicting the C, H, and N contents, respectively. Further, KNN is less sensitive to noise. Under moisture interference, the combination of feature selection and support vector regression or partial least-squares regression shows satisfactory results. Therefore, the elemental compositions of solid waste are quickly and accurately predicted under noise and moisture disturbances using infrared spectroscopy and machine learning algorithms.     

Water quality prediction of copper-molybdenum mining-beneficiation wastewater based on the PSO-SVR model

● Data acquisition and pre-processing for wastewater treatment were summarized. ● A PSO-SVR model for predicting COD_eff in wastewater was proposed. ● The COD_eff prediction performances of the three models in the paper were compared. ● The COD_eff prediction effects of different models in other studies were discussed. The mining-beneficiation wastewater treatment is highly complex and nonlinear. Various factors like influent quality, flow rate, pH and chemical dose, tend to restrict the effluent effectiveness of mining-beneficiation wastewater treatment. Chemical oxygen demand (COD) is a crucial indicator to measure the quality of mining-beneficiation wastewater. Predicting COD concentration accurately of mining-beneficiation wastewater after treatment is essential for achieving stable and compliant discharge. This reduces environmental risk and significantly improves the discharge quality of wastewater. This paper presents a novel AI algorithm PSO-SVR, to predict water quality. Hyperparameter optimization of our proposed model PSO-SVR, uses particle swarm optimization to improve support vector regression for COD prediction. The generalization capacity tested on out-of-distribution (OOD) data for our PSO-SVR model is strong, with the following performance metrics of root means square error (RMSE) is 1.51, mean absolute error (MAE) is 1.26, and the coefficient of determination (R²) is 0.85. We compare the performance of PSO-SVR model with back propagation neural network (BPNN) and radial basis function neural network (RBFNN) and shows it edges over in terms of the performance metrics of RMSE, MAE and R², and is the best model for COD prediction of mining-beneficiation wastewater. This is because of the less overfitting tendency of PSO-SVR compared with neural network architectures. Our proposed PSO-SVR model is optimum for the prediction of COD in copper-molybdenum mining-beneficiation wastewater treatment. In addition, PSO-SVR can be used to predict COD on a wide variety of wastewater through the process of transfer learning.     

Biodegradation of waste refrigerator polyurethane by mealworms

● Waste refrigerator polyurethane (WRPU) was ingested and biodegraded by mealworms. ● The carbon in WRPU-based frass was lower than that in WRPU. ● Urethane groups in WRPU were broken down after ingestion by mealworms. ● Thermal stability of WRPU-based frass were deteriorated compared to that of WRPU. ● Gut microbiomes of mealworms fed using WRPU were distinct from that fed using bran. Refrigerator insulation replacement results in discarding a large amount of waste refrigerator polyurethane (WRPU). Insect larvae like mealworms have been used to biodegrade pristine plastics. However, knowledge about mealworms degrading WRPU is scarce. This study presents an in-depth investigation of the degradation of WRPU by mealworms using the micro-morphology, composition, and functional groups of WRPU and the egested frass characteristics. It was found that the WRPU debris in frass was scoured, implying that WRPU was ingested and degraded by mealworms. The carbon content of WRPU-based frass was lower than that of WRPU, indicating that mealworms utilized WRPU as a carbon source. The urethane groups in WRPU were broken, and benzene rings’ C=C and C–H bonds in the isocyanate disappeared after being ingested by mealworms. Thermal gravimetric-differential thermal gravimetry analysis showed that the weight loss temperature of WRPU-based frass was 300 °C lower than that of WRPU, indicating that the thermal stability of WRPU deteriorated after being ingested. The carbon balance analysis confirmed that carbon in the ingested WRPU released as CO₂ increased from 18.84 % to 29.80 %, suggesting that WRPU was partially mineralized. The carbon in the mealworm biomass ingesting WRPU decreased. The possible reason is that WRPU does not supply sufficient nutrients for mealworm growth, and the impurities and odor present in WRPU affect the appetite of the mealworms. The microbial community analysis indicated that WRPU exerts a considerable effect on the gut microorganism of mealworms. These findings confirm that mealworms degrade WRPU.     

