Effect of pH,ionic strength,and background electrolytes on Cr(VI) and total chromium removal by acorn shell of Quercus crassipes Humb. & Bonpl.

The ability of Quercus crassipes acorn shells (QCS) to remove Cr(VI) and total chromium from aqueous solutions was investigated as a function of the solution pH, ionic strength, and background electrolytes. It was found that Cr(VI) and total chromium removal by QCS depended strongly on the pH of the solution. Cr(VI) removal rate increased as the solution pH decreased. The optimum pH for total chromium removal varied depending on contact time. NaCl ionic strengths lower than 200 mM did not affect chromium removal. The presence of 20 mM monovalent cations and anions, and of divalent cations, slightly decreased the removal of Cr(VI) and total chromium by QCS; in contrast, divalent anions (SO₄ ^2?, PO₄ ^2?, CO₃ ^2?) significantly affected the removal of Cr(VI) and total chromium. The biosorption kinetics of chromium ions followed the pseudo-second-order model at all solution pH levels, NaCl ionic strengths and background electrolytes tested. Results suggest that QCS may be a potential low-cost biosorbent for the removal of Cr(VI) and total chromium from aqueous solutions containing various impurities.     

Chromium speciation in groundwater of a tannery polluted area of Chennai City, India

Chromium speciation in groundwater of a tannery polluted area was investigated for the distribution of chromium species and the influence of redox couples such as Fe(III)/Fe(II) and Mn(IV)/Mn(II). Speciation analysis was carried out by ammonium pyrolidinedithiocarbamate (APDC)–methylisobutylketone (MIBK) procedure. The groundwater samples were analyzed for Cr(III), Cr(VI), and Cr(III)-organic complexes. The APDC could not extract the Cr(III)-organic complexes, but HNO₃ digestion of the groundwater samples released the Cr(III)-organic complexes. The groundwater of the area is relatively oxidizing with redox potential (E _h) and dissolved oxygen (DO) ranged between 65 and 299 mV and 0.25 and 4.65 mg L^???1, respectively. The Fe(II) reduction of Cr(VI) was observed in some wells, but several wells that had Fe(II)/Cr(VI) concentrations more than the stoichiometric ratio (3:1) of the reduction reaction also had appreciable concentration of Cr(VI). This could partly be due to the oxidation of Fe(II) to Fe(III) by DO. It appears that the occurrence of Mn more than the Fe(II) concentration was also responsible for the presence of Cr(VI). Other reasons could be the Fe(II) complexation by organic ligands and the loss of reducing capacity of Fe(II) due to aquifer materials, but could not be established in this study.     

Flow injection analysis of trace chromium (VI) in drinking water with a liquid waveguide capillary cell and spectrophotometric detection

Hexavalent chromium (Cr(VI)) is an acknowledged hazardous material in drinking waters. As such, effective monitoring and assessment of the risks posed by Cr(VI) are important analytical objectives for both human health and environmental science. However, because of the lack of highly sensitive, rapid, and simple procedures, a relatively limited number of studies have been carried out in this field. Here we report a simple and sensitive analytical procedure of flow injection analysis (FIA) for sub-nanomolar Cr(VI) in drinking water samples with a liquid core waveguide capillary cell (LWCC). The procedure is based on a highly selective reaction between 1, 5-diphenylcarbazide and Cr(VI) under acidic conditions. The optimized experimental parameters included reagent concentrations, injection volume, length of mixing coil, and flow rate. Measurements at 540 nm, and a 650-nm reference wavelength, produced a 0.12-nM detection limit. Relative standard deviations for 1, 2, and 10 nM samples were 5.6, 3.6, and 0.72 % (n?=?9), and the analysis time was <2 min sample^?1. The effects of salinity and interfering ions, especially Fe(III), were evaluated. Using the FIA-LWCC method, different sources of bottled waters and tap waters were examined. The Cr(VI) concentrations of the bottled waters ranged from the detection limit to ～20 nM, and tap waters collected from the same community supply had Cr(VI) concentration around 14 nM.     

