Phosphorus leaching from biosolids-amended sandy soils

Increasing emphasis on phosphorus (P)-based nutrient management underscores the need to understand P behavior in soils amended with biosolids and manures. Laboratory and greenhouse column studies characterized P forms and leachability of eight biosolids products, chicken manure (CM), and commercial fertilizer (triple superphosphate, TSP). Bahiagrass (Paspalum notatum Flugge) was grown for 4 mo on two acid, P-deficient Florida sands, representing both moderate (Candler series: hyperthermic, uncoated Typic Quartzipsamments) and very low (Immokalee series: sandy, siliceous, hyperthermic Arenic Alaquods) P-sorbing capacities. Amendments were applied at 56 and 224 kg P(T) ha(-1), simulating P-based and N-based nutrient loadings, respectively. Column leachate P was dominantly inorganic and lower for biosolids P sources than TSP. For Candler soil, only TSP at the high P rate exhibited P leaching statistically greater (alpha = 0.05) than control (soil-only) columns. For the high P rate and low P-sorbing Immokalee soil, TSP and CM leached 21 and 3.0% of applied P, respectively. Leachate P for six biosolids was <1.0% of applied P and not statistically different from controls. Largo biosolids, generated from a biological P removal process, exhibited significantly greater leachate P in both cake and pelletized forms (11 and 2.5% of applied P, respectively) than other biosolids. Biosolids P leaching was correlated to the phosphorus saturation index (PSI = [Pox]/[Al(ox) + Fe(ox)]) based on oxalate extraction of the pre-applied biosolids. For hiosolids with PSI < or = approximately 1.1, no appreciable leaching occurred. Only Largo cake (PSI = 1.4) and pellets (PSI = 1.3) exhibited P leaching losses statistically greater than controls. The biosolids PSI appears useful for identifying biosolids with potential to enrich drainage P when applied to low P-sorbing soils.     

A method for determining the phosphorus sorption capacity and amorphous aluminum of aluminum-based drinking water treatment residuals

A high amorphous aluminum or iron oxide content in drinking water treatment residuals (WTRs) can result in a high phosphorus (P) sorption capacity. Therefore, WTR may be used beneficially to adsorb P and reduce P loss to surface or ground water. The strong relationship between acid ammonium oxalate-extractable aluminum (Al(ox)) and Langmuir phosphorus adsorption maximum (P(max)) in WTR could provide a useful tool for determining P(max) without the onus of the multipoint batch equilibrations necessary for the Langmuir model. The objectives of this study were to evaluate and/or modify an acid ammonium oxalate extraction of Al(ox) and the experimental conditions used to generate P adsorption isotherms to strengthen the relationship between Al(ox) and P(max). The oxalate extraction solution to WTR ratio varied from 40:1, 100:1, and 200:1. Batch equilibration conditions were also varied. The WTR particle size was reduced from <2 mm to <150 microm, and batch equilibration was extended from 17 h to 6 d. Increasing the solution to WTR ratio to 100:1 extracted significantly greater Al(ox) at levels of >50 mg Al kg(-1). No additional increase was found at 200:1. Reducing WTR particle size from <2 mm to <150 microm increased P(max) 2.46-fold. Extending the equilibration time from 17 h to 6 d increased P(max) by a mean of 5.83-fold. The resulting empirical regression equation between the optimized Al(ox) and P(max) (r(2) = 0.91, significant at the 0.001 probability level) may provide a tool to estimate the P(max) of Al-based WTR simply by measuring Al(ox). The accurate determination of WTR P(max) and Al(ox) is essential in using WTR effectively to reduce P loss in runoff or to reduce the solubility of P in agricultural soils or organic waste materials (biosolids, manure).     

