Homogeneous catalysed biodiesel synthesis from Alexandrian Laurel (Calophyllum inophyllum L.) kernel oil using ortho-phosphoric acid as a pretreatment catalyst

In this study, a non-edible seed oil of Alexandrian Laurel (Calophyllum inophyllum L.) with higher free fatty acid content has been harnessed to produce biodiesel by transesterification process. The 20.2% free fatty acid (FFA) content was first reduced to 12.9% by using TOP degumming process. Ortho-phosphoric acid was used to esterify the refined kernel oil. Transesterification reaction was performed with NaOH as an alkaline catalyst and methanol as an analytical solvent. The effects of methanol to oil molar ratio (MR), catalyst concentration (CC), reaction temperature (TP), reaction time (TM), and stirrer speed (SS) on biodiesel conversion were studied to optimize the transesterification conditions using DOE- approach. The experimental study revealed that 9:1 MR, 0.8 wt.% CC, 60°C TP, 75 min TM and 1000 rpm SS were the optimal process control variables. The study indicated that CC was the most important control parameter in optimal methyl ester production. The optimal treatment combination yielded 97.14% of biodiesel. The profile of biodiesel was determined using gas chromatography-mass spectrometry. ¹H NMR spectrum of Calophyllum inophyllum methyl ester (CIME) has been reported. The properties of the biodiesel have been found within specifications of the ASTM D6751 and EN 14214 standards and hence could be considered as a suitable alternative to diesel fuel for sustainable circulation of carbon.     

Assessment of biomass and lipid productivity and biodiesel quality of an indigenous microalga Chlorella sorokiniana MIC-G5

Generation of biodiesel from microalgae has been extensively investigated; however, its quality is often not suitable for use as fuel. Our investigation involved the evaluation of biodiesel quality using a native isolate Chlorella sorokiniana MIC-G5, as specified by American Society for Testing and Materials (ASTM), after transesterification of lipids with methanol, in the presence of sodium methoxide. Total quantity of lipids extracted from dry biomass, of approximately 410–450 mg g^?1 was characterized using FTIR and ¹H NMR. After transesterification, the total saturated and unsaturated fatty acid methyl esters (FAMEs) were 43% and 57%, respectively. The major FAMEs present in the biodiesel were methyl palmitate (C16:0), methyl oleate (C18:1), and methyl linoleate (C18:2), and the ¹H NMR spectra matched with criteria prescribed for high-quality biodiesel. The biodiesel exhibited a density of 0.873 g cm^–3, viscosity of 3.418 mm² s^?1, cetane number (CN) of 57.85, high heating value (HHV) of 40.25, iodine value of 71.823 g I₂ 100 g^?1, degree of unsaturation (DU) of 58%, and a cold filter plugging point (CFPP) of –5.22°C. Critical fuel parameters, including oxidation stability, CN, HHV, iodine value, flash point, cloud point, pour point, density, and viscosity were in accordance with the methyl ester composition and structural configuration. Hence, C. sorokiniana can be a promising feedstock for biodiesel generation.     

Scleropyrum pentandrum (Dennst.) mabb—oil as a feedstock for biodiesel production—engine performance and emission studies

A feasibility study on utilization of non edible oil of Scleropyrum pentandrum was carried out to see its potential as a new source for biodiesel production. Nonedible oil seeds of Scleropyrum pentandrum have oil content of 55–60%. Transesterification of freshly extracted oil in the presence of anhydrous sodium hydroxide at a concentration 1% (w/v oil) and methanol-oil ratio of 40% (v/v oil) yields 90.8% methyl esters under conventional heating. Month old oil requires sulfuric acid pretreatment (esterification) before transesterification. The transesterified oil has a density 889–893 kg/m³; kinematic viscosity of 4.21–5.7 mm²/s; cetane index 46.03; pour point of ?15°C and gross calorific value of 40.135 MJ/kg and oxidative stability of 2.35 hours. The properties are well within the Indian, European and American standard limits recommended for biodiesel except the oxidation stability, which can be improved by adding antioxidant additives. The engine performance studies of B10 and B20 blends of Scleropyrum pentandrum biodiesel (SP biodiesel) with statistical inference confirmed that it can be used as a fuel in CI engines without any engine modifications. The engine exhaust emission analysis showed that the emission of hydrocarbons can be minimized by at least 15–20%, CO emission by 15%, smoke opacity by 10–12% and moderately lesser CO₂ and NOx emissions.     