Speciative determination of Cr (III) and Cr (VI) in dyeing waste water of Dil Creek discharge to Izmit Gulf (Izmit-Kocaeli, Turkey) by ICP-AES

Wastewater pollution in industrial areas is one of the most important environmental problems. Heavy metal pollution, especially chromium pollution in wastewater sources from dyeing and tannery has affected the life on earth. This pollution can affect all ecosystems and human health directly or by food chain. Therefore, the determination of chromium in this study is of great importance. Dil Creek is located in the eastern Marmara region and discharges into the Izmit Gulf. This water source is used for irrigation in agriculture and as drinking water for animals. In this study, a rapid, sensitive and selective method for the speciative direct determination of Cr (III) and Cr (VI) in dyeing waste water samples collected from the nearest station to Izmit Gulf of Dil Creek in May 2006 by inductively coupled plasma-atomic emission spectrometry (ICP-AES) has been developed. An analysis of a given sample is completed in about 15 min for ICP-AES the method. As the result of the chromium analysis, the limit of quantification (LOQ) for the Cr (III), Cr (VI) and total Cr were founded as 0.0111 ± 0.0002 mg/l (RSD, 1.80%), 0.0592 ± 0.0010 mg/l (RSD, 1.70%) and 0.0703 ± 0.0020 mg/l (RSD, 2.84%) respectively. In addition, the general mathematical formula has been developed to calculate the concentration of Cr(III), which can be applied to any other metal species. The result of Cr (VI) analysis indicated that water quality of Creek was IV. class quality according to the inland water classification. In order to validate the applied method, recovery studies were performed.     

Chromium speciation in a contaminated groundwater: redox processes and temporal variability

Chromium species (Cr(III), Cr(VI), and Cr(III)-organic) in groundwater of a tannery contaminated area were monitored during pre- and post-monsoon seasons for a period of 3 years (May 2004 to January 2007). The objectives of the study were (1) to investigate the temporal variation of chromium species and other matrix constituents and (2) to study the redox processes associated with the temporal variation of chromium species. Samples were collected from 15 dug wells and analyzed for chromium species and other constituents. The results showed that the groundwater was relatively more oxidizing during post-monsoon periods than the pre-monsoon periods. Except one sample, the concentration of chromium species were found in the order of Cr(VI)>Cr(III)>Cr(III)-organic complexes during all the pre- and post-monsoon periods. In most of the wells, the concentrations of Cr(III), Cr(VI), and Cr(III)-organic decreased during post-monsoon periods compared to their pre-monsoon concentrations. However, the Cr(VI)/Cr_Total ratio still increased and the Cr(III)/Cr_Total ratio decreased during post-monsoon periods in most of the samples. The possible mechanisms for the temporal variation of chromium species were (1) Fe(II) reduction of Cr(VI) vs oxidation of Fe(II) by dissolved oxygen and (2) oxidation of Cr(III) by Mn(IV).     

Solid phase extraction and determination of Cr(III) by spectrophotometry using cefaclor as a complexing reagent and FAAS

The present study reports on the application of modified groundnut shell as a new, easily prepared, and stable sorbent for the extraction of trace amount of Cr(III) in aqueous solution. 2-Hydroxybenzaldiminoglycine was immobilized on groundnut shells in alkaline medium and then used as a solid phase for the column preconcentration of Cr(III). The elution was carried out with 3 mL of 2 mol?L^?1 HCl. The amount of eluted Cr(III) was determined by spectrophotometry using cefaclor as a complexing reagent and by flame atomic absorption spectrometry (FAAS). Different experimental variables such as pH, amount of solid sorbent, volume and concentration of eluent, sample and eluent flow rate, and interference of other metal ions on the retention of Cr(III) were studied. Under the optimized conditions, the calibration curves were found to be linear over the concentration range of 13–104 and 10–75 μg?L^?1 with a detection limit of 3.64 and 1.24 μg?L^?1 for spectrophotometric method and FAAS, respectively. An enrichment factor of 200 and RSD of ±1.19–1.49 % for five successive determinations of 25 μg?L^?1 were achieved. The column preconcentration was successfully applied to the analysis of tap water and underground water samples.     

