电解质种类对电催化氧化降解苯酚的影响

研究了不同电解质对有机物电催化氧化性能的影响。以高温热解法制备了Ti/SnO2+Sb2O3阳极,用SEM和XRD对电极结构进行了表征。以苯酚为目标有机物,考察了Na2SO4、NaCl和NaNO33种不同电解质对苯酚降解效果的影响。用循环伏安法研究了苯酚在不同支持电解质条件下的电化学行为。采用碘量法测定了在不同电解质溶液中氧化性物质的生成量。研究结果表明,电极的活性涂层主要由SnO2和微量的Sb2O3组成,均匀完整地覆盖住了Ti基体表面。以NaCl为支持电解质时苯酚降解效果明显优于用Na2SO4、NaNO3为支持电解质,并且苯酚的降解主要以电极表面电化学生成的HClO和ClO-的间接化学氧化为主。以Na2SO4为支持电解质时有利于降低和稳定槽电压。在3种电解质条件下,苯酚的降解均遵循一级反应动力学规律。在降解过程中NaCl溶液中生成的氧化性物质浓度最大,且随降解时间延长逐渐增大。     

电化学氧化与生物法联合降解木质素的影响因素

采用高效的电化学氧化技术联合低成本的生物降解技术,进行了木质素的降解探索。考察了电流密度、电量、初始p H和电解质浓度对木质素降解效果的影响,结果表明,电流密度和电量影响显著,而初始p H和电解质浓度的影响较小。经过综合比较,得到电化学与生物联合降解木质素的最佳反应条件为:电流密度为5.0 m A/cm2;电量为20 k C;初始p H为7;电解质浓度为0.1 mol/L。在此条件下,碱木质素和木质素磺酸钠的COD去除率分别达到65.97%和59.31%,表征木质素酚羟基结构的UV280分别降低了65.97%和59.77%,色度去除率分别为74.15%和58.32%。总之,电化学前处理可破坏木质素的关键结构,提高木质素的可生化性,从而促进加快后续生物降解。     

电解液条件对苯酚降解及羟自由基生成的影响

以钛基Pb O2电极为活性阳极,通过电化学氧化法降解处理苯酚模拟废水,系统考察了羟自由基(·OH)抑制剂、支持电解质、酸碱性等电解液条件对苯酚水溶液COD去除率的影响。同时,以水杨酸(SA)为·OH捕捉剂,通过高效液相色谱分析技术对不同电解液条件下·OH的生成量进行间接检测。结果发现,Pb O2电极上苯酚水溶液的COD去除符合一级反应动力学规律,其表观反应速率常数在分别加入·OH抑制剂Na HCO3、Na2CO3和叔丁醇时显著下降,表明苯酚的电化学氧化降解遵循·OH反应机理;支持电解质对电解液体系中·OH生成量的影响不明显,主要通过在阳极氧化生成的氧化剂参与苯酚的降解,以Na Cl为支持电解质时降解效率最高,其次是Na2SO4,最后为Na NO3;随电解液p H值的增加,苯酚水溶液的COD去除速率不断提高,而·OH的生成量在碱性条件下亦显著增加。     

钛基锡锑阳极电化学氧化去除水中的四环素

以钛基锡锑电极为阳极,研究了电化学氧化技术对水中四环素的去除效果。考察了电流密度(5~25 mA·cm~(-2))、极板间距(5~25 mm)、四环素初始浓度(5~100 mg·L~(-1))和电解质种类(NaClO_4、Na_2SO_4和NaNO_3)对四环素电化学降解效率的影响。研究表明:钛基锡锑电极电化学降解四环素反应符合一级反应动力学规律(R~20.95);四环素降解效率随电流密度增大而增大,当电流密度大于15 mA·cm~(-2)时,四环素的降解反应受传质控制;四环素降解效率随极板间距增大而减小,在传质控制条件下,反应速率与极板间距成反比;初始浓度小于20 mg·L~(-1)时,受传质影响,四环素降解效率基本不随初始浓度变化,当初始浓度大于20 mg·L~(-1)时,四环素降解效率随初始浓度增大而减小;Na_2SO_4为电化学降解水中四环素较合适的电解质。     

旋转盘反应器光催化降解苯酚废水动力学

采用旋转盘反应器(SDR)降解苯酚废水,对苯酚初始浓度、溶液p H值、H2O2的添加对其光催化降解动力学的影响进行了研究。结果表明,SDR内的光催化降解动力学特征符合一级反应动力学规律。苯酚初始浓度越低,反应速率常数k值越大;溶液p H=2时的降解速率高于其他p H值;H2O2的协同作用使苯酚的降解速率明显提高,其速率常数k值为未添加H2O2时的78倍。     

