Effect of Decalin Solvent on the Thermal Degradation of HDPE

The thermal cracking of HDPE in presence of different amounts of decalin was studied and compared with the reaction carried out in the absence of solvent. The decalin favours the mass and heat transfer during the reaction. In addition, it modifies the thermal degradation mechanism, which facilitates the formation of specific products. The use of decalin substantially increases the C₅–C₃₂ yield in comparison with the solventless reaction. In all cases, linear hydrocarbons such as n-paraffins, α-olefins and α,ω-dienes were detected. Increasing the decalin/plastic ratio led to enhanced α-olefin and n-paraffins yields, but the increase was more significant in the case of α-olefins, which are valuable compounds useful as raw chemicals. A reaction mechanism was proposed to explain the results obtained in presence of decalin. In these reactions, intramolecular radical transfer, secondary radical β-scission and hydrogen transfer from both decalin to intermediate radicals and from the polymer chain to regenerate the decalin play a significant role in determining the plastic conversion and the relative amounts of each product.     

Resurrection of the iron and phosphorus resource in steel-making slag

 This research focused on the treatment of steel-making slags to recycle and recover iron and phosphorus. The carbothermal reduction behavior of both synthesized and factory steel-making slag in microwave irradiation was investigated. The slags were mixed with graphite powder and heated to a temperature higher than 1873 K to precipitate a lump of Fe–C alloy with a diameter of 2–8 mm. The larger the carbon equivalent (C_eq, defined in the text), the higher the fractional reduction of iron and phosphorus. An increase in the SiO₂ content of slag led to a considerable improvement in the reduction for both iron and phosphorus because of the improvement in the fluidity of the slags and an increase in the activity coefficient of P₂O₅ in the slags. The extraction behavior of phosphorus from Fe–P–C_satd alloy was also investigated at 1473 K by carbonate flux treatment. For all the experiments with a processing time longer than 10 min, the phosphorus in the fluxes could be concentrated to more than 9% (w/w) showing that it could be used as a phosphorus resource. Compared with K₂CO₃ flux treatment, that using Na₂CO₃ was more effective for the extraction of phosphorus, and this was attributed to the lower evaporation of Na₂CO₃. Finally, a recycling scheme for steel-making slag is proposed. Received: March 16, 2001 / Accepted: November 12, 2001     

Natural Weathering of Kenaf Bast Fibre-Filled Poly(Butylene Succinate) Composites: Effect of Fibre Loading and Compatibiliser Addition

Natural weathering was performed on poly(butylene succinate) (PBS) and its kenaf bast fibre (KBF) filled composites by exposing the specimens to a tropical climate for a period of 6 months (max–min temperature: 31.5–23.9 °C; relative humidity: 78.9%). The aim of this study was to investigate the effects of KBF loading and the addition of maleated PBS compatibiliser (PBSgMA) on the performance of the composites under natural weathering. As expected, the flexural properties of both the uncompatibilised and compatibilised composites dropped with increasing exposure time. The weathered specimens were also assessed by colour change analysis, FTIR spectroscopy analysis and SEM examination. The total colour change, ΔE _ab , of both the uncompatibilised and compatibilised composites increased with weathering time. FTIR spectroscopy analysis confirmed the presence of oxidation products such as hydroxyl, carbonyl and vinyl species in the weathered uncompatibilised and compatibilised composites. SEM examination revealed the presence of surface defects such as cracking, tiny holes and degraded fibre, which explain the poor performance of the composites upon weathering.     

Polyethylene conversion by partial oxidation in supercritical water

This paper gives the results of partial oxidation experiments of polyethylene (PE) in supercritical water (SCW). The experiments were carried out at a reaction temperature of 693K and a reaction time of 30 min using 6 cm³ of a batch-type reactor. The loaded sample weight was 0.3 g and there was 2.52 g water (0.42 g/cm³). The ratio of oxygen atoms to carbon atoms was 0.3. The results show a significant CO formation in O₂–SCW, and the 1-alkene/n-alkane ratio in partial oxidation was higher than that in SCW pyrolysis. These results suggest the possibility of the hydrogenation of hydrocarbon through partial oxidation followed by a water–gas shift reaction. Received: July 19, 2000 / Accepted: September 28, 2000     