Surface applied water treatment residuals affect bioavailable phosphorus losses in Florida sands

Water treatment residuals (WTR) can reduce runoff P loss and surface co-application of P-sources and WTR is a practical way of land applying the residuals. In a rainfall simulation study, we evaluated the effects of surface co-applied P-sources and an Al-WTR on runoff and leacheate bioavailable P (BAP) losses from a Florida sand. Four P-sources, namely poultry manure, Boca Raton biosolids (high water-soluble P), Pompano biosolids (moderate water-soluble P), and triple super phosphate (TSP) were surface applied at 56 and 224kgPha(-1) (by weight) to represent low and high soil P loads typical of P- and N-based amendments rates. The treatments further received surface applied WTR at 0 or 10gWTRkg(-1) soil. BAP loss masses were greater in leachate (16.4-536mg) than in runoff (0.91-46mg), but were reduced in runoff and leachate by surface applied WTR. Masses of total BAP lost in the presence of surface applied WTR were less than approximately 75% of BAP losses in the absence of WTR. Total BAP losses from each of the organic sources applied at N-based rates were not greater than P loss from TSP applied at a P-based rate. The BAP loss at the N-based rate of moderate water-soluble P-source (Pompano biosolids) was not greater than BAP losses at the P-based rates of other organic sources tested. The hazards of excess P from applying organic P-sources at N-based rates are not greater than observed at P-based rates of mineral fertilizer. Results suggest that management of the environmental P hazards associated with N-based rates of organic materials in Florida sands is possible by either applying P-sources with WTR or using a moderate water-soluble P-source.     

Managing biosolids runoff phosphorus using buffer strips enhanced with drinking water treatment residuals

Vegetated buffers strips typically have limited ability to reduce delivery of dissolved phosphorus (DP) from agricultural fields to surface waters. A field study was conducted to evaluate the ability of buffer strips enhanced with drinking water treatment residuals (WTRs) to control runoff P losses from surface-applied biosolids characterized by high water-extractable P (4 g kg(-)(1)). Simulated rainfall (62.4 mm h(-1)) was applied to grassed plots (3 m x 10.7 m including a 2.67 m downslope buffer) surface-amended with biosolids at 102 kg P ha(-1) until 30 min of runoff was collected. With buffer strips top-dressed with WTR (20 Mg ha(-1)), runoff total P (TP = 2.5 mg L(-1)) and total DP (TDP = 1.9 mg L(-1)) were not statistically lower (alpha = 0.05) compared to plots with unamended grass buffers (TP = 2.7 mg L(-1); TDP = 2.6 mg L(-1)). Although the applied WTR had excess capacity (Langmuir P maxima of 25 g P kg(-1)) to sorb all runoff P, kinetic experiments suggest that sheet flow travel time across the buffers ( approximately 30 s) was insufficient for significant P reduction. Effective interception of dissolved P in runoff water by WTR-enhanced buffer strips requires rapid P sorption kinetics and hydrologic flow behavior ensuring sufficient runoff residence time and WTR contact in the buffer. Substantial phosphate-adsorbent contact opportunity may be more easily achieved by incorporating WTRs into P-enriched soils or blending WTRs with applied P sources.     

Use of drinking water treatment residuals as a potential best management practice to reduce phosphorus risk index scores

The P risk index system has been developed to identify agricultural fields vulnerable to P loss as a step toward protecting surface water. Because of their high Langmuir phosphorus adsorption maxima (P(max)), use of drinking water treatment residuals (WTRs) should be considered as a best management practice (BMP) to lower P risk index scores. This work discusses three WTR application methods that can be used to reduce P risk scores: (i) enhanced buffer strip, (ii) incorporation into a high soil test phosphorus (STP) soil, and (iii) co-blending with manure or biosolids. The relationship between WTR P(max) and reduction in P extractability and runoff P was investigated. In a simulated rainfall experiment, using a buffer strip enhanced with 20 Mg WTR ha(-1), runoff P was reduced by from 66.8 to 86.2% and reductions were related to the WTR P(max). When 25 g kg(-1) WTR was incorporated into a high STP soil of 315 mg kg(-1) determined using Mehlich-3 extraction, 0.01 M calcium chloride-extractable phosphorus (CaCl(2)-P) reductions ranged from 60.9 to 96.0% and were strongly (P < 0.01) related to WTR P(max). At a 100 g kg(-1) WTR addition, Mehlich 3-extractable P reductions ranged from 41.1 to 86.7% and were strongly (P < 0.01) related to WTR P(max). Co-blending WTR at 250 g kg(-1) to manure or biosolids reduced CaCl(2)-P by >75%. The WTR P(max) normalized across WTR application rates (P(max) x WTR application) was significantly related to reductions in CaCl(2)-P or STP. Using WTR as a P risk index modifying factor will promote effective use of WTR as a BMP to reduce P loss from agricultural land.     

