Electrocatalytic biofilm reactor for effective and energy-efficient azo dye degradation: the synergistic effect of MnOx/Ti flow-through anode and biofilm on the cathode

● MnO _x /Ti flow-through anode was coupled with the biofilm-attached cathode in ECBR. ● ECBR was able to enhance the azo dye removal and reduce the energy consumption. ● Mn^IV=O generated on the electrified MnO _x /Ti anode catalyzed the azo dye oxidation. ● Aerobic heterotrophic bacteria on the cathode degraded azo dye intermediate products. ● Biodegradation of intermediate products was stimulated under the electric field. Dyeing wastewater treatment remains a challenge. Although effective, the in-series process using electrochemical oxidation as the pre- or post-treatment of biodegradation is long. This study proposes a compact dual-chamber electrocatalytic biofilm reactor (ECBR) to complete azo dye decolorization and mineralization in a single unit via anodic oxidation on a MnO_x/Ti flow-through anode followed by cathodic biodegradation on carbon felts. Compared with the electrocatalytic reactor with a stainless-steel cathode (ECR-SS) and the biofilm reactor (BR), the ECBR increased the chemical oxygen demand (COD) removal efficiency by 24 % and 31 % (600 mg/L Acid Orange 7 as the feed, current of 6 mA), respectively. The COD removal efficiency of the ECBR was even higher than the sum of those of ECR-SS and BR. The ECBR also reduced the energy consumption (3.07 kWh/kg COD) by approximately half compared with ECR-SS. The advantages of the ECBR in azo dye removal were attributed to the synergistic effect of the MnO_x/Ti flow-through anode and cathodic biofilms. Catalyzed by Mn^IV=O generated on the MnO_x/Ti anode under a low applied current, azo dyes were oxidized and decolored. The intermediate products with improved biodegradability were further mineralized by the cathodic aerobic heterotrophic bacteria (non-electrochemically active) under the stimulation of the applied current. Taking advantage of the mutual interactions among the electricity, anode, and bacteria, this study provides a novel and compact process for the effective and energy-efficient treatment of azo dye wastewater.     

Homogeneous and heterogeneous photolysis of nitrate in the atmosphere: state of the science,current research needs,and future prospects

● Recent advances in the photolysis of nitrate/HNO₃ are reviewed. ● Mechanisms and key factors affecting the photolysis of nitrate/HNO₃ are summarized. ● Atmospheric implications and future research recommendations are provided. Nitrate is an important component of atmospheric particulate matter and affects air quality, climate, human health, and the ecosystem. Nitrate was previously considered a permanent sink for nitrogen oxides (NO_x). However, this viewpoint has been challenged in recent years because growing research evidence has shown the transformation of nitrate into NO_x (i.e., renoxification). The photolysis of nitrate/HNO₃, especially in the particulate phase or adsorbed on particles, can be a significant renoxification process in the atmosphere. The formation and photolysis of nitrate in aerosol not only change the diurnal variation of NO_x, but also provide long-distance transport of NO_x in the form of nitrate, which affects local and regional atmospheric chemistry and air quality. This review summarizes recent advances in the fundamental understanding of the photolysis of nitrate/HNO₃ under various atmospheric conditions, with a focus on mechanisms and key factors affecting the process. The atmospheric implications are discussed and future research is recommended.     

Mechanistic insights into the selective photocatalytic degradation of dyes over TiO2/ZSM-11

● TiO₂/ZSM-11 was prepared by a facile solid state dispersion method. ● Mechanism for photocatalytic degradation of dyes was investigated. ● Both experimental and MD simulations were conducted. ● Chemisorption instead of electrostatic interaction played a critical role. Photocatalytic degradation is a promising way to eliminate dye contaminants. In this work, a series of TiO₂/ZSM-11 (TZ) nanocomposites were prepared using a facile solid state dispersion method. Methyl orange (MO), methylene blue (MB), and rhodamine B (RhB) were intentionally chosen as target substrates in the photocatalytic degradation reactions. Compared to pristine TiO₂, negative effect was observed on MO degradation while promoted kinetics were collected on MB and RhB over TZ composites. Moreover, a much higher photocatalytic rate was interestingly achieved on RhB than MB, which indicated that a new factor has to be included other than the widely accepted electrostatic interaction mechanism to fully understand the selective photodegradation reactions. Systematic characterizations showed that TiO₂ and ZSM-11 physically mixed and maintained both the whole framework and local structure without chemical interaction. The different trends observed in surface area and the photo-absorption ability of TZ composites with reaction performance further excluded both as the promotion mechanism. Instead, adsorption energies predicted by molecular dynamics simulations suggested that differences in the adsorption strength played a critical role. This work provided a deep mechanistic understanding of the selective photocatalytic degradation of dyes reactions, which helps to rationally design highly efficient photocatalysts.     

