Removal of arsenic from groundwater by granular titanium dioxide adsorbent

A novel granular titanium dioxide (TiO2) was evaluated for the removal of arsenic from groundwater. Laboratory experiments were carried out to investigate the adsorption capacity of the adsorbent and the effect of anions on arsenic removal. Batch experimental results showed that more arsenate [As(V)] was adsorbed on TiO2 than arsenite [As(III)] in US groundwater at pH 7.0. The adsorption capacities for As(V) and As(III) were 41.4 and 32.4 mgg(-1) TiO2, respectively. However, the adsorbent had a similar adsorption capacity for As(V) and As(III) (approximately 40 mgg(-1)) when simulated Bangladesh groundwater was used. Silica (20 mgl(-1)) and phosphate (5.8 mgl(-1)) had no obvious effect on the removal of As(V) and As(III) by TiO2 at neutral pH. Point-of-entry (POE) filters containing 3 l of the granular adsorbent were tested for the removal of arsenic from groundwater in central New Jersey, USA. Groundwater was continuously passed through the filters at an empty bed contact time (EBCT) of 3 min. Approximately 45,000 bed volumes of groundwater containing an average of 39 microgl(-1) of As(V) was treated by the POE filter before the effluent arsenic concentration increased to 10 microgl(-1). The total treated water volumes per weight of adsorbent were about 60,000 l per 1 kg of adsorbent. The field filtration results demonstrated that the granular TiO2 adsorbent was very effective for the removal of arsenic in groundwater.     

Fluoride removal performance of a novel Fe-Al-Ce trimetal oxide adsorbent

A trimetal oxide was developed as a fluoride adsorbent by coprecipitation of Fe(II), Al(III) and Ce(IV) salt solutions with a molar ratio of 1:4:1 under alkaline condition. The material retained amorphous structure and maintained relatively stable fluoride adsorption performance at calcination temperatures lower than 600 degrees C. The optimum pH range for fluoride adsorption was 6.0-6.5 and the adsorbent also showed high defluoridation ability around pH 5.5-7.0, which is preferable for actual application. A high fluoride adsorption capacity of 178 mg g(-1) was acquired under an equilibrium fluoride concentration of 84.5 mg l(-1), adsorbent dose of 150 mg l(-1) and pH 7.0. The adsorption isotherm could be better described by the two-site Langmuir model than the one-site model, suggesting the existence of two types of active sites on the adsorbent surface. Coexistence of high concentrations of phosphate or arsenate only led to partial inhibition of fluoride adsorption, which further suggests the existence of heterogeneous adsorption sites. Sulfate and chloride did not affect fluoride adsorption, and nitrate influenced it only when the concentration of NO(3)(-)-N exceeded 50 mg l(-1). A high desorption efficiency of 97% was achieved by treating fluoride loaded Fe-Al-Ce oxide with NaOH solution at pH 12.2. A column experiment using the adsorbent fabricated into 1mm pellets was performed at an initial fluoride concentration of 5.5 mg l(-1), space velocity of 5h(-1) and pH of 5.8, and 2240 bed volumes were treated with the effluent fluoride under 1.0 mg l(-1).     

Adsorption and removal of As(V) and As(III) using Zr-loaded lysine diacetic acid chelating resin

An adsorption process for the removal of As(V) and As(III) was evaluated under various conditions using zirconium(IV) loaded chelating resin (Zr-LDA) with lysine-Nalpha,Nalpha diacetic acid functional groups. Arsenate ions strongly adsorbed in the pH range from 2 to 5, while arsenite was adsorbed between pH 7 and 10.5. The sorption mechanism is an additional complexation between arsenate or arsenite and Zr complex of LDA. Adsorption isotherm data could be well interpreted by Langmuir equation for As(V) at pH 4 and As(III) at pH 9 with a binding constant 227.93 and 270.47 dm3 mol(-1) and capacity constant 0.656 and 1.1843 mmol g(-1), respectively. Regeneration of the resin was carried out for As(V) using 1 M NaOH. Six adsorption/desorption cycles were performed without significant decrease in the uptake performance. Column adsorption studies showed that the adsorption of As(V) is more favorable compared to As(III), due to the faster kinetics of As(V) compared to As(III). Influence of the coexisting ions on the adsorption of As(V) and As(III) was studied. The applicability of the method for practical water samples was studied.     

