Optimization of esterification of fatty acid rubber seed oil for methyl ester synthesis in a plug flow reactor

To date, non-food vegetable oil has been considered as the primary source for biodiesel production. Rubber seed oil has high acid value (34 mgKOH/g) and can be used for biodiesel synthesis. The purpose of this study was to investigate esterification of fatty acid, which derived from rubber seed oil, in a plug flow reactor system at high temperature and low methanol consumption. Response surface methodology was applied for design experiment and optimization of esterification reaction. Temperature, methanol consumption, and sulfuric acid were chosen as variables to examine their influence in a conversion to methyl ester. At 140°C, at 5:1 methanol to fatty acid ratio (by mole), H₂SO₄ 1.5 (%v/w), and space time 20 min, the conversion to methyl ester attained 98.2%. Fourier transform infrared spectroscopy (FTIR) and gas chromatography-Mass spectrometry (GC-MS) were used for analysis and to confirm the formation of methyl ester. Methyl ester was characterized for biodiesel fuel properties in accordance to ASTM standard.     

Application of TiO2 nanoparticles for eco-friendly biodiesel production from waste olive oil

An environmentally benign, simple, and efficient process has been developed for biodiesel production from waste olive oil in the presence of a catalytic amount of TiO₂ nanoparticles at 120°C with a conversion of 91.2% within 4 h. The present method affords nontoxic and noncorrosive medium, high yield of biodiesel, clean reaction, and simple experimental and isolation procedures. The catalyst can be recycled by simple filtration and reused without any significant reduction in its activity.     

Prospect of castor oil biodiesel in Bangladesh: Process development and optimization study

In this study, castor oil (CO) has been investigated as a potential source for biodiesel production in Bangladesh. Castor oil has been extracted from the seeds by mechanical press and the Soxhlet extraction method. Maximum oil content of 55.7% has been found by the Soxhlet extraction method. The physicochemical properties such as free fatty acid (FFA) content, kinematic viscosity, saponification value, and density of the oil have been measured by different standard methods. The FFA content and viscosity have been found considerably higher such as 33.5% and 253 mm²/s, respectively. Biodiesel has been prepared using a three-step method comprising of saponification of oil followed by acidification of the soap and esterification of FFA. The overall yield of FFA from CO is found to be around 89.2%. The final step is esterification that produces fatty acid methyl ester (FAME) and a maximum 97.4% conversion of FFA to biodiesel has been observed. The effect of the oil to methanol molar ratio, catalyst concentration, reaction temperature, and time has been investigated for esterification reaction and optimized using the response surface methodology. ¹H NMR of crude castor oil and castor oil methyl ester (COME) was studied and analyzed that confirms the complete conversion of castor oil to biodiesel. Finally, the biodiesel, produced under optimum conditions, was characterized using the various standard method and found comparable with petro-diesel and biodiesel standard.     

Homogeneous catalysed biodiesel synthesis from Alexandrian Laurel (Calophyllum inophyllum L.) kernel oil using ortho-phosphoric acid as a pretreatment catalyst

In this study, a non-edible seed oil of Alexandrian Laurel (Calophyllum inophyllum L.) with higher free fatty acid content has been harnessed to produce biodiesel by transesterification process. The 20.2% free fatty acid (FFA) content was first reduced to 12.9% by using TOP degumming process. Ortho-phosphoric acid was used to esterify the refined kernel oil. Transesterification reaction was performed with NaOH as an alkaline catalyst and methanol as an analytical solvent. The effects of methanol to oil molar ratio (MR), catalyst concentration (CC), reaction temperature (TP), reaction time (TM), and stirrer speed (SS) on biodiesel conversion were studied to optimize the transesterification conditions using DOE- approach. The experimental study revealed that 9:1 MR, 0.8 wt.% CC, 60°C TP, 75 min TM and 1000 rpm SS were the optimal process control variables. The study indicated that CC was the most important control parameter in optimal methyl ester production. The optimal treatment combination yielded 97.14% of biodiesel. The profile of biodiesel was determined using gas chromatography-mass spectrometry. ¹H NMR spectrum of Calophyllum inophyllum methyl ester (CIME) has been reported. The properties of the biodiesel have been found within specifications of the ASTM D6751 and EN 14214 standards and hence could be considered as a suitable alternative to diesel fuel for sustainable circulation of carbon.     

