Removal of anionic azo dye from aqueous solution via an adsorption–photosensitized regeneration process on a TiO2 surface

Textile dye effluents are typically characterized by strong color and recalcitrance, even at very low concentration. The process of enrichment of anionic azo dye on the surface of TiO₂ fibers followed by photosensitization degradation under ambient air conditions was extensively investigated. Adsorption isotherms and zeta potentials were used to describe the “dye/TiO₂ surface” interface, taking into account the effects of pH on the nature and population of the surface groups on the TiO₂ fibers. The extent of the photocatalytic degradation of dye on TiO₂ surface was determined by FTIR. N₂ adsorption isotherms and optical spectra were employed to investigate the effect of photosensitization. The adsorption of dyes on the TiO₂ surface occurs via electrostatic attraction through the formation of single- or multidentate-coordinated surface complexes. Almost complete photobleaching of the absorption band at 534 nm is achieved in ~4 h. Dye-sensitized TiO₂ fiber could absorb part of the visible light spectrum (λ?<?600 nm). Interfacial electron transfer can potentially alter the degradation efficiency. The regenerated TiO₂ fiber could be reused for subsequent decolorization without a decline in adsorption efficiency compared with freshly prepared TiO₂ samples, which may be attributed to preservation of the hierarchical pore structure and restoration of the original surface properties. In summary, we propose an efficient “adsorption–photoregeneration–reuse” process applying TiO₂ fibers for the degradation of dyes in water.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料，空心微珠为载体，采用溶胶凝胶法制备TiO₂/beads光催化剂载体，然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂，并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性，考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明，在中性条件下，H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L，浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

The influence of FeCl3 on the photocatalytic degradation of dissolved azo dyes in aqueous TiO2 suspensions

The study concerned decolouration of solutions of azo, anionic (Acid Orange 7, Reactive Red 45, Acid Yellow 23) and cationic (Basic Blue 41 and Basic Orange 66) dyes during illumination with UV (lambdamax 366 nm) irradiation in the presence of TiO2 and FeCl3. The process of decolouration during illumination of the solutions studied containing FeCl3 underwent significant intensification in the case of anionic dyes and unfavourable inhibition in case of cationic dyes. It was also observed that FeCl3 had a diverse influence on the adsorption of the dyes studied on TiO2. The adsorption of anionic dyes and decolouration of solutions before the illumination was observed only in the presence of FeCl3. In case of cationic dyes the addition of FeCl3 caused elimination of these phenomena. An additional cause of decolouration of anionic dyes solutions before illumination was the precipitation of their poorly soluble compounds from Fe3+. The processes of degradation and mineralization of the dye that accompanied decolouration of Acid Orange 7 solutions were also observed. It was stated that similarly to the case of Acid Orange 7, the decolouration of the studied anionic dyes' solutions can depend on the concentration of FeCl3, the amount of TiO2 and the initial concentration of the dye in its solution.     

Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

The objective of this study was to examine the effects of adsorbability and number of sulfonate group on solar photocatalytic degradation of mono azo methyl orange (MO) and diazo Reactive Green 19 (RG19) in single and binary dye solutions. The adsorption capacity of MO and RG19 onto the TiO₂ was 16.9 and 26.8 mg/g, respectively, in single dye solution, and reduced to 5.0 and 23.1 mg/g, respectively, in the binary dye solution. The data obtained for photocatalytic degradation of MO and RG19 in single and binary dye solution were well fitted with the Langmuir–Hinshelwood kinetic model. The pseudo-first-order rate constants of diazo RG19 were significant higher than the mono azo MO either in single or binary dye solutions. The higher number of sulfonate group in RG19 contributed to better adsorption capacity onto the surface of TiO₂ than MO indicating greater photocatalytic degradation rate.     

氯甲烷与偶氮染料混合废水的超声脱色

使用40 kHz超声(US)脱色氯甲烷(包括CCl4、CHCl3和CH2Cl2)与偶氮染料(包括甲基橙与铬黑T)混合模拟废水,考察了氯甲烷初始浓度对偶氮染料超声脱色和TOC去除的影响.结果表明:偶氮染料的单独超声脱色速率很慢;而在CCl4与CHCl3存在时超声能使偶氮染料短时间内脱色至无色,但对其TOC的超声去除促进作...     

