Assessment of plastic packaging waste: Material origin,methods, properties

The global plastics production has increased annually and a substantial part is used for packaging (in Europe 39%). Most plastic packages are discarded after a relatively short service life and the resulting plastic packaging waste is subsequently landfilled, incinerated or recycled. Laws of several European and Asian countries require that plastic packaging waste collected from households has to be sorted, reprocessed, compounded and reused. These recycling schemes typically produce milled goods of poly(ethylene terephthalate) (PET), poly(ethylene) (PE), isotactic poly(propylene) (PP), mixed plastics, and agglomerates from film material. The present study documents the composition and properties of post-consumer polyolefin recyclates originating from both source separation and mechanical recovery from municipal solid refuse waste (MSRW). The overall composition by Fourier transform-infrared (FT-IR) spectroscopy and differential scanning calorimetry (DSC) were determined and compared with the sorting results of the sorted fractions prior to the reprocessing into milled goods. This study shows that the collection method for the plastic packaging waste has hardly any influence on the final quality of the recyclate; however, the sorting and reprocessing steps influence the final quality of the recyclate. Although the mechanical properties of recyclate are clearly different than those of virgin polymers, changes to the sorting and reprocessing steps can improve the quality.     

Determining long-term (decadal) deep drainage rate using multiple tracers

The deep drainage rate is a critical hydrological parameter in understanding contamination mechanisms of soil and groundwater. Little research has been conducted on the temporal variations in deep drainage rate during the last century. The objective of this study was to determine the long-term deep drainage rate on a cultivated loamy soil in the Canadian Prairies. Three tracers were used: KCl applied in 1971, fallout tritium in 1963, and NO3* released during the initial cultivation of the field (1923). Two soil cores to a depth of 3.6 m were taken along a flat portion of the field, and soil Cl(-), 3H, and NO3* concentrations were measured as a function of depth. An additional four cores were taken for soil water content measurements between 2000 and 2003. Distinct peaks in the depth distribution of these three tracers were located at 1.27 m for Cl(-), 1.31 m for 3H, and 1.52 m for NO3*, 32, 40, and 80 yr after the application of Cl(-), 3H, and NO3*, respectively. The average deep drainage rates, calculated as the product of the estimated tracer velocity and volumetric soil water content below the active root zone, were 2.0 mm yr(-1) from the Cl(-) tracer, 2.2 mm yr(-1) from 3H, and 2.5 mm yr(-1) from the NO3* tracer. Therefore, there was little temporal variability in the groundwater recharge over the eight decades that the field has been cultivated. The recharge rates are less than 1% of the mean annual precipitation (333 mm).     

Sourcing sediment using multiple tracers in the catchment of Lake Argyle,Northwestern Australia

Control of sedimentation in large reservoirs requires soil conservation at the catchment scale. In large, heterogeneous catchments, soil conservation planning needs to be based on sound information, and set within the framework of a sediment budget to ensure that all of the potentially significant sources and sinks are considered. The major sources of sediment reaching the reservoir, Lake Argyle, in tropical northwestern Australia, have been determined by combining measured sediment fluxes in rivers with spatial tracer-based estimates of proportional contributions from tributaries of the main stream entering the lake, the Ord River. The spatial tracers used are mineral particle magnetics, the strontium isotopic ratio, and the neodymium isotopic ratio. Fallout of ¹³⁷Cs has been used to estimate the proportion of the sediment in Lake Argyle eroded from surface soils by sheet and rill erosion, and, by difference, the proportion eroded from subsurface soils by gully and channel erosion. About 96% of the sediment in the reservoir has come from less than 10% of the catchment, in the area of highly erodible soils formed on Cambrian-age sedimentary rocks. About 80% of the sediment in the reservoir has come from gully and channel erosion. A major catchment revegetation program, designed to slow sedimentation in the reservoir, appears to have had little effect because it did not target gullies, the major source of sediment. Had knowledge of the sediment budget been available before the revegetation program was designed, an entirely different approach would have been taken.     

