市政污泥掺烧对生活垃圾焚烧设施烟气中污染物排放的影响

与生活垃圾协同焚烧是污泥处置中最有前景的处置方式,但其对焚烧烟气污染物排放的影响尚未明确。利用生活垃圾焚烧炉开展生活垃圾协同处置市政污泥的试验,研究掺烧5%、10%和15%的市政污泥时焚烧烟气中酸性气体、烟尘、重金属和二噁英等的排放特征。结果表明:与单独焚烧生活垃圾的对照组相比,在各掺烧比例下,烟气中SO_2、HCl、NO_x及烟尘有一定程度的增加,但均未超过GB18485—2014《生活垃圾焚烧污染控制标准》限值;Cu、Hg排放质量浓度明显下降,Cr、Cd波动下降,Pb在高掺烧比时仍远低于限值,Ni增长幅度小于15%;二噁英总量升高,但仍符合标准限值。因此,在掺烧比例不超过15%的情况下,焚烧烟气中污染物排放仍在安全可控范围。     

污泥掺烧对焚烧后固体废物污染物排放的影响

在佛山某生活垃圾焚烧发电厂开展生活垃圾掺烧市政污泥工业试验,分析5%、10%、15%的市政污泥掺烧对电厂焚烧后固体废物中重金属和二噁英排放的影响。结果表明,掺烧污泥使Cd在飞灰中的分布提高了40%以上,但其他重金属的分布特征仍主要受各自沸点的影响。焚烧固废中重金属含量受污泥的引入影响普遍不显著,飞灰中Cu浸出质量浓度上升20%,Ni、Pb、Hg、Cr的浸出质量浓度波动下降;炉渣中重金属浸出质量浓度波动较大。焚烧飞灰中总二噁英含量与污泥掺烧比例成负相关,且与投料中的Cl质量分数成正相关,与S质量分数成负相关。因此,低于15%的污泥掺烧比例不会显著提升焚烧固废中污染物排放浓度。     

城市垃圾掺烧搅拌设备电气控制系统设计

垃圾直接掺烧就是把分类后的可焚烧垃圾与煤按一定比例混合,进行高温焚烧,降低垃圾体积,减少污染。结合污泥处置的要求,设计了垃圾掺烧搅拌设备的电气控制系统。该电控系统可以实现垃圾计量、故障报警以及模式切换等功能,满足搅拌设备控制的各项性能指标,工艺达到环保要求。     

生活垃圾衍生燃料掺烧过程环境影响分析研究

通过在燃煤中掺混不同比例的垃圾衍生燃料(RDF)进行燃烧实验,测试了锅炉热工和调整锅炉运行工况后烟气污染物排放情况,同时实时监测厂界污染物排放情况。分析污染物排放浓度变化趋势,确定掺烧RDF的最佳比例,燃煤锅炉运行的最佳参数和技术要点。结果表明,在掺混RDF 10%~30%的比例时,对燃料的碳含量、硫含量、氮含量、灰分、水分和低位发热值均无不利影响,符合北京市关于使用低硫优质煤的标准。RDF掺混比例越高,锅炉热效率降低,比例为30%时,锅炉热效率在80%左右,同时在该比例以下,可以确保二恶英、氮氧化物、烟尘、二氧化硫等污染物达标排放,厂界大气污染物都在二级标准以内。     

燃煤电厂掺烧市政污泥工程大气污染分析

市政污泥与燃煤掺混在电厂锅炉内焚烧,实现污泥无害化、减量化、资源化处置是较好的方式。利用电厂做过功、不经处理无法直接利用的低品质蒸汽为热源,对污泥进行间接干化,干化后的污泥在燃煤锅炉内进行焚烧处理。污泥掺烧比率的增大会对大气污染物排放浓度产生一定的影响。在7.35%的污泥掺烧率内,随着污泥掺烧率的增大,SO2的排放浓度变化不大,NOx的排放浓度逐渐降低,烟粉尘的排放量有增大趋势,但是最终的排放浓度均在排放限值内。污泥与燃煤掺烧,重金属排放浓度并无较大改变,符合排放标准。     

预氧化浸水煤体表面结构变化及复燃特性*

为研究预氧化长期浸水煤体孔隙结构变化及贫氧复燃特性,以长焰煤原煤（RC）、浸水煤(S200)、预氧化200浸水煤(O200I200)、预氧化300浸水(O300I200)煤为研究对象,采用N2吸附、电镜扫描、热重实验手段,在21%,15%,10%,5%氧浓度下进行实验分析。结果表明:浸水后煤样比表面积增大,低温氧化最大质量变化率（DTG）较高,促进低温氧化过程煤氧复合反应;预氧化浸水煤样平均孔径增加,初始放热温度较小,总放热量增加,其中O200I200煤样热参数相对较大。随氧浓度增加,各煤样着火点温度减小,活化能增加,O200I200煤样的这2个参数较小;随氧浓度降低,煤样初始放热温度增加,最大放热量与总放热量减小。O200I200煤体孔隙较发达,锁水能力较强,持续升温后氧化能力较强,更易复燃。     

