不同填充率对移动床生物膜反应器的产泥性能影响研究

研究了不同填充率下（10%～70%）移动床生物膜反应器的生物膜特征和处理效果，以及填充率与污泥产率的关系。结果表明：随着填充率的增加，填料上生物膜厚度逐渐减少，反应器中附着微生物浓度逐渐增加；污泥产率因填充率不同而有很大差异,同一个反应器内污泥产率随填充率的增加而减少；在进水COD为400 mg/L、NH⁺₄-N为40 mg/L、水力停留时间为12 h条件下，不同填充率下COD去除率均可达到94%以上，NH⁺₄-N去除率达到97%以上。     

炭纤维载体固定床厌氧发酵启动运行效果实验

以开发高效率、抗冲击性能强的高浓度有机废水沼气发酵技术为目的，用传统的 UASB反应器作为对照，研究了以炭纤维为生物膜载体的固定床厌氧反应器的启动运行效果。反应器进口废水 COD 为 5 000 mg/L, 水力停留时间 (HRT) 由213 h 逐步缩短为35 h，进水有机容积负荷(OLR)由0.56 kg COD/ (m³·d)提到3.45 kg COD/(m³·d)。结果表明，固定床反应器厌氧发酵的效率比对照高，出水 pH 值也比对照稳定；运行到第 50 d 时，固定床厌氧反应器和对照的 COD去除率分别由第 7 d 的36.56%和33.58%上升到87.9%和62.6%；固定床厌氧反应器的容积比产气率最高为1.16 m³/(m³·d)，累计产气量为415.59 L，而对照的容积比产气率最高值仅为0.31 m³ /(m³·d)，累计产气量为 71.66 L，前者最高容积比产气率和累计产气量分别是后者的3.74倍和5.78倍。固定床厌氧反应器的启动速度、COD 去除率和产甲烷效率显著地高于对照反应器。     

太阳光Fenton法处理垃圾渗滤液中有机污染物

研究利用太阳光Fenton法处理垃圾渗滤液。根据太阳光辐射强度随时间的变化规律，选择重庆7、8月份的晴天，在中午12：00到下午14：00时进行试验，研究太阳光辐射时间、pH值、Fenton试剂用量对垃圾渗滤液COD去除率的影响。研究结果表明：太阳光Fenton法对垃圾渗滤液的COD有较好的去除效果，COD去除率达86.2%。太阳光Fenton法处理垃圾渗滤液的优化条件是：日光辐射时间为120 min，pH值为2.5，Fe²⁺浓度为5 mmol/L，H₂O₂浓度为570 mmol/L。同时，论文还对太阳光Fenton法处理垃圾渗滤液的动力学进行分析。研究结果显示：太阳光Fenton法处理垃圾渗滤液，其表观动力学方程为-dC/dt=2.6×10^-8×P^1.92×F^1.79×E^1.67。     

不同pH值条件下Fe3+、Cu2＋和Zn2＋对厨余垃圾两相厌氧消化水解酸化过程的影响

通过间歇实验研究了在pH=7和不调节pH两种情况下添加不同浓度的Fe^3＋、Cu^2＋和Zn^2＋对厌氧消化水解酸化阶段有机酸组分和含量的影响。结果表明，pH=7时，添加50 mg/L Fe^3＋和30 mg/L Cu^2＋，有利于厨余垃圾水解酸化过程的进行，反应生成的VFA（挥发性脂肪酸）含量增加。不调节pH时，添加100 mg/L以下的Fe^3＋和Cu^2＋对VFA含量也有所促进，但乳酸含量也增加。在2种pH条件下添加Zn^2＋对反应的促进或抑制作用均不明显。     

改进型升流式固体反应器处理猪粪污新工艺研究

对传统升流式固体反应器（USR）进行改进，反应器内设置专用搅拌器，搅拌器间歇开启，在保留USR各项优势的前提下，使料液与厌氧微生物接触更充分，反应温度更均匀，提高产气率，同时还解决了传统USR的“结壳”问题，提高了反应器的传质效率、甲烷产气率和COD去除效果。进料含固量在12.1%时，水利停留时间为17 d，反应器最高容积负荷达到4.9 kg COD/(m³·d)，产气速率为2.55 m³/(m³·d)，产气率达到0.359 m³/kg干猪粪。     

A/O和A2/O工艺对膜生物反应器处理焦化废水影响的研究

为提高膜生物反应器对焦化废水的处理效果，采用A/O和A²/O两种工艺的膜生物反应器处理焦化废水，通过对比处理效果、分析膜污染情况，寻求膜生物反应处理焦化废水的最优工艺。实验结果表明：A²/O工艺系统对酚、NH₃-N、COD的去除率分别为99%、90%和95%；A/O工艺系统对酚、NH₃-N和COD的去除率分别为97%、75%和93%。A²/O膜生物反应器系统对焦化废水中NH₃-N的去除效果明显优于A/O膜生物反应器系统，其反硝化率为50%～70%。对膜污染分析表明不同工艺对膜污染的影响不显著，A²/O工艺膜通量衰减59%，A/O工艺膜通量衰减56%。研究表明在膜生物反应器中，A²/O工艺对焦化废水的去除效果要优于A/O工艺。     