Long-term phosphorus immobilization by a drinking water treatment residual

Excessive soluble P in runoff is a common cause of eutrophication in fresh waters. Evidence indicates that drinking water treatment residuals (WTRs) can reduce soluble P concentrations in P-impacted soils in the short term (days to weeks). The long-term (years) stability of WTR-immobilized P has been inferred, but validating field data are scarce. This research was undertaken at two Michigan field sites with a history of heavy manure applications to study the longevity of alum-based WTR (Al-WTR) effects on P solubility over time (7.5 yr). At both sites, amendment with Al-WTR reduced water-soluble P (WSP) concentration by >or=60% as compared to the control plots, and the Al-WTR-immobilized P (WTR-P) remained stable 7.5 yr after Al-WTR application. Rainfall simulation techniques were utilized to investigate P losses in runoff and leachate from surface soils of the field sites at 7.5 yr after Al-WTR application. At both sites, amendment with Al-WTR reduced dissolved P and bioavailable P (BAP) by >50% as compared to the control plots, showing that WTR-immobilized P remained nonlabile even 7.5 yr after Al-WTR amendment. Thus, WTR-immobilized P would not be expected to dissolve into runoff and leachate to contaminate surface waters or groundwater. Even if WTR-P is lost via erosion to surface waters, the bioavailability of the immobilized P should be minimal and should have negligible effects on water quality. However, if the WTR particles are destroyed by extreme conditions, P loss to water could pose a eutrophication risk.     

Phytoavailability of biosolids phosphorus

Efficient utilization of biosolids P for agronomic purposes requires accounting for differences in the phytoavailability of P in various biosolids. Greenhouse studies were conducted with a common pasture grass grown in two P-deficient soils amended with 12 biosolids and a commercial fertilizer (triple superphosphate, TSP) to quantify P uptake and to assess the relative phytoavailabilities of the P sources. Biosolids were grouped into three general categories of phytoavailability relative to TSP: high (> 75% of TSP), moderate (25-75% of TSP), and low (< 25% of TSP). Two biosolids, produced via biological phosphorus removal (BPR) processes, were in the high category, and mimicked fertilizer P with regard to P phytoavailability. Most biosolids produced by conventional wastewater and solids digestion and additional treatments like composting were in the moderate category. Also included in this category was a BPR that had been pelletized and another BPR supplemented with Al. The low category included biosolids containing greater than normal (> 50 g kg(-1)) total Fe and Al concentrations and processed to high (> 60%) solids content.     

Relationships between biosolids treatment process and soil phosphorus availability