Arsenic(V) removal from aqueous solutions using an anion exchanger derived from coconut coir pith and its recovery

The performance of a new anion exchanger (AE) prepared from coconut coir pith (CP), for the removal of arsenic(V) [As(V)] from aqueous solutions was evaluated in this study. The adsorbent (CP-AE) carrying dimethylaminohydroxypropyl weak base functional group was synthesized by the reaction of CP with epichlorohydrin and dimethylamine followed by treatment of hydrochloric acid. IR spectroscopy results confirm the presence of -NH(+)(CH(3))(2)Cl(-) group in the adsorbent. XRD studies confirm the decrease of crystallinity in CP-AE compared to CP, and it favours the protrusion of the functional group into the aqueous medium. Batch experiments were conducted to examine the efficiency of the adsorbent on As(V) removal. Maximum removal of 99.2% was obtained for an initial concentration of 1 mgl(-1) As(V) at pH 7.0 and an adsorbent dose of 2 gl(-1). The kinetics of sorption of As(V) onto CP-AE was described using the pseudo-second-order model. The equilibrium isotherms were determined for different temperatures and the results were analysed using the Langmuir equation. The temperature dependence indicates an exothermic process. Utility of the adsorbent was tested by removing As(V) from simulated groundwater. Regeneration studies were performed using 0.1N HCl. Batch adsorption-desorption studies illustrate that CP-AE could be used to remove As(V) from ground water and other industrial effluents.     

Waste Fe(III)/Cr(III) hydroxide as adsorbent for the removal of Cr(VI) from aqueous solution and chromium plating industry wastewater

Fe(III)/Cr(III) hydroxide, a waste material from the fertilizer industry, has been used for the adsorption of Cr(VI) from aqueous solution, over a range of initial metal ion concentrations (5-30 mg litre(-1)), agitation times (1-180 min), adsorbent dosages (100-1200 mg per 50 ml), temperatures (24, 29 and 38 degrees C) and pH values (4.5-10). The adsorption of Cr(VI) increased with the initial concentration of Cr(VI) and with temperature. The process of uptake follows both the Langmuir and the Freundlich isotherm models. The applicability of Lagergren and empirical kinetic models has also been investigated. Almost quantitative removal of Cr(VI) at 10 mg litre(-1) in a 50-ml solution by 500 mg of adsorbent was found at an equilibrium pH of 5.6. The efficiency of chromium removal was also tested using wastewater from the chromium plating industry.     

Evaluation of the multiple-ion competition in the adsorption of As(V) onto reclaimed iron-oxide coated sands by fractional factorial design

This study describes the competitive effects of selected ions and natural organic matter on As(V) removal using reclaimed iron-oxide coated sands (RIOCS) in the single- and multi-ion systems. A 2(7-3) factional factorial experimental design (FFD) was employed for screening main competitive factors in this adsorption process. As a result, the inhibitive competition effects of the anions on As(V) removal in the single ion system were in the following sequence: PO(4)(3-)>SiO(3)(2-)>HCO(3)(-)>humic acid (HA)>SO(4)(2-)>Cl(-), whereas the cation Ca(2+) was observed to enhance the As(V) removal. In addition, the optimum initial pH for As(V) removal in single-ion system was 5. Based on the estimates of major effects and interactions from the FFD, PO(4)(3-), SiO(3)(2-), Ca(2+) and HA were important factors on As(V) removal in the multi-ion system. The promoters for the As(V) removal were found to be Ca(2+) and, to a lesser extent, SO(4)(2-). The competitive effects of these ions on As(V) removal were in the order of PO(4)(3-), SiO(3)(2-), HA, HCO(3)(-), and Cl(-). In the single ion system, the efficiencies of As(V) removal range from 75% to 96%, much higher than those in the multi-ion system (44%) at the initial pH 5. Clearly, there were some complex anion interactions in the multi-ion system. To promote the removal of As(V) by RIOCS, it is proposed to lower the pH in the single-ion system, while in the multi-ion system, the increase of the Ca(2+) concentration, or decreases of PO(4)(3-), SiO(3)(2-) and HA concentrations is suggested.     