Optimization of esterification of fatty acid rubber seed oil for methyl ester synthesis in a plug flow reactor

To date, non-food vegetable oil has been considered as the primary source for biodiesel production. Rubber seed oil has high acid value (34 mgKOH/g) and can be used for biodiesel synthesis. The purpose of this study was to investigate esterification of fatty acid, which derived from rubber seed oil, in a plug flow reactor system at high temperature and low methanol consumption. Response surface methodology was applied for design experiment and optimization of esterification reaction. Temperature, methanol consumption, and sulfuric acid were chosen as variables to examine their influence in a conversion to methyl ester. At 140°C, at 5:1 methanol to fatty acid ratio (by mole), H₂SO₄ 1.5 (%v/w), and space time 20 min, the conversion to methyl ester attained 98.2%. Fourier transform infrared spectroscopy (FTIR) and gas chromatography-Mass spectrometry (GC-MS) were used for analysis and to confirm the formation of methyl ester. Methyl ester was characterized for biodiesel fuel properties in accordance to ASTM standard.     

Optimization of extraction of oil and biodiesel from Thespesia populnea seed oil by alkali catalyst in India

Thespesia populnea oil was new source of biodiesel. Crude Thespesia populnea oil was used as feedstock for biodiesel production by alkali-catalyzed methanolysis. The reaction in the presence of NaOH as catalyst was carried out to investigate the optimum conditions and to study the effects of variables on the reaction. A methanol to oil ratio of 6:1, sodium methoxide catalyst concentration of 1.5%, mixing intensity of 250 rpm and reaction temperature of 60°C offered the best Thespesia populnea seed oil methyl esters (biodiesel) yield (92.6%). The methyl ester content under these optimum conditions was 92.6% w/w, and all of the measured properties of the Thespesia populnea biodiesel (TPME) met the international standards ASTM D 6751-02. The results reveal that all of the reaction variables in this study had positive effects on the reaction. The results of the present study indicated that TPME could be a potential alternative to petrodiesel     

Production and characterization of biodiesel from Eriobotrya Japonica seed oil: an optimization study

Biodiesel is now-a-days recognized as a real potential alternative to petroleum-derived diesel fuel due to its number of desirable characteristics. However, its higher production cost resulting mainly due to use of costly food-grade vegetable oils as raw materials is the major barrier to its economic viability. Present work is an attempt to explore the potential of Eriobotrya japonica seed oil for the synthesis of biodiesel using alkali-catalyzed transesterification. Optimization of production parameters, namely molar ratio of alcohol to oil, amount of catalyst, reaction time and temperature, was carried out using Taguchi method. Fatty acid composition of both oil and biodiesel was determined using GC and H¹ NMR. Alcohol to oil molar ratio of 6:1, catalyst amount of 1% wt/wt, 2 h reaction time and 50 ^°C reaction temperature were found to be the optimum conditions for obtaining 94.52% biodiesel. Highest % contribution was shown by the ‘amount of catalyst’ (67.32%) followed by molar ratio of alcohol to oil (25.51%). Major fuel properties of E. japonica methyl esters produced under optimum conditions were found within the specified limits of ASTM D6751 for biodiesel, hence it may be considered a prospective substitute of petro-diesel.     

Garcinia gummi-gutta (L.) Robs.: A promising feedstock for biodiesel production

In the present study crude Garcinia gummi-gutta seed oil was evaluated as a potential feedstock for biodiesel production. Due to the high acid value (29.73 mg KOH/g) the oil was converted to biodiesel by using acid catalyzed esterification process. Further, biodiesel properties of the sample were evaluated, which fulfilled the biodiesel specifications laid by ASTM D6751, EN 14214 and IS 15607. The biodiesel possessed excellent cetane number (66.09) and a high flash point (158°C). In addition, the calorific value (41.03 MJ/kg) was very close to diesel fuel. The results suggest that the G. gummi-gutta can be an alternative source for diesel and can be used as a potential feedstock for biodiesel in India.     