Determination of total Cr in wastewaters of Cr electroplating factories in the I.organize industry region (Kayseri, Turkey) by ICP-AES

The wastewater pollution in industrial areas is one of the most important environmental problems. Heavy metal pollution, especially chromium pollution in the wastewater sources from electroplating, dyeing, and tannery, has affected the life on earth. This pollution can affect on all ecosystems and human health directly or by food chain. Therefore, the determination of total chromium in this study is of great importance. In this study, accurate, rapid, sensitive, selective, simple, and low-cost technique for the direct determination of total Cr in wastewater samples collected from the some Cr electroplating factories in March 2008 by inductively coupled plasma-atomic emission spectrometry has been developed. The analysis of a given sample is completed in about 15 min by this technique applied. As the result of the chromium analysis, the limit of quantification for the total Cr were founded to be over the limit value (0.05 mg L^???1; WHO, EPA, TSE 266, and inland water quality classification) as 1,898.78 ± 0.34 mg/L at station 1 and 3,189.02 ± 0.56 mg/L at station 2. The found concentration of total Cr has been determined to be IV class quality water according to the inland water classification. In order to validate the applied method, recovery studies were performed.     

Effect of air-drying and oven-drying treatment on Cr(VI) content and Cr bond forms in soil

Air-drying and oven-drying are pretreatment processes often used before testing and analyzing various soil characteristics in the laboratory. This study selected three kinds of soil, including red soil, entisol, and alluvial soil, and examined the variation of the Cr(VI) content and Cr bond forms in these soils during air-drying and oven-drying. The results show that when the soil is air-dried in natural environment, the Cr(VI) content decreases with air-drying time. On day 10 of air-drying, the Cr(VI) content in these soils is 22.8～47.9 % of the initial value. When the soil is oven-dried, the Cr(VI) concentration decays faster; on day 8, the Cr(VI) is no longer detected in these soil samples. When the Cr(VI)-contaminated soil is treated by air-drying and oven-drying, the Cr bond form converts into a more stable form. After oven-drying, the Cr mainly exists in Fe–Mn oxide form, organic bond form, and residual form. The air-drying and oven-drying pretreatment processes of soil reduce the Cr(VI) content and stabilize the Cr bond form. If the laboratory analytic results are applied to risk analysis or remediation strategy planning for chromium-contaminated soil, the toxicity, bioavailability, and mobility of Cr in soil may be underrated.     

Simultaneous quantification of Bi(III) and U(VI) in environmental water samples with a complicated matrix containing organic compounds

Trace amounts of bismuth(III) and uranium(VI) can be simultaneously determined in a single scan by adsorptive cathodic stripping voltammetry in the presence of cupferron as a complexing agent. Optimal conditions were found to be: 0.1 mol?L^?1 acetate buffer (pH 5.3), 5?×?10^?5?mol?L^?1 cupferron, accumulation potential of ?0.25 V, and accumulation time of 30 s. The linear range of Bi(III) and U(VI) was observed over the concentration range from 2?×?10^?9 to 2?×?10^?7?mol?L^?1 and from 1?×?10^?8 to 5?×?10^?7?mol?L^?1, respectively. The influence of the main components of real water samples such as foreign ions and organic substances (surface active substances, humic substances) was precisely investigated. The method was applied to the simultaneous measurements of bismuth and uranium in natural water samples.     

Tuning the surfaces of palladium nanoparticles for the catalytic conversion of Cr(VI) to Cr(III)