Is atmospheric oxidation capacity better in indicating tropospheric O3 formation?

● This study summarizes and evaluates different approaches that indicate O₃ formation. ● Isopleth and sensitivity methods are useful but have many prerequisites. ● AOC is a better indicator of photochemical reactions leading to O₃ formation. Tropospheric ozone (O₃) concentration is increasing in China along with dramatic changes in precursor emissions and meteorological conditions, adversely affecting human health and ecosystems. O₃ is formed from the complex nonlinear photochemical reactions from nitrogen oxides (NO_x = NO + NO₂) and volatile organic compounds (VOCs). Although the mechanism of O₃ formation is rather clear, describing and analyzing its changes and formation potential at fine spatial and temporal resolution is still a challenge today. In this study, we briefly summarized and evaluated different approaches that indicate O₃ formation regimes. We identify that atmospheric oxidation capacity (AOC) is a better indicator of photochemical reactions leading to the formation of O₃ and other secondary pollutants. Results show that AOC has a prominent positive relationship to O₃ in the major city clusters in China, with a goodness of fit (R²) up to 0.6. This outcome provides a novel perspective in characterizing O₃ formation and has significant implications for formulating control strategies of secondary pollutants.     

Mechanism and characterization of microplastic aging process: A review

● Methods for estimating the aging of environmental micro-plastics were highlighted. ● Aging pathways & characterization methods of microplastics were related and reviewed. ● Possible approaches to reduce the contamination of microplastics were proposed. ● The prospect and deficiency of degradable plastics were analyzed. With the increasing production of petroleum-based plastics, the problem of environmental pollution caused by plastics has aroused widespread concern. Microplastics, which are formed by the fragmentation of macro plastics, are bio-accumulate easily due to their small size and slow degradation under natural conditions. The aging of plastics is an inevitable process for their degradation and enhancement of adsorption performance toward pollutants due to a series of changes in their physiochemical properties, which significantly increase the toxicity and harm of plastics. Therefore, studies should focus on the aging process of microplastics through reasonable characterization methods to promote the aging process and prevent white pollution. This review summarizes the latest progress in natural aging process and characterization methods to determine the natural aging mechanism of microplastics. In addition, recent advances in the artificial aging of microplastic pollutants are reviewed. The degradation status and by-products of biodegradable plastics in the natural environment and whether they can truly solve the plastic pollution problem have been discussed. Findings from the literature pointed out that the aging process of microplastics lacks professional and exclusive characterization methods, which include qualitative and quantitative analyses. To lessen the toxicity of microplastics in the environment, future research directions have been suggested based on existing problems in the current research. This review could provide a systematic reference for in-depth exploration of the aging mechanism and behavior of microplastics in natural and artificial systems.     

Combination of steam-enhanced extraction and electrical resistance heating for efficient remediation of perchloroethylene-contaminated soil: Coupling merits and energy consumption

● Coupling merits of SEE and ERH were explored by a laboratory-scale device. ● SEE promotes the soil electrical conductivity and ERH process. ● Preheating soil by ERH improves the soil permeability and SEE. ● Combined method is more energy-efficient for perchloroethylene extraction. In situ thermal desorption (ISTD) technology effectively remediates soil contaminated by dense nonaqueous phase liquids (DNAPLs). However, more efforts are required to minimize the energy consumption of ISTD technology. This study developed a laboratory-scale experimental device to explore the coupling merits of two traditional desorption technologies: steam-enhanced extraction (SEE) and electrical resistance heating (ERH). The results showed that injecting high-density steam (> 1 g/min) into loam or clay with relatively high moisture content (> 13.3%) could fracture the soil matrix and lead to the occurrence of the preferential flow of steam. For ERH alone, the electrical resistance and soil moisture loss were critical factors influencing heating power. When ERH and SEE were combined, preheating soil by ERH could increase soil permeability, effectively alleviating the problem of preferential flow of SEE. Meanwhile, steam injection heated the soil and provided moisture for maintaining soil electrical conductivity, thereby ensuring power stability in the ERH process. Compared with ERH alone (8 V/cm) and SEE alone (1 g/min steam), the energy consumption of combined method in remediating perchloroethylene-contaminated soil was reduced by 39.3% and 52.9%, respectively. These findings indicate that the combined method is more favorable than ERH or SEE alone for remediating DNAPL-contaminated subsurfaces when considering ISTD technology.     