Laws mandating phosphorus (P)-based nutrient management plans have been passed in several U.S. Mid-Atlantic states. Biosolids (sewage sludge) are frequently applied to agricultural land and in this study we evaluated how biosolids treatment processes and biosolids P tests were related to P behavior in biosolids-amended soils. Eight biosolids generated by different treatment processes, with respect to digestion and iron (Fe), aluminum (Al), and lime addition, and a poultry litter (PL), were incubated with an Elkton silt loam (fine-silty, mixed, active, mesic Typic Endoaquult) and a Suffolk sandy loam (fine-loamy, siliceous, semiactive, thermic Typic Hapludult) for 51 d. The amended soils were analyzed at 1 and 51 d for water-soluble phosphorus (WSP), iron-oxide strip--extractable phosphorus (FeO-P), Mehlich-1 P and pH. The biosolids and PL were analyzed for P, Fe, and Al by USEPA 3050 acid-peroxide digestion and acid ammonium oxalate, Mehlich-1, and Mehlich-3 extractions. Biosolids and PL amendments increased extractable P in the Suffolk sandy loam to a greater extent than in the Elkton silt loam throughout the 51 d of the incubation. The trend of extractable WSP, FeO-P, and Mehlich-1 P generally followed the pattern: [soils amended with biosolids produced without the use of Fe or Al] > [PL and biosolids produced using Fe or Al and lime] > [biosolids produced using only Fe and Al salts]. Mehlich-3 P and the molar ratio of P to [Al + Fe] by either the USEPA 3050 digestion or oxalate extraction of the biosolids were good predictors of changes in soil-extractable P following biosolids but not PL amendment. Therefore, the testing of biosolids for P availability, rather than total P, is a more appropriate tool for predicting extractable P from the biosolids-amended soils used in this study.     

Phosphorus release from a manure-impacted spodosol: effects of a water treatment residual

Long-term depositions of animal manures affect P dynamics in soils and can pose environmental risks associated with P losses. Laboratory studies were done on P solubility characteristics in a manure-impacted Immokalee soil (sandy, siliceous, hyperthermic Arenic Alaquod) and the effectiveness of water treatment residual (WTR) in controlling P leaching. Soil samples with contrasting initial total P concentrations were prepared by mixing samples of a manure-impacted surface A horizon and a minimally P-impacted E horizon. Effects of mixing various ratios of A and E horizons, WTR rates (0, 25, 50, and 100 g kg(-1)), and depths of WTR incorporation (mixed throughout the soil column or partially incorporated) on P leaching were determined. Between 62 and 77% of total P was released from the soil mixes by successive water extractions, suggesting a considerable buffering capacity of this manure-impacted soil to resupply P into solution. Between 224 and 408 mg kg(-1) P were leached during the 36-wk leaching period in the absence of WTR. Mixing WTRs with soil reduced soluble P concentration in leachates by as much as 99.8% compared with samples without WTR. Thoroughly mixing WTR with the entire soil column (15 cm) was much more efficient than mixing WTR with only the top 7.5 cm of soil. Calcium- and Mg-P forms appear to control P release in soils without WTR, whereas sorption-desorption reactions probably determine P leaching in WTR-treated samples. Soil P distribution in various chemical forms was affected by WTR additions. Data suggest that WTR-immobilized P is stable in the long term.     

Drinking water treatment residuals: a review of recent uses

Coagulants such as alum [Al2(SO4)3 x 14H2O], FeCl3, or Fe2(SO4)3 are commonly used to remove particulate and dissolved constituents from water supplies in the production of drinking water. The resulting waste product, called water-treatment residuals (WTR), contains precipitated Al and Fe oxyhydroxides, resulting in a strong affinity for anionic species. Recent research has focused on using WTR as cost-effective materials to reduce soluble phosphorus (P) in soils, runoff, and land-applied organic wastes (manures and biosolids). Studies show P adsorption by WTR to be fast and nearly irreversible, suggesting long-term stable immobilization of WTR-bound P. Because excessive WTR application can induce P deficiency in crops, effective application rates and methods remain an area of intense research. Removal of other potential environmental contaminants [ClO4-, Se(+IV and +VI), As(+III and +V), and Hg] by WTR has been documented, suggesting potential use of WTR in environmental remediation. Although the creation of Al plant toxicity and enhanced Al leaching are concerns expressed by researchers, these effects are minimal at circumneutral soil pH conditions. Radioactivity, trace element levels, and enhanced Mn leaching have also been cited as potential problems in WTR usage as a soil supplement. However, these issues can be managed so as not to limit the beneficial use of WTR in controlling off-site P losses to sensitive water bodies or reducing soil-extractable P concentrations.     