印染废水水解酸化处理中填料式反应器与UASB反应器的比较

根据印染废水的特点和印染废水处理工程实例，从适用性、与其他工艺的衔接、工程造价、运行费用及水解效果等方面对UASB水解酸化反应器和填料式水解酸化反应器进行比较研究。研究表明，UASB水解酸化反应器在适用性和工程造价两个方面具有一定的缺陷；但是UASB水解酸化反应器对印染废水中COD、SS和色度去除率能够分别达到50％、73％和75％，明显高于填料式水解酸化反应器；且UASB水解酸化反应器每降解1kgCOD所需电量为（0．23±0．05）kW·h，优于填料式水解酸化反应器。     

污泥活性炭强化SBR法处理垃圾渗滤液的实验研究

为了进一步处理垃圾渗滤液，试验采用污泥活性炭强化序批式间歇反应器（SBR）法进行处理，通过对比普通SBR法试验，得出投加污泥活性炭强化SBR法处理垃圾渗滤液的效果要远远高于普通SBR法。当污泥活性炭的投加量为1.2 g/L，容积负荷为0.5～1.5 kg BOD₅/(m³·d)时，进水1 h，曝气10 h，沉淀1.5 h，闲置1.5 h，处理效果最好，COD的去除率达到了85%，NH³-N的去除率达到了90%。     

UASB反应器厌氧氨氧化菌的脱氮特性研究

研究UASB厌氧氨氧化（ANAMMOX）反应器运行情况，采用普通城市污水厂活性污泥接种，人工合成废水，pH值在7.4～7.8之间，温度控制在(32±1)℃。在反应器稳定运行270～450 d之间的180 d中，对NH⁺₄-N和NO^-₂-N去除率均达到99.9％以上，总氮去除率保持在90％以上，NO^-₃-N产生量在20～30 mg/L之间波动。研究表明,UASB厌氧氨氧化反应器处理废水效果明显，对NH⁺₄-N、NO^-₂-N和TN去除率高，NO^-₂-N和NH⁺₄-N比值可以指示厌氧氨氧化反应器性能的演变。UASB反应器稳定运行阶段容积负荷的影响较小，ANAMMOX菌对合成废水适应性强，反应器抗冲击能力较强，受冲击后恢复迅速。出水pH值稳定在8.5附近，pH值变化情况可作为反应器运行状况的指示。关键词硝化厌氧氨氧化上流式厌氧污泥床生物脱氮     

一体化A/O移动床生物膜反应器中DO、TN分布及脱氮效果研究

采用一体化A/O移动床生物膜法工艺，以模拟生活污水研究了该工艺的除碳脱氮效果，并对一体化移动床生物膜反应器的好氧区和缺氧区各纵向断面的COD、DO、NH₃-N、TN、NO^-₃-N和NO^-₂-N进行了检测，通过对缺氧区各断面的DO和TN浓度分布情况，分析了脱氮的产生过程。试验结果表明: 在水力停留时间HRT＝12 h，好氧区DO保持5 mg/L左右，COD进水浓度处于250～400 mg/L时，COD的去除率均在90%以上，且出水COD均在40 mg/L以下；TN进水浓度为20～50 mg/L时，NH₃-N去除率高于90%，其出水浓度可达到5 mg/L以下，脱氮效率也较高，TN去除率可达到65%～85%。COD和NH₃-N的浓度分布状况表明该一体化A/O移动床生物膜反应器的流态趋于全混式。     

Effect of alkalinity on the performance of a simulated landfill bioreactor digesting organic solid wastes