Evaluation of boron removal from water by hydrotalcite-like compounds

Layered double hydroxides (LDHs) or hydrotalcite (HT)-like compounds with different kinds of metal ions (Mg-Al and Mg-Fe) in the brucite-like sheets were prepared and their adsorption properties were studied in the boron removal from aqueous solution under laboratory conditions. The hydrotalcites were synthesized by the coprecipitation method and were characterized by chemical analyses, X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FTIR) and specific surface area measurements (BET). The affinity of these materials with a mixture of B(OH)(3) and B(OH)(4)(-) was studied as a function of contact time, initial pH of the solutions, HT quantity and B concentration (adsorption isotherms). It was found that 120 min is enough time for the equilibrium state to be reached in boron adsorption. Boron removal was independent of the initial pH of the solutions because of the high buffering capacity of the LDHs. On the other hand, the adsorption capacity increases with increasing the adsorbent quantity. The adsorption isotherms, described by the Langmuir model, are of L-type, suggesting that B(OH)(4)(-) is adsorbed preferentially on HT-like materials. Besides, Mg-Al hydrotalcites showed higher adsorption capacity than Mg-Fe. We proposed that in Mg-Al hydrotalcites, the boron removal occurs by both adsorption on external surface and ion exchange, whereas for Mg-Fe it occurs only by surface adsorption. After treatment of a solution containing 5.2 mgBl(-1) with Mg-Al hydrotalcites the final boron concentration reached the recommended limit by WHO for drinking water (0.5 mgl(-1)).     

Thermodynamic and kinetic studies of As(V) removal from water by zirconium oxide-coated marine sand

Arsenic contamination of groundwater is a major threat to human beings globally. Among various methods available for arsenic removal, adsorption is fast, inexpensive, selective, accurate, reproducible and eco-friendly in nature. The present paper describes removal of arsenate from water on zirconium oxide-coated sand (novel adsorbent). In the present work, zirconium oxide-coated sand was prepared and characterised by infrared and X-ray diffraction techniques. Batch experiments were performed to optimise different adsorption parameters such as initial arsenate concentration (100–1,000 μg/L), dose (1–8 g/L), pH of the solution (2–14), contact time (15–150 min.), and temperature (20, 30, 35 and 40 °C). The experimental data were analysed by Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. Furthermore, thermodynamic and kinetic parameters were evaluated to know the mode of adsorption between ZrOCMS and As(V). The maximum removal of arsenic, 97 %, was achieved at initial arsenic concentration of 200 μg/L, after 75 min at dosage of 5.0 g/L, pH?7.0 and 27?±?2 °C. For 600 μg/L concentration, the maximum Langmuir monolayer adsorption capacity was found to be 270 μg/g at 35 °C. Kinetic modelling data indicated that adsorption process followed pseudo-second-order kinetics. The mechanism is controlled by liquid film diffusion model. Thermodynamic parameter, ΔH°, was ?57.782, while the values of ΔG° were ?9.460, ?12.183, ?13.343 and ?13.905 kJ/mol at 20, 30, 35 and 40 °C, respectively, suggesting exothermic and spontaneous nature of the process. The change in entropy, ΔS°?=??0.23 kJ/mol indicated that the entropy decreased due to adsorption of arsenate ion onto the solid adsorbent. The results indicated that the reported zirconium oxide-coated marine sand (ZrOCMS) was good adsorbent with 97 % removal capacity at 200 μg/L concentration. It is interesting to note that the permissible limit of arsenic as per World Health Organization is 10 μg/L, and in real situation, this low concentration can be achieved through this adsorbent. Besides, the adsorption capacity showed that this adsorbent may be used for the removal of arsenic from any natural water resource.     

Arsenic sorption by red mud-modified biochar produced from rice straw

Red mud-modified biochar (RM-BC) has been produced to be utilized as a novel adsorbent to remove As because it can effectively combine the beneficial features of red mud (rich metal oxide composition and porous structure) and biochar (large surface area and porous structure properties). SEM-EDS and XRD analyses demonstrated that red mud had loaded successfully on the surface of biochar. With the increasing of pH in solution, arsenate (As(V)) adsorption on RM-BC decreased while arsenite (As(III)) increased. Arsenate adsorption kinetics process on RM-BC fitted the pseudo-second-order model, while that of As(III) favored the Elovich model. All sorption isotherms produced superior fits with the Langmuir model. RM-BC exhibited improved As removal capabilities, with a maximum adsorption capacity (Q_max) for As(V) of 5923 μg g^?1, approximately ten times greater than that of the untreated BC (552.0 μg g^?1). Furthermore, it has been indicated that the adsorption of As(V) on RM-BC may be strongly associated with iron oxides (hematite and magnetite) and aluminum oxides (gibbsite) by X-ray absorption near-edge spectroscopy (XANES), which was possibly because of surface complexation and electrostatic interactions. RM-BC may be used as a valuable adsorbent for removing As in the environment due to the waste materials being relatively abundant.     