Controlled application rate of water treatment residual for agronomic and environmental benefits

Water treatment residuals (WTR) are useful soil amendments to control excessive soluble phosphorus (P) in soils, but indiscriminate additions can result in inadequate control or excessive immobilization of soluble P, leading to crop deficiencies. We evaluated the influence of application rates of an Al-WTR and various P-sources on plant yields, tissue P concentrations, and P uptake and attempted to identify a basis for determining WTR application rates. Bahiagrass (paspalum notatum Fluggae) was grown in a P-deficient soil amended with four P-sources at two application levels (N- and P-based rates) and three WTR rates (0, 10, and 25 g kg(-1) oven dry basis) in a glasshouse pot experiment. The glasshouse results were compared with data from a 2-yr field experiment with similar treatments that were surface applied to an established bahiagrass. Soil P storage capacity (SPSC) values increased with application rate of WTR, and the increase varied with sources of P applied. Soil soluble P concentrations increased as SPSC was reduced, and a change point was identified at 0 mg kg(-1) SPSC in the glasshouse and the field studies. A change point was identified in the bahiagrass yields at a tissue P concentration of 2.0 g kg(-1), corresponding to zero SPSC. Zero SPSC was shown to be an agronomic threshold above which yields and P concentrations of plants declined and below which there is little or no yield response to increased plant P concentrations. Applying P-sources at N-based rates, along with WTR sufficient to give SPSC value of 0 mg kg(-1) SPSC, enhanced the environmental benefits (reduced P loss potential) without negative agronomic impacts.     

Solid phosphorus phase in aluminum- and iron-treated biosolids

Stabilization of phosphorus (P) in sewage sludge (biosolids) to reduce water-soluble P concentrations is essential for minimizing P loss from amended soils and maximizing the capacity of the soil to safely serve as an outlet for this waste material. The chemical form at which P is retained in biosolids stabilized by Al(2)(SO(4))(3) x 18H(2)O (alum) or FeSO(4) x 7H(2)O (FeSul) was investigated by scanning electron microscopy (SEM) equipped with energy-dispersive X-ray elemental spectrometry (EDXS) and by X-ray diffraction (XRD). Both treatments resulted in the formation of a Ca-P phase, probably brushite. Phosphorus was further retained in the alum-treated biosolids by precipitation of an Al-P phase with an Al/P molar ratio of about 1:1, while in the FeSul-treated biosolids, P was retained by both precipitation with Fe/P molar ratios of 1:1 or 1.5:1, and by adsorption onto newly formed Fe hydroxides exhibiting an Fe/P molar ratio of up to 11:1. All of these mechanisms efficiently reduced P solubility and are crucial in biosolids environmentally safe agronomic beneficial use for this waste product; however, each P phase formed may react differently in the amended soil, depending on soil properties. Thus, the proper P stabilization method would depend on the target soil.     

An alum-based water treatment residual can reduce extractable phosphorus concentrations in three phosphorus-enriched coastal plain soils

The accumulation of excess soil phosphorus (P) in watersheds under intensive animal production has been linked to increases in dissolved P concentrations in rivers and streams draining these watersheds. Reductions in water dissolved P concentrations through very strong P sorption reactions may be obtainable after land application of alum-based drinking water treatment residuals (WTRs). Our objectives were to (i) evaluate the ability of an alum-based WTR to reduce Mehlich-3 phosphorus (M3P) and water-soluble phosphorus (WSP) concentrations in three P-enriched Coastal Plain soils, (ii) estimate WTR application rates necessary to lower soil M3P levels to a target 150 mg kg(-1) soil M3P concentration threshold level, and (iii) determine the effects on soil pH and electrical conductivity (EC). Three soils containing elevated M3P (145-371 mg kg(-1)) and WSP (12.3-23.5 mg kg(-1)) concentrations were laboratory incubated with between 0 and 6% WTR (w w(-1)) for 84 d. Incorporation of WTR into the three soils caused a near linear and significant reduction in soil M3P and WSP concentrations. In two soils, 6% WTR application caused a soil M3P concentration decrease to below the soil P threshold level. An additional incubation on the third soil using higher WTR to soil treatments (10-15%) was required to reduce the mean soil M3P concentration to 178 mg kg(-1). After incubation, most treatments had less than a half pH unit decline and a slight increase in soil EC values suggesting a minimal impact on soil quality properties. The results showed that WTR incorporation into soils with high P concentrations caused larger relative reductions in extractable WSP than M3P concentrations. The larger relative reductions in the extractable WSP fraction suggest that WTR can be more effective at reducing potential runoff P losses than usage as an amendment to lower M3P concentrations.     