Selective flotation separation of plastics by chemical conditioning with methyl cellulose

The floatability of seven plastics (POM, PVC, PET, PMMA, PC, PS and ABS) in the presence of methyl cellulose (MC) and separation of plastics mixtures were investigated in this paper. It was found that the seven plastics can be separated into three groups by using the wetting agent MC. Group one includes POM and PVC. They are depressed at very low MC concentrations. Group two, including PET, PMMA and PC, has an intermediate floatability. Group three (ABS and PS) has a high floatability. They are almost not depressed within the given MC concentration range. In order to understand the mechanism of selective flotation of plastics and the chemical conditioning process, surface chemical factors, such as wettability of plastics and surface tension of flotation medium, and gravity factors, such as particle density and shape, were studied. It was found that the depressing effect of MC on plastics is ascribed mainly to its adsorption on the plastics surfaces. The MC molecules absorbed on plastics expose some of their polar groups oriented towards the aqueous phase, hence making the plastics surfaces hydrophilic. In addition, flotation selectivity for the plastics is dominated not only by wettability of plastics, but also by particle size, density and shape.     

铁泥塑料特性及其制品的开发应用

铁泥塑料是利用硫酸厂、磷肥厂的弃渣－铁泥（代号FM）和废旧聚烯烃等为主要原料,以独特的技术和先进工艺制成的新型矿物增强塑料,已获国家发明专利CN1039496,铁泥塑料具有良好的物理机械性能,耐光、耐寒和抗老化特性,且无臭无毒,加工性能好,价格低廉,具有广阔实用开发前景。本文着重介绍铁泥塑料的理化特性,及其制品的开发应用,为在我国西部大开发中,抛砖引玉。     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

Sound management of brominated flame retarded (BFR) plastics from electronic wastes: State of the art and options in Nigeria

Management of flame retarded plastics from waste electrical and electronic equipment (WEEE) has been posing a major challenge to waste management experts because of the potential environmental contamination issues especially the formation of polybrominated-dioxins and -furans (PBDD/F) during processing. In Nigeria, large quantities of electronic waste (e-waste) are currently being managed—a significant quantity of which is imported illegally as secondhand electronics. As much as 75% of these illegal imports are never reused but are rather discarded. These waste electronic devices are mostly older equipment that contains brominated flame retardants (BFRs) such as penta-brominated diphenyl ethers (PBDEs), and polybrominated biphenyls (PBBs) which are presently banned in Europe under the EU WEEE and RoHS Directives. Risk assessment studies found both to be persistent, bio-accumulative and toxic. The present management practices for waste plastics from WEEE in Nigeria, such as open burning and disposal at open dumps, creates potential for serious environmental pollution. This paper reviews the options in the environmentally sound management of waste plastics from electronic wastes. Options available include mechanical recycling, reprocessing into chemicals (chemical feedstock recycling) and energy recovery. The Creasolv^® and Centrevap^® processes, which are the outcome of the extensive research at achieving sound management of waste plastics from WEEE in Europe, are also reviewed. These are solvent-based methods of removing BFRs and they presently offer the best commercial and environmental option in the sound management of waste BFR-containing plastics. Because these developments have not been commercialized, WEEE and WEEE plastics are still being exported to developing countries. The industrial application of these processes and the development of eco-friendlier alternative flame retardants will help assure sound management of WEEE plastics.     