Analysis of Products Generated from the Thermal and Catalytic Degradation of Pure and Waste Polyolefins using Py-GC/MS

The possibility of transforming waste plastics into valuable hydrocarbons via catalytic cracking and reforming is attracting increasing interest. Pyrolysis coupled with Gas Chromatographic separation and Mass Spectrometry detection (Py-GC/MS) has been used in this work to study the product selectivity of various catalysts in the conversion of pure and residual polyethylene samples into hydrocarbon products. Five acid solids of comparable aluminium contents but different textural and acid properties were tested as catalysts, including three zeolites (standard ZSM-5, nanocrystalline n-ZSM-5 and Beta) and two mesostructured solids (Al-MCM-41 and Al-SBA-15). Thermal cracking of the pure and residual polymers generated a similar range of products to each other, with a high proportion of linear paraffins and olefins of varying lengths. The presence of zeolitic materials resulted in complete elimination of heavy linear products, an increase in the light hydrocarbon fraction and a marked selectivity towards the formation of single-ring aromatic species, particularly benzene, toluene and xylene. Aromatic formation was particularly notable with the small crystal size n-ZSM-5 (aromatic selectivity up to 53.9%) and less marked in the case of standard ZSM-5 (up to 36.4%) and Beta zeolite (up to 35.0%). Mesostructured catalysts like Al-MCM-41 and Al-SBA-15 favoured the production of light C₂–C₅ hydrocarbons (up to 57.9%) while the formation of aromatic products was significantly lower than with zeolitic materials. The paper examines the extent and the causes for this product selectivity and discusses its connection with the acid and textural properties of each catalyst. It was also observed that, under the experimental conditions employed, the products generated were not significantly affected by the nature and origin of the polymers employed.     

Identification,Abundance and Origin of Aliphatic Hydrocarbons in the Fine Atmospheric Particulate Matter of Athens,Greece

The organic chemical composition of the fine fraction of atmospheric particulate matter in Athens has been studied, in order to establish emission sources. The results of the analyses of the aliphatic fraction indicate that all samples contain n-alkanes ranging from C₁₄ to C₃₂, with C₂₅, C₂₆, C₂₇ and C₂₉ being the more abundant congeners. Fossil fuels biomarkers such as extended tricyclic terpanes (hopanes, steranes) and isoprenoid hydrocarbons (pristane, phytane) were observed in our samples on a daily basis. Source reconciliation was conducted using molecular diagnostic ratios (such as the carbon preference index – CPI). The mean CPI value (1.84) indicates the mixed origin of the Athenian fine particles. The notable presence of an unresolved complex mixture or “hump” of hydrocarbons in our gas chromatograms is indicative of petrogenic hydrocarbon inputs. An approximate measure of this kind of contamination is the ratio of the concentrations of unresolved components to the resolved n-alkanes and other major compounds (U:R). The high U:R value of 25.25 further confirmed the major contribution of fossil fuels. Yet, the percent contribution of leaf wax n-alkanes (25.15%) indicated the parallel contribution of biogenic sources. This work supports the conclusion that vehicular emissions were the major source of aliphatic organic compounds with a smaller contribution of biogenic n-alkanes during the study period in Athens.     