Phosphorus retention mechanisms of a water treatment residual

Water treatment residuals (WTRs) are a by-product of municipal drinking water treatment plants and can have the capacity to adsorb tremendous amounts of P. Understanding the WTR phosphorus adsorption process is important for discerning the mechanism and tenacity of P retention. We studied P adsorbing mechanism(s) of an aluminum-based [Al2(SO4)3 x 14H2O] WTR from Englewood, CO. In a laboratory study, we shook mixtures of P-loaded WTR for 1 to 211 d followed by solution pH analysis, and solution Ca, Al, and P analysis via inductively coupled plasma atomic emission spectroscopy. After shaking periods, we also examined the solids fraction by X-ray diffraction (XRD) and electron microprobe analysis using wavelength dispersive spectroscopy (EMPA-WDS). The shaking results indicated an increase in pH from 7.2 to 8.2, an increase in desorbed Ca and Al concentrations, and a decrease in desorbed P concentration. The pH and desorbed Ca concentration increases suggested that CaCO3 controlled Ca solubility. Increased desorbed Al concentration may have been due to Al(OH)4 formation. Decreased P content, in conjunction with the pH increase, was consistent with calcium phosphate formation or precipitation. The system appeared to be undersaturated with respect to dicalcium phosphate (DCP; CaHPO4) and supersaturated with respect to octacalcium phosphate [OCP; Ca4H(PO4)3 x 2.5H2O]. The Ca and Al increases, as well as OCP formation, were supported by MINTEQA2 modeling. The XRD and EMPA-WDS results for all shaking times, however, suggested surface P chemisorption as an amorphous Al-P mineral phase.     

Runoff phosphorus losses from surface-applied biosolids

Runoff losses of dissolved and particulate phosphorus (P) may occur when rainfall interacts with manures and biosolids spread on the soil surface. This study compared P levels in runoff losses from soils amended with several P sources, including 10 different biosolids and dairy manure (untreated and treated with Fe or Al salts). Simulated rainfall (71 mm h(-1)) was applied until 30 min of runoff was collected from soil boxes (100 x 20 x 5 cm) to which the P sources were surfaced applied. Materials were applied to achieve a common plant available nitrogen (PAN) rate of 134 kg PAN ha(-1), resulting in total P loading rates from 122 (dairy manure) to 555 (Syracuse N-Viro biosolids) kg P ha(-1). Two biosolids produced via biological phosphorus removal (BPR) wastewater treatment resulted in the highest total dissolved phosphorus (13-21.5 mg TDP L(-1)) and total phosphorus (18-27.5 mg TP L(-1)) concentrations in runoff, followed by untreated dairy manure that had statistically (p = 0.05) higher TDP (8.5 mg L(-1)) and TP (10.9 mg L(-1)) than seven of the eight other biosolids. The TDP and TP in runoff from six biosolids did not differ significantly from unamended control (0.03 mg TDP L(-1); 0.95 mg TP L(-1)). Highest runoff TDP was associated with P sources low in Al and Fe. Amending dairy manure with Al and Fe salts at 1:1 metal-to-P molar ratio reduced runoff TP to control levels. Runoff TDP and TP were not positively correlated to TP application rate unless modified by a weighting factor reflecting the relative solubility of the P source. This suggests site assessment indices should account for the differential solubility of the applied P source to accurately predict the risk of P loss from the wide variety of biosolids materials routinely land applied.     