This work reports the feasibility of using Pd nanoparticles as innovative catalysts in the conversion of reducible contaminants from toxic to benign forms. Cr(VI) is a known carcinogen while the trivalent chromium salts are believed to be non-toxic. The ability of Pd nanoparticles to catalyze the rapid reduction of Cr(VI) to Cr(III) using reactive sulfur intermediates produced in situ was therefore studied. Using a microchamber set at 130 degrees C, the reduction mixture consists of palladium nanoparticles and sulfur (PdNPs/S), which generated highly reducing sulfur intermediates that effected the reduction of Cr(VI) to Cr(III) by 1st order reaction kinetics. UV-visible spectroscopy and cyclic voltammetry were employed to monitor the reduction process. The results showed that 99.8% of 400 microM Cr(VI) was reduced to Cr(III) by PdNPs/S in one hour compared to 2.1% by a control experiment consisting of sulfur only. The rate of Cr(VI) reduction was found to be dependent on temperature and pH and was greatly enhanced by the addition of PdNPs. Subsequent application of this approach in the reduction of Cr(VI) in soil and aqueous media was conducted. In contrast to the control experiments with and without PdNPs or sulfur, greater than 92% conversion rate was obtained in the presence of PdNPs/S within 1 hour. This represents over a 500-fold improvement in conversion rate compared to current microbial approaches. XPS analysis provided the confirmation regarding the oxidation states of Cr(VI), Cr(III) and the nature of the reactive intermediates. This work offers PdNPs/S as a new interface for the reduction of high oxidation state heavy metal pollutants.     

FIA-coupled spectrophotometric method for determination of Cr (VI) traces in natural waters: application of in-line dissolution of 1,5-diphenylcarbazide after heat treatment and activated alumina as adsorbent for preconcentration

This work proposes the quantification of Cr (VI) ions in natural waters in trace level, using activated alumina (Al₂O₃) as preconcentration support, controlled in-line dissolution of the solidified chromophore diphenylcarbazide after heat treatment and spectrophotometric detection. The manifold ensures high sensitivity of analytical response, good repeatability, and stability. In this work, optimization of experimental conditions of a flow injection system was chosen as the parameters for greater sensitivity and better selectivity. The selected optimized conditions were 0.30 mol L^?1 for H₂SO₄ concentration, system flow rate as 0.40 mL min^?1, sample injection volume of 192.50 μL, 2 min for preconcentration time, and 0.10 mol L^?1 for eluent concentration. The analytical curves obtained for real sample analysis show linear range from 0.192 to 0.961 μM, linear correlation coefficient R?=?0.9997 and LOD?=?0.024 μM. The preconcentration factor of about four times was obtained through the passage of 800 μL of a standard solution containing 0.961 μM of Cr (VI) through mini-column of preconcentration followed by elution at 192.5 μL of NH₄OH 0.1 mol L^?1 solution. The solid chromogenic reagent presented high durability (weeks in daily use with mass of 0.0993 g) and good reproducibility in analytical signal. The reactivation of the mini-column of alumina should be executed after ten injections of eluent, using 800 μL of HCl 0.02 mol L^?1 solution in flow through the same. Each cycle of injection and elution of the sample takes about 5 min on the proposed terms. Despite the length of each cycle still be high, low concentrations can be detected using a technique of relatively low cost. This is due in part, the association dissolution of the chromogenic reagent directly in the line and the preconcentration step. Another important factor is the economy of reagent chromogenic, low generation of reject contributing to better quality of the environment, and the high potential for applications to work in field.     

Oxidation of Cr(III) to Cr(VI) during chlorination of drinking water

Drinking water treatment typically uses strong oxidants such as chlorine which are capable of converting Cr(III) to Cr(VI). The rates and extent of Cr(III) oxidation by chlorine are not well established. Cr(III) oxidation experiments were therefore conducted in distilled deionized water and New York City tap water dosed initially with Cr(III) and supplemented with sodium hypochlorite to increase free chlorine residual. Reaction progress was monitored using capillary electrophoresis which quenched reactions and allowed for quantification of Cr(VI). Three different forms of Cr(III) were used as reactants: a Cr(III) nitrate salt, Cr(III)-EDTA, and Cr(III) hydroxide. Rates of Cr(VI) production for all three forms of Cr(III) were rapid, on the order of hours. However, oxidation rates slowed and a plateau in Cr(VI) concentrations was reached. This resulted in less than 100% conversion of Cr(III) to Cr(VI) even at relatively high chlorine doses (10 to 100 mg L(-1) as Cl(2)). The loss of free chlorine due to a non-Cr chlorine demand, the precipitation of Cr(III) to Cr(OH)(3)(s), and the partial oxidation of Cr(III) to intermediate oxidation states (i.e. Cr(IV) and Cr(V)) were examined and eliminated as possible explanations for this behavior. Consumption of chlorine via reaction with intermediate oxidation states of Cr is therefore offered as a possible explanation for the plateau in Cr(VI) concentrations.     