Target the neglected VOCs emission from iron and steel industry in China for air quality improvement

● Haze formation in China is highly correlated with iron and steel industry. ● VOCs generated in sinter process were neglected under current emission standard. ● Co-elimination removal of sinter flue gas complex pollutants are timely needed. Recent years have witnessed significant improvement in China’s air quality. Strict environmental protection measures have led to significant decreases in sulfur dioxide (SO₂), nitrogen oxides (NO_x), and particulate matter (PM) emissions since 2013. But there is no denying that the air quality in 135 cities is inferior to reaching the Ambient Air Quality Standards (GB 3095–2012) in 2020. In terms of temporal, geographic, and historical aspects, we have analyzed the potential connections between China’s air quality and the iron and steel industry. The non-target volatile organic compounds (VOCs) emissions from iron and steel industry, especially from the iron ore sinter process, may be an underappreciated index imposing a negative effect on the surrounding areas of China. Therefore, we appeal the authorities to pay more attention on VOCs emission from the iron and steel industry and establish new environmental standards. And different iron steel flue gas pollutants will be eliminated concurrently with the promotion and application of new technology.     

Removal of ammonium and nitrate through Anammox and FeS-driven autotrophic denitrification

● Simultaneous NH₄⁺/NO₃^– removal was achieved in the FeS denitrification system ● Anammox coupled FeS denitrification was responsible for NH₄⁺/NO₃^– removal ● Sulfammox, Feammox and Anammox occurred for NH₄⁺ removal ● Thiobacillus, Nitrospira , and Ca. Kuenenia were key functional microorganisms An autotrophic denitrifying bioreactor with iron sulfide (FeS) as the electron donor was operated to remove ammonium (NH₄⁺) and nitrate (NO₃⁻) synergistically from wastewater for more than 298 d. The concentration of FeS greatly affected the removal of NH₄⁺/NO₃⁻. Additionally, a low hydraulic retention time worsened the removal efficiency of NH₄⁺/NO₃⁻. When the hydraulic retention time was 12 h, the optimal removal was achieved with NH₄⁺ and NO₃⁻ removal percentages both above 88%, and the corresponding nitrogen removal loading rates of NH₄⁺ and NO₃⁻ were 49.1 and 44.0 mg/(L·d), respectively. The removal of NH₄⁺ mainly occurred in the bottom section of the bioreactor through sulfate/ferric reducing anaerobic ammonium oxidation (Sulfammox/Feammox), nitrification, and anaerobic ammonium oxidation (Anammox) by functional microbes such as Nitrospira, Nitrosomonas, and Candidatus Kuenenia. Meanwhile, NO₃⁻ was mainly removed in the middle and upper sections of the bioreactor through autotrophic denitrification by Ferritrophicum, Thiobacillus, Rhodanobacter, and Pseudomonas, which possessed complete denitrification-related genes with high relative abundances.     

Ozonation of aromatic monomer compounds in water: factors determining reaction outcomes

● p- CNB and IBP were selected, to explore factors determining ozonation outcomes. ● •OH contributed only 50 % to IBP removal, compared to the 90 % for p -CNB removal. ● IBP achieved fewer TOC removal and more by-product types and quantities. ● A longer ring-opening distance existed during the degradation of IBP. ● Multiple positions on both branches of IBP were attacked, consuming more oxidants. For aromatic monomer compounds (AMCs), ozonation outcomes were usually predicted by the substituents of the benzene ring based on the electron inductive effect. However, the predicted results were occasionally unreliable for complex substituents, and other factors caused concern. In this study, p-chloronitrobenzene (p-CNB) and ibuprofen (IBP) were selected for ozonation. According to the electron inductive theory, p-CNB should be less oxidizable, but the opposite was true. The higher rates of p-CNB were due to various sources of assistance. First, the hydroxyl radical (•OH) contributed 90 % to p-CNB removal at pH 7.0, while its contribution to IBP removal was 50 %. Other contributions came from molecular O₃ oxidation. Second, p-CNB achieved 40 % of the total organic carbon (TOC) removal and fewer by-product types and quantities, when compared to the results for IBP. Third, the oxidation of p-CNB started with hydroxyl substitution reactions on the benzene ring; then, the ring opened. However, IBP was initially oxidized mainly on the butane branched chain, with a chain-shortening process occurring before the ring opened. Finally, the degradation pathway of p-CNB was single and consumed fewer oxidants. However, both branches of IBP were attacked simultaneously, and three degradation pathways that relied on more oxidants were proposed. All of these factors were determinants of the rapid removal of p-CNB.     