Runoff and leachate losses of phosphorus in a sandy Spodosol amended with biosolids

Florida Spodosols are sandy, inherently low in Fe- and Al-based minerals, and sorb phosphorus (P) poorly. We evaluated runoff and leachate P losses from a typical Florida Spodosol amended with biosolids and triple superphosphate (TSP). Phosphorus losses were evaluated with traditional indoor rainfall simulations but used a double-deck box arrangement that allowed leaching and runoff to be determined simultaneously. Biosolids (Lakeland, OCUD, Milorganite, and Disney) represented contrasting values of total P, percent water-extractable P (PWEP), and percentage of solids. All P sources were surface applied at 224 kg P ha(-1), representing a soil P rate typical of N-based biosolids application. All biosolids-P sources lost less P than TSP, and leachate-P losses generally dominated. For Lakeland-amended soil, bioavailable P (BAP) was mainly lost by runoff (81% of total BAP losses). This behavior was due to surface sealing and drying after application of the slurry (31 g kg(-1) solids) material. For all other P sources, BAP losses in leachate were much greater than in runoff, representing 94% of total BAP losses for TSP, 80% for Milorganite, 72% for Disney, and 69% for OCUD treatments. Phosphorus leaching can be extreme and represents a great concern in many coarse-textured Florida Spodosols and other coastal plain soils with low P-sorption capacities. The PWEP values of P sources were significantly correlated with total P and BAP losses in runoff and leachate. The PWEP of a source can serve as a good indicator of potential P loss when amended to sandy soils with low P-retention capacities.     

Phosphorus forms in biosolids-amended soils and losses in runoff: effects of wastewater treatment process

Continuous addition of municipal biosolids to soils based on plant nitrogen (N) requirements can cause buildup of soil phosphorus (P) in excess of crop requirements; runoff from these soils can potentially contribute to nonpoint P pollution of surface waters. However, because biosolids are often produced using lime and/or metal salts, the potential for biosolids P to cause runoff P losses can vary with wastewater treatment plant (WWTP) process. This study was conducted to determine the effect of wastewater treatment process on the forms and amounts of P in biosolids, biosolids-amended soils, and in runoff from biosolids-amended soils. We amended two soil types with eight biosolids and a poultry litter (PL) at equal rates of total P (200 kg ha(-1); unamended soils were used as controls. All biosolids and amended soils were analyzed for various types of extractable P, inorganic P fractions, and the degree of P saturation (acid ammonium oxalate method). Amended soils were placed under a simulated rainfall and all runoff was collected and analyzed for dissolved reactive phosphorus (DRP), iron-oxide-coated filter paper strip-extractable phosphorus (FeO-P), and total phosphorus (EPA3050 P). Results showed that biosolids produced with a biological nutrient removal (BNR) process caused the highest increases in extractable soil P and runoff DRP. Alternatively, biosolids produced with iron only consistently had the lowest extractable P and caused the lowest increases in extractable soil P and runoff DRP when added to soils. Differences in soil and biosolids extractable P levels as well as P runoff losses were related to the inorganic P forms of the biosolids.     

Assessing effects of aerobic and anaerobic conditions on phosphorus sorption and retention capacity of water treatment residuals

Water treatment residuals (WTRs) are the by-products of drinking water clarification processes, whereby chemical flocculants such as alum or ferric chloride are added to raw water to remove suspended clay particles, organic matter and other materials and impurities. Previous studies have identified a strong phosphorus (P) fixing capacity of WTRs which has led to experimentation with their use as P-sorbing materials for controlling P discharges from agricultural and forestry land. However, the P-fixing capacity of WTRs and its capacity to retain sorbed P under anaerobic conditions have yet to be fully demonstrated, which is an issue that must be addressed for WTR field applications. This study therefore examined the capacity of WTRs to retain sorbed P and sorb further additional P from aqueous solution under both aerobic and anaerobic conditions. An innovative, low cost apparatus was constructed and successfully used to rapidly establish anoxic conditions in anaerobic treatments. The results showed that even in treatments with initial solution P concentrations set at 100 mg l(-1), soluble reactive P concentrations rapidly fell to negligible levels (due to sorption by WTRs), while total P (i.e. dissolved + particulate and colloidal P) was less than 3 mg l(-1). This equated to an added P retention rate of >98% regardless of anaerobic or aerobic status, indicating that WTRs are able to sorb and retain P in both aerobic and anaerobic conditions.     