Modeling nonlinearly transient zero-order bioreduction and transport of Cr(VI) in groundwater

Cr(VI) contamination of soil and groundwater is considered a major environmental concern. Bioreduction of Cr(VI) to Cr(III) can be considered a potentially effective technology in remediating Cr(VI) contaminated sites. Shewanella oneidensis MR-1 (MR-1) is one of the bacteria capable of reducing Cr(VI) to Cr(III) under anaerobic conditions. The kinetics of Cr(VI) reduction by MR-1 is defined by the dual-enzyme kinetic model which is nonlinear, transient, and zero-order. Existing transport models are not designed to simulate such reaction kinetics. The objective of this paper is to present a Petrov–Galerkin finite element model (PGFEM) to simulate transport and bioreduction of Cr(VI), by MR-1, in groundwater. The model developed is unconditionally stable and provides oscillation free accurate results for a wide range of Peclet number (Pn) and Courant number (Cn).     

Geochemical assessment of metal transport in glacial till during electrokinetic remediation

This paper presents the chemical speciation and retention behavior of chromium (Cr), nickel (Ni), and cadmium (Cd) prior to and after the electrokinetic remediation in glacial till soil. The speciation of the metals was predicted using the chemical speciation program MINEQL⁺. The simulations were performed for single-contaminant with only Cr(VI) or Ni, and multi-contaminants consisting of: (1) Cr(VI), Ni, and Cd; (2) Cr(III), Ni and Cd; (3) Cr(VI), Cr(III), Ni and Cd; (4) Cr(VI), Ni, and Cd with reducing agents; and (5) Cr(III), Ni, and Cd with oxidizing agent (Mn). The results showed that the speciation and distribution of cationic metals [Ni, Cd, and Cr(III)] in glacial till soil remain unaffected or slightly affected during electrokinetics. This is attributed to the high pH buffering capacity of the glacial till, leading the metals to precipitate in the soil prior to and after electrokinetics. This study showed that during electrokinetics, Cr(VI) existed as anionic complex and migrated towards the anode and the migration is maximum in case of a single-contaminant system. The study also showed that near the anode in the absence of any reducing and oxidizing agent, Cr(VI) mostly adsorbed, and some of Cr(VI) reduced to Cr(III) and migrated towards the cathode and finally precipitated due to high pH conditions. Ni and Cd remain adsorbed or precipitated due to the high pH conditions throughout the soil. Among the reducing agents, the sulfide had significant effect on the migration of metals compared to ferrous ions. While in the presence of oxidizing agent (Mn), no noticeable Cr(VI) was found in the soil sample indicating the reduction of Cr(VI) to Cr(III) and the predominance of reducing conditions due to the presence of naturally occurring iron in the glacial till soil. Overall, this study provides a reasonable explanation of the speciation and distribution of chromium, nickel and cadmium during the electrokinetic remediation of glacial till soil.     

Modeling of Cr contamination in the agricultural lands of three villages near the leather industry in Kasur,Pakistan, using statistical and GIS techniques