NiB2O4 (B = Mn or Co) catalysts for NH3-SCR of NOx at low-temperature in microwave field

● Microwave-assisted catalytic NH₃-SCR reaction over spinel oxides is carried out. ● SCR reaction temperature is tremendously lowered in microwave field. ● NO conversion of NiMn₂O₄ is highly up to 90.6% at 70°C under microwave heating. Microwave-assisted selective catalytic reduction of nitrogen oxides (NO_x) was investigated over Ni-based metal oxides. The NiMn₂O₄ and NiCo₂O₄ catalysts were synthesized by the co-precipitation method and their activities were evaluated as potential candidate catalysts for low-temperature NH₃-SCR in a microwave field. The physicochemical properties and structures of the catalysts were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM), N₂-physisorption, NO adsorption-desorption in the microwave field, H₂-temperature programmed reduction (H₂-TPR) and NH₃-temperature programmed desorption (NH₃-TPD). The results verified that microwave radiation reduced the reaction temperature required for NH₃-SCR compared to conventional heating, which needed less energy. For the NiMn₂O₄ catalyst, the catalytic efficiency exceeded 90% at 70 °C and reached 96.8% at 110 °C in the microwave field. Meanwhile, the NiMn₂O₄ also exhibited excellent low-temperature NH₃-SCR reaction performance under conventional heating conditions, which is due to the high BET specific surface area, more suitable redox property, good NO adsorption-desorption in the microwave field and rich acidic sites.     

Adsorption and desorption of steroid hormones on saline soil

● Organic matter content significantly affected adsorption of E2/EE2 on saline soil. ● EE2 possessed higher competition intensity for adsorption sites than E2. ● The adsorption of E2/EE2 on saline soil was a spontaneous exothermic process. ● Desorption capacity of EE2/E2 accounted for 40%/78% of the total adsorption capacity. Soil organic matter content was the main driving factor affecting adsorption and desorption process of 17β-estradiol (E2) and 17α-ethynylestradiol (EE2) on saline soil. The adsorption and desorption of E2 and EE2 on three saline soils showed the similar behavior that soil with the highest organic content possessed the highest adsorption capacity and the lowest desorption capacity for E2 and EE2. The adsorption capacity of untreated soil samples (with organic matter) was larger than that of soil samples without organic matter. For soil with the largest adsorption capacity, adsorption capacity of E2/EE2 on the untreated soil and soil colloid (with organic matter) respectively reached 0.15/0.30 μg/g and 0.16/0.33 μg/g while the soil and soil colloid without organic matter hardly adsorbed pollutants. The adsorption capacity of E2/EE2 at the initial concentration of 100 μg/L was 25/15 times higher than that at the initial concentration of 5 μg/L. E2 and EE2 had the same adsorption sites on saline soil while EE2 possessed higher competition intensity for adsorption sites than E2. Pseudo-first-order model (R² = 0.995–0.986) and Langmuir model (R² = 0.989–0.999) could better fit the adsorption process of E2 or EE2. The thermodynamic study further showed that the adsorption of E2/EE2 on saline soil was a spontaneous exothermic process. The desorption capacity of EE2/E2 accounted for 40%/78% of the total adsorption capacity to possibly exert potential risk to the groundwater. The variation of the salinity led to the variation of soil organic carbon which subsequently changed the adsorption and desorption behaviors of endocrine disrupting chemicals in coastal saline soil. This study provides a new insight on the interfacial behavior of endocrine disrupting chemicals on saline soil.     