A process model to estimate the cost of industrial scale biodiesel production from waste cooking oil by supercritical transesterification

This paper describes the conceptual design of a production process in which waste cooking oil is converted via supercritical transesterification with methanol to methyl esters (biodiesel).Since waste cooking oil contains water and free fatty acids, supercritical transesterification offers great advantage to eliminate the pre-treatment capital and operating cost.A supercritical transesterification process for biodiesel continuous production from waste cooking oil has been studied for three plant capacities (125,000; 80,000 and 8000 tonnes biodiesel/year). It can be concluded that biodiesel by supercritical transesterification can be scaled up resulting high purity of methyl esters (99.8%) and almost pure glycerol (96.4%) attained as by-product.The economic assessment of the biodiesel plant shows that biodiesel can be sold at US$ 0.17/l (125,000 tonnes/year), US$ 0.24/l (80,000 tonnes/year) and US$ 0.52/l for the smallest capacity (8000 tonnes/year).The sensitive key factors for the economic feasibility of the plant are: raw material price, plant capacity, glycerol price and capital cost.Overall conclusion is that the process can compete with the existing alkali and acid catalyzed processes.Especially for the conversion of waste cooking oil to biodiesel, the supercritical process is an interesting technical and economical alternative.     

Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Transesterification of Caesalpinia eriostachys seed oil using heterogeneous and homogeneous basic catalysts

Caesalpinea eriostachys seed oil, as a source of triglycerides with potential application for biodiesel production in Mexico is introduced. Its lipid profile obtained by Gas Chromatography-Mass Spectrometry (GC-MS) revealed saturated and unsaturated glycerol esters as the constituents. Therefore, heterogeneous and homogeneous catalyzed transesterification reactions were assayed employing ZnAl hydrotalcites and KOH, as the catalysts, respectively. The transesterification reactions yielded 59% for Zn/Al(2), 79% for Zn/Al(4), and 90% for KOH, depicting typical behavior, as in biodiesel production data from literature, where Zn-Al hydrotalcites or KOH were assayed. The caloric, density, viscosity values, and fatty acid methyl esters profile from reaction products were concordant to EN 14214, suggesting C. eriostachys as a promising feedstock for biodiesel production.     

Biodiesel production from a free fatty acid containing Karanja oil by a single-step heterogeneously catalyzed process

Karanja oil, containing 6.2% free fatty acids (FFAs), was considered for biodiesel production using a single-step solid-phase acid catalyzed process. Different types of zeolites and Amberlyst15 catalysts were tested and biodiesel was produced. Under similar conditions, the highest biodiesel yield was achieved using an Amberlyst15 catalyst, which contained 3–5% of moisture. The effects of operating parameters of the reaction such as reaction temperature, catalyst amount, and methanol-to-oil ratio were studied. An increase of methanol:oil ratio revealed a non-monotonic increase in biodiesel yields. Similar non-monotonic behavior was observed when Jatropha oil was used. Leaching and catalyst reusability were also considered. No significant effects of leaching were observed and catalyst reusability appeared to be affected by methanol interactions. The presence of a co-solvent, Tetrahydrofuran (THF), increased the biodiesel yield. Furthermore, an optimum amount of THF (THF:methanol volume ratio of 1:2) gave rise to the highest biodiesel yield. A biodiesel yield of 93% was achieved at 120 °C using a single-step process with Amberlyst15 as a catalyst, THF as a co-solvent, and a methanol:oil ratio of 30:1.     

Experimental evaluation of the catalytic efficiency of calcium based natural and modified catalyst for biodiesel synthesis

Transesterification of a mixture of vegetable oils with methanol using metal oxide catalysts derived from snail shell (SS) for biodiesel production was investigated. The metal oxides obtained from calcined snail shells in the temperature range of 650°–950 °C and modified by loading different potassium salts were used as a catalyst in the process. The catalysts were characterized by FT-IR, XRD, SEM-EDS, XPS and TGA. Catalytic activities of developed catalysts were also tested by Hammet indicator method and ion exchange method. The best calcination conditions were observed at 850°C for 4 hours based on biodiesel yield. The KF loaded snail shell gave highest biodiesel yield of 98 ± 1% in a batch reactor with highest basicity (15.9 mmoles/g) and basic strength measured by Hammet method. The optimized reaction conditions were: reaction temperature 65°C, reaction time 3 hours, methanol to oil molar ratio 9:1 and catalyst concentration 3wt%. Leaching and reusability tests confirm the stability of the catalyst as it encounters only 3% of leaching and small changes in catalytic activity up to five runs in terms of biodiesel yield.     

