Changes to the TEF schemes can have significant impacts on regulation and management of PCDD/F and PCB

The changes recommended by the World Health Organisation (WHO) to the toxic equivalency factors (TEFs) for polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) and the recommendation to extend both the TEF scheme and the tolerable daily intake (TDI) to include "dioxin-like" PCB congeners have significant implications for regulators who have relied heavily on the International TEF (I-TEF) scheme in setting and monitoring limits and exposure to these compounds. This paper examines example data sets of sources, environmental concentrations, food and exposure to indicate likely changes in calculated toxic equivalent (TEQ) due to the recommended changes to TEFs. Many published data sets available do not provide congener specific data for PCDD/F which limits the ability to recalculate TEQs. There are even fewer congener specific data published to enable calculation of TEQs for the dioxin-like PCBs. In general TEQs calculated using the WHO scheme for emissions to air were found to show small increases (in the order of 1-10%) in comparison to the I-TEQ (for PCDD/F), some sludge samples showed substantial decreases (up to 70%). Levels in food and calculations of exposure showed that the change to TEFs for PCDD/F increased calculated exposure by 10-20% while the change to PCB TEFs decreased calculated TEQ attributable to PCB by 0-10%. The effects of including PCB in the overall TEQ and the changes to TEFs for PCDD/F substantially increase calculated TEQ exposure. Congener specific data should be presented to allow calculation of desired TEQ and the impact of the changes on emission limits, regulations on sludge use and environmental quality standards should all be carefully considered. The absence of data on emissions of dioxin-like PCB means that it is not possible to estimate with any certainty the impact on overall TEQ emissions of including the nominated PCB. Given the potential for confusion with the proliferation of TEFs and the extension to include both PCDD/F and PCB in the calculation of TEQs it is important that great care is taken to clearly express which compounds are included and which TEF scheme has been applied in each case.     

Evaluation of the European population intake fractions for European and Finnish anthropogenic primary fine particulate matter emissions

The intake fraction (iF) has been defined as the integrated incremental intake of a pollutant released from a source category or region summed over all exposed individuals. In this study we evaluated the iFs in the population of Europe for emissions of anthropogenic primary fine particulate matter (PM_2.5) from sources in Europe, with a more detailed analysis of the iF from Finnish sources. Parameters for calculating the iFs include the emission strengths, the predicted atmospheric concentrations, European population data, and the average breathing rate per person. Emissions for the whole of Europe and Finland were based on the inventories of the European Monitoring and Evaluation Programme (EMEP) and the Finnish Regional Emission Scenario (FRES) model, respectively. The atmospheric dispersion of primary PM_2.5 was computed using the regional-scale dispersion model SILAM. The iFs from Finnish sources were also computed separately for six emission source categories. The iFs corresponding to the primary PM_2.5 emissions from the European countries for the whole population of Europe were generally highest for the densely populated Western European countries, second highest for the Eastern and Southern European countries, and lowest for the Northern European and Baltic countries. For the entire European population, the iF values varied from the lowest value of 0.31 per million for emissions from Cyprus, to the highest value of 4.42 per million for emissions from Belgium. These results depend on the regional distribution of the population and the prevailing long-term meteorological conditions. Regarding Finnish primary PM_2.5 emissions, the iF was highest for traffic emissions (0.68 per million) and lowest for major power plant emissions (0.50 per million). The results provide new information that can be used to find the most cost-efficient emission abatement strategies and policies.     

Intake fraction distributions for benzene from vehicles in the Helsinki metropolitan area

The intake fraction (iF) gives a measure of the portion of a source's emissions that is inhaled by an exposed population over a defined period of time. This study examines spatial and population-based iF distributions of a known human carcinogen, benzene, from a ubiquitous urban source, local vehicular traffic, in the Helsinki Metropolitan Area using three computational methods. The first method uses the EXPAND model (EXPosure to Air pollution, especially to Nitrogen Dioxide and particulate matter), which incorporates spatial and temporal information on population activity patterns as well as urban-scale and street canyon dispersion models to predict spatial population exposure distributions. The second method uses data from the personal monitoring study EXPOLIS (Air Pollution Exposure Distributions of Adult Urban Populations in Europe) to estimate the intake fractions for individuals in the study. The third method, a one-compartment box model provides estimates within an order-of-magnitude or better for non-reactive agents in an urban area. Population intake fractions are higher using the personal monitoring data method (median iF 30 per million, mean iF 39 per million) compared with the spatial model (annual mean iF 10 per million) and the box model (median iF 4 per million, mean iF 7 per million). In particular, this study presents detailed intake fraction distributions on several different levels (spatial, individual, and generic) for the same urban area.     