溴化十六烷基吡啶改性沸石对水中甲基橙的吸附

采用溴化十六烷基吡啶(CPB)对天然沸石进行改性制备得到了CPB改性沸石,通过批量吸附实验考察了CPB改性沸石对水中阴离子染料甲基橙的去除作用。结果表明,天然沸石对水中甲基橙的吸附能力很差,而CPB改性沸石则可以有效吸附去除水中的甲基橙。CPB改性沸石对水中甲基橙的吸附能力随CPB负载量的增加而增加,CPB负载量最大的改性沸石对水中甲基橙的吸附能力最强。双分子层CPB改性沸石对水中甲基橙的去除率随吸附剂投加量的增加而增加,而CPB改性沸石对水中甲基橙的单位吸附量则随吸附剂投加量的增加而降低。双分子层CPB改性沸石对水中甲基橙的吸附平衡数据可以采用Langmuir等温吸附模型加以描述。根据Langmuir模型计算得到的CPB负载量为341 mmol/(kg沸石)的双分子层CPB改性沸石对水中甲基橙的最大吸附容量为63.7 mg/g(303 K和pH 7)。准二级动力学模型适合用于描述双分子层CPB改性沸石对水中甲基橙的吸附动力学过程。pH和反应温度对双分子层CPB改性沸石吸附水中甲基橙的影响较小。以上结果说明,双分子层CPB改性沸石适合作为一种吸附剂用于去除废水中的甲基橙。     

Removal of nickel (II) from aqueous solutions using marine macroalgae as the sorbing biomass

In the present study biosorption technique, the passive accumulation of metals by biomass, is used for the removal of nickel from aqueous medium. The brown algae, Sargassum sp., in its natural and acid treated forms are used as a low cost sorbent. The adsorption characteristics of nickel on Sargassum sp. are evaluated as a function of time, pH, adsorbent dosage and initial concentration of nickel. The equilibrium adsorption data are fitted to Freundlich and Langmuir adsorption isotherm models and the model parameters are evaluated. Both the models represent the experimental data satisfactorily. The adsorption follows Lagergren first order kinetic model. The monolayer adsorption capacities of natural and acid treated forms of algae as obtained from Langmuir adsorption model are found to be 181 and 250mg g(-1) respectively.     

Evaluating of arsenic(V) removal from water by weak-base anion exchange adsorbents

Arsenic contamination of groundwater has been called the largest mass poisoning calamity in human history and creates severe health problems. The effective adsorbents are imperative in response to the widespread removal of toxic arsenic exposure through drinking water. Evaluation of arsenic(V) removal from water by weak-base anion exchange adsorbents was studied in this paper, aiming at the determination of the effects of pH, competing anions, and feed flow rates to improvement on remediation. Two types of weak-base adsorbents were used to evaluate arsenic(V) removal efficiency both in batch and column approaches. Anion selectivity was determined by both adsorbents in batch method as equilibrium As(V) adsorption capacities. Column studies were performed in fixed-bed experiments using both adsorbent packed columns, and kinetic performance was dependent on the feed flow rate and competing anions. The weak-base adsorbents clarified that these are selective to arsenic(V) over competition of chloride, nitrate, and sulfate anions. The solution pH played an important role in arsenic(V) removal, and a higher pH can cause lower adsorption capacities. A low concentration level of arsenic(V) was also removed by these adsorbents even at a high flow rate of 250–350 h^?1. Adsorbed arsenic(V) was quantitatively eluted with 1 M HCl acid and regenerated into hydrochloride form simultaneously for the next adsorption operation after rinsing with water. The weak-base anion exchange adsorbents are to be an effective means to remove arsenic(V) from drinking water. The fast adsorption rate and the excellent adsorption capacity in the neutral pH range will render this removal technique attractive in practical use in chemical industry.     

活化赤泥的除氟性能

以成本低的铝工业废矿渣（赤泥）为原材料,通过高温煅烧和酸化处理对赤泥进行活化,制备了除氟吸附剂。研究了反应时间、投加量、初始氟浓度、溶液温度、共存阴离子和pH值对活化赤泥除氟效果的影响。结果表明,接触反应时间为18 h时,吸附接近平衡。活化赤泥对氟离子的吸附符合Lagergren二级吸附动力学方程。另外,初始浓度越高,吸附容量越大。与Freundlich相比,Langmuir吸附等温模型可以更好地描述氟离子的吸附特性,最大吸附量可达2.71 mg/g。SO24-、Cl-和NO3-存在时（〈1 000 mg/L）,对氟离子的吸附几乎没有影响,然而,HCO3-、PO34-和氟离子共存时,会对氟吸附造成不利影响。活化赤泥在pH值3.5～11.0时,具有较好的吸附稳定性。活化赤泥是一种吸附容量高、性能稳定的环境友好型除氟材料,具有应用潜力。     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