Spatial variation of soil phosphorus within a drainage ditch network

Agricultural drainage ditches serve as P transport pathways from fields to surface waters. Little is known about the spatial variation of P at the soil-water interface within ditch networks. We quantified the spatial variation of surficial (0-5 cm) soil P within vegetated agricultural ditches on a farm in Princess Anne, MD with an approximately 30-yr history of poultry litter application. Ditch soils from 10 ditches were sampled at 10-m intervals and analyzed for acid ammonium oxalate-extractable P, Fe, Al (P(ox), Fe(ox), Al(ox)), and pH. These variables were spatially autocorrelated. Oxalate-P (min = 135 mg kg(-1), max = 6919 mg kg(-1), mean = 700 mg kg(-1)) exhibited a high standard deviation across the study area (overall 580 mg kg(-1)) and within individual ditches (maximum 1383 mg kg(-1)). Several ditches contained distinct areas of high P(ox), which were associated with either point- or nonpoint-P sources. Phosphorus was correlated with Al(ox) or Fe(ox) within specific ditches. Across all ditches, Al(ox) (r = 0.80; p < 0.001) was better correlated with P(ox) than was Fe(ox) (r = 0.44; p < 0.001). The high level of spatial variation of soil P observed in this ditch network suggests that spatially distributed sampling may be necessary to target best management practices and to model P transport and fate in ditch networks.     

Phosphorus in Hawaiian kikuyugrass pastures and potential phosphorus release to water

Pasture systems in Hawaii are based primarily on kikuyugrass (Pennisetum clandestinum Hochst. ex Chiov.). Relationships among kikuyugrass P concentration, animal P requirements, and various soil P determinations are needed to help identify source areas for implementing pasture management strategies to limit P loss via overland flow. A total of 51 rotationally stocked kikuyugrass pastures (>20 yr old) with contrasting soil chemical properties were sampled. A satisfactory predictive relationship between modified-Truog (MT)-extractable phosphorus (P(MT)) and dissolved (<0.45-mum pore diameter), molybdate-reactive phosphorus (DRP) desorbed from soil in a water extract (DRP(WE)) was found when 0- to 4-cm-depth data for the soil orders with medium to high DRP(WE) (two Mollisols and an Inceptisol) were pooled separately from those with low DRP(WE) (five Andisols, three Ultisols, and an Oxisol). The oxalate phosphorus saturation index (PSI(ox)) procedure was the best predictor of DRP(WE) across soil orders when oxalate-extractable molybdate-reactive phosphorus (RP(ox)) was used to calculate PSI(ox) (PSI(ox)RP) rather than when total oxalate-extractable phosphorus (TP(ox)) was used (PSI(ox)TP). There was little DRP(WE) until PSI(ox)RP exceeded 6% or PSI(ox)TP exceeded 8%. A more empirical dilute-acid phosphorus saturation index (PSI(MT)) was also calculated using P(MT) and MT-extractable iron (Fe(MT)) and aluminum (Al(MT)). The PSI(MT) procedure showed some utility in predicting DRP(WE), was positively related to the PSI(ox) procedures, and can be more readily performed in agronomic soil testing laboratories than PSI(ox). The present research suggests that while Hawaiian kikuyugrass pastures tend to be sufficient to high in forage P, potential soil P release to water only appeared to be a possible environmental concern for the Mollisol and Inceptisol sites.