Trends of PCDD/F and PCB concentrations and depositions in ambient air in Northwestern Germany

Time series of polychlorinated dioxins and furans (PCDD/F) and polychlorinated biphenyls (PCB) in ambient air of a large conurbation in North-Western Germany are presented and analyzed. The trend of PCDD/F concentrations, starting from as early as 1988, shows a pronounced decrease by at least one order of magnitude, demonstrating that the emission reductions were effective. The PCDD/F depositions also have decreased by a factor of 5 since 1992. However, both trends have leveled out since 2005. Time series of PCB concentrations and depositions starting in 1994 show only slight decreases for the concentrations and almost no decrease for the depositions. From the decay rates following first order kinetics, half-lives in the order of 5-15 years for the PCDD/F and 15-31 years for the sum of the six indicator PCB could be calculated, which are much longer than the half-lives estimated from their reactivity towards the OH radical. Apparently, small fresh emissions (PCDD/F), considerable secondary emissions and evaporation from contaminated soils slow down their decay in the atmosphere of big conurbations. Analyzing the decay rates of individual PCB congeners shows that the lower chlorinated and more volatile ones are removed faster than the higher chlorinated congeners, probably via gas phase reactions with the OH radical. It can be concluded from the present study that the input of PCDD/F and PCB into the food chain via the air path will continue for another one or two decades in big conurbations.     

Determination of tissue-blood partition coefficients for a physiological model for humans, and estimation of dioxin concentration in tissues

The tissue-blood partition coefficients for a physiologically based pharmacokinetic (PBPK) model were determined, and the concentrations of 17 congeners of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in tissues in Japanese people were estimated using the model. According to the PBPK model established by Lawrence and Gobas [Chemosphere 35 (1997) 427-452], we assumed a steady-state fugacity model for Japanese people in general, and set the route of PCDD/Fs exposure only from food intake. The required partition coefficients for liver, kidney, adipose, muscle, skin, bile, gut and viscera (richly perfused tissue) were calculated using available autopsy data from eight Japanese men and women who were not accidentally exposed to PCDD/Fs. For validation of the partition coefficients, estimated PCDD/F concentrations in liver, kidney, fat, blood and muscle using the model were compared to other two sets of measured concentration data in Japanese tissues. Good agreement was obtained between estimated data and measured data, and most of the measured data were within the simulated concentration range in liver, kidney, blood and muscle. From these results, our model and calculated partition coefficients seem applicable for the estimation of congener-specific concentrations in human tissues.     

Modeling the atmospheric transport and deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans in North America

The atmospheric fate of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) was simulated for the year 2000 in North America using a SMOKE/CMAQ-based chemical transport model that was modified for this purpose. The 1999 USEPA emission inventories of PCDD/Fs and criteria pollutants were used. The 1995 Canadian emission inventory of criteria pollutants and the 1995 Canadian area source emissions for PCDD/Fs were used with the 2000 Canadian point source emissions. Modifications to CMAQ involved coupling it with dual organic matter (OM) absorption and black carbon (BC) adsorption models to calculate PCDD/F gas–particle partitioning. The model satisfactorily reproduced the particle bound fractions at all rural sites for which there were measured data and across the whole domain, the modeled vs. measured differences in particle bound fractions were less than 20% for nearly all congeners. The model predicted ambient air PCDD/F concentrations were also consistent with measurements. Simulated deposition fluxes were within 58% of direct measurements. PCDD/F atmospheric depositions to each of the Great Lakes were estimated for the year 2000. The results indicate that approximately 76% of the total deposition of PCDD/Fs to the Great Lakes (in W-TEQ, or toxic equivalent units as defined by the World Health Organization) is attributed to PCDD/Fs absorbed into OM in aerosol. For all of the lakes, more than 92% of all deposition is particle phase wet deposition and only 5–8% is particle phase dry deposition. Wet deposition from the gas phase is negligible. Of the 17 toxic PCDD/F congeners, the Cl_4–5DD/F compounds contribute approximately 70% to the total atmospheric deposition to the Great Lakes. The seasonal changes in the PCDD/F deposition flux track variations in ambient temperature.     

