Development of regenerative dye impregnated mesoporous silica materials for assessing exposure to ammonia

The mesostructured materials MCM-41 and SBA-15 were studied as possible supports of bromocresol green (BG) dye impregnation for the ammonia gas detection because of their large surface area, high regenerative property, and high thermal stability. X-ray diffraction, transmission electron microscopy, scanning electron microscope, and N2 adsorption analysis were used to characterize the prepared materials. These materials could sense ammonia via visible color change from yellowish-orange to blue color. The color change process of the nanostructured materials was fully reversible during 10 cyclic tests. The results indicated that the ammonia absorption responses of the two nanostructured materials were both very sensitive, and high linear correlation and high precision were achieved. As the gaseous ammonia concentrations were 50 and 5 ppmv, the response times for the SBA-15/BG were only 1 and 5 min, respectively. Moreover the BG dye-impregnated SBA-15 was less affected by the variation in the relative humidity. It also had faster response for the detection of NH3, as well as lower manufacturing price as compared to that of the dye-impregnated MCM-41. Such feature enables SBA-15/BG to be a very promising material for the detection of ammonia gas.     

Co3O4/介孔分子筛催化剂对苯催化完全氧化的研究

分别以介孔分子筛MCM-41、MCM-48、SBA-15为载体，采用等体积浸渍法制备了氧化钴/介孔分子筛催化剂，利用N₂吸附、X射线衍射、程序升温还原等技术对催化剂进行了表征，考察了Co₃O₄的负载量及载体的孔结构对催化剂完全催化氧化苯的性能的影响。结果表明，Co₃O₄的负载量为20%时，催化剂的催化活性最好；载体的孔径和催化剂的可还原性能是影响催化活性的主要因素，催化剂活性顺序为Co₃O₄ /SBA-15> Co₃O₄ /MCM41> Co₃O₄ /MCM-48。     

Investigating the potential of functionalized MCM-41 on adsorption of Remazol Red dye

The modification of MCM-41 was performed with 3-aminopropropyltrimethoxysilane. The structural order and textural properties of the synthesized materials were studied by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetry/differential thermogravimetry, nitrogen adsorption, and desorption analysis. The adsorption capacity of NH₂-MCM-41 was studied with Remazol Red dye. The following parameters were studied in the adsorption process: pH, temperature, adsorbent dosage, and initial concentration. The desorption process was studied in different concentrations of NaOH solutions. The Freundlich isotherm model was found to be fit with the equilibrium isotherm data. Kinetics of adsorption follows the modified Avrami rate equation. The maximum adsorption capacity was estimated to be 45.9 mg?g^?1, with removal of the dye of 99.1 %. The NH₂-MCM-41 material exhibited high desorption capacity with 98.1 %.     

Adsorption of mesitylene via mesoporous adsorbents

Mesitylene (or 1,3,5-trimethylbenzene) is a volatile organic compound emitted from various industrial processes, e.g., spray coating. Its emissions have become a critical issue because mesitylene is toxic and cannot be removed using traditional adsorbents, e.g., zeolite (H-ZSM-5; the diameter of mesitylene molecules is greater than the pore size of H-ZSM-5). Hence, an adsorbent with a large pore size, MCM-41, is used in this study to investigate its adsorption capacity for mesitylene and compare with that of H-ZSM-5. Experimental results reveal that MCM-41 without Al₂O₃ exhibits a good adsorption capacity (184 mg/g) for the gas stream containing 100 ppm of mesitylene at a relative humidity of 10%. The adsorption kinetics is well described by the Freundlich isotherm. Furthermore, experimental results reveal that MCM-41 is effective for the adsorption of low concentrations (10 ppm) of mesitylene. In addition, adsorption–desorption tests revealed that the sample MCM-41-AS is stable to sustain the adsorption capacity after 10 adsorption–desorption cycles. After 10 adsorption–desorption cycles, MCM-41-AS retains 92.4% of its initial adsorption capacity (170 vs. 184 mg/g). Finally, MCM-41 and H-ZSM-5 in series are effective for the simultaneous removal of mesitylene and toluene in the gas stream.

Implications: This study aims to improve the performance of adsorbent for mesitylene, which is typically applied in the spray-coating industry. The zeolite MCM-41-AS is selected as a candidate for the investigation. Experimental results reveal that MCM-41-AS exhibits a good adsorption capacity for mesitylene and that it can be integrated with H-ZSM-5-25 for the simultaneous adsorption of mesitylene and toluene.     