吸附-电化学氧化耦合处理对氯苯酚废水及动力学

以毡状活性炭纤维为阳极,不锈钢为阴极,吸附-电化学氧化耦合降解对氯苯酚废水进行了研究。考察了吸附或耦合电化学氧化过程、电流密度、支持电解质硫酸钠浓度和活性炭纤维重复使用对废水COD去除率的影响,结果表明,采用吸附-电化学氧化耦合方法,当电流密度7.6 mA/cm2支持电解质（硫酸钠）浓度为1 g/L,处理时间为180 min,4-CP废水COD去除率可达97.09%。毡状活性炭纤维对4-CP的静态吸附过程符合Langmiu吸附等温方程。建立了吸附-电化学氧化COD去除动力学模型,动力学模型参数表明,对于COD的去除,电化学氧化作用比吸附作用大。     

CoFe_2O_4/TiO_2/鳞片石墨粒子电极光电催化降解罗丹明B

采用溶胶-凝胶法制成CoFe_2O_4/TiO_2/鳞片石墨粒子电极,用电子扫描电镜(SEM)、X-射线衍射仪(XRD)和X-射线光电子能谱仪(XPS)对该粒子电极的形貌、晶体结构和元素组成进行分析,并将其应用于罗丹明B(Rh B)的光电催化实验;考察电解质浓度、粒子电极投加量、电压、pH和初始浓度等因素对罗丹明B降解的影响,并研究了罗丹明B的光电催化降解动力学。结果表明:光催化和电化学联合作用时,产生协同作用;在电解质Na_2SO_4溶液浓度为0.03 mol·L~(-1),粒子电极投加量为6.67 g·L~(-1),外加电压为8 V,pH为3,反应时间为45 min时,浓度为15 mg·L~(-1)的罗丹明B的去除率达到97.6%;罗丹明B的光电催化降解反应符合假一级动力学模型。     

MnO2催化Fenton试剂降解苯酚废水

实验对MnO2催化Fenton试剂氧化高浓度苯酚废水的动力学特性和去除效果进行了研究。结果表明,MnO2可以提高Fenton试剂体系对苯酚的降解率以及COD的去除率;Fenton试剂以及MnO2催化Fenton试剂氧化苯酚废水体系中苯酚的降解都符合拟一级动力学模型。在MnO2催化Fenton试剂氧化体系中,苯酚的降解速率常数有明显提高,反应活化能也有所降低,说明MnO2的加入可以使反应容易进行。废水降解前后紫外可见吸收光谱和红外谱图表明,Fenton试剂法将苯酚可能降解为羧酸、烯烃等有机物中间体。     

高铁酸盐氧化降解水中苯酚的动力学及机理研究

以自制高铁酸钾(K₂FeO₄)为原料，探讨了影响高铁酸盐氧化降解苯酚的主要因素，并研究了苯酚降解的动力学特征和反应机理。结果表明，高铁酸盐加入量、pH值、持续搅拌、反应温度、反应时间都影响苯酚去除效果。其中高铁酸盐加入量是影响苯酚去除效果的关键因素，高铁酸盐氧化降解苯酚的最佳pH值范围为9～10，持续搅拌和提高反应温度只影响苯酚降解速率而不影响苯酚降解率。苯酚的降解过程遵循一级反应动力学模型。苯酚被高铁酸盐氧化生成CO₂、H₂O以及一部分难矿化的有机物。     

苯酚降解研究

连续反应器生物氧化技术处理低浓度苯酚废液正受到重视。评价连续反应器运作的关键因素之一是反应速率动力学描述。M．Shishido和M．Toda通过分析溶解氧浓度的变化，测定了低浓度条件下苯酚微生物降解的动力学。他们采用了三种动力学模式来表达苯酚消耗速率。当起始浓度在30mg／L以下时，所有模式均能很好地表达苯酚降解特性。在苯酚浓度低于10mg／L时，只有联合的动力学模式才能准确地表达。苯酚降解研究@舟人     

The role of ferrous ion in Fenton and photo-Fenton processes for the degradation of phenol

The efficiency of different Fenton-related oxidative processes such as Fenton, solar-Fenton and UV-Fenton were examined using phenol as a model compound in simulated and industrial wastewater. A batch study was conducted to optimize parameters like pH, hydrogen peroxide concentration and ferrous ion concentration governing the Fenton process. At optimum conditions, different Fenton-related processes were compared for the degradation of phenol. Increased degradation and mineralisation efficiency were observed in photo-Fenton processes as compared to conventional Fenton process. The maximum mineralising efficiency for phenol with Fenton, solar and UV-Fenton processes were 41%, 96% and 97% respectively. In Fenton process, carboxylic acids like acetic acid and oxalic acid were formed as end products during the degradation of phenol while in photo-Fenton processes, both these ions were identified during the early stages of phenol degradation and were oxidized almost completely at 120 min of the reaction time. In photo-Fenton processes (solar and UV light) complete degradation were observed with 0.4 mM of Fe2+ catalyst as compared to 0.8 mM of Fe2+ in conventional Fenton process. In Fenton and solar-Fenton processes, an iron reusability study was performed to minimize the amount of iron used in treatment process. The efficacy of Fenton and solar-Fenton processes was applied to effluent from phenol resin-manufacturing unit for the removal and mineralisation of phenol.     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