Kasur is one of the hubs of leather industry in the Punjab, Pakistan, where chrome tanning method of leather processing is extensively being used. Chromium (Cr) accumulation levels in the irrigation water, soil, and seasonal vegetables were studied in three villages located in the vicinity of wastewater treatment plant and solid waste dumping site operated by the Kasur Tanneries Waste Management Agency (KTWMA). The data was interpreted using analysis of variance (ANOVA), clustering analysis (CA), and principal component analysis (PCA). Interpolated surface maps for Cr were generated using the actual data obtained for the 30 sampling sites in each of the three villages for irrigation water, soil, and seasonal vegetables. The level of contamination in the three villages was directly proportional to their distance from KTWMA wastewater treatment plant and the direction of water runoff. The highest level of Cr contamination in soil (mg kg^?1) was observed at Faqeeria Wala (37.67), intermediate at Dollay Wala (30.33), and the least in Maan (25.16). A gradational variation in Cr accumulation was observed in the three villages from contaminated wastewater having the least contamination level (2.02–4.40 mg L^?1), to soil (25.16–37.67 mg kg^?1), and ultimately in the seasonal vegetable crops (156.67–248.33 mg kg^?1) cultivated in the region, having the highest level of Cr contamination above the permissible limit. The model used not only predicted the current situation of Cr contamination in the three villages but also indicated the trend of magnification of Cr contamination from irrigation water to soil and to the base of the food chain. Among the multiple causes of Cr contamination of vegetables, soil irrigation with contaminated groundwater was observed to be the dominant one.     

Chromium (VI) biosorption properties of multiple resistant bacteria isolated from industrial sewerage

Chromium (VI) [Cr (VI)] biosorption by four resistant autochthonous bacterial strains was investigated to determine their potential for use in sustainable marine water-pollution control. Maximum exchange between Cr (VI) ions and protons on the cells surfaces were at 30–35 °C, pH?2.0 and 350–450 mg/L. The bacterial strains effectively removed 79.0–90.5 % Cr (VI) ions from solution. Furthermore, 85.3–93.0 % of Cr (VI) ions were regenerated from the biomasses, and 83.4–91.7 % of the metal was adsorbed when the biomasses was reused. Langmuir isotherm performed better than Freundlich isotherm, depicting that Cr (VI) affinity was in the sequence Rhodococcus sp. AL03Ni?>?Burkholderia cepacia AL96Co?>?Corynebacterium kutscheri FL108Hg?>?Pseudomonas aeruginosa CA207Ni. Biosorption isotherms confirmed that Rhodococcus sp. AL03Ni was a better biosorbent with a maximum uptake of 107.46 mg of Cr (VI) per g (dry weight) of biomass. The results highlight the high potential of the organisms for bacteria-based detoxification of Cr (VI) via biosorption.     

Total and available heavy metal concentrations in soils of the Thriassio plain (Greece) and assessment of soil pollution indexes

The Thriassio plain is located 25 km west of Athens city, the capital of Greece. Two major towns (Elefsina and Aspropyrgos), heavy industry plants, medium to large-scale manufacturing, logistics plants, and agriculture comprise the main land uses of the studied area. The aim of the present study was to measure the total and available concentrations of Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe in the top soils of the plain, and to asses soil contamination by these metals by using the geoaccumulation index (I _geo), the enrichment factor (EF), and the availability ratio (AR) as soil pollution indexes. Soil samples were collected from 90 sampling sites, and aqua regia and DTPA extractions were carried out to determine total and available metal forms, respectively. Median total Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe concentrations were 78, 155, 81, 112, 24, 321, 834, 38, and 16?×?10³ mg?kg^?1, respectively. The available fractions showed much lower values with medians of 0.4, 5.6, 1.7, 6.9, 0.8, 5.7, 19.8, 2.1, and 2.9 mg?kg^?1. Though median total metal concentrations are not considered as particularly high, the I _geo and the EF values indicate moderate to heavy soil enrichment. For certain metals such as Cr, Ni, Cu, and Ba, the different distribution patterns between the EFs and the ARs suggest different origin of the total and the available metal forms. The evaluation of the EF and AR data sets for the soils of the two towns further supports the argument that the EFs can well demonstrate the long-term history of soil pollution and that the ARs can adequately portray the recent history of soil pollution.     

