基于Ti/SnO2阳极氧化法的典型染料废水电化学氧化规律

采用Ti／SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水，研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响；在最佳组合条件下，通过分析uV—Vis光谱以及降解过程中氮元素的存在形式，研究上述2种染料的降解规律。结果表明，在pH为3，电压20V，NaCl投加量为2．5g／L的条件下，电解30min后，直接深棕M和活性艳蓝KNR的脱色率分别达到80％和95％，60min后直接深棕M的COD去除率可达75％，活性艳蓝KNR的COD去除率达到90％；电解60min后，直接深棕M的偶氮双键完全破坏，萘环和苯环结构被逐步降解，活性艳蓝KNR溶液电解2min，其分子结构中的蒽醌共轭体系被破坏，随反应的进行，蒽醌结构逐渐被破坏，染料逐步降解。     

间接阳极氧化处理活性黑5模拟染料废水的研究

采用Ti/IrO2电极间接阳极氧化处理活性黑5模拟废水,主要研究pH值、电压、电解时间及NaCl投加量对其降解效果的影响.结果表明,在pH值为3,电压20 V,电解时间60 min,NaCl投加量2.5 g/L的条件下,该染料的降解率及脱色率均达到100%,苯环结构的降解可达45%,COD去除率可达60%.并对该染料的...     

改进Fenton体系处理蒽醌染料的研究

以活性艳蓝KN-R作为研究对象,用UV/Fenton和solar/Fenton/草酸(H2C O4)体系对其进行处理,对反应体系的影响因素作综合的评价.得到处理蒽醌染料废水的最佳条件:dye(活性艳蓝KN-R):Fe2 :H2O2:H2C2O4为5:1:15:1.5,pH为3.0,反应时间为40 min.在最佳条件下,solar/Fenton/H2C2O4体系脱色率达到100%,COD和TOC去除率分别达到87%和66%以上.改进的Fenton方法能使难降解有机染料迅速脱色,矿化程度较高.并对此体系处理活性艳蓝KN-R废水的脱色过程进行动力学模拟,得到此反应为拟一级反应.     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

臭氧催化氧化处理活性蓝染料废水及催化剂的研究

进行了臭氧化学氧化体系和臭氧催化氧化体系对活性蓝处理效果的比较。提出了常温常压下臭氧催化氧化预处理活性蓝染料废水的新方法。实验结果表明，臭氧催化氧化处理COD为13 800 mg/L的活性蓝染料废水时，最佳反应pH值为5～6，臭氧用量为80 mg/L时，反应时间约40 min，COD去除率大于80%，色度去除率大于90%，达到了预处理要求。     

微波无极紫外光氧化-内电解工艺处理染料废水研究

在自制的微波激发无极紫外灯光氧化反应器和内电解反应器联用体系中,以次氯酸钠为氧化剂,对活性深兰M-2GE染料模拟废水进行处理.结果表明,投加次氯酸钠4 mL/L、微波紫外光反应时间30 min、内电解反应时间50 min时,活性深兰M-2GE染料模拟废水的脱色率、COD去除率可分别达到95%、70%的处理效果.     

二氧化氯催化氧化处理酸性大红染料废水研究

对经微电解预处理后的酸性大红染料配制废水进行二氧化氯催化氧化实验，结果表明：当废水COD在3400mg/L左右，pH=4，氧化反应时间为45min，二氧化氯（ClO2）投加量为750mg/L，在催化剂作用下，COD平均去除率约达到88%，而单一的ClO2氧化，其COD平均去除率仅为28%。     

粉煤灰协同微波-Fenton氧化法处理活性艳蓝KN-R染料废水

以粉煤灰联合微波-Fenton氧化工艺处理活性艳蓝KN-R生产废水,考察了粉煤灰投加量及吸附时间对处理效果的影响,并通过正交实验对微波-Fenton工艺参数进行了优化。实验结果表明,粉煤灰絮凝吸附与微波-Fenton氧化具有协同效应;在粉煤灰投加量为40 g/L,搅拌吸附时间为20 min,滤液pH值为4,Fe2＋和H2O2投加量分别为3.6 mmol/L和0.15 mol/L,微波功率为200 W,辐射反应时间为4 min的优化条件下,染料废水的处理效果最好,COD和色度的去除率分别达到90.90%和99.98%。     

电催化氧化处理变性木薯淀粉生产综合废水研究

采用DSA电极电催化处理变性木薯淀粉生产综合废水,研究了槽电压,电流密度,支持电解质,pH值,电解时间等因素对其中COD去除率的影响.在选定的实验条件下,槽电压8 V,电流密度为40 mA/cm2,支持电解质为0.1g/L的NaCl,pH值为8.5～9.0,电解2 h,废水中COD的去除率达88.3%.     