Simultaneous photocatalytic reduction of Cr(VI) and oxidation of phenol over monoclinic BiVO4 under visible light irradiation

BiVO4 powder with monoclinic structure was prepared and used as a visible-light catalyst simultaneously for the photooxidation of phenol and the photoreduction of Cr(VI). The photocatalytic efficiency was found to be rather low for either single phenol solution or single Cr(VI) solution. However, the photocatalytic reduction of Cr(VI) and photocatalytic oxidation of phenol proceed more rapidly for the coexistence system of phenol and Cr(VI) than for the single process, showing synergetic effect between the oxidation and reduction reactions. For the simultaneous photocatalytic reduction-oxidation process, the first-order kinetic constant of phenol degradation was 0.0314 min-1, being about six times higher than that for the photocatalytic process of single phenol. This result reveals the feasibility of using Cr(VI) as the electron scavenger of mBiVO4-mediated photocatalytic process of phenol degradation, and gives us an enlightenment to employ other semiconductor with a better visible light response but with a more positive band edge to efficiently degrade organic pollutants. This is the first report for simultaneous photocatalytic reduction of Cr(VI) and removal of phenol under visible light irradiation using photocatalyst mBiVO4.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

两相分配式生物反应器处理高盐废水中的苯酚

采用新型两相分配式生物反应器(TPPB)和前期研究得到的高效苯酚降解菌对高盐废水中苯酚的降解进行研究,研究中确定煤油为反应系统的最佳有机溶剂,并考察了废水苯酚含量、废水盐度以及搅拌器搅拌速度对苯酚降解的影响。结果表明,反应系统能正常降解苯酚含量为1 000～2 500 mg/L的高盐苯酚废水;反应系统在含盐量为100 g NaCl/L、搅拌速度为50 r/min的运行工况条件下,降解时间缩短为52 h,总酚去除率为20.58 mg/(L.h)。     

CuO / 过硫酸氢钾体系催化氧化苯酚简

本论文通过直接沉淀法制备了CuO催化剂，结合过硫酸氢钾，在常温常压下催化氧化处理苯酚模拟废水。采用电子显微镜（SEM）、X射线粉末衍射（XRD）对催化剂进行了表征，并研究了反应过程中各影响因素对降解效率的影响。实验结果表明，在催化剂用量为0.2 g/L，氧化剂浓度为0.25 g/L，pH值为7，反应时间为60 min的条件下，浓度为50 mg/L的苯酚降解率可达100%，TOC去除率达84%。进一步实验表明，催化剂具有良好的重复使用能力。最后，通过自由基捕捉实验，考察了体系中的自由基种类，并根据实验结果，讨论了CuO/过硫酸氢钾体系的催化降解机理。     

Shewanellasp．XB缺氧反硝化降解苯酚

苯酚的生物降解一直受到关注。以苯酚为惟一电子供体，研究了Shewanellasp．XB对苯酚的缺氧降解特性。研究结果表明，在反硝化条件下，当C／N为13．3时，苯酚可以完全降解，NO2--N积累量很少。另外，当加入氧化还原介体，如核黄素3μmol／L、AQDS0．01mmol／L、AQS0．05mmol／L和LQ0．01mmol／L时，苯酚降解速率分别为不加介体时的1．45、1．77、1．67和1．63倍。当以氯化铵代替硝酸盐时，苯酚也能进行厌氧发酵降解。另外，菌株XB反硝化降解苯酚可能是厌氧和好氧降解的混合过程。     

苯酚的厌氧生物处理

采用不断增加苯酚浓度而降低葡萄糖浓度的方法可驯化厌氧污泥中的微生物，使厌氧污泥最终以苯酚为唯一碳源生长，可显著提高厌氧污泥降解苯酚的能力；对苯酚间歇厌氧降解过程进行了分析。苯酚浓度在0～1.680 mg/L范围内，其厌氧降解过程符合一级动力学。Aiba模型、Haldane模型和Teisser 模型均可很好地描述处于对数期时厌氧污泥的比生长速率与初始底物浓度之间的关系，其中以Teisser 模型模拟的效果最好。将驯化污泥接种于UASB中可实现对含酚废水处理的连续运行，最大的有机负荷达2 g COD/（L·d），稳定运行时苯酚的去除率可维持在96%以上。