Seasonal variation of PCDD/Fs in the metropolis of Istanbul,Turkey

Atmospheric concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) compounds were investigated at three different regions of Istanbul which reflect urban, urban/industrial, and sub-urban characteristics. Air samples were collected simultaneously for both gaseous and particulate phases using high volume samplers on monthly time intervals from May 2011 to October 2012. The highest concentrations (3,056 fg/m³ and 156 fg I-TEQ/m³) were observed at the sampling site that reflects traffic, residential, and industrial emission source characteristics, while the lowest concentrations (829 fg/m³ and 38 fg I-TEQ/m³) were observed at the sampling point which is far away from centrum and reflects sub-urban characteristics. Concentrations of PCDD congeners were, in general, found to be higher than PCDF congeners, and OCDD, 1,2,3,4,6,7,8-HpCDD/F, and OCDF congeners were recorded to be the most abundant congeners. Winter season concentrations were also found to be higher especially in particulate phase. As a result, combustion processes such as motor vehicles and residential heating equipment were thought to be the principal sources of emissions of PCDD/F compounds when both congener profiles and seasonal variations are considered. Basic statistical evaluation of the data resembled high degree of inverse correlations between PCDD/F concentrations and UV and solar radiation.     

Dioxin and dioxin-like PCB exposure of non-breastfed Dutch infants

The exposure of humans to PCDD/Fs (polychlorinated dibenzo-p-dioxins and dibenzofurans) and dioxin-like PCBs (dl-PCBs, i.e. polychlorinated non-ortho and mono-ortho biphenyls) occurs predominantly via the intake of food. Young children have a relatively high intake of these substances, due to their high food consumption per kilogram body weight. As the exposure of non-breastfed infants to these compounds has not been assessed before in The Netherlands, we studied the dietary intake of 17 PCDD/Fs and 11 dioxin-like PCBs in 188 Dutch non-breastfed infants between 4 and 13 months. The food intake of the infants was assessed by a 2-d food record. From these data PCDD/F and dioxin-like PCB intake was calculated using PCDD/F and dioxin-like PCB concentrations of food products sampled in 1998/1999 in The Netherlands. The long-term PCDD/F and dioxin-like PCB exposure of the infants was calculated using the statistical exposure model (STEM). For infants of 5 months the chronic exposure to PCDD/F and dioxin-like PCB was 1.1pg WHO-TEQ (toxic equivalents) per kilogram body weight (bw) per day (95th percentile: 1.7pg WHO-TEQ/kg bwxd), which mainly originated from infant formula and vegetables and increased to 2.3pg WHO-TEQ/kg bwxd (95th percentile 3.7pg WHO-TEQ/kg bwxd) for infants just over 1 year old eating the same food as their parents. The percentage of formula-fed infants with an exposure exceeding the TDI of 2pg WHO-TEQ/kg bwxd was 5% at 5 months, 49% at 9 months and 64% at 12 months.     

A congener-specific PCDD/F emissions inventory for the UK: do current estimates account for the measured atmospheric burden?

Considerable effort has been expended in the UK and elsewhere to quantify and rank PCDD/F primary sources and emissions to the environment, principally the atmosphere, so that cost-effective source reduction measures can be taken. Here, we predict a congener-specific emissions inventory for primary and secondary nondioxin-regulated sources to the UK atmosphere, estimated to have ranged from 3 to 22 kg in 1996. The inventory profile is dominated by OCDD (approximately 30-40%), 1,2,3,4,6,7,8-HpCDD (approximately 15-19%) and 1,2,3,4,6,7,8-HpCDF (approximately 14-19%). Congeners 2,3,4,7,8-PeCDF and 1,2,3,7,8-PeCDD dominate the sigmaTEQ composition. Mass balance modelling suggests that the predicted congener pattern in UK air (based on the emission inventory) is similar to observed measurements, with absolute concentrations being estimated within a factor of 2 for most congeners. Calculations taking into account atmospheric weathering processes and long range (advective) transport suggest that PCDD/F sources to ambient air are primarily ongoing and that atmospheric mixing will mask individual emission source profiles/identities. This supports measured evidence for the consistency of PCDD/F air profiles observed around the UK throughout the year.     