Electroconductive RGO-MXene membranes with wettability-regulated channels: improved water permeability and electro-enhanced rejection performance

● Electroconductive RGO-MXene membranes were fabricated. ● Wettable membrane channels were established between RGO and MXene nanosheets. ● Hydrophilic MXene reduces the resistance of water entering the membrane channels. ● Water permeance of RGO-MXene membrane is 16.8 times higher than that of RGO membrane. ● Electro-assistance can enhance the dye rejection performance of RGO-MXene membrane. Reduced graphene oxide (RGO) membranes are theoretically more conducive to the rapid transport of water molecules in their channels compared with graphene oxide (GO) membranes, as they have fewer oxygen-containing functional groups and more non-oxidized regions. However, the weak hydrophilicity of RGO membranes inhibits water entry into their channels, resulting in their low water permeability. In this work, we constructed wettable RGO-MXene channels by intercalating hydrophilic MXene nanosheets into the RGO membrane for improving the water permeance. The RGO-MXene composite membrane exhibits high pure water permeance of 62.1 L/(m²·h·bar), approximately 16.8 times that of the RGO membrane (3.7 L/(m²·h·bar)). Wettability test results and molecular dynamics simulations suggest that the improved water permeance results from the enhanced wettability of RGO-MXene membrane and increased rate of water molecules entering the RGO-MXene channels. Benefiting from good conductivity, the RGO-MXene membrane with electro-assistance exhibits significantly increased rejection rates for negatively charged dyes (from 56.0% at 0 V to 91.4% at 2.0 V for Orange G) without decreasing the permeate flux, which could be attributed to enhanced electrostatic repulsion under electro-assistance.     

Self-catalytic pyrolysis thermodynamics of waste printed circuit boards with co-existing metals

● The co-existing metals in WPCBs has positive catalytic influence in pyrolysis. ● Cu, Fe, Ni can promote reaction progress and reduce the apparent activation energy. ● Ni play better role in promoting WPCB pyrolysis reaction. Waste printed circuit boards (WPCBs) are generated increasingly recent years with the rapid replacement of electric and electronic products. Pyrolysis is considered to be a potential environmentally-friendly technology for recovering organic and metal resources from WPCBs. Thermogravimetric analysis and kinetic analysis of WPCBs were carried out in this study. It showed that the co-existing metals (Cu, Fe, Ni) in WPCBs have positive self-catalytic influence during the pyrolysis process. To illustrate their catalytic effects, the apparent activation energy was calculated by differential model. Contributions of different reactions during catalytic pyrolysis process was studied and the mechanism function was obtained by Šesták-Berggren model. The results showed that Cu, Fe, Ni can promote the reaction progress and reduce the apparent activation energy. Among the three metals, Ni plays better catalytic role than Cu, then Fe. This work provides theoretical base for understanding the three metals’ catalytic influence during the pyrolysis of non-metal powders in WPCBs.     

Electroreduction of hexavalent chromium using a porous titanium flow-through electrode and intelligent prediction based on a back propagation neural network

● Titanium-based flow-through electrode achieved high Cr(VI) reduction efficiency. ● Flow-through pattern enhanced the mass transfer and reduced cathodic polarization. ● BPNN predicted the optimal electroreduction conditions of flow-through cell. Flow-through electrodes have been demonstrated to be effective for electroreduction of Cr(VI), but shortcomings are tedious preparation and short lifetimes. Herein, porous titanium available in the market was studied as a flow-through electrode for Cr(VI) electroreduction. In addition, the intelligent prediction of electrolytic performance based on a back propagation neural network (BPNN) was developed. Voltametric studies revealed that Cr(VI) electroreduction was a diffusion-controlled process. Use of the flow-through mode achieved a high limiting diffusion current as a result of enhanced mass transfer and favorable kinetics. Electroreduction of Cr(VI) in the flow-through system was 1.95 times higher than in a parallel-plate electrode system. When the influent (initial pH 2.0 and 106 mg/L Cr(VI)) was treated at 5.0 V and a flux of 51 L/(h·m²), a reduction efficiency of ~99.9% was obtained without cyclic electrolysis process. Sulfate served as the supporting electrolyte and pH regulator, as reactive CrSO₇²⁻ species were formed as a result of feeding HSO₄⁻. Cr(III) was confirmed as the final product due to the sequential three-electron transport or disproportionation of the intermediate. The developed BPNN model achieved good prediction accuracy with respect to Cr(VI) electroreduction with a high correlation coefficient (R² = 0.943). Additionally, the electroreduction efficiencies for various operating inputs were predicted based on the BPNN model, which demonstrates the evolutionary role of intelligent systems in future electrochemical technologies.     