This study investigated the effects of alkalinity on the anaerobic treatment of the organic solid wastes collected from the kitchen of Engineering Faculty in Dokuz Eylul University, Izmir, Turkey and the leachate characteristics treated in three simulated landfill anaerobic bioreactors. All of the reactors were operated with leachate recirculation. One reactor was operated without alkalinity addition. The second reactor was operated by the addition of 3 g l-1 d-1 of NaHCO3 alkalinity to the leachate and the third reactor was operated by the addition of 6 g l-1 d-1 NaHCO3 alkalinity to the leachate. After 65 d of anaerobic incubation, it was observed that the chemical oxygen demand (COD), volatile fatty acids (VFA) concentrations, and biochemical oxygen demand to chemical oxygen demand (BOD5/COD) ratios in the leachate samples produced from the alkalinity added reactors were lower than the control reactor while the pH values were higher than the control reactor. The COD values were measured as 18900, 3800 and 2900 mg l-1 while the VFA concentrations were 6900, 1400 and 1290 mg l-1, respectively, in the leachate samples of the control, and reactors containing 3 g l-1 NaHCO3 and 6 g l-1 NaHCO3 after 65 d of anaerobic incubation. The total nitrogen (TN), total phosphorus (TP) and ammonium nitrogen (NH4-N) concentrations in organic solid waste (OSW) significantly reduced in the reactor containing 6 g l-1 NaHCO3 by d 65. The values of pH were 6.54, 7.19 and 7.31, after 65 d of anaerobic incubation, respectively, in the aforementioned reactors results in neutral environmental conditions in alkalinity added reactors. Methane percentage of the control, reactors containing 3 g l-1 NaHCO3 and 6 g l-1 NaHCO3 were 37%, 64% and 65%, respectively, after 65 d of incubation. BOD5/COD ratios of 0.27 and 0.25 were achieved in the 3 and 6 g l-1 NaHCO3 containing reactors, indicating a better OSW stabilization. Alkalinity addition reduced the waste quantity, the organic content of the solid waste and the biodegradation time.     

Effects of sludge recirculation rate and mixing time on performance of a prototype single-stage anaerobic digester for conversion of food wastes to biogas and energy recovery

Food wastes have been recognized as the largest waste stream and accounts for 39.25 % of total municipal solid waste in Thailand. Chulalongkorn University has participated in the program of in situ energy recovery from food wastes under the Ministry of Energy (MOE), Thailand. This research aims to develop a prototype single-stage anaerobic digestion system for biogas production and energy recovery from food wastes inside Chulalongkorn University. Here, the effects of sludge recirculation rate and mixing time were investigated as the main key parameters for the system design and operation. From the results obtained in this study, it was found that the sludge recirculation rate of 100 % and the mixing time of 60 min per day were the most suitable design parameters to achieve high efficiencies in terms of chemical oxygen demand (COD), total solids (TS), and total volatile solid (TVS) removal and also biogas production by this prototype anaerobic digester. The obtained biogas production was found to be 0.71 m³/kg COD and the composition of methane was 61.6 %. Moreover, the efficiencies of COD removal were as high as 82.9 % and TVS removal could reach 83.9 % at the optimal condition. Therefore, the developed prototype single-stage anaerobic digester can be highly promising for university canteen application to recover energy from food wastes via biogas production.     

含固率对牛粪常温厌氧消化的影响

在常温、pH值为7.0下,采用10 L玻璃瓶作为反应器对含固率(TS)分别为2%、6%、10%和14%的4组牛粪溶液进行厌氧消化实验,系统运行48 d,分析了厌氧消化过程中的COD(化学需氧量)、pH、VFA(挥发性脂肪酸)和产气量的变化。结果表明,进料TS是影响牛粪厌氧消化产气效果的重要因素,调节牛粪进料TS至10%,可以使其厌氧消化获得最佳的产气效果,COD去除率为24.6%,产气中甲烷含量为56.1%。     

Improved solubilization of activated sludge by ozonation in pressure cycles

The generation of a large volume of activated sludge (AS) from wastewater treatment has increasingly become a great burden on the environment. Anaerobic digestion is routinely practiced for excess waste sludge; however, the process retention time is long because of kinetic limitation in the hydrolysis step. We tested the feasibility of applying ozone in pressure cycles to enhance the disintegration and solubilization of AS with the goal to prepare them for digestion using reduced ozone dose and contact time. The AS was subjected to repetitive pressure cycles in a closed vessel in which an ozone gas mixture was compressed into the slurry to reach 1040 kPa in the headspace to be followed by rapid venting. For a returned AS with total COD (tCOD) of 8200 mg L(-1), a dose of 0.01 gO(3)g(-1) total suspended solids (TSS) delivered via 20 pressure cycles within 16 min resulted in a 37-fold increase of the sCOD/tCOD ratio (due to increased soluble COD, i.e. sCOD) and a 25% reduction of TSS, in comparison to a dose of 0.08 gO(3)g(-1) TSS via bubbling contact over 15 min that resulted in a 15-fold increase of the sCOD/tCOD ratio and a 12% reduction of TSS. Sludge solubilization was evidenced by increased dissolved contents of total phosphorous (from 10 to 64 mg L(-1)), total nitrogen (from 14 to 120 mg L(-1)), and protein (from <15 to 39 mg L(-1)) in the sludge suspension after treatment, indicating significant solubilization of AS.     