Analysis of products from the pyrolysis and liquefaction of single plastics and waste plastic mixtures

Waste plastics in the form of two examples of real world municipal solid waste plastics and a simulated mixture of municipal waste plastics were pyrolysed and liquefied under moderate temperature and pressure in a batch autoclave reactor. In addition, the five main polymers which constitute the majority of plastics occurring in European municipal solid waste comprising, polyethylene, polypropylene, polystyrene, polyethylene terephthalate and polyvinyl chloride were also reacted. The plastics were reacted under both a nitrogen (pyrolysis) and hydrogen pressure (liquefaction) and the yield and composition of products are reported. The hydrocarbon gases produced were mainly methane, ethane, propane and lower concentrations of alkene gases. A mainly oil product was produced with the mixed plastic waste with significant concentrations of aromatic compounds, including single ring aromatic compounds. The composition of the oils and gases suggested that there was significant interaction of the plastics when they were pyrolysed and liquefied as a mixture compared to the results expected from reactions of the single plastics.     

Assessing drilling mud and technical fluid contamination in rock core and brine samples intended for microbiological monitoring at the CO2 storage site in Ketzin using fluorescent dye tracers

The CO₂SINK project in Ketzin represents a field laboratory for the storage of CO₂ in a 650-m deep saline aquifer. The project is accompanied by a microbiological monitoring programme to characterise the composition and activity of the autochthonous microbial community in rock and brine samples and their changes in response to CO₂ storage. A prerequisite of these studies is the acquisition of samples free of contamination from microorganisms and organic and inorganic components. Drilling mud and technical fluids are the main sources of contamination. This study describes the application of the fluorescent dye tracers fluorescein and rhodamine B as contamination controls for rock core and brine samples. Fluorescein was added to drilling mud that was used during the coring phase of the Ketzin wells Ktzi 200, 201 and 202. In addition, total organic carbon (TOC) concentrations, reflecting the carboxymethyl cellulose (CMC) component of the drilling mud, were determined to verify the tracer results. The fluorescence and TOC analyses revealed that drilling mud filtrate penetrated the outer 20 mm of mildly permeable sandstone cores. Rhodamine B was added to brines that were used to displace the drilling mud and to flush the wells after completion. The tracer monitoring during the discharge of drilling mud and displacement brines from the wells during hydraulic tests and nitrogen lifts enabled the quantification of reservoir fluid quality. After the production of 140–190 m³ (16–21 borehole volumes) of fluid, the drilling mud concentration was reduced to about 0.05%. The use of fluorescein emerged as a field-capable, sensitive and reliable method during the sampling of rock core and formation brine samples.     

镁合金在笔记本电脑外壳材料替代中的环境协调性评价

本文应用生命周期评价，（life cycle assessment，LCA）方法，对镁合金以及塑料这两种笔记本电脑外壳进行了初步评价和比较，结果表明镁舍金能源消耗、温室效应方面为塑料的556．31％、383．30%。但在材料的性能、资源消耗、酸化效应、生态毒理、材料的再生性等方面明显优于塑料。     

基于工艺过程分析的废旧塑料再生利用污染源研究

在分析废旧塑料再生利用工艺过程的基础上,确定了废塑料综合利用工艺的产污节点,并通过物流平衡和水平衡计算,得出了总的产排污量,为环境保护措施提供重要依据,以实现保护环境和资源合理再生利用。     

Households’ recycling efforts

Households’ recycling effort is often argued to be of an insignificant size. It is also frequently argued that this contribution, if significant, is not a cost to households, since it is voluntary. Thus households’ use of time and energy are frequently disregarded in cost-benefit analyses of stricter recycling targets. In this survey, based on 1162 interviews, we find that sorting at source involves significant extra use of time and energy in the households. On average, each of those asked reported that they use close to half an hour a week for cleaning, sorting and transporting recyclable waste. On average, 185 h is used per tonne of waste. Four out of ten reported that they use warm or hot water to clean the materials. When investigating the motives for sorting waste, we find that many perceive sorting as mandatory, while some in fact find it a pleasant activity in itself. Moral motives for sorting at source are also widespread. A majority would prefer that a company took over the sorting if this were possible, and on average, the respondents are willing to pay US$ 20/year for this service.     