PCDD/PCDF congener profiles in soil and herbage samples collected in the vicinity of a municipal waste incinerator before and after pronounced reductions of PCDD/PCDF emissions from the facility

Congener profiles are the fractional distribution of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) congeners in an environmental release, or in an environmental or biological sample. In 1999, an adaptation to the EU legislation on pollutant emissions from the stack was carried out in an old municipal solid waste incinerator (MSWI) from Montcada (Barcelona, Spain). The main goal of the present study was to determine if the environmental PCDD/F levels in the area under direct influence of the facility were mainly due to PCDD/F emissions from the plant. For this purpose, soil and herbage samples were collected near the MSWI before (1998) and after (2000) the technical improvements were performed. PCDD/F congener profiles were determined and compared with those from samples collected in a suburban area of Constantí (Tarragona, Spain) outside of direct emissions from any MSWI. The results of the present study suggest that the MSWI here assessed is not the main responsible for the environmental PCDD/F concentrations in the area under evaluation. Other PCDD/F emission sources in the same area seem also to have a notable impact on the atmospheric levels of these pollutants.     

Improvements to the UK PCDD/F and PCB atmospheric emission inventory following an emissions measurement programme

PCDD/F data are presented from 75 samples of primary emissions sampled between 1995-97 as part of the compliance monitoring survey undertaken by the UK Environment Agency. Municipal solid waste (MSW), chemical waste and clinical waste incinerators, cement kilns, sinter plants and sewage sludge incinerators were the source categories monitored and reported here. Based on this monitoring programme, the previous national UK emission estimates by Eduljee and Dyke (1) of 560-1100 g I-TEQ a(-1) for 1993 have been revised downwards to 220-660 g I-TEQ a(-1). Despite source reduction measures, MSW incinerators remain a significant source of PCDD/Fs to the atmosphere, contributing between 30-50% of the EPCDD/F I-TEQ emission, rather than the approximately 80% they were estimated to contribute in 1993. 2,3,7,8-substituted PCDD/F congener profile data are presented for some of the source categories and generally support the view that differences in the mixtures ('fingerprints') of PCDD/Fs emitted from different sources are observed. New data on the dioxin-like PCB emissions are presented for cement kilns and sinter plants. These show that TEQ-rated PCBs can make an important contribution to the I-TEQ emitted from certain combustion sources. High concentrations of a full range of PCB congeners/homologues have been measured in the atmosphere close to sintering strands, although the precise source of PCBs from this process remains unclear.     

Congener-specific intake fractions for PCDDs/DFs and Co-PCBs: modeling and validation

Intake fractions (iFs) for emissions to air, water, and soil for 17 PCDDs/DFs and 12 Co-PCBs were calculated with a level III multimedia model and a food-chain exposure model in succession. The two integrated models were tested by comparing the predicted and measured concentrations in the environment and by comparing intakes through food. Measurement-based iFs were also calculated and compared with the model-based iFs. The air concentrations predicted by the fate model were close to the median of the observed concentrations, whereas the predicted soil and water concentrations were one-third to one-tenth the observed concentrations. This difference was large in case of PCDDs and Co-PCBs, which was explained by the past pollution such as commercial PCB products and PCDD impurities in chloronitrofen (CNP) and pentachlorophenol (PCP). For fish, the predicted and observed exposures agreed well each other. For meat and milk, the predicted exposures were about 10 times the observed exposures for PCDDs/DFs, whereas the predicted and observed values agreed well for Co-PCBs. When the model was modified to consider feeding of fish meal to livestock and geographic bias in feed-grass production, the predicted congener profile was comparable to the measured profile. The comparison also suggested that chickens should be modeled separately from other terrestrial livestock. The model-based iFs for air emission of OCDD and 2378-TCDD were 0.001% and 0.1%, respectively. The iFs of most Co-PCBs were higher than those of PCDDs/DFs. These iF differences suggest the importance of the fate factor in assessing emissions of the 29 congeners.     