Ferric-manganese doped sulphated zirconia nanoparticles catalyst for single-step biodiesel production from waste cooking oil: Characterization and optimization

Biodiesel of waste cooking oil origin is gaining attention as a replacement for current fossil fuels, as its low-priced, recycled feedstock shall prevent food source competition, which is estimated to happen with current biodiesel production processes. As a result, waste cooking oil has been claimed to be a highly potential feedstock for biodiesel production. In the present research work, Fe-Mn doped sulphated zirconia catalyst was synthesized and used in simultaneous esterification and transesterification of waste cooking oil to biodiesel synthesis. The catalyst was prepared through the impregnation method and characterized by using XRD, TPD-NH_3, FT-IR, BET, and TEM. Response surface methodology (RSM) in conjunction with the central composite design (CCD) was applied to statistically evaluate and optimize the biodiesel preparation process. It was found that the synthesis of biodiesel achieved an optimum level of 97.2% waste cooking oil methyl ester’s (WCOME’s) yield at the following reaction conditions: methanol/oil molar ratio: 10:1, catalyst concentration: 3.0 wt %, and reaction temperature: 160 °C. The extremely high WCOME’s yield of 97.2% was proved to be due to high acidity, surface area, and large pore diameter; reactants can easily diffuse into the interior pore of the catalyst and allow them to be in contact with active sites that enhance catalytic activity.     

Biodiesel production from a free fatty acid containing Karanja oil by a single-step heterogeneously catalyzed process

Karanja oil, containing 6.2% free fatty acids (FFAs), was considered for biodiesel production using a single-step solid-phase acid catalyzed process. Different types of zeolites and Amberlyst15 catalysts were tested and biodiesel was produced. Under similar conditions, the highest biodiesel yield was achieved using an Amberlyst15 catalyst, which contained 3–5% of moisture. The effects of operating parameters of the reaction such as reaction temperature, catalyst amount, and methanol-to-oil ratio were studied. An increase of methanol:oil ratio revealed a non-monotonic increase in biodiesel yields. Similar non-monotonic behavior was observed when Jatropha oil was used. Leaching and catalyst reusability were also considered. No significant effects of leaching were observed and catalyst reusability appeared to be affected by methanol interactions. The presence of a co-solvent, Tetrahydrofuran (THF), increased the biodiesel yield. Furthermore, an optimum amount of THF (THF:methanol volume ratio of 1:2) gave rise to the highest biodiesel yield. A biodiesel yield of 93% was achieved at 120 °C using a single-step process with Amberlyst15 as a catalyst, THF as a co-solvent, and a methanol:oil ratio of 30:1.     

Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Experimental evaluation of the catalytic efficiency of calcium based natural and modified catalyst for biodiesel synthesis

Transesterification of a mixture of vegetable oils with methanol using metal oxide catalysts derived from snail shell (SS) for biodiesel production was investigated. The metal oxides obtained from calcined snail shells in the temperature range of 650°–950 °C and modified by loading different potassium salts were used as a catalyst in the process. The catalysts were characterized by FT-IR, XRD, SEM-EDS, XPS and TGA. Catalytic activities of developed catalysts were also tested by Hammet indicator method and ion exchange method. The best calcination conditions were observed at 850°C for 4 hours based on biodiesel yield. The KF loaded snail shell gave highest biodiesel yield of 98 ± 1% in a batch reactor with highest basicity (15.9 mmoles/g) and basic strength measured by Hammet method. The optimized reaction conditions were: reaction temperature 65°C, reaction time 3 hours, methanol to oil molar ratio 9:1 and catalyst concentration 3wt%. Leaching and reusability tests confirm the stability of the catalyst as it encounters only 3% of leaching and small changes in catalytic activity up to five runs in terms of biodiesel yield.     