Incorporation of neural network analysis into a technique for automatically sorting lightweight metal scrap generated by ELV shredder facilities

In an attempt to improve the technique of automatic sorting of lightweight metal scrap by sensing apparent density and three-dimensional shape, realized by the combination of a three-dimensional (3D) imaging camera and a meter to weigh a moving object on a conveyor belt, neural network analysis was integrated into the scrap identification algorithm, and its effect on the sorting accuracy of this technique was examined using approximately 1750 pieces of scrap sampled at three different end-of-life vehicle (ELV) shredder facilities. As a result, the newly developed algorithm, in which an unknown fragment is identified by passing through two discriminant analyses and one neural network analysis, was demonstrated to greatly decrease the time required for data analysis to prepare the identification algorithm without reducing the sorting accuracy. The average sorting accuracy for a mixture of three types of lightweight metal fragments was found to be 85%, based on the fact that the fist-sized fragments of cast aluminum, wrought aluminum, and magnesium sampled at the three ELV shredder facilities had similar apparent densities and 3D shapes. It was also suggested that still higher sorting performance is possible by repeating the procedure of modifying the database and re-learning of the neural network in the identification algorithm.     

2010年上海世博会垃圾组分的预测

为了便于2010年上海世博会期间生活垃圾的处理与处置，选择了和世博园区垃圾性质相近似的南京路步行街为参照区，进行垃圾组分的调研，预测模拟世博园区垃圾的组成与性质。研究结果表明：南京路步行街垃圾中食物垃圾占50％左右，塑料和纸张占45％左右，而一般的城市生活垃圾中塑料和纸张只占20％～30％左右，可见对于类似的垃圾资源化程度非常高。因此对于世博园垃圾进行分选，实现各组分垃圾的分流，可以更好地实现垃圾的资源化、减量化。     

Backwater Confluences of the Ohio River: Organic and Inorganic Fingerprints Explain Sediment Dynamics in Wetlands and Marinas

In the Ohio River (OR), backwater confluence sedimentation dynamics are understudied, however, these river features are expected to be influential on the system’s ecological and economic function when integrated along the river’s length. In the following paper, we test the efficacy of organic and inorganic tracers for sediment fingerprinting in backwater confluences; we use fingerprinting results to evidence sediment dynamics controlling deposition patterns in confluences used for wetland and marina functions; and we quantify the spatial extent of tributary drainages with wetland and marina features in OR confluences. Both organic and inorganic tracers statistically differentiate sediment from stream and river end‐members. Carbon and nitrogen stable isotopes produce greater uncertainty in fingerprinting results than inorganic elemental tracers. Uncertainty analysis of the nonconservative tracer term in the organic matter fingerprinting application estimates an apparent enrichment of the carbon stable isotopes during instream residence, and the nonconservativeness is quantified with a statistical approach unique to the fingerprinting literature. Wetland and marina features in OR confluences impact 42% and 11% of tributary drainage areas, respectively. Sediment dynamics show wetland and marina confluences experience deposition from river backwaters with longitudinally linear and nonlinear patterns, respectively, from sediment sources.     

膨胀型阻燃聚丙烯材料的耐湿热性能研究

聚丙烯(PP)以其优异的力学性能、密度小、质量轻等特点而广泛用于汽车、家电、建筑等行业.但是聚丙烯容易燃烧,其氧指数只有18左右,且燃烧时还会产生大量熔滴,极易传播火焰,这大大限制了其应用.近年来,膨胀型阻燃剂(IFR)在阻燃PP中的应用受到了人们高度的重视.本文主要介绍膨胀型阻燃剂微胶囊制备及其微胶囊在聚丙烯中阻燃性...     