Simple removal of dioxins by injecting combustion gas into water

A simple, low-cost method for suppression of dioxins/furans (hereinafter referred to as dioxins) is required because many middle- and, especially, small-scale incinerators have fallen into disuse or have been dismantled because of the high running and system costs of measures for the suppression of dioxins. Therefore, the purpose of the present study was to develop a simple removal method for dioxins from combustion gas and to evaluate the basic removal rate of dioxins. The removal method for suspended matter in a gas mixture (cold model) and dioxins in exhaust gases (hot model) has been investigated by means of gas injection into water, the mechanism of which is that the suspended matter in the gas gathers at the gas–liquid interface. In the cold model, the removal ratio of fine particles (R_P) by gas injection into water was reproduced well by the following equation: R_P (%) = 100 × {1−exp(−0.8 · S_S · t_C)}, where S_S (cm²/cm³) is the specific surface area of bubbles and t_C (s) is the residence time of bubbles in water. The removal ratio of fine particles increased as the product S_s · t_C increased. In a hot model using the exhaust gas from combustion experiments of polyvinyl chloride, the removal ratio of dioxins (R_D) by injecting the exhaust gas into water was estimated by the following equation: R_D (%) = 100 × {1−exp(−0.8 · S_S · t_C · C_D0 ^0.07)}, where C_D0 [ng/cm³ (at standard temperature and pressure)] is the dioxins concentration in the exhaust gas before injection into water. R_D depends greatly on the specific surface area of bubbles and the residence time of the bubbles in water, and only weakly on the dioxins concentration in the exhaust gas. Injection of the exhaust gas into water has been shown to be effective and was evaluated as a simple method for the removal of dioxins from exhaust gas.     

Multiple use of waste catalysts with and without regeneration for waste polymer cracking

Waste plastics contain a substantial number of valuable chemicals. The wastes from post-consumer as well as from industrial production can be recycled to valuable chemical feedstock, which can be used in refineries and/or petrochemical industries. This chemical recycling process is an ideal approach in recycling the waste for a better environment. Polymer cracking using a laboratory fluidised bed reactor concentrated on the used highly contaminated catalyst, E-Cat 2. Even though E-Cat 2 had low activity due to fewer acid sites, the products yielded were similar with amorphous ASA and were far better than thermal cracking. The high levels of heavy metals, namely nickel and vanadium, deposited during their lifetime as an FCC catalyst, did not greatly affect on the catalyst activity. It was also shown that E-Cat 2 could be used with and without regeneration. Although there was more deactivation when there was no regeneration step, the yield of gases (C₂-C₇) remained fairly constant. For the first time, these results indicate that “waste” FCC catalyst (E-Cat) is a good candidate for future feedstock recycling of polymer waste. The major benefits of using E-Cat are a low market price, the ability to tolerate reuse and regeneration capacity.     

Pyrrolidinium Imides: Promising Ionic Liquids for Direct Capture of Elemental Mercury from Flue Gas

A new approach to vapor phase elemental mercury capture has been explored; this approach exploits an ionic liquid coating layer to oxidize elemental mercury for subsequent immobilization by chelating ligands. The room temperature ionic liquid 1-butyl-1-methyl pyrrolidinium bis(trifluoromethane sulfonyl)imide (P₁₄) was selected for study based on its oxidation potential window, thermal stability, and low vapor pressure. Tests were also completed in which KMnO₄ was added to P₁₄ to form a new ionic liquid, P₁₄–KMnO₄, with a higher oxidation potential. In room-temperature bulk liquid phase capture experiments, 59% of the elemental mercury in the inlet gas was captured using P₁₄ alone; mercury capture using P₁₄–KMnO₄ was quantitative. P₁₄ and P₁₄–KMnO₄ coatings were successfully applied to mesoporous silica substrates and to silica substrates functionalized with mercury chelating ligands. The coating layers were found to be thermally stable up to 300°C. Fixed-bed tests of nonfunctionalized silica coated with P₁₄ showed an elemental mercury uptake of 2.7 mg/g adsorbent at 160°C; at the same temperature, functionalized silica coated with P₁₄–KMnO₄ showed an elemental mercury capacity of at least 7.2 mg/g adsorbent, several times higher than that of activated carbon. The empty bed gas residence time in these tests was 0.04 s. A chelating adsorbent incorporating P₁₄ in the coating layer, may be capable of simultaneous removal of elemental and oxidized mercury from coal combustion flue gases.     