Nonpolar cross-stacked super-aligned carbon nanotube membrane for efficient wastewater treatment

● A novel nonpolar super-aligned carbon nanotube (SACNT) membrane was prepared. ● SACNT membranes achieved smoother and more uniform structures. ● SACNT membranes have inert chemistry and unique nonpolar wetting feature. ● SACNT membranes exhibit superior separation and antifouling capabilities. ● SACNT membranes achieved superior oil/water separation efficiency. Membrane separation technology has made great progress in various practical applications, but the unsatisfactory separation performance of prevailing membrane materials hampers its further sustainable growth. This study proposed a novel nonpolar super-aligned carbon nanotube (SACNT) membrane, which was prepared with a layer-by-layer cross-stacking method. Through controlling the number of stacked SACNT layers, three kinds of SACNT membranes (SACNT_200, SACNT_300, and SACNT_400) were prepared. Systematic characterizations and filtration tests were performed to investigate their physico-chemical properties, surface wetting behavior, and filtration performance. Compared with two commercial membranes (Com_0.22 and Com_0.45), all the SACNT membranes achieved smoother and more uniform structures. Due to the hexagonal graphene structure of CNTs, the surface chemistry of the SACNT membranes is simple and inert, thereby potentially eliminating the covalent-bonding-induced membrane fouling. Besides, the SACNT membranes exhibited a typical nonpolar wetting behavior, with high contact angles for polar liquids (water: ~124.9°–126.5°; formamide: ~80.0°–83.9°) but low contact angles for nonpolar diiodomethane (~18.8°–20.9°). This unique nonpolar feature potentially leads to weak interactions with polar substances. Furthermore, compared with the commercial membranes, the SACNT membranes obtained a significantly higher selectivity while achieving a comparable or higher permeability (depending on the number of stacked layers). Moreover, the SACNT membranes exhibited superior separation performance in various application scenarios, including municipal wastewater treatment (> 2.3 times higher cleaning efficiency), electro-assistant fouling inhibition (or even self-cleaning), and oil/water separation (> 99.2 % of separation efficiency), suggesting promising application prospects in various fields.     

Distribution,enrichment mechanism and risk assessment for fluoride in groundwater: a case study of Mihe-Weihe River Basin,China

● High fluorine is mainly HCO₃·Cl-Na and HCO₃-Na type. ● F⁻ decreases with the increase of depth to water table. ● High fluoride is mainly affected by fluorine-containing minerals and weak alkaline. ● Fluorine pollution is mainly in the north near Laizhou Bay (wet season > dry season). ● Groundwater samples have a high F⁻ health risk (children > adults). Due to the unclear distribution characteristics and causes of fluoride in groundwater of Mihe-Weihe River Basin (China), there is a higher risk for the future development and utilization of groundwater. Therefore, based on the systematic sampling and analysis, the distribution features and enrichment mechanism for fluoride in groundwater were studied by the graphic method, hydrogeochemical modeling, the proportionality factor between conventional ions and factor analysis. The results show that the fluorine content in groundwater is generally on the high side, with a large area of medium-fluorine water (0.5–1.0 mg/L), and high-fluorine water is chiefly in the interfluvial lowlands and alluvial-marine plain, which mainly contains HCO₃·Cl-Na- and HCO₃-Na-type water. The vertical zonation characteristics of the fluorine content decrease with increasing depth to the water table. The high flouride groundwater during the wet season is chiefly controlled by the weathering and dissolution of fluorine-containing minerals, as well as the influence of rock weathering, evaporation and concentration. The weak alkaline environment that is rich in sodium and poor in calcium during the dry season is the main reason for the enrichment of fluorine. Finally, an integrated assessment model is established using rough set theory and an improved matter element extension model, and the level of groundwater pollution caused by fluoride in the Mihe-Weihe River Basin during the wet and dry seasons in the Shandong Peninsula is defined to show the necessity for local management measures to reduce the potential risks caused by groundwater quality.     