催化臭氧氧化染料溶液的研究

采用催化臭氧化技术降解染料废水,以甲基紫溶液为目标污染物,研究了过渡型金属离子的类型,Fe2+的浓度,溶液初始pH值,染料浓度和正丁醇等因素对其降解率的影响。实验结果表明:臭氧氧化甲基紫溶液的过程中,加入一定浓度的过渡型金属离子对甲基紫的去除具有促进作用;当臭氧浓度为16 mg/L,一定浓度范围内,Fe2+催化臭氧化的效果随着浓度的增加而增加,但Fe2+浓度为13 mg/L时,甲基紫的降解率下降;在酸性范围时,pH值增大其降解率会减小;染料浓度增加,甲基紫的降解率减小,但是其绝对降解值会增加;正丁醇的加入抑制氧化反应的进行,甲基紫的降解率下降,说明催化臭氧化过程中有羟基自由基产生。染料降解过程符合一级反应动力学规律。     

Degrading a mixture of three textile dyes using photo-assisted electrochemical process with BDD anode and O2–diffusion cathode

In this paper, degradation of a mixture of three azo dyes was studied by the photo-assisted electrochemical process using an O₂-diffusion cathode containing carbon nanotubes and boron-doped diamond (BDD) anode. The concentration of three textile dyes (C.I. Acid Orange 8 (AO8), C.I. Acid Orange 10 (AO10), and C.I. Acid Orange 12 (AO12)) was determined simultaneously despite the severe overlap of their spectra. For this purpose, partial least square (PLS), as a multivariate calibration method, was utilized based on recording UV–Vis spectra during the decolorization process. Moreover, the central composite design was used for the modeling of photo-assisted electrochemical decolorization of the aqueous solutions containing three dyes. The investigated parameters were the initial concentration of three dyes, applied current and reaction time. Analysis of variance (ANOVA) revealed that the obtained regression models match the experimental results well with R (Khataee et al. 2010, Clean-Soil Air Water 38 (1):96–103, 2010) of 0.972, 0.971, and 0.957 for AO8, AO10, and AO12, respectively. Three-dimensional surface and contour plots were applied to describe the relation between experimental conditions and the observed response. The results of TOC analysis confirmed good ability of proposed photo-assisted electrochemical process for degradation and mineralization of textile industry wastewater.     

A comparative study of dye removal using fly ash treated by different methods

The effect of different methods for fly ash treatment using conventional chemical, sonochemical and microwave method on dye adsorption in aqueous solution was investigated. Three basic dyes, methylene blue, crystal violet and rhodamine B, are employed for adsorption testing. It is found that fly ash shows different adsorption capacity depending on type of dyes. Chemical treatment using HCl will increase the adsorption capacity. The adsorption capacity of HCl treated fly ash varies with the preparation conditions. Microwave treatment is a fast and efficient method while producing the sample with the highest adsorption capacity. Solution pH and inorganic salts in dye solution can significantly influence the adsorption. The adsorption data have been analysed using Langmuir, Freundlich and Redlich-Peterson isotherms. The results indicate that the Freundlich and Redlich-Peterson models provide the better correlations with the experimental data.     

双频超声辐射协同H2O2降解偶氮染料废水的研究

采用双频超声协同H₂O₂降解酸性绿20染料废水，考察超声功率密度、染料初始浓度和pH、饱和气体及H₂O₂投加量等因素对酸性绿20降解效果的影响，结果表明，在给定实验条件下，双频降解效果优于单频超声波，且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解，当染料废水初始pH=4可取得最佳的降解效果；酸性绿20的降解效率随染料初始浓度的增大而降低，其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H₂O₂，可取得最佳的降解效果。在优化实验条件下， 采用双频超声协同H₂O₂降解5 h，酸性绿20的色度和TOC去除率分别为94.6%和36.3%；分析降解前后的紫外可见光谱图可知，酸性绿20并非完全被降解为CO₂和H₂O，而是生成一些小分子有机中间体。     