Decomposition of mixed plastics consisting of polypropylene and polyethylene terephthalate into oils over titania/silica catalysts

The catalytic decomposition of mixed plastics consisting of polypropylene (PP) and polyethylene terephthalate (PET) has been investigated over titania/silica catalysts at 698 K. The yield of oil produced was about 70%, and the large amounts of C₁₈₊ hydrocarbons this contained was from the aromatics in PET. Gas was also produced, including C₃–C₅ hydrocarbons. The carbon-number fractions in the oil was influenced by the PET/(PP + PET) ratios and the catalyst weight. The titania/silica catalysts could be used repeatedly, and after they had been fouled, could be regenerated. From the Fourier Transform Infrared (FT–IR) spectroscopic data of adsorbed pyridine on the catalyst surface, most of the acid sites of the titania/silica catalysts were found to be Lewis sites where the hydride abstracted from PP pyrolysates react with PET pyrolysates to form oil and gas. Received: July 19, 2000 / Accepted: October 20, 2000     

Biodegradable Polyesters and Polyamides From Difunctionalized Lauric and Coconut Fatty Acids

In this work, a major fatty acid from coconut oil was used as starting material in preparing biodegradable polymers. Thus, polyesters and polyamides from varying proportions of monomers, hydroxy- and amino- derivatives of lauric acid were synthesized. Initially, the derivatives were prepared by regioselective chlorination of lauric acid, in the presence of ferrous ions in strong acid medium. Subsequent hydroxylation and amination procedures yielded the hydroxy- and amino- derivatives of lauric acid. These monomers were polymerized in a reaction tube by simple polycondensation method at 220–230 °C for 6–8 h without catalyst. Molecular weight determination using –COOH by end group titration and gel permeation chromatography (GPC) gave an average molar mass of 3,000–5,000 g mol⁻¹ with n = 15–25 monomer units. Thermal properties such as glass transition (T_g) and decomposition (T_d) temperatures were obtained using differential scanning calorimetry (DSC). The same processes of synthesis and determinations above were applied to coconut fatty acids, derived from saponification of coconut oil, and resulted to very similar conclusions. A quick biodegradation assay against fungus Aspergillus niger UPCC 4219 showed that the polymers prepared are more biodegradable than conventional plastics such as polypropylene, poly(ethyleneterepthalate) and poly(tetrafluoroethylene) but not as biodegradable as cellulosic (newsprint) paper.     

Heterogeneous Sulfate Formation on Dust Surface and Its Dependence on Mineralogy: Balloon-Borne Observations from Balloon-Borne Measurements in The Surface Atmosphere of Beijing, China

This study focuses on providing a direct insight into the process by which sulfate is formed on mineral dust surface in the actual atmosphere. Six sets of aerosol measurements were conducted in the outskirts of Beijing, China, in 2002–2003 using a tethered balloon. The mineralogy of individual dust particles, as well as its influence on the S (sulfur) loadings was investigated by SEM-EDX analysis of the directly collected particles. The mixed layer in the urban atmosphere was found to be quite low (500–600m), often appearing as a particle dense stagnant layer above the surface. It is suggested that mineral dust is a common and important fraction of the coarse particles in Beijing (35–68%), and that it is relatively enriched with Calcite (>28%). An exceptional amount of S was detected in the mineral particles, which can be explained neither by their original composition, nor by coagulation processes between the submicron sulfates and the dust. Heterogeneous uptake of gaseous SO₂, and its subsequent oxidation on dust was suggested as the main pathway that has actually taken place in the ambient environment. The mineral class found with the largest number of particles containing S was Calcite, followed by Dolomite, Clay, Amphibole etc., Feldspar, and Quartz. Among them, Calcite and Dolomite showed distinctly higher efficiency in collecting sulfate than the other types. A positive correlation was found with the number of S containing particles and the relative humidity. Calcite in particular, since almost all of its particles was found to contain S above 60% r.h. On the other hand, the active uptake of SO₂ by the carbonates was not suggested in the free troposphere downwind, and all the mineral classes exhibited similar S content. Relative humidity in the free troposphere was suggested as the key factor controlling the SO₂ uptake among the mineral types. In terms of sulfate loadings, the relationship was not linear, but rather increased exponentially as a function of relative humidity. The humidity-dependent uptake capacity of mineral types altogether showed an intermediate value of 0.07 gSO₄ ²⁻ g⁻¹ mineral at 30% r.h. and 0.40 gSO₄ ²⁻ g⁻¹ mineral at 80%, which is fairly consistent with laboratory experiments.     