Adsorption of basic dyes onto MCM-41

The adsorption of two basic dyes, Basic Green 5 (BG5) and Basic Violet 10 (BV10), onto MCM-41 was studied to examine the possible effect of interactions between large adsorbates and MCM-41 on the pore structure stability of MCM-41 and the potential of MCM-41 for the removal of basic dyes from wastewater. The revolutions of surface characteristics and pore structure of MCM-41 induced by dyes adsorption were characterized based on the analyses of the nitrogen isotherms, the XRD patterns, and the FTIR spectra. It was experimentally concluded that when the effect of interactions between large dyes (such as BV10) and MCM-41 on the pore structure stability of MCM-41 was insignificant, MCM-41 might be a good adsorbent for the removal of basic dyes from wastewater. The adsorption of BV10 on MCM-41 with respect to contact time, pH, and temperature was then measured to provide more information about the adsorption characteristics of MCM-41. Both Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the pseudo-second-order kinetic model was used to describe the kinetic data, from which some adsorption thermodynamic parameters were also evaluated.     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源，CTAB和PEG-6000为模板剂，合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌，并且以该样品为吸附剂，对含Cu²⁺的溶液进行了静态吸附实验。结果表明，以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41，其比表面积为869.5 m²/g，孔容为0.97 cm³/g，平均孔径为3.3 nm；溶液pH为5~6时，MCM-41对Cu²⁺的去除效果最好；MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g；MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明，该过程符合准二级动力学模型。     

Modified SBA-15 mesoporous silica for heavy metal ions remediation

N-Propylsalicylaldimino-functionalized SBA-15 mesoporous silica was prepared, characterized and used as an adsorbent for heavy metal ions. The organic-inorganic hybrid material was obtained using successive grafting procedures of SBA-15 silica with 3-aminopropyl-triethoxysilane and salicylaldehyde, respectively. For comparison an amorphous silica gel was functionalized using the same procedure. The structure and physicochemical properties of the materials were characterized by means of elemental analysis, X-ray diffraction (XRD), nitrogen adsorption-desorption, thermogravimetric analysis and FTIR spectroscopy. The organic functional groups were successfully grafted on the SBA-15 surfaces and the ordering of the support was not affected by the chemical modification. The behavior of the grafted solids for the adsorption of heavy metals ions from aqueous solutions was investigated. The hybrid materials showed high adsorption capacity and high selectivity for copper ions. Other ions, such as nickel, zinc, and cobalt were adsorbed by the modified SBA-15 material. The adsorbent can be regenerated by acid treatment without altering its properties.     

Study on the indoor volatile organic compound treatment and performance assessment with TiO2/MCM-41 and TiO2/quartz photoreactor under ultraviolet irradiation

Volatile organic compounds (VOCs) are the cause of indoor air pollution and are readily emitted from furniture and cleaning agents. In Taiwan, the concentrations of indoor VOCs range roughly from 1 to 10 ppm. It is important to effectively reduce indoor VOC emissions and establish the implementation of long-term, low-cost, controlled techniques such as those found in the ultraviolet/titanium dioxide (UV/TiO2) control systems. This study evaluates the performance of a photoreactor activated by visible irradiation and packed with TiO2/quartz or TiO2/mobile catalytic material number 41 (MCM-41). The photocatalysts tested include commercial TiO2 (Degussa P-25) and synthesized TiO2 with a modified sol-gel process. The UV light had a wavelength of 365 nm and contained an 8-W, low-pressure mercury lamp. Reactants and products were analyzed quantitatively by using gas chromatography with a flame-ionization detector. It is important to understand the influence of such operational parameters, such as concentration of pollutant, temperature, and retention time of processing. The indoor concentrations of VOCs varied from 2 to 10 ppm. Additionally, the temperatures ranged from 15 to 35 degrees C and the retention time tested from 2 to 8.2 sec. The results show that quartz with TiO2 had a better photoreductive efficiency than quartz with MCM-41. The toluene degradation efficiency of 77.4% with UV/TiO2/quartz was larger than that of 54.4% with the UV/TiO2/MCM-41 system under 10-min reaction time. The degradation efficiency of the UV/TiO2 system decreased with the increasing concentrations of indoor VOCs. The toluene degradation efficiency at 2 ppm was approximately 5 times greater than that at 10 ppm. The photoreduction rate of the VOCs was also evaluated with the Langmuir-Hinshewood model and was shown to be pseudo-first-order kinetics.     