Clam shell catalyst for continuous production of biodiesel

Continuous flow transesterification of waste frying oil (WFO) with methanol for the biodiesel production was tested in a laboratory scale jacketed reactive distillation (RD) unit packed with clam shell based CaO as solid catalyst. The physiochemical properties of the clam shell catalysts were characterized by X-ray Diffraction (XRD), Brunauer–Emmett–Teller (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive Atomic X-ray Spectrometry (EDAX). The effects of the reactant flow rate, methanol-to-oil ratio, and catalyst bed height were studied to obtain the maximum methyl ester conversion. Reboiler temperature of 65°C was maintained throughout the process for product purification and the system reached the steady state at 7 hr. The experimental results revealed that the jacketed RD system packed with clam shell based CaO showed high catalytic activity for continuous production of biodiesel and a maximum methyl ester conversion of 94.41% was obtained at a reactant flow rate of 0.2 mL/min, methanol/oil ratio of 6:1, and catalyst bed height of 180 mm.     

Promotional effect of transition metal doping on the properties of KF/CaO catalyst for biodiesel synthesis

A series of heterogeneous KF/CaO catalysts modified with transition metals (lanthanum, cerium, and zirconium) were prepared via wet impregnation method and applied to the trsansesterification process of waste cooking oil (WCO) as feedstock with methanol to biodiesel production. The structure, performance of the solid catalysts was characterized by X-ray diffraction (XRD), temperature programmed desorption of CO₂ (CO₂-TPD), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS). The effect of methanol/oil molar ratio, ¹reaction time, reaction temperature, catalyst amount, and stability was investigated. The results showed that 10 wt% of lanthanum, cerium, and zirconium improved the catalytic activity of KF/CaO catalyst. The maximum catalytic activity using the lanthanum doping of 10wt% on KF/CaO catalyst was reached 98.7% under the optimal reaction condition of methanol/oil molar ratio of 12:1, reaction for 1 h at reaction temperature of 65°C, and 4% (wt/wt oil) catalyst amount. In addition, the FAME yield of KF/CaO/La catalyst remained higher than 95% after 10 cycles. The promotional effect of lanthanum doping could be attributed to the enhancement of the basicity strength of KF/CaO catalyst and block the leach of Ca²⁺ in the transesterification reaction.     

Production and characterization of biodiesel from Eriobotrya Japonica seed oil: an optimization study

Biodiesel is now-a-days recognized as a real potential alternative to petroleum-derived diesel fuel due to its number of desirable characteristics. However, its higher production cost resulting mainly due to use of costly food-grade vegetable oils as raw materials is the major barrier to its economic viability. Present work is an attempt to explore the potential of Eriobotrya japonica seed oil for the synthesis of biodiesel using alkali-catalyzed transesterification. Optimization of production parameters, namely molar ratio of alcohol to oil, amount of catalyst, reaction time and temperature, was carried out using Taguchi method. Fatty acid composition of both oil and biodiesel was determined using GC and H¹ NMR. Alcohol to oil molar ratio of 6:1, catalyst amount of 1% wt/wt, 2 h reaction time and 50 ^°C reaction temperature were found to be the optimum conditions for obtaining 94.52% biodiesel. Highest % contribution was shown by the ‘amount of catalyst’ (67.32%) followed by molar ratio of alcohol to oil (25.51%). Major fuel properties of E. japonica methyl esters produced under optimum conditions were found within the specified limits of ASTM D6751 for biodiesel, hence it may be considered a prospective substitute of petro-diesel.     

Production of chicken fat ethyl esters via optomized protocols with dry washing by silica gel

The chicken fat ethyl ester (CFEE) was developed through alkali-catalyzed transesterification with ethanol using potassium hydroxide (KOH) as a catalyst. Parameters affecting the process of transesterification such as the catalyst concentration, ethanol to oil molar ratio, reaction temperature, and reaction duration are investigated. As a result, maximum CFEEs of 90% (~96.21 ester content% w/w) was obtained under optimal conditions of 1.0 wt.% KOH, 8:1 ethanol to fat molar ratio, a reaction temperature of 70°C, and a duration of 90 min. Dry washing method using (3.0% w/w) of silica gel was used to purify the crude ethyl ester from the residual catalyst, glycerol, and other impurities. Properties of the produced ethyl esters were determined and found in accordance with specifications prescribed by the ASTM standards. Moreover, blends of CFEEs and petrodiesel were prepared and evaluated according to ASTM test methods.     