A simple method to prepare magnetic modified beer yeast and its application for cationic dye adsorption

The purpose of this research is to use a simple method to prepare magnetic modified biomass with good adsorption performances for cationic ions. The magnetic modified biomass was prepared by two steps: (1) preparation of pyromellitic dianhydride (PMDA) modified biomass in N, N-dimethylacetamide solution and (2) preparation of magnetic PMDA modified biomass by a situ co-precipitation method under the assistance of ultrasound irradiation in ammonia water. The adsorption potential of the as-prepared magnetic modified biomass was analyzed by using cationic dyes: methylene blue and basic magenta as model dyes. Optical micrograph and x-ray diffraction analyses showed that Fe₃O₄ particles were precipitated on the modified biomass surface. The as-prepared biosorbent could be recycled easily by using an applied magnetic field. Titration analysis showed that the total concentration of the functional groups on the magnetic PMDA modified biomass was calculated to be 0.75 mmol g^?1 by using the first derivative method. The adsorption capacities (q _m) of the magnetic PMDA modified biomass for methylene blue and basic magenta were 609.0 and 520.9 mg g^?1, respectively, according to the Langmuir equation. Kinetics experiment showed that adsorption could be completed within 150 min for both dyes. The desorption experiment showed that the magnetic sorbent could be used repeatedly after regeneration. The as-prepared magnetic modified sorbent had a potential in the dyeing industry wastewater treatment.     

An overview of nanomaterials applied for removing dyes from wastewater

Organic dyes are one of the most commonly discharged pollutants in wastewaters; however, many conventional treatment methods cannot treat them effectively. Over the past few decades, we have witnessed rapid development of nanotechnologies, which offered new opportunities for developing innovative methods to treat dye-contaminated wastewater with low price and high efficiency. The large surface area, modified surface properties, unique electron conduction properties, etc. offer nanomaterials with excellent performances in dye-contaminated wastewater treatment. For examples, the agar-modified monometallic/bimetallic nanoparticles have the maximum methylene blue adsorption capacity of 875.0 mg/g, which are several times higher than conventional adsorbents. Among various nanomaterials, the carbonaceous nanomaterials, nano-sized TiO₂, and graphitic carbon nitride (g-C₃N₄) are considered as the most promising nanomaterials for removing dyes from water phase. However, some challenges, such as high cost and poor separation performance, still limit their engineering application. This article reviewed the recent advances in the nanomaterials used for dye removal via adsorption, photocatalytic degradation, and biological treatment. The modification methods for improving the effectiveness of nanomaterials are highlighted. Finally, the current knowledge gaps of developing nanomaterials on the environmental application were discussed, and the possible further research direction is proposed.     

真菌和细菌对染料吸附脱色的高效共培养体系研究

在含有真菌G 1培养液中加入染料厂污水排放口的污泥样品 ,从发生快速脱色降解染料的混合培养液中分离出 2株染料脱色细菌L_1和L_2 ,经API鉴定系统鉴定 ,确定菌株L_1为Enterobactersp .,菌株L_2为Peudomonassp .。研究比较了单一和不同组合混合的真菌G_1菌株 (Penicilliumsp .)、细菌L_1菌株 (Enterobactersp .)和L_2菌株 (Pseu domonassp .)对偶氮染料红M - 3BE(C .I .ReactiveRed 2 41)和蒽醌染料艳蓝KN -R(C .1.ReactiveBlue 19)的去除情况 ,发现G - 1真菌和 2种细菌组合的共培养体系对 5 0mg/L红M - 3BE和艳蓝KN -R处理 5h去除率达 10 0 %和 97.9% ,并且是以脱色降解作用为主 ,建立了染料脱色降解菌的最佳组合 ;进一步测定了此最佳共培养体系对另外 13种不同结构染料的脱色降解 ,结果表明 ,除对蒽醌染料R - 478脱色降解较差外 ,对其他染料均可在lh— 3d被完全脱色降解 ,表现出脱色降解染料的广谱性 ;向培养 4d的共培养体系中依次加入 8种染料 ,菌体可对染料连续脱色 ,维持脱色能力达 8d左右     

