混凝-化学沉淀法处理含氰废水的实验研究

采用“分步混凝 化学沉淀”法处理苯乙腈生产过程中排放的高浓度含氰废水 ,对混凝剂种类、用量、pH、搅拌速率等因素对总氰去除效果的影响进行了探讨 ,找到了此方法处理含亚铁氰化物废水的最佳工艺条件。在最佳工艺条件下处理废水 ,出水无色透明 ,总氰降到 1mg/L以下。该方法工艺简单 ,运行费用低 ,处理效果好 ,是一种具有推广价值的新方法     

混凝-化学沉淀法处理含氰废水的实验研究

采用“分步混凝-化学沉淀”法处理苯乙腈生产过程中排放的高浓度含氰废水，对混凝剂种类、用量、pH、搅拌速率等因素对总氰去除效果的影响进行了探讨，找到了此方法处理含亚铁氰化物废水的最佳工艺条件。在最佳工艺条件下处理废水，出水无色透明，总氰降到1mg／L以下。该方法工艺简单，运行费用低，处理效果好，是一种具有推广价值的新方法。     

二氧化氯处理矿山含氰废水的实验研究

实验采用二氧化氯 ( Cl O2 )作为矿山含氰废水处理剂 ,含氰废水在 p H 8.5～ 11.5之间 ,Cl O2 /CN- ≥ 3 (质量比 )的条件下 ,搅拌反应 3 0 min后 ,氰化物去除率达 99%以上 ,p H<9,CN- <0 .5 mg/L,达到《污水综合排放标准》中的一级标准。实验表明 ,利用 Cl O2 的强氧化性处理矿山含氰废水 ,具有投药量少、使用便捷、无二次污染等优点 ,且处理效果明显优于传统次氯酸盐处理法。     

ClO2对医院高浓度含氰废水处理的试验研究

以医院排放的高浓度含氰废水为研究对象,采用"硫酸亚铁+曝气"初级化学处理和ClO2二级深度氧化处理相结合的处理模式,不仅使含氰废水实现无毒化处理,而且使高浓度含氰废水实现资源化回收利用.试验表明,处理后的废水中CN-浓度达到国家排放标准GB8978-1996中的一级标准,为医院高浓度含氰废水的治理提供了一种新的方法.     

ClO2对医院高浓度含氰废水处理的试验研究

以医院排放的高浓度含氰废水为研究对象，采用“硫酸亚铁 曝气”初级化学处理和ClO2二级深度氧化处理相结合的处理模式，不仅使含氰废水实现无毒化处理，而且使高浓度含氰废水实现资源化回收利用。试验表明，处理后的废水中CN^-浓度达到国家排放标准GB8978-1996中的一级标准，为医院高浓度含氰废水的治理提供了一种新的方法。     

含氰废水氧化处理研究

本文对次氯酸盐(ClO~1)氧化法处理含氰废水的工艺条件和处理效果进行了研究。用此法处理电镀废水,CN~-去除率可达99.0％以上,处理后的废水含CN~-低于国家排放标准。对ClO~-—H_2O_2联合处理法也作了探讨。     

液体高铁酸钠同时去除电镀废水中氰化物和重金属

采用自制的电化学装置在线制备液体高铁酸钠,然后将制得的高铁酸钠投加到电镀废水中进行处理,考察不同pH值和不同高铁酸钠投加量对废水中总氰化物、Cu~(2+)、Ni~(2+)去除率的影响;对比研究了高铁酸钠氧化法和次氯酸钠氧化法在处理低浓度含氰电镀废水的效果。结果表明,当pH为9~10,高铁酸钠的最佳投加量为0.O.24±0.048 mmol·L~(-1)时,总氰化物、Cu~(2+)和Ni~(2+)的同时去除率均在90%以上;在处理低浓度含氰电镀废水时,高铁酸钠对总氰化物、Cu~(2+)和Ni~(2+)的同时去除率均明显高于次氯酸钠。这是因为高铁酸钠能够有效地氧化多种络合态的氰化物,包括Cu(CN)_4~(3-)、Cu(CN)_4~,Ni(CN)_4~(2-)等使废水中的重金属转变为离子态;然后在碱性条件下在高铁酸盐还原产物-Fe(OH)_3助凝和絮凝作用下,反应生成沉淀达到同时去除氰化物和重金属的目的。     