Garcinia gummi-gutta (L.) Robs.: A promising feedstock for biodiesel production

In the present study crude Garcinia gummi-gutta seed oil was evaluated as a potential feedstock for biodiesel production. Due to the high acid value (29.73 mg KOH/g) the oil was converted to biodiesel by using acid catalyzed esterification process. Further, biodiesel properties of the sample were evaluated, which fulfilled the biodiesel specifications laid by ASTM D6751, EN 14214 and IS 15607. The biodiesel possessed excellent cetane number (66.09) and a high flash point (158°C). In addition, the calorific value (41.03 MJ/kg) was very close to diesel fuel. The results suggest that the G. gummi-gutta can be an alternative source for diesel and can be used as a potential feedstock for biodiesel in India.     

Optimization of extraction of oil and biodiesel from Thespesia populnea seed oil by alkali catalyst in India

Thespesia populnea oil was new source of biodiesel. Crude Thespesia populnea oil was used as feedstock for biodiesel production by alkali-catalyzed methanolysis. The reaction in the presence of NaOH as catalyst was carried out to investigate the optimum conditions and to study the effects of variables on the reaction. A methanol to oil ratio of 6:1, sodium methoxide catalyst concentration of 1.5%, mixing intensity of 250 rpm and reaction temperature of 60°C offered the best Thespesia populnea seed oil methyl esters (biodiesel) yield (92.6%). The methyl ester content under these optimum conditions was 92.6% w/w, and all of the measured properties of the Thespesia populnea biodiesel (TPME) met the international standards ASTM D 6751-02. The results reveal that all of the reaction variables in this study had positive effects on the reaction. The results of the present study indicated that TPME could be a potential alternative to petrodiesel     

Effect of calcination temperature on the application of sodium zirconate solid base catalyst for biodiesel production from Jatropha curcas oil

Influence of catalyst calcination temperature on the catalyst characteristics and catalytic transesterification of Jatropha curcas oil for biodiesel production was studied by using sodium zirconate (Na₂ZrO₃) solid base catalyst. Na₂ZrO₃ catalysts were prepared by impregnation method followed by calcination at temperatures of 700, 800, and 900°C. The prepared catalysts were characterized by X-ray diffraction analysis, Fourier transform infrared spectroscopy, and field emission scanning electron microscopy. Important parameters influencing the catalytic activity and fatty acid methyl ester yield were investigated. It was found that the increase in calcination temperature showed marked increase in activity due to the increased porosity and presence of tetragonal zirconia. Investigation of the reusability of the catalysts showed that the catalytic activity was retained even after five cycles of reaction.     

The Evaluation of Mesoporous Materials as Catalyst in Fast Pyrolysis of Wheat Straw

In this study, wheat straw was chosen as a biomass sample and the fast pyrolysis of this sample was carried out with or without catalyst at different conditions in a well-swept fixed-bed reactor. Experiments were carried out in a well-swept tubular fixed-bed reactor with a heating rate of 300°C/min, between pyrolysis temperature ranges 300–800°C in the nitrogen atmosphere. The results indicated that a maximum oil yield of 31.9% was obtained at a pyrolysis temperature of 500°C in non-catalytic procedure. Siliceous and Al-MCM-41 materials were evaluated as potential catalysts in the pyrolysis experiments. Mesoporous materials have large pore dimensions with strong acid sites. These acidic sites catalyze some reactions in pyrolysis. The product yields and the quality of bio-oil were influenced with using MCM-41 materials. The bio-oil yield was reduced, whereas the gas yield increased with using a catalyst in the experiments. An increase in the fractions of pure phenol, alkyl phenols, alkenes+alkanes, carbonyls, aromatic, and cyclic compounds and a decrease in the fractions of methoxy phenols, acids+esters, furans, and alcohols were observed in the presence of Al-MCM-41 material. According to all results, the use of Al-MCM-41 materials as catalyst in the pyrolysis can be suggested to obtain both quality fuels and valuable chemicals.     