Mechanical separation-oriented characterization of electronic scrap

The ever-increasing amount of electronic scrap and the steadily-decreasing contents of the precious metals used in electronics, as well as the ever-growing environmental awareness, challenges such conventional precious-metal-oriented recycling techniques as pyrometallurgy. Separation and beneficiation of various materials encountered in electronic scrap might provide a correct solution ahead. In this context, mechanical separation-oriented characterization of electronic scrap was conducted in an attempt to evaluate the amenability of mechanical separation processes. Liberation degrees of various metals from the non-metals, which are crucial for mechanical separation, were analyzed by means of a grain counting approach. It is found that the metallic particles below 2 mm achieve almost complete liberation. Particle shapes were also quantified through an image processing system. The results obtained show that the shapes of the particles, as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, separability of various materials was ascertained by a sink–float analysis. It has been shown that density-based separation techniques shall be viable in separating metals from plastics, light plastics (ABS, PS and PVC, etc.) from glass fiber reinforced resins and aluminum from heavy metals. Specifically, a high quality copper concentrate can be expected by density-based separation techniques. Moreover, FT-IR spectra of plastics pieces from the light fractions after the sink–float testing show that PC scrap primarily contains ABS, PS and PVC plastics with the density range of +1.0–1.5 g/cm³, whereas PCB scrap mainly contains glass fiber reinforced epoxy resins plastics with the density range of +1.5–2.0 g/cm³.     

Public participation in plastics recycling schemes

Without public contributions, recycling from domestic waste would not be possible. In order to support recycling projects it is important to try to understand who recycles, how they recycle, and why they recycle. This paper presents the results of a structured survey of 500 members of the public served by schemes to collect plastics waste for recycling. Data were gathered on the characteristics, behaviours and motivations of recyclers. The authors also sought to discover how the public perceive plastics compared to other materials, and as a recyclable material. Responses were collected in such a way that the awareness of the recyclability of materials could be compared with the recycling behaviour of respondents. An element of comparison was introduced between those served by a system of bottle banks (bring scheme) and those covered by a household collection (collect scheme). The survey results are reported and their implications for the management of post-consumer plastics waste collection schemes are discussed.     

Relative merits of polystyrene foam and paper in hot drink cups: Implications for packaging

An analysis of the overall relative merits of the use of uncoated paper vs molded polystyrene bead foam in single-use 8-oz cups is described here as a manageable example of the use of paper vs plastics in packaging. In raw material requirements the paper cup required about 2.5 times its finished weight of raw wood and about the same hydrocarbon fueling requirement as is needed for the polystyrene foam cup. To process the raw materials about six times as much steam, 13 times as much electric power, and twice as much cooling water are consumed to produce the paper cup as compared to the polystyrene foam cup. Emission rates to air are similar and to water are generally higher for the paper cup. Virtually all primary use factors favor polystyrene foam over paper. Once used both cup types may be recycled. Landfill disposal of the two items under dry conditions will occupy similar landfill volumes after compaction and will confer similarly slow to nonexistent decomposition to either option. Under wet conditions polystyrene foam will not readily degrade, but may help other materials to do so. Paper under wet conditions will biodegrade to produce methane, a significant greenhouse gas, biochemical oxygen demand to any leachate, and instability to the land surface during the process. Both materials can be incinerated cleanly in a municipal waste stream with the option of energy recovery, to yield an ash volume of 2%–5% of the incoming waste volume. Overall this analysis would suggest that polystyrene foam, with an extension to plastics in general, should be given more evenhanded consideration relative to paper in packaging applications than is currently the case.     

USE OF DYE TRACERS TO COLLECT HYDROLOGIC DATA IN OREGON1

Dye tracers have been used in Oregon in the Collection of hydrologic data on 2,350 miles of stream channels in the Long Tom, Umpqua, Willmette, and John Day River basins, and in the Carmen-Smith power tunnel. These investigations demonstrated the usefulness, of dye tracers for determining: (1) estimates of traveltimes and travel rates of water, (2) discharge where standard methods of measuring are not applicable, and (3) dispersion characteristics of streams. Illustrations are used to present the results of time-of-travel studies in simple, concise, and readily interpreted form.