应用络合沉淀-化学氧化组合工艺处理高浓度含氰农药废水

由于氰化物的剧毒性以及农药废水的难生物降解性，含氰农药废水的治理难度较大。从工程应用的角度出发，在小试实验研究的基础上，确定了处理污染物含量高、难生物降解含氰农药废水的组合工艺流程为：FeSO₄络合沉淀→H₂O₂催化氧化→ClO₂深度氧化。组合工艺流程处理效果好，操作方便，出水水质稳定。研究结果表明，当FeSO₄加入量为理论计算值的1.3倍、3％H₂O₂和ClO₂投加量分别为24 mL/L和200 mg/L时，废水中CN^-离子的总去除率高达99.99％以上，COD总去除率达到99%。组合工艺不仅适用于处理高浓度含氰农药废水，而且也能为高浓度、难降解有机废水的治理提供有益的参考。     

二氧化氯处理矿山含氰废水的实验研究

实验采用二氧化氯(ClO2)作为矿山含氰废水处理剂,含氰废水在pH值8.5～11.5范围之间,ρ(ClO2/CN-)≥3的条件下,搅拌反应30 min后,氰化物去除率达99%以上,pH值＜9,ρ(CN)＜0.5 mg/L,达到<污水综合排放标准>中的一级标准.实验表明,利用二氧化氯的强氧化性处理矿山含氰废水,具有投药量少、使用便捷、无二次污染等优点,并且处理效果明显优于传统次氯酸盐处理法.     

SBR法降解高浓油脂废水的活性污泥菌驯化及小型连续处理

根据高浓度油脂废水生物降解处理采用酵母一级处理-SBR法二级处理的连续净化工艺的要求,使用规模为20 L的SBR反应器对城市生活污水处理用的活性污泥进行强制性驯化,并以驯化的活性污泥菌直接应用于SBR法处理含油废水.实验发现该小型SBR法的工艺技术方案可行,系统抗冲击负荷能力强,整个系统运行比较稳定,对于含高浓度油脂的油脂精练加工厂实际排放污水处理效果良好,油脂和COD的去除率分别连续稳定在95%和90%以上,出水水质指标达到国家一级排放标准的要求.     

电混凝处理电镀综合废水

采用电混凝法处理酸性电镀综合废水，首先研究了不同电流密度对总氰化物、重金属和化学需氧量（COD）去除率的影响。实验结果表明，电混凝可有效去除酸性电镀综合废水中的氰化物与重金属。随着电流密度的增大，总氰化物与重金属的去除率逐渐提高。当电流密度为10mA／cm2时，废水中残留的总氰化物、Cu2＋、Ni2＋、Cr6＋和Zn2＋ 的浓度分别为23．0、25．0、4．5、0．2和0．2mg／L。为了进一步提高去除率，在电化学体系中添加H2O2，随着H2O2投量的增大，总氰化物、重金属、COD去除率不断提高。当H2O2投量为3mL／L时，处理过废水中残留总氰化物、Cu2＋、Ni2＋、Cr6＋、Zn2＋和COD的浓度分别为0．2、2．0、3．0、1．5、0．1和220mg／L。     

Treatability of water-based paint wastewater with Fenton process in different reactor types

Water-based paint wastewater which is formed during the coating step of metal surfaces performed with various spray processes include binders, pigments and additives. Binders and other additives may also affect the toxicity of the paint depending on the specific characteristics of the paint. This study deals with Water-based paint wastewater, which is hard to treat. Fenton oxidation process was principally used to treat the wastewater. Treatability runs were carried out by using rust (oxidized iron) particles obtained as a waste of the metal rolling process, as the Fenton's catalyst. In order to change the variables such as dimensions of the column, packing material size, reactive dosage, pH value and reaction time, the experiments on the basis of packed columns and mixed reactors were carried out to increase the COD removal. COD eliminations with pH adjustment were about 20%. With the contribution of Fenton process in both column and mixed-reactor studies, the COD removal was improved by about 80%.     

炼焦废水生化处理技术研究进展

综述了近几年来炼焦废水及炼焦废水中主要成分(酚类、氨类物质、氰化物)的生化处理方法.其中废水中酚类物质的去除方法有投加有效菌、超滤法等;去除氨类物质的方法有A2/O法、纳滤法和反渗透法等;去除氰化物的方法有生物法和化学法等.综合处理炼焦废水的方法有双层生物膜法、生物脱氮法和含铁活性污泥处理技术等.     

Insights to false positive total cyanide measurements in wastewater plant effluents.