Nanocatalyzed biodiesel synthesis from the oily contents of Marine brown alga Dictyota dichotoma

This research article demonstrates biodiesel synthesis through the methanolysis of the oily contents (4.02 ± 0.27% w/w on dried basis) of Dictyota dichotoma collected from the coast of Hawksbay, Pakistan. The metal oxides (CaO, MgO, ZnO, and TiO₂) used as nanocatalysts were refluxed (5% K₂SO₄), calcinated (850 °C) and characterized by Atomic Force Microscopy (AFM) which produced 93.2% w/w FAME (biodiesel) at relatively mild condition (5% catalyst, 65 °C, 3 h, 18:1 molar ratio) using CaO. Whereas, MgO, ZnO, and TiO₂ produced 92.4%, 72.5%, and 31.8% w/w FAME, respectively at elevated condition (225 °C). Thus, CaO was considered to be the best catalyst among the others. This tri-phase reaction require continuous fast mixing and the yield depends on the reaction parameters like catalyst amount, temperature, reaction time and molar ratio (methanol: oil). The reusability of these heterogeneous catalysts simplified the purification step, reduced the waste generation and make the final product technically and economically viable.     

Preparation of jet engine range fuel from biomass pyrolysis oil through hydrogenation and its comparison with aviation kerosene

The Bio-oil was produced from the pyrolysis of agricultural wastes (Eucalyptus sawdust) and discarded soybean frying oil. The temperature of the pyrolysis system was initiated at 28°C and increased to 850°C. Atmospheric distillation of crude bio-oil was performed and a fraction at a temperature range 160–240°C (pyrolysis oil) was separated and subjected to GC-MS, ¹H-NMR, TGA and FTIR analysis to identify the different properties and compounds present in pyrolysis oil. It was noticed that there was an abundance of oxygen and nitrogen containing compounds as well as other reactive species in pyrolysis oil. To reduce the amount of these species, the pyrolysis oil was subjected to hydrogenation in the presence of NiMo as a catalyst. After hydrogenation, the atmospheric distillation of hydrogenated bio-oil was performed and another fraction at temperature range 160–240°C (hydrogenated bio-oil) was separated and analyzed by the same techniques. It was noticed that during hydrogenation, more than 60% oxygenated and other reactive species were converted into hydrocarbons. Hydrogenated bio-oil showed very similar physico-chemical properties such as distillation curve, density, viscosity, freezing point, flash point, the presence of hydrocarbons and enthalpy of combustion as aviation kerosene also known as QAV-1.     

Production of soybean ethanol-based biodiesel using CaO heterogeneous catalysts promoted by Zn,K and Mg

This article focuses on the optimization of the production of fatty acid ethyl esters from soybean oil using CaO-based heterogeneous catalysts. Three different catalytic promoters were evaluated: Magnesium, zinc, and potassium. The reaction has evaluated the promoter content (promoter to calcium molar ratio), catalyst load, alcohol to oil molar ratio, and temperature. Response surface methodology (RSM) was used to evaluate the influence of each variable on the yield of biodiesel. The addition of K₂O or MgO in the catalyst has enhanced the yield in fatty acid ethyl esters, while the use of ZnO as a promoter was not successful.     

Biodiesel synthesis and characterization using welted thistle plant (Carduus acanthoides) as source of new non-edible seed oil

In this work we applied base catalyzed transesterification to convert non-edible welted thistle oil (Carduus acanthoides) as new non-edible feedstock into biodiesel (Fatty acid methyl esters). The highest biodiesel yield of 88% was obtained using optimized reaction conditions of 70°C and 5:1 molar ratio (methanol:oil). The synthesized esters were characterize and confirmed by the application of NMR and FT-IR techniques. Gas chromatography and mass spectroscopy identified different fatty acids as palmatic acid (C16:0), oleic acid (C18:1), linoleic acid (18:2), arachidic acid (C20:0), eicosanic acid (C20:1), and erucic acid (C22:1) in the oil of welted thistle. Six corresponding methyl esters reported in welted thistle oil biodiesel includes 9-hexadecenoic acid, hexadecanoic acid, 9-octadecadienoic acid, 11-eicosanoic acid, eicosanoic acid and 13-docosenoicacid. Fuel properties, such as density @40°C Kg/L (0.8470), kinematic viscosity @ 40°C c St (4.37), flash point (95°C), cloud point (+4°C), pour point (?5°C), and sulfur contents (0.0112% wt) of the biodiesel produced were compatible with American Society for Testing and Materials D 6751 specifications.