Methanation and chemolitrophic nitrogen removal by an anaerobic membrane bioreactor coupled partial nitrification and Anammox

● Efficient carbon methanation and nitrogen removal was achieved in AnMBR-PN/A system. ● AOB outcompeted NOB in PN section by limiting aeration and shortening SRT. ● The moderate residual organic matter of PN section triggered PD in anammox unit. ● AnAOB located at the bottom of UASB played an important role in nitrogen removal. An AnMBR-PN/A system was developed for mainstream sewage treatment. To verify the efficient methanation and subsequent chemolitrophic nitrogen removal, a long-term experiment and analysis of microbial activity were carried out. AnMBR performance was less affected by the change of hydraulic retention time (HRT), which could provide a stable influent for subsequent PN/A units. The COD removal efficiency of AnMBR was > 93% during the experiment, 85.5% of COD could be recovered in form of CH₄. With the HRT of PN/A being shortened from 10 to 6 h, nitrogen removal efficiency (NRE) of PN/A increased from 60.5% to 80.4%, but decreased to 68.8% when the HRT_PN/A further decreased to 4 h. Microbial analysis revealed that the highest specific ammonia oxidation activity (SAOA) and the ratio of SAOA to specific nitrate oxidation activity (SNOA) provide stable NO₂⁻-N/NH₄⁺-N for anammox, and anammox bacteria (mainly identified as Candidatus Brocadia) enriched at the bottom of Anammox-UASB might play an important role in nitrogen removal. In addition, the decrease of COD in Anammox-UASB indicated partial denitrification occurred, which jointly promoted nitrogen removal with anammox.     

Property-performance relationship of core-shell structured black TiO2 photocatalyst for environmental remediation

● Properties and performance relationship of CSBT photocatalyst were investigated. ● Properties of CSBT were controlled by simply manipulating glycerol content. ● Performance was linked to semiconducting and physicochemical properties. ● CSBT (W:G ratio 9:1) had better performance with lower energy consumption. ● Phenols were reduced by 48.30% at a cost of $2.4127 per unit volume of effluent. Understanding the relationship between the properties and performance of black titanium dioxide with core-shell structure (CSBT) for environmental remediation is crucial for improving its prospects in practical applications. In this study, CSBT was synthesized using a glycerol-assisted sol-gel approach. The effect of different water-to-glycerol ratios (W:G = 1:0, 9:1, 2:1, and 1:1) on the semiconducting and physicochemical properties of CSBT was investigated. The effectiveness of CSBT in removing phenolic compounds (PHCs) from real agro-industrial wastewater was studied. The CSBT synthesized with a W:G ratio of 9:1 has optimized properties for enhanced removal of PHCs. It has a distinct core-shell structure and an appropriate amount of Ti³⁺ cations (11.18%), which play a crucial role in enhancing the performance of CSBT. When exposed to visible light, the CSBT performed better: 48.30% of PHCs were removed after 180 min, compared to only 21.95% for TiO₂ without core-shell structure. The CSBT consumed only 45.5235 kWh/m³ of electrical energy per order of magnitude and cost $2.4127 per unit volume of treated agro-industrial wastewater. Under the conditions tested, the CSBT demonstrated exceptional stability and reusability. The CSBT showed promising results in the treatment of phenols-containing agro-industrial wastewater.     