Many publicly owned treatment works in North America are exceeding permitted limits for total cyanide in their wastewater treatment effluents. A recently introduced rapid, segmented, flow-injection analysis procedure using UV digestion and amperometric detection of the membrane-separated cyanide was used to investigate the various scenarios by which elevated cyanide levels might be present in wastewater treatment plant effluent. A number of significant interferences can produce false positive bias during sample analysis with the traditional acid distillation technique, but are minimized or absent with the new analytical method. However, increased levels of cyanide were found in some chlorinated wastewaters compared to the levels before chlorination, suggesting a fast reaction mechanism associated with the disinfectant and some precursor in the wastewater. In particular, the contact of chlorine with nitrite in the presence of a carbon precursor appears to contribute to cyanide formation during wastewater treatment and sample handling. This paper explores the scenarios under which cyanide can form during wastewater treatment as well as those in which a false bias for total cyanide can be obtained during sample processing and provides guidance for appropriate sample handling, screening, and processing to ensure valid analytical results.     

Degradation of alachlor using an enhanced sono-Fenton process with efficient Fenton's reagent dosages

In this study, an enhanced sono-Fenton process for the degradation of alachlor is presented. At high ultrasonic power, low pH, and in the presence of adequate Fenton's reagent dosages, alachlor degradation can reach nearly 100%. The toxicity of treated alachlor wastewater, which was measured by changes in cell viability, slightly decreased after the Fenton or ultrasound/H₂O₂ process and significantly decreased after the enhanced sono-Fenton process. A satisfactory relationship was observed between the total organic carbon removal and cell viability increment, indicating that alachlor mineralization is a key step in reducing the toxicity of the solution. The formation of alachlor degradation byproducts was observed during the oxidation process, in which the first step was the substitution of a chloride by a hydroxyl group. In conclusion, the enhanced sono-Fenton process was effective in the degradation and detoxification of alachlor within a short reaction time. Thus, the treated wastewater can then be passed through a biological treatment unit for further treatment.     

新型活性炭固定化产品的制备及其处理焦化废水的特性

为解决优势菌种工程应用,研究不同固定化方法、载体和结构的固定化产品对焦化废水的降解特性。用活性炭粉末吸附菌种后,与聚乙烯醇和海藻酸钠混合制备了新型固定化球;用聚乙烯醇和海藻酸钠包埋吸附菌种的活性炭纤维毡,与立体弹性塑料填料连用,制备出3种不同形状的活性炭纤维膜片固定化产品复合填料。将游离菌和制备的4种活性炭固定化产品投入A/A/O工艺系统平行实验,考察处理焦化废水的效果。结果表明,活性炭纤维膜片固定化产品复合填料对焦化废水的降解能力优于其他固定化产品:缺氧池出水硝酸盐氮和亚硝酸盐氮浓度分别稳定在1.96 mg/L和0.49 mg/L,未产生氮的累积现象,COD去除率可达到60.92%。好氧池COD和氨氮降解效率分别为78.83%和85.52%,苯酚、氰化物降解效率均为97%以上。     

活性炭-臭氧体系处理含氰废水的作用机理

针对活性炭催化臭氧化降解低质量浓度含氰废水体系,研究了活性炭吸附、催化作用在催化臭氧化体系中的作用,提出了吸附-催化臭氧化协同作用机理。在活性炭-臭氧体系中,活性炭吸附CN-的能力很弱,活性炭在反应体系中主要起了吸附、催化臭氧的作用。活性炭-臭氧体系降解CN-的过程是臭氧直接氧化、活性炭吸附臭氧与活性炭催化臭氧产生.OH自由基间接氧化三者共同作用的结果。     

Microbial degradation of metal complexed cyanides and thiocyanate from mining wastewaters

A microbiological examination of the soil from a cyanide wastewater storage basin was carried out. The storage basin contained water from the cyanidation process of gold extraction, and it was composed principally of simple cyanide, metal complexed cyanide, mainly cuprocyanide, ferro-ferricyanides and thiocyanate. Pseudomonas species were the principal bacteria identified in the soil. Using the storage basin soil as a seed sludge, its potential for the biodegradation of all the cyanide complexes in the mining wastewater was studied in the laboratory, using batch, fed-batch and continuous processes. The ammonia and sulphate produced were quantified. The presence of intermediate products was suspected. In the continuous process, total degradation of all cyanide was observed at a dilution rate of 0.066 day(-1).