Carbon dioxide adsorption on amine-impregnated mesoporous materials prepared from spent quartz sand

Mesoporous MCM-41 was synthesized using cetyltrimethyl ammonium bromide (CTAB) as a cationic surfactant and spent quartz sand as the silica source. Modification of the mesoporous structure to create an absorbent was then completed using 3-aminopropyltrimethoxysilane. Amine-Quartz-MCM (The A-Q-MCM) adsorbents were then characterized by N₂ adsorption/desorption, elemental analysis (EA), X-ray fluorescence (XRF), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), as well as the carbon dioxide (CO₂) adsorption/desorption performance. In this study, spent quartz sand was utilized to synthesize Quartz-MCM (Q-MCM) and the amine functionalized material, A-Q-MCM, which exhibited a higher uptake of CO₂ at room temperature compared with the nongrafted material. The results showed that Q-MCM is similar to MCM-41 synthesized using commercial methods. The surface area, pore volume, and pore diameter were found to be as high as 1028 m²/g, 0.907 cm³/g, and 3.04 nm, respectively. Under the condition of CO₂ concentration of 5000 ppm, retention time of 50 cc/min, and the dosage of 1 g/cm³, the mean adsorption capacity of CO₂ onto A-Q-MCM was about 89 mg/g, and the nitrogen content of A-Q-MCM was 2.74%. The adsorption equilibrium was modeled well using a Freundlich isotherm.

Implications:In this study, spent quartz sand was utilized to synthesize Q-MCM. The amine functionalized material exhibited a higher uptake of CO₂ at room temperature compared with the nongrafted material. The results showed that Q-MCM is similar to MCM-41 synthesized using commercial methods. The adsorption equilibrium was modeled well using a Freundlich isotherm.     

Gaseous Ammonia Uptake in Compost Biofilters as Related to Compost Water Content

Abstract

Sewage sludge and yard waste compost were used as biofilter materials and tested with respect to their capacity for removing ammonia from air at different water contents. Ammonia removal was measured in biofilters containing compost wetted to different moisture contents ranging from air dry to field capacity (maximum water holding capacity). Filters were operated for 15 days and subsequently analyzed for NH₃/NH₄ ⁺, NO₂ ^-, and NO₃ ^-. The measured nitrogen species concentration profiles inside the filters were used to calculate ammonia removal rates. The results showed that ammonia removal is strongly dependent on the water content in the filter material. At gravimetric water contents below 0.25 g H₂O g solids^-1 for the yard waste compost and 0.5 g H₂O g solids^-1 ammonia removal rates were very low but increased rapidly above these values. The sewage sludge compost filters yielded more than twice the ammonia removal rate observed for yard waste compost likely because of a high initial concentration of nitrifying bacteria originating from the wastewater treatment process and a high air-water interphase surface area that facilitates effective ammonia dissolution and transport to the biofilm.     

New catalyst comprising Silicotungstic acid and MCM-22 for degradation of some organic dyes

A heterogeneous catalyst comprising Keggin type polyoxometalate, silicotungstic acid (SiW₁₂), and MCM-22 was synthesized using wet impregnation method and characterized by acidity measurement, BET, FT-IR, XRD, and SEM. Their catalytic activity was evaluated for the degradation of cationic organic dyes like methylene blue (MB), crystal violet (CV), and an azo dye Chryosidine Y (CY) in an aqueous solution. The experimental parameters such as catalyst amount, initial dye concentration, and contact time were studied for the degradation of dyes, and it was found that the cationic dyes like methylene blue and crystal violet show better activity as compared to azo dye Chryosidine Y. This may be attributed to better electrostatic interaction of these cationic dyes with the residual negative surface charge of the catalyst, due to presence of SiW₁₂ ion as it is rich in surface oxygens and surface hydroxyl groups. The control experimental results showed that the presence of SiW₁₂ at the surface of MCM-22 promoted the degradation reactions, and presence of multiple W–O bonds in polyoxometalate also played a key role in this reaction. The catalyst exhibits recycling ability without any significant loss in activity up to four cycles.