Clam shell catalyst for continuous production of biodiesel

Continuous flow transesterification of waste frying oil (WFO) with methanol for the biodiesel production was tested in a laboratory scale jacketed reactive distillation (RD) unit packed with clam shell based CaO as solid catalyst. The physiochemical properties of the clam shell catalysts were characterized by X-ray Diffraction (XRD), Brunauer–Emmett–Teller (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive Atomic X-ray Spectrometry (EDAX). The effects of the reactant flow rate, methanol-to-oil ratio, and catalyst bed height were studied to obtain the maximum methyl ester conversion. Reboiler temperature of 65°C was maintained throughout the process for product purification and the system reached the steady state at 7 hr. The experimental results revealed that the jacketed RD system packed with clam shell based CaO showed high catalytic activity for continuous production of biodiesel and a maximum methyl ester conversion of 94.41% was obtained at a reactant flow rate of 0.2 mL/min, methanol/oil ratio of 6:1, and catalyst bed height of 180 mm.     

Possibility of converting indigenous Salvadora persica L. seed oil into biodiesel in Pakistan

In this research study, biodiesel has been successfully produced from vegetable seed oil of an indigenous plant Salvadora persica L. that meets the international biodiesel standard (ASTM D6751). The biodiesel yield was 1.57 g/5 g (31.4% by weight) and the in-situ transesterification ester content conversion was 97.7%. The produced biodiesel density was 0.894 g/mL, its kinematic viscosity 5.51 mm²/s, HHV 35.26 MJ/kg, flash point 210°C, cetane no. 61, and sulfur content 0.0844%. Thermal analysis of the biodiesel showed that 97% weight loss was achieved at 595°C with total oxidation of the biodiesel. The production energy efficiency was 0.46% with a lab scale setup, assuming the volume fraction ratio (volume of the sample/total volume of the equipment used). The results revealed that single-step in-situ transesterification method is suitable for the production of biodiesel from S. persica seed oil.     

Ferric-manganese doped sulphated zirconia nanoparticles catalyst for single-step biodiesel production from waste cooking oil: Characterization and optimization

Biodiesel of waste cooking oil origin is gaining attention as a replacement for current fossil fuels, as its low-priced, recycled feedstock shall prevent food source competition, which is estimated to happen with current biodiesel production processes. As a result, waste cooking oil has been claimed to be a highly potential feedstock for biodiesel production. In the present research work, Fe-Mn doped sulphated zirconia catalyst was synthesized and used in simultaneous esterification and transesterification of waste cooking oil to biodiesel synthesis. The catalyst was prepared through the impregnation method and characterized by using XRD, TPD-NH_3, FT-IR, BET, and TEM. Response surface methodology (RSM) in conjunction with the central composite design (CCD) was applied to statistically evaluate and optimize the biodiesel preparation process. It was found that the synthesis of biodiesel achieved an optimum level of 97.2% waste cooking oil methyl ester’s (WCOME’s) yield at the following reaction conditions: methanol/oil molar ratio: 10:1, catalyst concentration: 3.0 wt %, and reaction temperature: 160 °C. The extremely high WCOME’s yield of 97.2% was proved to be due to high acidity, surface area, and large pore diameter; reactants can easily diffuse into the interior pore of the catalyst and allow them to be in contact with active sites that enhance catalytic activity.     

A comprehensive review on biodiesel production using Moringa oleifera oil

Biodiesel has emerged as one of the most promising renewable energy to substitute existing petroleum-derived diesel fuel being used in transportation sectors. Among the various feedstocks reported for biodiesel production, Moringa oleifera oil is becoming a promising replacement for conventional diesel fuel. Therefore, this work provides a comprehensive overview of the recent progress in biodiesel production from Moringa oleifera oil. The physicochemical properties, fatty acid composition of oil and methyl esters, oil extraction methods, esterification, and transesterification process, and purification methods employed in the biodiesel production have been discussed.     