Evaluating the impact of sulfamethoxazole on hydrogen production during dark anaerobic sludge fermentation

● SMX promotes hydrogen production from dark anaerobic sludge fermentation. ● SMX significantly enhances the hydrolysis and acidification processes. ● SMX suppresses the methanogenesis process in order to reduce hydrogen consumption. ● SMX enhances the relative abundance of hydrogen-VFAs producers. ● SMX brings possible environmental risks due to the enrichment of ARGs. The impact of antibiotics on the environmental protection and sludge treatment fields has been widely studied. The recovery of hydrogen from waste activated sludge (WAS) has become an issue of great interest. Nevertheless, few studies have focused on the impact of antibiotics present in WAS on hydrogen production during dark anaerobic fermentation. To explore the mechanisms, sulfamethoxazole (SMX) was chosen as a representative antibiotic to evaluate how SMX influenced hydrogen production during dark anaerobic fermentation of WAS. The results demonstrated SMX promoted hydrogen production. With increasing additions of SMX from 0 to 500 mg/kg TSS, the cumulative hydrogen production elevated from 8.07 ± 0.37 to 11.89 ± 0.19 mL/g VSS. A modified Gompertz model further verified that both the maximum potential of hydrogen production (P_m) and the maximum rate of hydrogen production (R_m) were promoted. SMX did not affected sludge solubilization, but promoted hydrolysis and acidification processes to produce more hydrogen. Moreover, the methanogenesis process was inhibited so that hydrogen consumption was reduced. Microbial community analysis further demonstrated that the introduction of SMX improved the abundance of hydrolysis bacteria and hydrogen-volatile fatty acids (VFAs) producers. SMX synergistically influenced hydrolysis, acidification and acetogenesis to facilitate the hydrogen production.     

Tailoring the simultaneous abatement of methanol and NOx on Sb-Ce-Zr catalysts via copper modification

● Cu addition enhances CH₃OH oxidation and alleviates its inhibitory effect on SCR. ● Cu addition improves the activation of SCR reactants in the presence of methanol. ● Damaged structure by more Cu addition decreases specific surface area and acidity. ● Excessive Cu addition would lead to the narrowing of SCR temperature window. Simultaneously removal of NO_x and VOCs over NH₃-SCR catalysts have attracted lots of attention recently. However, the presence of VOCs would have negative effect on deNO_x efficiency especially at low temperature. In this study, copper modification onto Sb_0.5CeZr₂O_x (SCZ) catalyst were performed to enhance the catalytic performance for simultaneous control of NO_x and methanol. It was obtained that copper addition could improve the low-temperature activity of both NO_x conversion and methanol oxidation, where the optimal catalyst (Cu_0.05SCZ) exhibited a deNO_x activity of 96% and a mineralization rate of 97% at 250 °C, which are around 10% higher than that of Cu free sample. The characterization results showed that copper addition could obviously enhance the redox capacity of the catalysts. As such, the inhibition effect of methanol incomplete oxidation on NO adsorption and NH₃ activation were then lessened and the conversion of surface formamide species were also accelerated, resulting in the rising of NO_x conversion at low temperature. However, excessive copper addition would damage the Sb-Ce-Zr oxides solid solution structure owing to Cu-Ce strong interactions, decreasing the surface area and acidity. Meanwhile, due to easier over-oxidation of NH₃ with more Cu addition, the temperature window for NO_x conversion would become quite narrow. These findings could provide useful guidelines for the synergistic removal of VOCs over SCR catalyst in real application.     

Low-temperature caproate production,microbial diversity,and metabolic pathway in xylose anaerobic fermentation

● Converting xylose to caproate under a low temperature of 20 °C by MCF was verified. ● Final concentration of caproate from xylose in a batch reactor reached 1.6 g/L. ● Changing the substrate to ethanol did not notably increase the caproate production. ● Four genera, including Bifidobacterium , were revealed as caproate producers. ● The FAB pathway and incomplete RBO pathway were revealed via metagenomic analysis. Mixed culture fermentation (MCF) is challenged by the unqualified activity of enriched bacteria and unwanted methane dissolution under low temperatures. In this work, caproate production from xylose was investigated by MCF at a low temperature (20 °C). The results showed that a 9 d long hydraulic retention time (HRT) in a continuously stirred tank reactor was necessary for caproate production (~0.3 g/L, equal to 0.6 g COD/L) from xylose (10 g/L). The caproate concentration in the batch mode was further increased to 1.6 g/L. However, changing the substrate to ethanol did not promote caproate production, resulting in ~1.0 g/L after 45 d of operation. Four genera, Bifidobacterium, Caproiciproducens, Actinomyces, and Clostridium_sensu_stricto_12, were identified as the enriched caproate-producing bacteria. The enzymes in the fatty acid biosynthesis (FAB) pathway for caproate production were identified via metagenomic analysis. The enzymes for the conversion of (C_n+2)-2,3-Dehydroxyacyl-CoA to (C_n+2)-Acyl-CoA (i.e., EC 1.3.1.8 and EC 1.3.1.38) in the reverse β-oxidation (RBO) pathway were not identified. These results could extend the understanding of low-temperature caproate production.     