Synthesis of hydrogarnet from molten slag and its hydrogen chloride fixation performance at high temperature

Hydrogarnet was synthesized hydrothermally below 200°C using molten slag obtained from municipal solid waste. For comparison, it was also synthesized using pure-phase CaO–Al₂O₃–SiO₂–H₂O, as reported previously. The structural and textural properties of this material were investigated using various analytical and spectroscopic techniques such as X-ray diffraction, X-ray fluorescence spectrometry, atomic absorption spectrometry (AAS), thermogravimetry/differential thermal analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The Cl⁻ fixation ability of hydrogarnet was investigated in the temperature range 500–800°C in a fixed-bed flow reactor using a HCl concentration (1000 p.p.m.v.) similar to that of incinerator exhaust gas. Under these experimental conditions, the hydrogarnet was capable of reducing the HCl gas level to less than 1 p.p.m.v. Analysis of the spent catalyst revealed that the hydrogarnet was being transformed into wadalite and CaCl₂ at high temperatures. The elution test for chromium ions in hydrogarnet obtained from slag was also used, and it was found that chromium ions were not eluted from hydrogarnet. Received: January 27, 2001 / Accepted: October 11, 2001     

Sulphate and Nitrate in Precipitation and Soil Water in Pine Forests in Latvia

The SO₄–S and NO₃–N concentrations and pH in bulk precipitation, throughfall, stemflow and soil water for the 1994–2004 period were studied in pine forests in Latvia (Rucava and Taurene Integrated Monitoring stations). The SO₄–S and NO₃–N concentrations decreased over the study period, simultaneously with a decrease of acidity in precipitation. The changes were more evident in the western part of Latvia, probably due to declining long-range air pollution from West Europe. The trend of decreasing sulphate concentrations and increasing pH in precipitation were not followed by respective changes in soil water. In the upper soil horizon sulphate ion concentrations and acidity increased in soil water. Over the observation period, nitrate concentrations also showed an increasing trend in soil water at Rucava and Taurene, but these changes were not statistically significant.     

Determination of nitrous oxide, methane, and ammonia emissions from a swine waste composting process

The amounts of harmful gas emissions from the process of composting swine waste were determined using an experimental composting apparatus. Forced aeration (19.2–96.1 l/m³/min) was carried out continuously, and exhaust gases were collected and analyzed periodically. With weekly turning and the addition of a bulking agent in order to decrease the moisture content and increase air permeability, the temperature of most of the contents rose to 70°C and composting was complete within 3–5 weeks. NH₃, CH₄, and N₂O emissions were high in the early stage of composting. About 10%–25% of the nitrogen in the raw material was lost as NH₃ gas during composting. The emission rate of NH₃ mainly depended on the aeration rate, so that as the aeration rate rose, the level of NH₃ emissions increased. The CH₄ and N₂O emissions could be kept lower with adequate treatment at more than 40 l/m³/min aeration. N₂O may be mainly the result of the denitrification of NO _x -N in the additional matured compost used as a composting accelerator. Received: September 11, 1998 / Accepted: November 8, 1999     

Characterization and Properties of Hydrophilic Cellulose Acetate Propionate Derivative

The chemical modification of Acrylamidomethyl Cellulose Acetate Propionate (AMCAP) was carried out by radical addition of acrylic acid. The structural modification was confirmed with the aid of FTIR, MS and NMR techniques. Thermal properties of hydrophilic cellulose derivative (AMCAP–H₂O₂) such as glass transition (T_g 153 °C) and thermal stability (372.7 °C) were determined by DSC and TGA techniques, respectively. These thermal properties confirmed the introduction of carboxylic groups into AMCAP structure, which causes an impact in their properties. The AMCAP–H₂O₂ shows minor contact angle compared to AMCAP, giving a more hydrophilic characteristic, due to acrylic acid addition into the side chains of AMCAP polymer.     