三维电极电化学氧化法深度处理DOP生产废水的研究

采用以铁板作阴、阳极,活性炭作填充粒子的三维电极电化学氧化法深度处理DOP生产废水。探讨了废水的pH、槽电压、极板间距、活性炭投加量和反应时间等因素对COD去除率的影响,并通过正交实验确定了处理DOP废水的最佳工艺条件,还对COD的降解动力学规律进行了初步探讨。结果表明,三维电极电化学氧化法处理DOP生产废水的最佳工艺条件为:pH值为5、电极间距为4 cm、槽电压为25 V、活性炭投加量为12 g/L、电解时间为90 min。在此条件下,COD去除率可达71.5%,出水COD浓度为50.9 mg/L,达到国家污水综合排放标准(GB8978-1996)的一级标准。三维电极电化学氧化法对COD的降解反应呈表观一级反应,降解速率方程为C=C0e-0.0124t。     

混凝辅助电化学法处理橙黄G染料废水

以石墨板为阳极，研究了电化学氧化法对橙黄G染料废水的降解效果。比较了在NaCl、Na2 SO4以及NaCl与FeSO4·7H2O组合的支持电解质体系中的处理效果，同时考察了电压、初始pH、电解质浓度、电极间距和电解时间等因素对废水中橙黄G脱色率及COD去除率的影响。研究结果表明，橙黄G的脱色主要是活性氯的氧化作用，橙黄G分子的矿化可能主要是电解过程中产生的·OH的作用，FeSO4·7H2O的加入增加了混凝作用，使得处理效果进一步提高。最佳脱色条件下橙黄G脱色率和COD的去除率分别为97．6％和56．3％，B／C（BOD／COD）由0．09提高至0．41，可生化性有较大改善，并且随着降解时间的增加，COD去除率逐渐升高。此结果表明，橙黄G废水COD的去除相对于脱色存在滞后性。     

电催化氧化技术处理制革综合废水

选择DSA电极中的钛基掺硼金钢石膜电极(Ti/BDD),用于制革综合废水的电催化氧化处理研究,考察了在不同的电流密度、电压、电解质、pH值和电解时间等因素对COD去除率和电流效率的影响。结果表明,控制电流密度为30mA/cm2,电压为8.0 V,电解质(NaCl)浓度为2.0 g/L,pH为4.0,电催化氧化处理2 h后,废水的COD和NH4+-N的去除率分别达到了83.6%和90.3%,BOD/COD为0.45,比能耗为35.34 kWh/kg COD,电流效率为37%。     

三维电极法深度处理维生素生产废水

采用三维电极法对维生素废水进行深度处理,分别以钛涂钌铱板、铁板和不锈钢板作为电极阳极,石墨板作为电极阴极,柱状活性炭作为粒子电极,结果表明,当以钛涂钌铱板作为阳极,以粒径为1 mm的柱状活性炭作为粒子电极时电解效果最好,COD和色度去除率最高。实验选择电解电压、电极板间距、电解时间和初始pH值作为主要影响因素进行正交实验,实验研究证明,各因素的影响大小为电解电压>电极板间距>电解时间>初始pH值,得到的最佳参数组合分别为:电解电压为10 V,电极板间距为8 cm,电解时间为20 min,初始pH值为4,得到COD和色度最大去除率分别为59.5%和93.57%。     

Evaluation of different electrochemical methods on the oxidation and degradation of Reactive Blue 4 in aqueous solution

The oxidation of a reactive dye, Reactive Blue 4, RB4, (C.I. 61205), widely used in the textile industries to color natural fibers, was studied by electrochemical techniques. The oxidation on glassy carbon electrode and reticulated vitreous carbon electrode occurs in only one step at 2.0 < pH < 12 involving a two-electron transfer to the amine group leading to the imide derivative. Dye solution was not decolorized effectively in this electrolysis process. Nevertheless, the oxidation of this dye on Ti/SnO2/SbO(x) (3% mol)/RuO2 (1% mol) electrode showed 100% of decolorization and 60% of total organic carbon removal in Na2SO4 0.2 M at pH 2.2 and potential of +2.4V. Experiments on degradation photoelectrocatalytic were also carried out for RB4 degradation in Na2SO4 0.1 M, pH 12, using a Ti/TiO2 photoanode biased at +1.0 V and UV light. After 1h of electrolysis the results indicated total color removal and 37% of mineralization.     