UV/H2O2 oxidation of arsenic and terbuthylazine in drinking water

Arsenic is a widespread contaminant in the environment. The intake of water containing high concentrations of arsenic could have serious impact on human health, such as skin and lung cancer. In the European Union, thus, also in Italy, the arsenic limit in drinking water is 10 μg L^?1. Several water remediation treatment technologies are available for arsenic removal. For some processes, the removal efficiencies can be improved after an oxidation step. Most full-scale applications are based on conventional oxidation processes for chemical micropollutant removal. However, if water contains arsenic and refractory organic contaminants, the advanced oxidation processes could be considered. The aim of this work was to investigate the effectiveness of ultraviolet (UV) radiation alone and in combination with hydrogen peroxide for the oxidation of arsenic and terbuthylazine (TBA). The experimental tests were performed in groundwater at the laboratory scale (0.1 mg L^?1 As(III) and 10 μg L^?1 TBA). Hydrogen peroxide alone (15 mg L^?1) was ineffective on both arsenic and TBA oxidation; the 253.7-nm radiation alone did not oxidize arsenic(III), but photolyzed efficiently TBA (52 % removal yield at a UV dose of 1,200 mJ cm^?2). The UV/H₂O₂ advanced oxidation (UV dose 600–2,000 mJ cm^?2, 5–15 mg L^?1 H₂O₂) was the most effective process for the oxidation of both arsenic and TBA, with observed oxidation efficiencies of 85 and 94 %, respectively, with 5 mg L^?1 H₂O₂ and a UV dose of 2,000 mJ cm^?2.     

Ferti-irrigational impact of sugar mill effluent on agronomical characteristics of Phaseolus vulgaris (L.) in two seasons

Ferti-irrigation response of 5, 10, 25, 50, 75, and 100 % concentrations of the sugar mill effluent (SME) on French bean (Phaseolus vulgaris L., cv. Annapurna) in the rainy and summer seasons was investigated. The fertigant concentrations produced significant (P?+), potassium (K⁺), calcium (Ca²⁺), magnesium (Mg²⁺), total Kjeldahl nitrogen (TKN), phosphate (PO₄ ^3?), sulfate (SO₄ ^2?), ferrous (Fe²⁺), cadmium (Cd), chromium (Cr), copper (Cu), manganese (Mn), and zinc (Zn), in both seasons. The contents of Cr, Cu, Mn, and Zn except Cd were found to be below the maximum levels permitted for soils in India. The agronomic performance of P. vulgaris was gradually increased at lower concentrations, i.e., from 5 to 25 %, and decreased at higher concentrations, i.e., from 50 to 100 %, of the SME in both seasons when compared to controls. The accumulations of heavy metals were increased in the soil and P. vulgaris from 5 to 100 % concentrations of the SME in both seasons. The contents of Cu, Mn, and Zn except Cd and Cr were noted under the permissible limit of Food and Agriculture Organization (FAO)/World Health Organization (WHO) standards. Most contents of biochemical components like crude proteins, crude fiber, and total carbohydrates were found with 25 % concentration of the SME in both seasons. The contamination factor (Cf) of various metals was in the order of Cd > Cr > Zn > Mn > Cu for soil and Mn > Zn > Cu > Cr > Cd for P. vulgaris in both seasons after fertigation with SME. Therefore, the SME can be used to improve the soil fertility and yield of P. vulgaris after appropriate dilution.     

Removal of hexavalent chromium from contaminated ground water using zero-valent iron nanoparticles

Batch experiments were conducted on ground water samples collected from a site contaminated with Cr(VI) to evaluate the redox potential of zero-valent iron (Fe⁰) nanoparticles for remediation of Cr(VI)-contaminated ground water. For this, various samples of contaminated ground water were allowed to react with various loadings of Fe⁰ nanoparticles for a reaction period of 60 min. Data showed 100% reduction of Cr(VI) in all the contaminated ground water samples after treatment with 0.20 gL⁻¹ of Fe⁰ nanoparticles. An increase in the reduction of Cr(VI) from 45% to 100% was noticed with the increase in the loading of Fe⁰ nanoparticles from 0.05 to 0.20 gL⁻¹. Reaction kinetics of Cr(VI) reduction showed pseudo first-order kinetics with rate constant in the range of 1.1 × 10⁻³ to 3.9 × 10⁻³ min⁻¹. This work demonstrates the potential utility of Fe⁰ nanoparticles in treatment and remediation of Cr(VI)-contaminated water source.