PM<Subscript>10</Subscript> and Ultrafine Particles Counts In-Vehicle and On-Road in the Athens Area

This work presents the first results of a study concerning on-road and in-vehicle exposure to particulate matter in the area of Athens. PM₁₀ concentration measurements were conducted by TSI DustTrak, while driving along routes with different characteristics of traffic density, during September 2003–March 2004. Concurrent measurements of the ultrafine particles (UFPs) number concentration were also conducted, by condensation particle counter during part of the days. Pedestrian exposure to PM₁₀ and UFPs was also studied through stationary measurements on the kerbside of selected roads on November 2003 and February 2004. A major avenue, a heavy-trafficked road across a children hospital and two central roads, one in a residential and one in a commercial area were selected for measurement. The results indicate that every day commuters are exposed to significant concentration levels. Higher exposures were observed in heavy-trafficked areas and during rush hours. Mean PM₁₀ in-vehicle and on-road concentrations ranged from 30–320 μg/m³ and 70–285 μg/m³, respectively. The ultrafine particles number concentrations were in the range of 5.0 × 10⁴–17.3 × 10⁴ particles/cm³ in-vehicle and 3.1 × 10⁴–7.3 × 10⁴ particles/cm³ on the kerbside of a central residential road. Both PM₁₀ and UFPs concentrations presented repeated short-term peak exposures. The results clearly point out the importance of the road microenvironment (in-vehicle and on kerbside) for population exposure in urban areas.     

Effects of Acid Rain on Competitive Releases of Cd, Cu, and Zn from Two Natural Soils and Two Contaminated Soils in Hunan, China

Leaching experiments of rebuilt soil columns with two simulated acid rain solutions (pH 4.6–3.8) were conducted for two natural soils and two artificial contaminated soils from Hunan, south-central China, to study effects of acid rain on competitive releases of soil Cd, Cu, and Zn. Distilled water was used in comparison. The results showed that the total releases were Zn>Cu>Cd for the natural soils and Cd>Zn≫Cu for the contaminated soils, which reflected sensitivity of these metals to acid rain. Leached with different acid rain, about 26–76% of external Cd and 11–68% external Zn were released, but more than 99% of external Cu was adsorbed by the soils, and therefore Cu had a different sorption and desorption pattern from Cd and Zn. Metal releases were obviously correlated with releases of TOC in the leachates, which could be described as an exponential equation. Compared with the natural soils, acid rain not only led to changes in total metal contents, but also in metal fraction distributions in the contaminated soils. More acidified soils had a lower sorption capacity to metals, mostly related to soil properties such as pH, organic matter, soil particles, adsorbed SO₄ ²⁻, exchangeable Al³⁺ and H⁺, and contents of Fe₂O₃ and Al₂O₃.     

Hydrogen-rich fuel gas production from refuse plastic fuel pyrolysis and steam gasification

In this study, experimental conditions were optimized to maximize the production of hydrogen gas from refuse plastic fuel (RPF) by pyrolysis and steam gasification processes conducted in a laboratory-scale reactor. We carried out gasification using 10-g RPF samples at different temperatures (700°-1000°C) with and without steam. The effect of the amount of steam (0–0.25 g/min) for RPF steam gasification was also studied. The effect of K₂CO₃ as a catalyst on these processes was also investigated. Experimental results showed that the hydrogen gas yield increased with temperature; with respect to the gas composition, the hydrogen content increased mainly at the expense of other gaseous compounds, which highlights the major extension of secondary cracking reactions in the gaseous fraction at higher temperatures.     

Effect of additives on dechlorination of PVC by mechanochemical treatment

Polyvinyl chloride (–CH₂–CHCl–) _n (PVC) was ground with a powdered inorganic material (CaO, CaCO₃, SiO₂, Al₂O₃, or slag) in a planetary ball mill under atmospheric conditions to investigate the effect of additions on its dechlorination. The grinding causes a dehydrochlorinating reaction, forming a mixture of partially dechlorinated PVC and inorganic chloride, depending on the grinding time. The dechlorination increases as the grinding progresses, and is improved with increasing amounts of additives. The most effective additive is a mixture of CaO, SiO₂, and Al₂O₃, which has the same constituent components as blast furnace slag. CaO, a mixture of CaO, SiO₂, and blast furnace slag, are also effective, but CaCO₃ is the least effective additive tired. Received: August 3, 2000 / Accepted: September 21, 2000