Post-combustion syntheses of PCDD/F and PBDD/F from halogen-rich fuel is suppressed by a pebble heater technology

GOAL, SCOPE AND BACKGROUND: Changes in German and European legislation shifted processing of polymer-rich shredding residues (SR) from landfill to thermal treatment. However, when waste of electric and electronic equipment (WEEE) is the source of SR, thermal treatment is complicated by halogens as well as the presence of polybrominated dioxins and furans (PBDD/F) and brominated flame retardants (BFR). Hence, WEEE requires high temperature incineration with sufficient residence times. Post-combustion synthesis of polyhalogenated dioxins and furans (PXDD/F) is dominant in the temperature range between 250-450 degrees C. Thus, a very rapid gas cooling from 450 degrees to 250 degrees C is important for proper raw gas treatment. The pebble heater technology developed by ATZ Entwicklungszentrum (Sulzbach-Rosenberg, Germany) might serve as an alternative to the state-of-the-art quench cooling. It is based on the application of a pebble bed of natural bulk material, which the exhaust gases flows through radially. It provides an excellent heat transfer and a temperature gradient in the range of 1,500-2,000 K/m. The paper presents data of a pilot application of the pebble heater technology for the treatment of raw gas derived from the incineration of polymeric materials from WEEE. METHODS: A liquid fuel was chosen in order to minimise technical modifications of the plant. It was analysed for halogens by x-ray fluorescence, for brominated flame retardants by HPLC-UV/MS and for PXDD/F by GC-HRMS. Combustion gases were rapidly cooled down to temperatures below 200 degrees C and emissions of PBDD/F and PCDD/ F were estimated without further off-gas treatment. PBDD/F emissions were computed as PCDD/F toxicity equivalents applying two different calculation approaches. RESULTS AND DISCUSSION: PCDD/F emissions accounted for 0.04 ng I-TEQ/Nm3 and are in compliance with European emission limits. Calculated PBDD/F toxicity equivalents exceeded the emission limit of 0.1 ng I-TEQ/Nm3 by factors of 75 and 208 depending on the calculation approach. A mass balance of PBDD/F and PCDD/F congeners revealed an efficient elimination of more than 95% in most cases. Lower reduction rates (76% for 2,3,7,8-TeBDF and 82% for 1,2,3,7,8-PeBDF) were attributed to incomplete combustion. An intended recovery of halogens by one-stage scrubbing downstream of the pebble heater was ineffective, recovering 28% of the applied chlorine and 9% of the bromine, only. CONCLUSIONS: Our pilot incineration test indicates that the pebble heater technology can effectively suppress a post-combustion synthesis of PCDD/F and PBDD/F, resulting in low PCDD/F emission levels without further off-gas treatment. The presented data state that WEEE is sensible to incomplete combustion, which will lead to increased PBDD/F emissions without increasing PCDD/F emission limits. This finding is especially relevant for small and low-technical incineration appliances, which have been reported to treat WEEE in developing countries and are considered to serve as a significant source of PXDD/F these days. RECOMMENDATIONS AND PERSPECTIVES: Monitoring of PCDD/F emissions only might considerably underestimate the total emission of dioxins and dioxin-like compounds. It is therefore an ineffective means for assessing resulting health risks, at least for those waste treatment plants which are considered to handle the increasing amounts of PBDD/ F-containing polymers from WEEE in future. Consequently, it is recommended to initiate a screening programme for PXDD/F emissions in large scale incineration facilities which are capable of treating WEEE shredder residues.     

Influence of start-up on PCDD/F emission of incinerators

This study aims to evaluate the influence of start-up on polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) concentration in the stack flue gas of incinerators and its contributing PCDD/F emission. The PCDD/F emission of the first sample among three consecutive stack flue gas samples of five intermittent incinerators, which sampled at a stable combustion condition after start-up, is 2-3 times higher than the mean of the others. For verifying the PCDD/F characteristics of incinerators during start-up, one continuous MSWI was investigated for two years. The elevated PCDD/F emissions of the MSWI during start-up could reach 96.9 ng I-TEQN m(-3) and still maintained a high PCDD/F emission (40 times higher than the Taiwan emission limit) even 18 h after the injection of activated carbon, indicating the memory effect. Taking the MSWI for example, which consists of four incinerators, the estimated annual PCDD/F emission from normal operational conditions was 0.112 g I-TEQ. However, one start-up procedure can generate approximately 60% of the PCDD/F emissions for one whole year of normal operations. And the PCDD/F emission, which is the result of the start-ups of four incinerators, was at least two times larger than that of a whole year's normal operations, without consideration for the PCDD/F emission contributed by the long lasting memory effect.     