三维过电位电解处理罗丹明B废水

选用钛基RuO2-TiO2涂层电极作为三维过电位电解装置的阳极，紫铜作为阴极，活性炭作为第三极，研究了三维过电位电解处理罗丹明B废水的效果，并考察了外加电压、电解时间、初始浓度、pH值和搅拌方式等因素对其处理效果的影响。实验结果表明，外加电压、电解时间和初始浓度等因素均对罗丹明B的降解效果有影响，而pH值、搅拌方式等对罗丹明B的降解效果基本没有影响。与二维电解的对比研究表明，在罗丹明B溶液初始浓度为20mg／L，电解时间为1h，电解电压为20V时，采用二维电解的降解率为20％左右，而三维过电位电解的降解率接近80％。最终产物分析结果显示，经过处理的罗丹明B苯环开环变成直链烃类物质，或者饱和环状有机物，不再具有生物毒性，适合后续的生化处理。     

Electrolytic removal of Rhodamine B from aqueous solution by peroxicoagulation process

Peroxicoagulation treatment of aqueous solution containing hazardous dye, Rhodamine B, with commercially available graphite as cathode and iron as anode has been studied. The effect of various operational parameters such as solution pH, applied voltage, electrode area, other ions, etc. on the dye removal was investigated. The experimental result showed that pH-regulated peroxicoagulation system is an efficient process for the dye removal. Ninety-five percent of the dye was removed after 180 min of electrolysis. Anions such as carbonate, bicarbonate, chloride and sulphate negatively affected the efficiency of peroxicoagulation system. From the present study, it can be concluded that peroxicoagulation process is an efficient tool for dye removal from aqueous solution.     

Degradation of azo dye Acid Red 14 in aqueous solution by electrokinetic and electrooxidation process

A new wastewater treatment technology--electrokinetic-electrooxidation process (EK-EO process) is developed in this paper. The EK-EO process can take advantage of both electrooxidation on the anode surface and the electrokinetic process of anionic impurities under an electric field, which can enhance the TOC removal in electrolysis process. The degradation of an anionic azo dye Acid Red 14 (AR14) was experimentally investigated. It was found that under an electric field AR14 could be migrated into anode compartment and be efficiently mineralized. After 360 min electrolysis of 100 mgl(-1) AR14 solutions at 4.5 mAcm(-2), complete discoloration was observed in both cathode and anode compartment. About 60% TOC was electromigrated from cathode compartment to anode compartment, and more than 25 mgl(-1) TOC was abated in anode compartment. A possible degradation mechanism of AR14 by EK-EO process was proposed. Additionally, the effect of current density, recycling flux, and electrolyte concentration on the EK-EO degradation of AR14 was also investigated.     

组合阳极联合气体扩散阴极电催化降解苯胺

采用气体扩散电极为阴极，钛基氧化物（Ti／SnO2-Sb2O5-IrO2）和金属铁构成组合阳极，构建了新型电化学氧化体系用于降解有机污染物。利用该氧化体系，在不同实验条件下考察了苯胺降解的效果与降解过程的相关规律。结果表明，阴极电位、铁阳极通电时间以及苯胺初始浓度均显著影响苯胺的降解效果。当阴极电位为-0．7V，pH3．0，铁阳极通电时间20min时，电化学处理200mg／L苯胺480min，TOC的去除效率达到80．4％，矿化电流效率（MCE）为8．6％，显示了该氧化体系具有良好的有机物降解能力。此外，苯胺降解过程中氨氮和硝态氮浓度的变化表明，苯胺分子中的氮主要转化为NH4和NO3^-。     

Electro-Fenton pretreatment for the improvement of tylosin biodegradability

The feasibility of an electro-Fenton process to treat tylosin (TYL), a non-biodegradable antibiotic, was examined in a discontinuous electrochemical cell with divided cathodic and anodic compartments. Only 15 min electrolysis was needed for total tylosin degradation using a carbon felt cathode and a platinum anode; while 6 h electrolysis was needed to achieve high oxidation and mineralization yields, 96 and 88 % respectively. Biodegradability improvement was shown since BOD₅/COD increased from 0 initially to 0.6 after 6 h electrolysis (for 100 mg L^?1 initial TYL). With the aim of combining electro-Fenton with a biological treatment, an oxidation time in the range 2 to 4 h has been however considered. Results of AOS (average oxidation state) and COD/TOC suggested that the pretreatment could be stopped after 2 h rather than 4 h; while in the same time, the increase of biodegradability between 2 and 4 h suggested that this latter duration seemed more appropriate. In order to conclude, biological cultures have been therefore carried out for various electrolysis times. TYL solutions electrolyzed during 2 and 4 h were then treated with activated sludge during 25 days, showing 57 and 67 % total organic carbon (TOC) removal, respectively, namely 77 and 88 % overall TOC removal if both processes were considered. Activated sludge cultures appeared, therefore, in agreement with the assessment made from the analysis of physico-chemical parameters (AOS and COD/TOC), since the gain in terms of mineralization expected from increasing electrolysis duration appeared too low to balance the additional energy consumption.