     

硅烷化改性MCM-41负载戊二酸锌催化CO2与环氧丙烷共聚制备可降解材料

以三甲基氯硅烷(TMCS)为硅烷化试剂,对MCM-41分子筛进行表面改性处理,并以此为载体制备负载型戊二酸锌催化剂(ZnGA/TMCS-MCM-41);采用红外光谱、氮气吸附-脱附和X射线衍射等分析手段对催化剂进行表征,结果表明:三甲基氯硅烷基团被成功接枝到MCM-41分子筛表面,形成比表面积略低的硅烷化MCM-41载体,但其骨架未被破坏,负载活性物质过程中,戊二酸锌能以更小的粒径均匀分散到载体的表面;聚合反应实验表明,与单纯戊二锌催化剂相比,ZnGA/TMCS-MCM-41催化剂对CO2与环氧丙烷(PO)的共聚反应显示出更高的催化效率和更快的反应速度,在反应34 h后催化效率达到86.3 g聚合物/g ZnGA;红外光谱和核磁分析表明所得共聚产物中碳酸酯结构含量大于95.8%。     

Decomposition of indoor ammonia with TiO2-loaded cotton woven fabrics prepared by different textile finishing methods

Addition of urea-based antifreeze admixtures during cement mixing in construction of buildings has led to increasing indoor air pollution due to continuous transformation and emission of urea to gaseous ammonia in indoor concrete wall. In order to control ammonia pollution from indoor concrete wall, the aqueous dispersion was firstly prepared with nano-scale TiO₂ photocatalysts and dispersing agent, and then mixed with some textile additives to establish a treating bath or coating paste. Cotton woven fabrics were used as the support materials owing to their large surface area and large number of hydrophilic groups on their cellulose molecules and finished using padding and coating methods, respectively. Two TiO₂-loaded fabrics were obtained and characterized by X-ray diffractometer (XRD) and scanning electron microscopy (SEM). Moreover, a specifically designed ammonia photocatalytic system consisting of a small environmental chamber and a reactor was used for assessing the performance of these TiO₂-loaded fabrics as the wall cloth or curtains used in house rooms in the future and some factors affecting ammonia decomposition are discussed. Furthermore, a design equation of surface catalytic kinetics was developed for describing the decomposition of ammonia in air stream. The results indicated that increasing dosage of the TiO₂ aqueous dispersion in treating bath or coating paste improved the ammonia decomposition. And ammonia was effectively removed at low ammonia concentration or gas flow rate. When relative humidity level was 45%, ammonia decomposition was remarkably enhanced. It is the fact that ammonia could be significantly decomposed in the presence of the TiO₂-padded cotton fabric. Whereas, the TiO₂-coated cotton fabric had the reduced photocatalytic decomposition of ammonia and high adsorption to ammonia owing to their acrylic binder layer. Finally, the reaction rate constant k and the adsorption equilibrium constant K values were determined through a curve-fitting method and the TiO₂-padded cotton fabric had the higher k value and lower K value than the TiO₂-coated cotton fabric.     

Physical and chemical regeneration of zeolitic adsorbents for dye removal in wastewater treatment

Natural zeolite and synthetic zeolite, MCM-22, were employed as effective adsorbents for a basic dye, methylene blue, removal from wastewater. Two methods, Fenton oxidation and high temperature combustion, have been used for regeneration of used materials. It is found that MCM-22 exhibits equilibrium adsorption at 1.7 x 10(-4) mol g(-1), much higher than the adsorption of natural zeolite (5 x 10(-5) mol g(-1)) at initial dye concentration of 2.7 x 10(-5)M and 30 degrees C. Solution pH will affect the adsorption behaviour of MCM-22. Higher solution pH results in higher adsorption capacity. The regenerated adsorbents show different capacity depending on regeneration technique. Physical regeneration by high temperature combustion will be better than chemical regeneration using Fenton oxidation in producing effective adsorbents. Regeneration of MCM-22 by high temperature treatment can make the adsorbent exhibit comparable or superior adsorption capacity as compared to the fresh sample depending on the temperature and time. The optimal temperature and time will be 540 degrees C and 1h. The Fenton oxidation will recover 60% adsorption capacity. For natural zeolite, regeneration can not fully recover the adsorption capacity with the two techniques and the regenerated natural zeolites by the two techniques are similar, showing 60% adsorption capacity of fresh sample. Kinetic studies indicate that the adsorption follows pseudo-second-order kinetics.     