Electrocatalytic reduction of nitrate using Pd-Cu modified carbon nanotube membranes

● Pd-Cu modified CNT membranes were prepared successfully by electrodeposition method. ● The deposition voltage and deposition time were optimized for Pd-Cu co-deposition. ● NO₃⁻-N was removed efficiently from water by Pd-Cu modified CNT membranes. ● The presence of dissolved oxygen did not affect the nitrate reduction performance. ● Mass transfer rate was promoted significantly with the increase in membrane flux. Excessive nitrate in water is harmful to the ecological environment and human health. Electrocatalytic reduction is a promising technology for nitrate removal. Herein, a Pd-Cu modified carbon nanotube membrane was fabricated with an electrodeposition method and used to reduce nitrate in a flow-through electrochemical reactor. The optimal potential and duration for codeposition of Pd and Cu were −0.7 V and 5 min, respectively, according to linear scan voltammetry results. The membrane obtained with a Pd:Cu ratio of 1:1 exhibited a relatively high nitrate removal efficiency and N₂ selectivity. Nitrate was almost completely reduced (~99 %) by the membrane at potentials lower than −1.2 V. However, −0.8 V was the optimal potential for nitrate reduction in terms of both nitrate removal efficiency and product selectivity. The nitrate removal efficiency was 56.2 %, and the N₂ selectivity was 23.8 % for the Pd:Cu=1:1 membrane operated at −0.8 V. Nitrate removal was enhanced under acidic conditions, while N₂ selectivity was decreased. The concentrations of Cl⁻ ions and dissolved oxygen showed little effect on nitrate reduction. The mass transfer rate constant was greatly improved by 6.6 times from 1.14 × 10⁻³ m/h at a membrane flux of 1 L/(m²·h) to 8.71 × 10⁻³ m/h at a membrane flux of 15 L/(m²·h), which resulted in a significant increase in the nitrate removal rate from 13.6 to 133.5 mg/(m²·h). These findings show that the Pd-Cu modified CNT membrane is an efficient material for nitrate reduction.     

Impacts of backwashing on micropollutant removal and associated microbial assembly processes in sand filters

● Backwashing in sand filters with 2-h and 4-h EBCTs was simulated. ● Removal efficiency of five micropollutants recovered within 2 d at 2-h EBCT. ● Active biomass of sand filters recovered within 2 d under two EBCTs. ● Microbial composition gradually recovered to pre-backwashing level at 2-h EBCT. ● Recovered microbes only accounted for 15.55 %–25.69 % in the sand filters at 4-h EBCT. Backwashing is crucial for preventing clogging of sand filters. However, few studies have investigated the effect of backwashing on micropollutant removal and the dynamic changes in the microbial community in sand filters. Here, we used a series of manganese and quartz sand filters under empty bed contact times (EBCTs) of 2 h and 4 h to explore variations in micropollutant degradation and temporal dynamics of the microbial community after backwashing. The results showed that the removal efficiencies of caffeine, sulfamethoxazole, sulfadiazine, trimethoprim, atrazine, and active biomass recovered within 2 d after backwashing in both types of sand filters at 2-h EBCT, but the recovery of sulfadiazine and trimethoprim was not observed at 4-h EBCT. Moreover, the removal efficiency of atenolol increased after backwashing in the manganese sand filters, whereas maintained almost complete removal efficiency in the quartz sand filters at both EBCTs. Pearson correlation analysis indicated that microbial community composition gradually recovered to the pre-backwashing level (R increased from 0.53 to 0.97) at 2-h EBCT, but shifted at 4-h EBCT (R < 0.25) after backwashing. Furthermore, the compositions of the recovered, depleted, and improved groups of microbes were distinguished by applying hierarchical clustering to the differentially abundant amplicon sequence variants. The cumulative relative abundance of recovered microbes at 2-h EBCT was 82.76 % ± 0.43 % and 46.82 % ± 4.34 % in the manganese and quartz sand filters, respectively. In contrast, at 4-h EBCT, the recovered microbes dropped to 15.55 %–25.69 % in both types of sand filters.     