A hybrid fuel cell for water purification and simultaneously electricity generation

● A novel hybrid fuel cell (F-HFC) was fabricated. ● Pollutant degradation and synchronous electricity generation occurred in F-HFC. ● BiOCl-NH₄PTA photocatalyst greatly improved electron transfer and charge separation. ● Pollutant could act as substrate directly in ambient conditions without pretreatment. ● The mechanism of the F-HFC was proposed and elucidated. The development of highly efficient energy conversion technologies to extract energy from wastewater is urgently needed, especially in facing of increasing energy and environment burdens. Here, we successfully fabricated a novel hybrid fuel cell with BiOCl-NH₄PTA as photocatalyst. The polyoxometalate (NH₄PTA) act as the acceptor of photoelectrons and could retard the recombination of photogenerated electrons and holes, which lead to superior photocatalytic degradation. By utilizing BiOCl-NH₄PTA as photocatalysts and Pt/C air-cathode, we successfully constructed an electron and mass transfer enhanced photocatalytic hybrid fuel cell with flow-through field (F-HFC). In this novel fuel cell, dyes and biomass could be directly degraded and stable power output could be obtained. About 87 % of dyes could be degraded in 30 min irradiation and nearly 100 % removed within 90 min. The current density could reach up to ~267.1 μA/cm²; with maximum power density (P_max) of ~16.2 μW/cm² with Rhodamine B as organic pollutant in F-HFC. The power densities were 9.0 μW/cm², 12.2 μW/cm², and 13.9 μW/cm² when using methyl orange (MO), glucose and starch as substrates, respectively. This hybrid fuel cell with BiOCl-NH₄PTA composite fulfills the purpose of decontamination of aqueous organic pollutants and synchronous electricity generation. Moreover, the novel design cell with separated photodegradation unit and the electricity generation unit could bring potential practical application in water purification and energy recovery from wastewater.     

The role of lipids in fermentative propionate production from the co-fermentation of lipid and food waste

● Lipid can promote PA production on a target from food waste. ● PA productivity reached 6.23 g/(L∙d) from co-fermentation of lipid and food waste. ● Lipid promoted the hydrolysis and utilization of protein in food waste. ● Prevotella , Veillonella and norank _f _Propioni bacteriaceae were enriched. ● Main pathway of PA production was the succinate pathway. Food waste (FW) is a promising renewable low-cost biomass substrate for enhancing the economic feasibility of fermentative propionate production. Although lipids, a common component of food waste, can be used as a carbon source to enhance the production of volatile fatty acids (VFAs) during co-fermentation, few studies have evaluated the potential for directional propionate production from the co-fermentation of lipids and FW. In this study, co-fermentation experiments were conducted using different combinations of lipids and FW for VFA production. The contributions of lipids and FW to propionate production, hydrolysis of substrates, and microbial composition during co-fermentation were evaluated. The results revealed that lipids shifted the fermentation type of FW from butyric to propionic acid fermentation. Based on the estimated propionate production kinetic parameters, the maximum propionate productivity increased significantly with an increase in lipid content, reaching 6.23 g propionate/(L∙d) at a lipid content of 50%. Propionate-producing bacteria Prevotella, Veillonella, and norank_f_Propionibacteriaceae were enriched in the presence of lipids, and the succinate pathway was identified as a prominent fermentation route for propionate production. Moreover, the Kyoto Encyclopedia of Genes and Genomes functional annotation revealed that the expression of functional genes associated with amino acid metabolism was enhanced by the presence of lipids. Collectively, these findings will contribute to gaining a better understanding of targeted propionate production from FW.     