低频超声协同Fe-Ni-Mn/Al_2O_3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn/Al2O3催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H2O2等因素对酸性绿B降解效果的影响,结果表明:催化剂Fe-Ni-Mn/Al2O3与低频超声存在协同效应,催化剂的最佳投加量为6 g/L;酸性条件有利于染料的超声降解,当pH=3.8时,可取得最佳的降解效果;酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100 mg/L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体(air+Ar)>氧气>氩气;在反应过程中投加H2O2有利于染料降解率的提高.在优化实验条件下降解150 min,酸性绿B色度去除率达到91.4%.     

Photocatalytic mineralization of hydroperfluorocarboxylic acids with heteropolyacid H₄SiW₁₂O₄₀ in water

The decomposition of hydroperfluorocarboxylic acids [H-PFCAs; HC_nF_2nCOOH (n = 4 and 6)] induced by heteropolyacid photocatalyst H₄SiW₁₂O₄₀ in water was investigated, and the results are compared with the results for the corresponding perfluorocarboxylic acids (PFCAs; C_nF_2n+1COOH). This is the first report on the photochemical decomposition of H-PFCAs, which are being developed as alternative surfactants to environmentally persistent and bioaccumulative PFCAs. H-PFCAs were not decomposed by irradiation with UV-Visible light (>290 nm) in the absence of H₄SiW₁₂O₄₀. In contrast, UV-Visible light irradiation of H-PFCAs in the presence of H₄SiW₁₂O₄₀ efficiently decomposed H-PFCAs to F⁻ and CO₂. The decomposition reactions showed pseudo-first-order kinetics, and the decomposition rate constants were 1.8-2.5 times higher than those for the corresponding PFCAs. The reaction mechanism can be explained by elimination of H⁺ from the ω-H atom of the H-PFCAs by the excited catalyst, followed by formation of perfluorodicarboxylic acids.     

Study of the degradation of dyes by MnP of Phanerochaete chrysosporium produced in a fixed-bed bioreactor

The production of ligninolytic enzymes by the fungus Phanerochaete chrysosporium in a fixed-bed tubular bioreactor, filled with cubes of nylon sponge, operating in semi-solid-state conditions, was studied. Maximum individual manganese-dependent peroxidase (MnP) and lignin peroxidase (LiP) activities of 1293 and 225 U/l were detected.The in vitro decolourisation of two structurally different dyes (Poly R-478, crystal violet) by the extracellular liquid obtained in the above-mentioned bioreactor was monitored in order to determine its degrading capability. The concentration of some compounds (sodium malonate, manganese sulphate) from the reaction mixture was optimised in order to maximise the decolourisation levels. A percentage of Poly R-478 decolourisation of 24% after 15 min of dye incubation was achieved.On the other hand, a methodology for a long treatment of these dyes based on the continuous addition of MnP enzyme and H(2)O(2) was developed. Moreover, this enzymatic treatment was compared with a photochemical decolourisation process. The former allowed to maintain the degradation rate almost constant for a long time, resulting in a decolourisation percentage of 70% and 30% for crystal violet and Poly R-478, respectively, after 2 h of treatment. As for the latter, it was not able to degrade Poly R-478, whereas crystal violet reached a degradation of 40% in 2 h.     

Co3O4/介孔分子筛催化剂对苯催化完全氧化的研究

分别以介孔分子筛MCM-41、MCM-48、SBA-15为载体，采用等体积浸渍法制备了氧化钴/介孔分子筛催化剂，利用N₂吸附、X射线衍射、程序升温还原等技术对催化剂进行了表征，考察了Co₃O₄的负载量及载体的孔结构对催化剂完全催化氧化苯的性能的影响。结果表明，Co₃O₄的负载量为20%时，催化剂的催化活性最好；载体的孔径和催化剂的可还原性能是影响催化活性的主要因素，催化剂活性顺序为Co₃O₄ /SBA-15> Co₃O₄ /MCM41> Co₃O₄ /MCM-48。     