Removal of arsenic(III,V) by a granular Mn-oxide-doped Al oxide adsorbent: surface characterization and performance

In order to remove arsenic (As) from contaminated water, granular Mn-oxide-doped Al oxide (GMAO) was fabricated using the compression method with the addition of organic binder. The analysis results of XRD, SEM, and BET indicated that GMAO was microporous with a large specific surface area of 54.26 m^2/g, and it was formed through the aggregation of massive Al/Mn oxide nanoparticles with an amorphous pattern. EDX, mapping, FTIR, and XPS results showed the uniform distribution of Al/Mn elements and numerous hydroxyl groups on the adsorbent surface. Compression tests indicated a satisfactory mechanical strength of GMAO. Batch adsorption results showed that As(V) adsorption achieved equilibrium faster than As(III), whereas the maximum adsorption capacity of As(III) estimated from the Langmuir isotherm at 25 °C (48.52 mg/g) was greater than that of As(V) (37.94 mg/g). The As removal efficiency could be maintained in a wide pH range of 3~8. The presence of phosphate posed a significant adverse effect on As adsorption due to the competition mechanisms. In contrast, Ca²⁺ and Mg²⁺ could favor As adsorption via cation-bridge involvement. A regeneration method was developed by using sodium hydroxide solution for As elution from saturated adsorbents, which permitted GMAO to keep over 75% of its As adsorption capacity even after five adsorption–regeneration cycles. Column experiments showed that the breakthrough volumes for the treatment of As(III)-spiked and As(V)-spiked water (As concentration = 100 μg/L) were 2224 and 1952, respectively. Overall, GMAO is a potential adsorbent for effectively removing As from As-contaminated groundwater in filter application.

     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Removal of As(III) and As(V) using iron-rich sludge produced from coal mine drainage treatment plant

To test the feasibility of the reuse of iron-rich sludge (IRS) produced from a coal mine drainage treatment plant for removing As(III) and As(V) from aqueous solutions, we investigated various parameters, such as contact time, pH, initial As concentration, and competing ions, based on the IRS characterization. The IRS consisted of goethite and calcite, and had large surface area and small particles. According to energy dispersive X-ray spectroscopy mapping results, As was mainly removed by adsorption onto iron oxides. The adsorption kinetic studies showed that nearly 70 % adsorption of As was achieved within 1 h, and the pseudo-second-order model well explained As sorption on the IRS. The adsorption isotherm results agreed with the Freundlich isotherm model, and the maximum adsorption capacities for As(III) and As(V) were 66.9 and 21.5 mg/g, respectively, at 293 K. In addition, the adsorption showed the endothermic character. At high pH or in the presence of phosphate, the adsorption of As was decreased. When the desorption experiment was conducted to reuse the IRS, 85 % As was desorbed with 1.0 N NaOH. In the column experiment, adsorbed As in real acid mine drainage was 43 % of the maximum adsorbed amount of As in the batch test. These results suggested that the IRS is an effective adsorbent for As and can be effectively applied for the removal of As in water and wastewater.     

Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

Arsenic(III) removal by adsorption on sawdust carbon

Studies on the removal of As(III) by adsorption on sawdust and sawdust carbon have been carried out at room temperature (25 ± 1°C). The adsorption isotherm of As(III) on sawdust carbon was obtained in a batch reactor. The process of uptake follows the first-order adsorption rate expression and obeys the Langmuir and Freundlich model of adsorption. The mass transfer coefficients as a function of initial sorbate concentration have been determined. Parameters such as pH and absorbent dose were studied. Maximum adsorption capacity was observed at pH 7.0.     

Adsorption of arsenic(V) by activated carbon prepared from oat hulls

The efficiency of self-manufactured activated carbon (AC) produced from oat hulls in adsorbing arsenic(V) was tested in a batch reactor. The results indicated that the adsorptive capacity of AC was affected by initial pH value, with adsorption capacity decreasing from 3.09 to 1.57 mg As g(-1) AC when the initial pH values increased from 5 to 8. A modified linear driving force model conjugated with a Langmuir isotherm was created to describe the study's kinetics. The test results show that rapid adsorption and slow adsorption exist simultaneously when AC is used to remove arsenic(V).