Passive convergence-permeable reactive barrier (PC-PRB): An effective configuration to enhance hydraulic performance

● A novel PRB configuration based on passive convergent flow effect was proposed. ● A 2D finite-difference hydrodynamic model, PRB-Flow, was developed. ● PC-PRB can significantly enhance the hydraulic capture capacity of PRB. ● The PRB geometric dimensions and materials cost are effectively reduced. ● The dominant influential factor of the PC-PRB capture width is pipe length, L_p. A novel permeable reactive barrier (PRB) configuration, the so-called passive convergence-permeable reactive barrier (PC-PRB), is proposed to overcome several shortcomings of traditional PRB configurations, such as high dependency to site hydrogeological characteristics and plume size. The PC-PRB is designed to make the plume converge towards the PRB due to the passive hydraulic decompression-convergent flow effect. The corresponding passive groundwater convergence (PC) system is deployed upstream of the PRB system, which consists of passive wells, water pipes, and a buffer layer. A two-dimensional (2D) finite-difference hydrodynamic code, entitled PRB-Flow, is developed to examine the hydraulic performance parameters (i.e., capture width (W) and residence time (t)) of PC-PRB. It is proved that the horizontal 2D capture width (W_h) and vertical 2D capture depth (W_v) of the PC-PRB remarkably increase compared to that of the continuous reactive barrier (C-PRB). The aforementioned relative growth values in order are greater than 50% and 25% in this case study. Therefore, the PRB geometric dimensions as well as the materials cost required for the same plume treatment lessens. The sensitivity analysis reveals that the dominant factors influencing the hydraulic performance of the PC-PRB are the water pipe length (L_p), PRB length (L_PRB), passive well height (H_w), and PRB height (H_PRB). The discrepancy between the W_h of PC-PRB and that of the C-PRB (i.e., ΔW_h) has a low correlation with PRB parameters and mainly depends on L_p, which could dramatically simplify the PC-PRB design procedure. Generally, the proposed PC-PRB exhibits an effective PRB configuration to enhance hydraulic performance.     

Utilizing transparent and conductive SnO2 as electron mediator to enhance the photocatalytic performance of Z-scheme Si-SnO2-TiOx

• A novel Z-scheme Si-SnO₂-TiO_x with SnO₂ as electron mediator is first constructed. • Transparent and conductive SnO₂ can pass light through and promote charge transport. • V_O from SnO₂ and TiO_x improve photoelectrochemical performances. • Efficient photocatalytic degradations originate from the Z scheme construction. Z-scheme photocatalysts, with strong redox ability, have a great potential for pollutants degradation. However, it is challenging to construct efficient Z-scheme photocatalysts because of their poor interfacial charge separation. Herein, by employing transparent and conductive SnO₂ as electron mediator to pass light through and promote interfacial charge transportation, a novel Z-scheme photocatalyst Si-SnO₂-TiO_{x (1<x<2)} was constructed. The Z-scheme photocatalyst displayed an order of magnitude higher photocurrent density and a 4-fold increase in open-circuit potential compared to those of Si. Moreover, the onset potential shifted negatively for approximately 2.2 V. Benefiting from these advantages, this Z-scheme Si-SnO₂-TiO_x exhibited efficient photocatalytic performance toward phenol degradation and mineralization. 75% of the phenol was degraded without bias potential and 70% of the TOC was removed during phenol degradation. Other typical pollutants such as bisphenol A and atrazine could also be degraded without bias potential. Introducing a transparent and conductive electron mediator to construct Z-scheme photocatalyst gives a new sight to the improvement of photocatalytic performance in Z scheme.     

Cultivars and oil extraction techniques affect Cd/Pb contents and health risks in oil of rapeseed grown on Cd/Pb-contaminated farmland