PCDD/F and "Dioxin-like" PCB emissions from iron ore sintering plants in the UK

Investigations have been carried out at the three Corus UK sinter plants over the period 2002-2004 to characterise the emissions of both 2,3,7,8-PCDD/Fs and WHO-12 PCBs, to estimate annual mass releases of these organic micro-pollutants using the I-TEF and WHO-TEF schemes, and to investigate the formation of PCBs in the iron ore sintering process. Results showed that the sintering of iron ore produces a characteristic WHO-12 PCB and PCDD/F congener pattern that is substantially the same for all UK sinter plants. With regard to WHO-12 PCBs, the most abundant congeners were typically PCBs 118 (6-9 ngNm(-3)), 105 (2-4 ngNm(-3)) and 77 (2-3 ngNm(-3)). All other WHO-12 PCBs were also detected at concentrations around 1 ngNm(-3). All sinter plants investigated exhibited very similar TEQ concentrations. WHO-12 PCB emissions were in the range 0.042-0.111 ngWHO-TEQNm(-3), whereas PCDD/F emissions ranged from 0.39 to 1.62 ngWHO-TEQNm(-3). PCDF congeners were the main contributors to the overall TEQ in sintering emissions (ca. 85%). Amongst WHO-12 PCBs, PCB 126 was the only noteworthy contributor to total TEQ (ca. 5-7%), a similar contribution to that from PCDDs. Based on the measurements that Corus UK has undertaken at these three sinter plants, annual mass releases of WHO-12 PCBs and PCDD/Fs have been calculated. For UK sinter plants, a total mass release of 29.5 g WHO-TEQ per annum [WHO-12 PCBs+PCDD/Fs] has been estimated, representing 9% of the total PCDD/F emissions to the UK atmosphere. Measurements were also carried out at a UK sinter plant to determine the windleg emission profile of WHO-12 PCBs. Results showed that WHO-12 PCBs were formed in the same regions of the sinter strand as 2,3,7,8-PCDD/Fs, indicating that there was a strong correlation between the formation of WHO-12 PCBs and PCDD/Fs in the iron ore sintering process.     

An incinerator air quality impact assessment for metals, PAH, dioxins and furans by using the MM5-CMAQ-EMIMO atmospheric modelling system: Spain case study

In this paper, we show the implementation of a modified version of MM5-CMAQ for carrying out an air quality impact analysis for installing an incinerator in the Basque Country model domain (Spain). The modified CMAQ model (EPA USA, 2004) includes Poly-Chlorinated Dibenzop-Dioxins and Dibenzo-Furans (dioxins and furans). This model represents their congeners as divided between gaseous and aerosol forms that exchange mass based on theoretical coefficients for gas to particle portioning. The emission model EMIMO – developed by UPM – has been adapted to incorporate the three metals and the benzo(a)pyrene according to the EMEP annual emission inventory. In addition, the PCDD/F EMEP emission inventory has been incorporated into the EMIMO model to produce proper 1 hr and 1 km × 1 km emission PCDD/F estimation. The emissions of the projected incinerator are incorporated by using the chimney technical parameters and the limit emission values (worst-case scenario) prescribed in the Directive/2000/76/CE.     

Congener specific transfer of PCDD/Fs from air to cows' milk: an evaluation of current modelling approaches

Three different approaches have been used to model the transfer of individual PCDD/F congeners from the air to cows' milk. These are: (1) an 'Equilibrium Partitioning' approach, (2) a 'Deposition Velocity' approach and (3) a 'Scavenging' approach. Air-leaf transfers and livestock feed-milk transfers, the two most critical components of the food chain exposure model, are discussed. A representative database for measured PCDD/Fs in UK air, herbage and milk is presented and the performance of each predicted model concentration against this measured dataset is assessed. Weaknesses and uncertainties associated with modelling the complex transfer processes involved are highlighted.     