基于Ti/SnO_2阳极氧化法的典型染料废水电化学氧化规律

采用Ti/SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水,研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响;在最佳组合条件下,通过分析UV-Vis光谱以及降解过程中氮元素的存在形式,研究上述2种染料的降解规律。结果表明,在pH为3,电压20 V,NaCl投加量为2.5 g/L的条件下,电解30 min后,直接深棕M和活性艳蓝KNR的脱色率分别达到80%和95%,60 min后直接深棕M的COD去除率可达75%,活性艳蓝KNR的COD去除率达到90%;电解60 min后,直接深棕M的偶氮双键完全破坏,萘环和苯环结构被逐步降解,活性艳蓝KNR溶液电解2 min,其分子结构中的蒽醌共轭体系被破坏,随反应的进行,蒽醌结构逐渐被破坏,染料逐步降解。     

亚铁羟基络合物还原转化水溶性偶氮染料

偶氮染料是印染工艺中应用最广泛的一类染料,目前染料废水脱色是污水处理难题。亚铁混凝处理染料废水过程中可能存在亚铁的还原作用,本实验制备了比溶解态亚铁更具还原反应活性的亚铁羟基络合物(ferrous hydroxycomplex,FHC),以5种不同类型的水溶性偶氮染料为目标污染物,研究FHC还原水溶性偶氮染料的脱色性能。实验结果表明,FHC对活性艳红X-3B、酸性大红GR和阳离子红X-GRL有较好的还原脱色效果,仅投加含铁89.6 mg/L的FHC,染料脱色率达到90%以上,继续增大FHC投加量可以完全脱色;中性枣红GRL的FHC还原脱色效果较差,需加入313.6 mg/L的FHC才能达到90%以上脱色率;134.4 mg/L的FHC能够将直接耐酸大红4BS完全脱色,但其脱色主要以混凝沉淀为主;溶液pH对FHC的还原性能产生重要影响,FHC还原染料脱色的适宜的pH值范围为4～10。该研究为亲水性染料脱色提供了一种新的技术,也为FHC运用于印染废水脱色提供了理论基础。     

Degradation of dyes from aqueous solution by Fenton processes: a review

Several industries are using dyes as coloring agents. The effluents from these industries are increasingly becoming an environmental problem. The removal of dyes from aqueous solution has a great potential in the field of environmental engineering. This paper reviews the classification, characteristics, and problems of dyes in detail. Advantages and disadvantages of different methods used for dye removal are also analyzed. Among these methods, Fenton process-based advanced oxidation processes are an emerging prospect in the field of dye removal. Fenton processes have been classified and represented as “Fenton circle”. This paper analyzes the recent studies on Fenton processes. The studies include analyzing different configurations of reactors used for dye removal, its efficiency, and the effects of various operating parameters such as pH, catalyst concentration, H₂O₂ concentration, initial dye concentration, and temperature of Fenton processes. From the present study, it can be conclude that Fenton processes are very effective and environmentally friendly methods for dye removal.     

Decolorization of cationic red X-GRL by wet air oxidation: performance optimization and degradation mechanism

The decolorization of a strong colored azo dye solution of cationic red X-GRL was investigated by wet air oxidation under relatively mild conditions (60-180 degrees C, PO2 = 0-1.2 MPa). Mono-factor experiments were carried out to investigate the effect of the operation factors and the relatively important parameters were selected for optimization using response surface methodology to explore the interactions of these relatively important parameters. Model regeneration analysis and the check experiments showed that the data of the general linear model agreed with the experiment results well. With multistage Monte-Carlo optimization, the best region of these variables could be predicted to dye color removal. At typical operational conditions, the intermediates of dye degradation were detected and confirmed by GC/MS system. Considering the intermediates and the structure analysis with the help of Gaussian 03W (version 6.0) and the theory of dye color, a possible degradation mechanism for the wet air oxidation of cationic red X-GRL was discussed and the probable degradation pathway was deduced.