The effect of cerium oxide additive on the performance and emission characteristics of a CI engine operated with rice bran biodiesel and its blends

In this study, the rice bran oil (RBO) has been converted into methyl ester with an aid of transesterification reaction. Chemically, transesterification means conversion of triglyceride molecule or a complex fatty acid into alcohol and ester by removing the glycerin and neutralizing the free fatty acids. The B20 blend samples [80% diesel + 20% biodiesel] were prepared for each methyl ester obtained from RBO and then the cerium oxide (CeO₂) nanoparticles were added to the each B20 blend samples at a dosage of 50 ppm and 100 ppm with an aid of ultrasonicator. Moreover, in the absence of any engine modifications, the performance and emission characteristics of those blend samples have been investigated from the experimentally measured values such as density, viscosity, cloud point, pour point, and calorific value while the engine performance was also analyzed through the parameters like exhaust gas temperature (EGT), brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), exhaust emission of carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx). The experimental results reveal that the use of CeO₂ blended biodiesel in diesel engine has exhibited good improvement in performance characteristic and reduction in exhaust emissions.     

Nanocatalyzed biodiesel synthesis from the oily contents of Marine brown alga Dictyota dichotoma

This research article demonstrates biodiesel synthesis through the methanolysis of the oily contents (4.02 ± 0.27% w/w on dried basis) of Dictyota dichotoma collected from the coast of Hawksbay, Pakistan. The metal oxides (CaO, MgO, ZnO, and TiO₂) used as nanocatalysts were refluxed (5% K₂SO₄), calcinated (850 °C) and characterized by Atomic Force Microscopy (AFM) which produced 93.2% w/w FAME (biodiesel) at relatively mild condition (5% catalyst, 65 °C, 3 h, 18:1 molar ratio) using CaO. Whereas, MgO, ZnO, and TiO₂ produced 92.4%, 72.5%, and 31.8% w/w FAME, respectively at elevated condition (225 °C). Thus, CaO was considered to be the best catalyst among the others. This tri-phase reaction require continuous fast mixing and the yield depends on the reaction parameters like catalyst amount, temperature, reaction time and molar ratio (methanol: oil). The reusability of these heterogeneous catalysts simplified the purification step, reduced the waste generation and make the final product technically and economically viable.     

Prospect of castor oil biodiesel in Bangladesh: Process development and optimization study

In this study, castor oil (CO) has been investigated as a potential source for biodiesel production in Bangladesh. Castor oil has been extracted from the seeds by mechanical press and the Soxhlet extraction method. Maximum oil content of 55.7% has been found by the Soxhlet extraction method. The physicochemical properties such as free fatty acid (FFA) content, kinematic viscosity, saponification value, and density of the oil have been measured by different standard methods. The FFA content and viscosity have been found considerably higher such as 33.5% and 253 mm²/s, respectively. Biodiesel has been prepared using a three-step method comprising of saponification of oil followed by acidification of the soap and esterification of FFA. The overall yield of FFA from CO is found to be around 89.2%. The final step is esterification that produces fatty acid methyl ester (FAME) and a maximum 97.4% conversion of FFA to biodiesel has been observed. The effect of the oil to methanol molar ratio, catalyst concentration, reaction temperature, and time has been investigated for esterification reaction and optimized using the response surface methodology. ¹H NMR of crude castor oil and castor oil methyl ester (COME) was studied and analyzed that confirms the complete conversion of castor oil to biodiesel. Finally, the biodiesel, produced under optimum conditions, was characterized using the various standard method and found comparable with petro-diesel and biodiesel standard.     

Optimization of biodiesel production from waste cooking oil using ion-exchange resins

Waste cooking oil is a potential substitution of refined vegetable oil for the production of biodiesel due to the low cost of raw material and for solving their disposal problem. In this study, optimization of esterification process of free fatty acids in artificially acidified soybean oil with oleic acid has been carried out using methanol as an agent and ion exchange resin as a heterogeneous catalyst. The esterification reaction has been investigated based on the mass balance of the developed model. The model has been validated against experimental data and effects of temperature and catalyst weight have been analyzed. Thereafter, optimization process has been fulfilled for two different objective functions as conversion of acid oil and benefit. Optimization results indicated that the maximum conversion of acid is 95.95%, which is achievable at 4.48-g catalyst loading and reaction temperature of 120°C. Maximum benefit was obtained as US$0.057 per batch of reaction at a catalyst amount of 1 g and temperature of 120°C.