Synthesis of Fe-doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst and its sonophotocatalytic activity on synthetic dye and real textile wastewater

The catalysts such as Fe, Bi₂O₃, and Fe-doped Bi₂O₃ were synthesized for the sonophotocatalytic treatment of synthetic dye and real textile wastewater. The resultant catalysts were characterized for its size and uniform shape using x-ray diffractogram (XRD) and scanning electron microscopy (SEM) which signified the nanorod shape formed Bi₂O₃. The higher ultraviolet light absorbance capacity of the catalysts was also evident using diffuse reflectance spectroscopy (DRS). Initially, the effect of conventional parameters such as initial pH, gas bubbling (argon, oxygen, air and nitrogen) and oxidant addition (H₂O₂ and peroxymonosulfate) in the presence of sonolysis (22 and 37 kHz frequency) and photolysis (UV-C light) on 10 ppm Basic Brown 1 dye was studied. The results showed that highest decolorization of 62 % was attained for 3 g/L peroxymonosulfate under 37 kHz frequency sonolysis treatment. Secondly, with the catalyst study, highest of 46 % dye color removal was obtained with 4 g/L Fe under 37 kHz frequency sonolysis treatment. The sonophotocatalytic treatment of dye with Fe-doped Bi₂O₃ catalyst in combination with peroxymonosulfate showed highest color removal of 99 %. Finally, the sonophotocatalytic treatment of real textile wastewater in the presence of 3 g/L Fe-doped Bi₂O₃ and 6 g/L peroxymonosulfate reduced the total organic carbon (TOC) and chemical oxygen demand (COD) level to 77 and 91 %, respectively, in 180 min. The reported treatment process was found to treat the synthetic dye and real textile wastewater effectively.     

A laboratory study of microalgae-based ammonia gas mitigation with potential application for improving air quality in animal production operations

Ammonia gas emission is a major concern in concentrated animal production operations. It not only reduces the manure value as fertilizer due to nitrogen loss, but also has considerable environmental consequences for both animals and ecosystem. In this work, a microalgae culture system was developed as an ammonia gas bioscrubber to reduce ammonia gas emission. The green algae Scenedesmus dimorphus was grown in a flat-panel photobioreactor aerated with ammonia-laden air. A continuous culture was performed at different operational conditions including dilution rate (D = 0.05, 0.1, 0.2, and 0.3 day^?1), ammonia gas loading rate (9.4, 19.3, 28.9, 39.9, 55.6 mg/L-day), and medium pH (5, 6, 7, and 8). The alga culture at 0.1 day^?1 dilution rate, 39.9 mg/L-day ammonia gas loading rate, and pH 7 resulted in the highest cell density and biomass productivity. In order to provide a wide spectrum evaluation of the algae-based ammonia mitigation system, four parameters were determined, including ammonia removal rate, overall ammonia gas removal efficiency, cellular ammonia consumption rate, and cell yield based on ammonia input. Depending on the operational conditions used, the maximum values of those four evaluative parameters were 50.92 ± 2.91 mg/L-day of ammonia removal rate, 94.90 ± 1.87% of ammonia removal efficiency, 0.0597 ± 0.0024 g NH₃/g cell-day of cellular ammonia consumption rate, and 19.40 ± 2.52 g cell/g NH₃ of cell yield based on ammonia. It was also found that the majority of nitrogen in the ammonia gas was assimilated by the algal cells. At D = 0.1 day^?1, 39.9 mg/L-day of ammonia gas loading rate and pH 7, algal biomass assimilated 98.6% of nitrogen contained in the ammonia gas input, with less than 5% of inlet ammonia gas was exhausted after the algal treatment.

Implications: This study demonstrated the effectiveness of using microalgae for mitigating ammonia gas emission from animal production operations. The results enabled us to better understand the mechanisms of ammonia assimilation by microalgae, the engineering design parameters for the process scale up, and the economic viability of the system. Eventually, it will lead to a novel, alternative method for mitigating ammonia gas emission from concentrated animal operations while producing biomass as high-quality feed ingredient.     