接种比对餐厨垃圾干式厌氧发酵启动的影响

针对不同接种比对餐厨垃圾干式厌氧发酵启动的影响,对比分析了VS接种比分别为0.36和0.90两种情况下,餐厨垃圾干式厌氧发酵启动过程中pH、NH4-N、COD、VFA、甲烷含量等指标的变化。实验结果表明,启动初期2组样品pH分别快速降至4.74和5.68,均呈酸化状态,经碱液调整后,接种比为0.36的处理仍无法正常产气,接种比为0.90的处理,pH逐步提高,系统正常运行,经72 d的发酵实验,COD去除率达90.29%,甲烷含量高于60%的沼气产量达255.4 L,分析可见,VS接种比是干式厌氧发酵处理的重要参数;此外,与传统湿式厌氧发酵处理相比,餐厨垃圾干式厌氧发酵在较高的VFA和氨氮浓度下,仍能正常运行,采用干式厌氧发酵技术处理餐厨垃圾是可行的。     

Effect of temperature and retention time on biomethanation of cheese whey-poultry waste-cattle dung

Various conditions, such as temperature, total solid content, cattle dung-poultry waste-cheese whey ratio, retention time and stirring, were optimized with an ultimate aim of improving anaerobic digestion. Maximum gas production (2.2 litres litre(-1) of digester day(-1)) with enriched methane content (62% CH(4)) was found with a retention time of 10 days, having a loading rate of 6.0 g total solid litre(-1) of digester day(-1) at 40 degrees C, and total solid of 6% (w/v) using a mixture of cattle dung, poultry waste and cheese whey in the ratio of 2:1:3 (w/w).     

稀盐酸预处理对稻草厌氧消化的影响

为探明稀酸预处理对稻草厌氧消化的影响,采用不同浓度的稀盐酸溶液对稻草进行了浸泡预处理,并在完全混合厌氧消化条件下,研究了稻草厌氧发酵过程中的产气量、甲烷含量,发酵液中COD、pH值及挥发性脂肪酸(VFA)的变化情况.结果表明,增大稀盐酸溶液浓度会提高稻草厌氧消化反应的效果.分别经4%、8%和12%的稀盐酸溶液浸泡预处理...     

青岛市餐厨垃圾与菜市场垃圾混合高温厌氧消化研究

在中试规模下,研究青岛市餐厨垃圾与菜市场垃圾混合(质量比1∶1)高温厌氧消化实验,通过监测厌氧消化过程中产气量、气体组成等产气情况和消化液中pH值、SCOD、NH3-H、VFAs含量和组分等化学指标变化,确定混合厌氧消化的最大有机负荷,并分析混合高温厌氧消化技术的可行性,结果表明,(1)青岛市餐厨垃圾与菜市场垃圾混合高温厌氧消化产甲烷具有技术可行性;(2)混合厌氧消化的最大有机负荷可达4.069 kg VS/(m3.d);(3)当系统最大有机负荷时,每天每千克VS最高可产生甲烷量0.346 m3;(4)混合厌氧消化可削减氨氮对餐厨垃圾单独厌氧消化产沼气的影响。     

Arsenic release from iron rich mineral processing waste: Influence of pH and redox potential

This paper presents the effect of pH and redox potential on the potential mobility of arsenic (As) from a contaminated mineral processing waste. The selected waste contained about 0.47 g kg(-1) of As and 66.2 g kg(-1) of iron (Fe). The characteristic of the waste was identified by acid digestion, X-ray diffraction and sequential extraction procedures. Less than 2% of the total As was acid extractable with the remaining 98% associated with Fe-oxyhydroxides and oxides. Batch leaching tests at different pH conditions showed a strong pH dependence on arsenic and iron leaching. Arsenic leaching followed a "V" shaped profiles with significant leaching in the acidic and alkaline pH region. Acid extractable phases dissolved at acidic pH, while desorption of arsenic due to increase in pH resulted in high arsenic concentration at alkaline pH. Under aerobic conditions and pH 7, As solubility was low, probably due to its precipitation on Fe-oxyhydroxides. Maximum As solubilization occurred at pH 11 (3.59 mg l(-1)). Similarity in the As and Fe leaching profiles suggested that the release of As was related to the dissolution of Fe in the low pH region. In general, redox potential did not play a significant role in arsenic or iron solubilization. It was thus concluded that for this solid waste, desorption was the predominant mechanism in arsenic leaching. A simple thermodynamic model based on arsenic and iron redox reactions was developed to identify the more sensitive redox couple.     

污泥加热预处理对中温厌氧消化的影响

对污泥加热预处理给中温厌氧混合消化和污泥单独消化带来的影响进行了研究.研究结果表明,污泥加热预处理有利于提高混合消化对 COD 的去除率,尤其是 SCOD 的去除率由 77%增长到 93%,但不利于 TS 和 VS 的去除;而对污泥单独消化,预处理则不利于有机物的去除.采用加热预处理后的污泥进样,混合消化和污泥单独消化的甲烷产气量均有所提高.