Resource utilization of typical biomass wastes as biochars in removing plasticizer diethyl phthalate from water: characterization and adsorption mechanisms

● Six largely produced agricultural biomass wastes were pyrolyzed into biochars. ● Feedstock type significantly determined physiochemical properties of biochars. ● The biochars showed powerful adsorption capabilities to Plasticizer DEP. ● Giant reed biochar with higher DEP adsorption was a prominent sorbent. Plastic pollution as a global environmental issue has become a research hotspot, among which the removal of inherent plasticizer (e.g., phthalic acid esters, PAEs) received increasing attention. However, the effects of biochars derived from different feedstocks on the adsorption of PAEs are poorly understood. Thus, the characteristics of biochars derived from six largely produced biomass wastes in China at 400 °C, as well as their performance in adsorption of diethyl phthalate (DEP), one of frequently detected PAEs in aqueous environment, were investigated. The results indicated that the variation in feedstock type showed significant changes in the properties (e.g., porosity, specific surface area, surface functional groups) of biochars, which affected DEP adsorption and desorption. Pseudo-second order and Freundlich models fitted the adsorption data well, and adsorption mechanisms mainly included hydrophobic effect, followed by micropore filling, hydrogen bonding, and π-π EDA interactions. Adsorption thermodynamics revealed that the adsorption was a spontaneous and exothermic the adsorption capacities of DEP on these biochars slightly decreased with the increasing pH but increased with the increasing ionic strength. Among these biochars, the giant reed biochar with relatively higher DEP adsorption and low desorption exhibited the great efficiency for DEP removal as an environment-friendly sorbent. These results highlighted the significant roles of micropore filling and hydrogen bond in determining adsorption capacity of designed biochars prepared from selecting suitable agricultural straws and wetland plant waste to typical plasticizer. The findings are useful for producing designed biochars from different biomass wastes for plasticizer pollution control.     

Revealing the GHG reduction potential of emerging biomass-based CO2 utilization with an iron cycle system

● Greenhouse gas mitigation by biomass-based CO₂ utilization with a Fe cycle system. ● The system including hydrothermal CO₂ reduction with Fe and Fe recovery by biomass. ● The reduction potential quantified by experiments, simulations, and an ex-ante LCA. ● The greatest GHG reduction potential is −34.03 kg CO₂-eq/kg absorbed CO₂. ● Ex-ante LCA supports process optimization to maximize GHG reduction potential. CO₂ utilization becomes a promising solution for reducing anthropogenic greenhouse gas (GHG) emissions. Biomass-based CO₂ utilization (BCU) even has the potential to generate negative emissions, but the corresponding quantitative evaluation is limited. Herein, the biomass-based CO₂ utilization with an iron cycle (BCU-Fe) system, which converts CO₂ into formate by Fe under hydrothermal conditions and recovers Fe with biomass-derived glycerin, was investigated. The GHG reduction potential under various process designs was quantified by a multidisciplinary method, including experiments, simulations, and an ex-ante life-cycle assessment. The results reveal that the BCU-Fe system could bring considerable GHG emission reduction. Significantly, the lowest value is −34.03 kg CO₂-eq/kg absorbed CO₂ (−2.44 kg CO₂-eq/kg circulated Fe) with the optimal yield of formate (66%) and Fe (80%). The proposed ex-ante evaluation approach not only reveals the benefits of mitigating climate change by applying the BCU-Fe system, but also serves as a generic tool to guide the industrialization of emerging carbon-neutral technologies.     

Unveiling the interaction mechanisms of key functional microorganisms in the partial denitrification-anammox process induced by COD