超声波协同H_2O_2处理养殖场污水

为了有效地改善养猪场污水的质量,以H2O2为药剂,对污水进行了水浴加热和超声波辅助的对比实验,考察了超声波发生器输出端电流强度、处理时间、H2O2用量对污水的COD、氨气及颜色的影响,并进行正交实验优化。结果表明,超声波协同H2O2处理养殖污水是一种切实可行的方法,超声波协同H2O2处理污水的最佳工艺条件:电流0.7 A、处理时间2 min、H2O2用量3%,在此条件下降低COD量可达95%以上,氨氮的含量可降至14~15 mg/L,氨臭味大大得到了改善,并将原污水由黑色变为浅黄色。     

Gas reforming and tar decomposition performance of nickel oxide (NiO)/SBA-15 catalyst in gasification of woody biomass

In the gasification of biomass, it is necessary to limit the amount of by-product tar and increase the yields of hydrogen (H₂) and carbon monoxide (CO) (syngas). Therefore, we conducted gasification and reforming experiments on woody biomass using an electric tubular furnace, to evaluate the gas reforming and tar decomposition performance of a NiO/SBA-15 catalyst. As a result, we found that this catalyst is effective for H₂ production. It is believed that the increase in H₂ volume due to the catalyst occurs through a steam reforming reaction involving hydrocarbons, including methane (CH₄), and the water-gas shift reaction. With respect to the influence of the gasifying agent on the reforming effect of the catalyst, the amount of generated carbon dioxide (CO₂) and hydrogen (H₂) increases because the shift reaction is promoted by supplying steam. On the other hand, it was inferred that the shift reaction rarely occurred because it approaches equilibrium by supplying O₂. Furthermore, it is suggested that light aromatic hydrocarbons are decomposed by the catalyst.

Implications: The mesoporous silica catalyst NiO/SBA-15 was highly effective for H₂ production and decomposition of light aromatic compounds in the gasification of woody biomass. In the catalyst reaction, supplying steam promoted H₂ production. From thermodynamic analysis and discussion, it was also inferred that supplying O₂ might prevent the water gas shift reaction. The results are useful for designing a process needed for rich H₂ production and gas refining process for further use of syngas.     

Fenton氧化活性深蓝染料B-2GLN的动力学

为了考查H2O2/Fe2+的摩尔比和H2O2的初始剂量、pH值以及活性深蓝染料B-2GLN(RDB B-2GLN)的初始浓度对活性深蓝染料B-2GLN降解过程的影响,采用在线分光光度法对活性深蓝染料B-2GLN的Fenton氧化过程进行了研究,探讨了其动力学过程,并利用气相色谱-质谱联用分析降解中间产物。结果显示,采用Fenton氧化降解水溶液中活性深蓝染料B-2GLN,在H2O2的剂量为2.635 mmol/L,pH值为2.7,H2O2/Fe2+的摩尔比为37.80和活性深蓝染料B-2GLN的初始浓度16 mg/L的条件下,得到300 s后活性深蓝染料B-2GLN的最大色度去除率为85.04%。水溶液中活性深蓝染料B-2GLN与·OH的反应速率常数为2.62×1011L/(mol·s)。活性深蓝B-2GLN染料的分子结构被Fenton试剂分解而未被完全矿化,同时对活性深蓝染料降解产物进行了分析。在线分光光度法是研究染料色度去除率的一种精确、快速与可行的方法。     

Evaluation of new surfactant expanded zirconium and titanium phosphates for polycyclic aromatic hydrocarbons extraction from waters

A newly synthesized family of materials prepared with surfactant as organic template were tested for the extraction of polycyclic aromatic hydrocarbons (PAHs) from water, using pyrene (Pyr) and benzo[a]pyrene (B[a]P) as PAHs representatives. Particular attention was paid to the evaluation of the recovery factors with dichloromethane as eluent in order to estimate their potential as adsorbing solid phases for PAH remediation or analysis. Eleven lamellar MCM-50 type materials incorporating n-alkyl- (n = 12, 16, 18) trimethylammonium bromide molecules with different concentrations and chain lengths and two hexagonal MCM-41 type materials incorporating octadecyl-trimethyl ammonium bromide were tested. Best results were obtained by preparing lamellar MCM-50 zirconium and titanium phosphates in the presence of n-dodecyl-trimethylammonium at a relative molar concentration (surfactant/phosphate) of 1.