Bioavailability of PCDD/F from contaminated soil in young Goettingen minipigs

For the general population the intake of food of animal origin is the main route of human exposure to polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F). Besides this the ingestion of contaminated soil might be an important exposure path for small children. For risk assessment the knowledge of the bioavailable fraction of soil bound contaminants is important. In a balance study with young Goettingen minipigs the oral bioavailability of PCDD/F from contaminated soil was estimated by determination of the retention of PCDD/F from soil in different organs and tissues. Relative bioavailability was estimated by comparing the retention from soil to the retention of PCDD/F in organs and tissues after oral administration of a PCDD/F mixture extracted from the same soil by solvent. The soil had a PCDD/F-contamination of 5.3 microg I-TEq/kg and originated from a former arable land that had been treated with sludge from the port of Hamburg some years ago. Two groups of each four animals were exposed daily for 28 days via their diet either to 0.5 g soil per kg body weight and day (2.63 ng I-TEq/(kg(bw).d)) or to a daily dose of 1.58 ng I-TEq/(kg(bw).d) given to the diet by solvent. Five unexposed animals were used as a control group. Liver, adipose tissue, muscle, brain and blood were analyzed for their PCDD/F content. Accumulation of PCDD/F from soil or solvent in comparison to control animals was only observed for congeners with 2378-chlorosubstitution and predominantly took place in the liver. Bioavailability of 2378-chlorosubstituted congeners was in the range of 0.64%-21.9% (mean: 10.1%) from soil and 2.8%-59.8% (mean: 31.5%) when administered by solvent. The soil matrix reduced the bioavailability by about 70%. Expressed as I-TEq only 13.8% of the PCDD/F contamination were bioavailable from soil. The relative bioavailability of 2378-chlorosubstituted congeners from soil in relation to administration by solvent was in the range of 2%-42.2% (mean: 28.4%). When not considering the bioavailability, the risk by oral uptake of PCDD/F contaminated soil might be overestimated.     

PCBs and PCDD/Fs in lake sediments of Grosser Arbersee, Bavarian Forest, South Germany

Despite their environmental importance, there are still relatively few historical studies of the environmental occurrence of polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), especially in middle Europe. Trends in PCBs and PCDD/Fs were, therefore, assessed in lake sediments of the Grosser Arbersee over the past 130 years (1860-1990). Ballschmiter-PCB concentrations (congeners # 28, 52, 101, 138, 153, 180) increased between 1946 and 1972 from 4.2 to 32.0 microg kg(-1) dry wt, but have since decreased to 25.6 microg kg(-1) dry wt. High chlorinated PCB congeners reached their maxima earlier (1968-1972) than low chlorinated congeners (1985-1991). These trends were consistent with patterns expected from the production and use of PCBs and their precursors. PCDD/F concentrations increased between 1950 from 0.6 microg kg(-1) dry wt to 2.3 microg kg(-1) dry wt in 1977, falling to 1.7 microg kg(-1) dry wt by 1993. PCDF concentrations exceeded those of PCDD until 1968, but afterwards PCDDs (especially OCDD) were predominant. These patterns suggest that domestic heating and waste combustion were the most likely sources, but pollution from local industries, such as metal smelting and glass production, might also have been involved. The data provide a valuable case study from central Europe which confirms the overall declining trends of PCB and PCDD/F contamination shown elsewhere.     

Emissions of PCDD/Fs, PCBs, and PAHs from legacy on-road heavy-duty diesel engines

Exhaust emissions of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxin/furan (PCDD/F) congeners, tetra-octa PCDD/F homologues, 12 WHO 2005 polychlorinated biphenyl (PCB) congeners, mono-nona chlorinated biphenyl homologues, and 19 polycyclic aromatic hydrocarbons (PAHs) from three legacy diesel engines were investigated. The three engines tested were a 1985 model year GM 6.2 J-series engine, a 1987 model year Detroit Diesel Corporation 6V92 engine, and a 1993 model year Cummins L10 engine. Results were compared to United States’ mobile source inventory for on-road diesel engines, as well as historic and modern diesel engine emission values. The test fuel contained chlorine at 9.8 ppm which is 1.5 orders of magnitude above what is found in current diesel fuel and 3900 ppm sulfur to simulate fuels that would have been available when these engines were produced. Results indicate PCDD/F emissions of 13.1, 7.1, and 13.6 pg International Toxic Equivalency (I-TEQ) L⁻¹ fuel consumed for the three engines respectively, where non-detects are equal to zero. This compares with a United States’ mobile source on-road diesel engine inventory value of 946 pg I-TEQ L⁻¹ fuel consumed and 1.28 pg I-TEQ L⁻¹ fuel consumed for modern engines equipped with a catalyzed diesel particle filter and urea selective catalytic reduction. PCB emissions are 2 orders of magnitude greater than modern diesel engines. PAH results are representative of engines from this era based on historical values and are 3-4 orders of magnitude greater than modern diesel engines.