● The availability of PD-anammox was investigated with higher NO₃^––N concentration. ● NO₃^––N concentration affects NO₃^––N accumulation during denitrification. ● COD concentration is determinant for N removal pathways in PD-anammox process. ● The synergy/competition mechanisms between denitrifiers and anammox was explored. Partial denitrification-anammox (PD-anammox) is an innovative process to remove nitrate (NO₃^––N) and ammonia (NH₄⁺–N) simultaneously from wastewater. Stable operation of the PD-anammox process relies on the synergy and competition between anammox bacteria and denitrifiers. However, the mechanism of metabolic between the functional bacteria in the PD-anammox system remains unclear, especially in the treatment of high-strength wastewater. The kinetics of nitrite (NO₂^––N) accumulation during denitrification was investigated using the Michaelis-Menten equation, and it was found that low concentrations of NO₃^––N had a more significant effect on the accumulation of NO₂^––N during denitrification. Organic matter was a key factor to regulate the synergy of anammox and denitrification, and altered the nitrogen removal pathways. The competition for NO₂^––N caused by high COD concentration was a crucial factor that affecting the system stability. Illumina sequencing techniques demonstrated that excess organic matter promoted the relative abundance of the Denitratesoma genus and the nitrite reductase gene nirS, causing the denitrifying bacteria Denitratisoma to compete with Cadidatus Kuenenia for NO₂^––N, thereby affecting the stability of the system. Synergistic carbon and nitrogen removal between partial denitrifiers and anammox bacteria can be effectively achieved by controlling the COD and COD/NO₃^––N.     

Efficient production of hydrogen peroxide in microbial reverse-electrodialysis cells coupled with thermolytic solutions

● Appreciable H₂O₂ production rate was achieved in MRCs utilizing NH₄HCO₃ solutions. ● Carbon black outperformed activated carbon as the catalyst for H₂O₂ production. ● The optimum carbon black loading for H₂O₂ production on air-cathode was 10 mg/cm². ● The optimum number of cell pairs was determined to be three. ● A maximum power density of 980 mW/m² was produced by MRCs with 5 cell pairs. H₂O₂ was produced at an appreciable rate in microbial reverse-electrodialysis cells (MRCs) coupled with thermolytic solutions, which can simultaneously capture waste heat as electrical energy. To determine the optimal cathode and membrane stack configurations for H₂O₂ production, different catalysts, catalyst loadings and numbers of membrane cell pairs were tested. Carbon black (CB) outperformed activated carbon (AC) for H₂O₂ production, although AC showed higher catalytic activity for oxygen reduction. The optimum CB loading was 10 mg/cm² in terms of both the H₂O₂ production rate and power production. The optimum number of cell pairs was determined to be three based on a tradeoff between H₂O₂ production and capital costs. A H₂O₂ production rate as high as 0.99 ± 0.10 mmol/(L·h) was achieved with 10 mg/cm² CB loading and 3 cell pairs, where the H₂O₂ recovery efficiency was 52 ± 2% and the maximum power density was 780 ± 37 mW/m². Increasing the number of cell pairs to five resulted in an increase in maximum power density (980 ± 21 mW/m²) but showed limited effects on H₂O₂ production. These results indicated that MRCs can be an efficient method for sustainable H₂O₂ production.     

Porous silica synthesis out of coal fly ash with no residue generation and complete silicon separation

● Both amorphous and crystalline silicon are completely separated from coal fly ash. ● Porous silica is synthesized out of coal fly ash. ● No residues is produced during the whole synthesis process. ● The one-step method to synthesize silica don’t need long-time reaction and aging. Ordered mesoporous silica materials exhibit enormous potential in industrial production. Since coal fly ash (CFA) is abundant in Si, it has become a green and promising way to utilize CFA by synthesizing porous silica materials. However, the stable crystalline structure of CFA limits the extraction of Si, and the residue is generated during the process of extracting Si. In this work, we proposed a no-residue method to synthesize ordered mesoporous silica out of CFA. Sodium carbonate (Na₂CO₃) was used to reconstruct the crystals of the CFA, and the calcined mixture then directly reacted with the precipitators. This method combined the process of Si extraction and porous material synthesis. In this method, no residue was generated and the silicon in both amorphous and crystalline phases of CFA was fully utilized. By this method, the extraction efficiency of Si was increased from 31.75% to nearly 100%. The as-synthesized mesoporous silica had a highly-ordered pore structure with a space group of la-3d, a surface area of 663.87 m²/g, a pore volume of 0.41 cm³/g, and an average pore diameter of 2.73 nm. The mechanism of crystalline transformation and material structure formation were systematically studied. This method provides a new idea to dispose of CFA and synthesize porous silica materials.