● Organic solvent extracted fewer Cd/Pb in rapeseed oil than physical pressing. ● Brassica rapa transferred fewer Cd and Pb from seed to oil than Brassica napus . ● Carcinogenic risk mainly from Cd and worth more concern than noncarcinogenic risk. ● Organic solvent specially SLB pose less heath risk for oil than physical pressing. ● Rapeseed oil posed higher carcinogenic risk for rural residents than urban. Substitute planting with rapeseed offers promise for safely using large areas of Cd/Pb-contaminated farmland. Cd/Pb distributions during rapeseed oil production were investigated and health risks posed by the oil were assessed. Tests were performed using three cultivars (Brassica rapa SYH and ZS100 and Brassica napus QY-1) and four oil extraction techniques (mechanical and low-temperature pressing and n-hexane and subcritical low-temperature butane extraction). The amounts of Cd and Pb in oil were 0.73%–8.44% and 3.14%–11.76%, respectively, of the amounts in rapeseed and were strongly affected by the cultivar and oil extraction technique. The heavy metal (HM) concentrations were lower in solvent-extracted oil (particularly subcritical low-temperature butane extracted oil, in which HMs were not detected) than mechanically pressed oil. The Cd and Pb transfer indices were lower (meaning larger proportions of HMs were retained by the rapeseed meal) for B. rapa than B. napus. This was attributed to a high HM binding protein content of B. rapa seed. Health risks to humans were assessed using a probabilistic risk assessment model. The carcinogenic risk was mainly (97.1%–99.9%) caused by Cd and poses more concern than non-carcinogenic risk. Stronger health risks are posed by mechanically pressed than solvent-extracted oil, and higher carcinogenic risks are posed to people living in rural areas than urban areas. Substitute planting with B. rapa and extracting oil with organic solvent (preferably subcritical low-temperature butane) are optimal for safely utilizing Cd/Pb-contaminated soil. Attention should be paid to the health risks posed by Cd in oil to rural populations.     

PM2.5 concentration declining saves health expenditure in China

● Monthly hospitalization expenses are sensitive to increases in PM_2.5 exposure. ● The increased PM_2.5 causes patients with CHD and LRI to stay longer in the hospital. ● The impact of PM_2.5 on total expenses for stroke is greater in southern China. ● Males may be more sensitive to air pollution than females. Air pollution has been a severe issue in China. Exposure to PM_2.5 has adverse health effects and causes economic losses. This study investigated the economic impact of exposure to PM_2.5 pollution using monthly city-level data covering 88.5 million urban employees in 2016 and 2017. This study mainly focused on three expenditure indicators to measure the economic impact considering lower respiratory infections (LRIs), coronary heart disease (CHD), and stroke. The results show that a 10 µg/m³ increase in PM_2.5 would cause total monthly expenses of LRIs, CHD, and stroke to increase by 0.226%, 0.237%, and 0.374%, respectively. We also found that LRI, CHD, and stroke hospital admissions increased significantly by 10%, 8.42%, and 5.64%, respectively. Furthermore, the total hospital stays of LRIs, CHDs, and strokes increased by 2.49%, 2. 51%, and 1.64%, respectively. Our findings also suggest heterogeneous impacts of PM_2.5 exposures by sex and across regions, but no statistical evidence shows significant differences between the older and younger adult subgroups. Our results provide several policy implications for reducing unequal public health expenditures in overpolluted countries.     

Electro-conductive crosslinked polyaniline/carbon nanotube nanofiltration membrane for electro-enhanced removal of bisphenol A

● A crosslinked polyaniline/carbon nanotube NF membrane was fabricated. ● Electro-assistance enhanced the removal rate of the NF membrane for bisphenol A. ● Intermittent voltage-assistance can achieve nearly 100% removal of bisphenol A. ● Membrane adsorption–electro-oxidation process is feasible for micropollutant removal. Nanofiltration (NF) has attracted increasing attention for wastewater treatment and potable water purification. However, the high-efficiency removal of micropollutants by NF membranes is a critical challenge. Owing to the adsorption and subsequent diffusion, some weakly charged or uncharged micropollutants, such as bisphenol A (BPA), can pass through NF membranes, resulting in low removal rates. Herein, an effective strategy is proposed to enhance the BPA removal efficiency of a crosslinked polyaniline/carbon nanotube NF membrane by coupling the membrane with electro-assistance. The membrane exhibited a 31.9% removal rate for 5 mg/L BPA with a permeance of 6.8 L/(m²·h·bar), while the removal rate was significantly improved to 98.1% after applying a voltage of 2.0 V to the membrane. Furthermore, when BPA coexisted with humic acid, the membrane maintained 94% removal of total organic carbon and nearly 100% removal of BPA at 2.0 V over the entire filtration period. Compared to continuous voltage applied to the membrane, an intermittent voltage (2.0 V for 0.5 h with an interval of 3.5 h) could achieve comparable BPA removal efficiency, because of the combined effect of membrane adsorption and subsequent electrochemical oxidation. Density functional theory calculations and BPA oxidation process analyses suggested that BPA was adsorbed by two main interactions: π–π and hydrogen-bond interactions. The adsorbed BPA was further electro-degraded into small organic acids or mineralized to CO₂ and H₂O. This work demonstrates that NF membranes coupled with electro-assistance are feasible for improving the removal of weakly charged or uncharged micropollutants.     

Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

● A composite aerogel was simply obtained to remove various fluoroquinolones (FQs). ● The structural and textural properties of this composite aerogel are improved. ● Its adsorption capacity was improved at a low content of coexisting Cu²⁺ or Fe³⁺ ion. ● Two substructural analogs of FQs are compared to explore the adsorption mechanisms. ● This aerogel after saturated adsorption can be reused directly for Cu²⁺ adsorption. 3D composite aerogels (CMC-CG) composed of carboxymethyl cellulose and κ-carrageenan were designed and fabricated using the one-pot synthesis technique. The optimized CMC-CG showed a good mechanical property and a high swelling ratio due to its superior textural properties with a proper chemically cross-linked interpenetrating network structure. CMC-CG was utilized for the removal of various fluoroquinolones (FQs) from water and exhibited high adsorption performance because of effective electrostatic attraction and hydrogen bonding interactions. Ciprofloxacin (CIP), a popular FQ, was used as the representative. The optimized CMC-CG had a theoretically maximal CIP uptake of approximately 1.271 mmol/g at the pH of 5.0. The adsorption capacity of CMC-CG was improved in the presence of some cations, Cu²⁺ and Fe³⁺ ions, at a low concentration through the bridging effect but was reduced at a high concentration. The investigation of adsorption mechanisms, based on the adsorption kinetics, isotherms and thermodynamic study, Fourier transform infrared spectrometry and X-ray photoelectron spectroscopy analyses before and after adsorption, and changes in the adsorption performance of CMC-CG toward two molecular probes, further indicated that electrostatic attraction was the dominant interaction rather than hydrogen bonding in this adsorption. CMC-CG after saturated adsorption of CIP could be easily regenerated using a dilute NaCl aqueous solution and reused efficiently. Moreover, the disused aerogel could still be reused as a new adsorbent for effective adsorption of Cu²⁺ ion. Overall, this study suggested the promising applications of this composite aerogel as an eco-friendly, cost-effective, and recyclable adsorbent for the efficient removal of FQs from water.     

Contributions of adsorption,bioreduction and desorption to uranium immobilization by extracellular polymeric substances

● EPS immobilizes U(VI) via adsorption, bioreduction and desorption. ● This work provides a framework to quantify the three immobilization processes. ● The non-equilibrium adsorption of U follows pseudo-second-order kinetics. ● The equilibrium adsorption of U followed Langmuir and Freundlich isotherms. Hexavalent uranium (U(VI)) can be immobilized by various microbes. The role of extracellular polymeric substances (EPS) in U(VI) immobilization has not been quantified. This work provides a model framework to quantify the contributions of three processes involved in EPS-mediated U(VI) immobilization: adsorption, bioreduction and desorption. Loosely associated EPS was extracted from a pure bacterial strain, Klebsiella sp. J1, and then exposed to H₂ and O₂ (no bioreduction control) to immobilize U(VI) in batch experiments. U(VI) immobilization was faster when exposed to H₂ than O₂ and stabilized at 94% for H₂ and 85% for O₂, respectively. The non-equilibrium data from the H₂ experiments were best simulated by a kinetic model consisting of pseudo-second-order adsorption (k_a = 2.87 × 10⁻³ g EPS·(mg U)⁻¹·min⁻¹), first-order bioreduction (k_b = 0.112 min⁻¹) and first-order desorption (k_d = 7.00 × 10⁻³ min⁻¹) and fitted the experimental data with R² of 0.999. While adsorption was dominant in the first minute of the experiments with H₂, bioreduction was dominant from the second minute to the 50^th min. After 50 min, adsorption was negligible, and bioreduction was balanced by desorption. This work also provides the first set of equilibrium data for U(VI) adsorption by EPS alone. The equilibrium experiments with O₂ were well simulated by both the Langmuir isotherm and the Freundlich isotherm, suggesting multiple mechanisms involved in the interactions between U(VI) and EPS. The thermodynamic study indicated that the adsorption of U(VI) onto EPS was endothermic, spontaneous and favorable at higher temperatures.