温度升高对湿地系统温室气体排放的影响

综述了湿地系统温室气体CO2、CH4和N2O的排放机制及温度升高对湿地系统温室气体排放影响的研究进展.温度升高使得湿地植物生长季节延长,促进湿地生态系统生产力的提高,影响湿地生态系统的稳定性.温度升高可改变湿地系统温室气体CO2、CH4和N2O排放的源汇转换,使温室气体排放增加,并对温度变化形成一种正反馈影响.温度升高使得湿地CO2排放增强,降低湿地土壤碳汇的能力,甚至转变为净碳源.温度升高可增加湿地CH4排放量,夏季温度升高对CH4排放通量没有明显影响.温度升高使湿地土壤硝化和反硝化作用增强,促进N2O的产生与排放,湿地成为N2O的排放源.同时,温度升高使得湿地水位降低、土壤水分减少,一定程度上约束了温室气体排放增加的强度.并对进一步的研究进行了展望.     

冻融交替过程对黑土中氧化亚氮释放特性的影响

通过人工模拟冻融过程,研究了不同冻融条件对黑土中N2O释放特性影响。结果表明,在含水量一定的前提下,黑土N2O的释放量随着施氮量的增加而增大,主要表现为,高氮处理的N2O排放通量比低氮处理增加了20.4%,常氮处理比低氮处理增加了16.1%,而高氮处理比常氮处理的增加了8.1%,两者差异并不显著。在施氮量一定的前提下,黑土中N2O的释放量随含水量的增大而增大。在含水量为15%、20%、25%的黑土中,N2O累积排放通量分别为2644、2930和3640μg·(m2·h)-1;土壤粒径也影响黑土中N2O的释放,但是影响并不显著;土壤酸化加剧黑土中N2O的释放。     

煤炭自燃倾向性试验研究及指标气体优选

通过对新鲜煤样和氧化煤样的热解实验,研究萍乡矿业集团某煤矿煤自燃发火特性,测定实验煤样在不同热解温度下O2,N2,CO,CO2等及其他碳氢化合物的浓度,具体分析了O2,CO,CO2,CH4,C3H6浓度随温度变化特性。在实验和研究的基础上,结合指标气体选择的一般原则,讨论了用于萍乡矿业集团某煤矿预测、预报煤炭自燃发火的指标气体,对提高煤炭早期自燃预测、预报的准确度和防止矿井火灾有重要指导意义。     

污水生化处理过程中N2O的产生特征研究进展

N2O是大气中重要的温室气体之一,而污水生化处理已被报道是导致N2O产生的潜在人为源之一。大量研究表明,污水生化处理过程中N2O主要产生于微生物的硝化和反硝化代谢过程中。从微生物学和生物化学反应角度,阐述了硝化和反硝化过程中N2O的生成机理,同时给出了几种典型污水处理工艺N2O的产生量和相关影响因素,并对A/A/O工艺中不同处理单元N2O的释放情况进行重点论述。研究发现,对于几种典型的污水处理工艺,由于工艺条件和主要影响因素的不同,N2O的释放量存在较大的差异;对于同一污水处理工艺,不同处理单元N2O的释放量也存在很大差别。污水处理厂中,好氧处理单元是N2O的主要排放单元,而在好氧单元中,DO质量浓度及NO2--N质量浓度是影响N2O释放量的主要因素。在综合分析硝化和反硝化过程N2O产生机理的基础上,进一步总结了污水生化处理过程中DO质量浓度、NO3-和NO2-质量浓度、pH值、C/N比、污泥龄等对N2O释放的影响。     

基于遗传算法的支持向量机预测有机物自燃点的研究

根据定量构效关系(QSPR)原理,研究自燃点(AIT)与其分子结构间的内在定量关系。以265种有机化合物作为样本集,随机选择238种作为训练集,27种作为测试集,用遗传算法(GA)进行变量选择,分别建立多元线性回归(MLR)模型和支持向量机(SVM)模型研究有机物的自燃点与其分子结构间的关系。通过分析,发现造成模型预测效果不佳的原因是试验数据本身存在问题。通过对2个模型的比较,结果为GA-SVM模型明显优于GA-MLR模型,说明自燃点与其分子结构间具有很强的非线性关系。     

Influence of ATD versus PMHS reference sensor inputs on computational brain response in frontal impacts to advanced combat helmet (ACH)

ABSTRACT

Objective: This study analyzed the influence of reference sensor inputs from anthropomorphic test devices (ATDs) versus postmortem human subjects (PMHSs) on simulations of frontal blunt impacts to the advanced combat helmet (ACH).

Methods: A rigid-arm pendulum was used to generate frontal impacts to ACHs mounted on ATDs and PMHS. An appropriately sized ACH was selected according to standard fitting guidelines. The National Operating Committee on Standards for Athletic Equipment (NOCSAE) head was selected for ATD tests due to shape features that enabled a realistic helmet fit. A custom procedure was used to mount a reference sensor internally near the center of gravity (CG) of the PMHS. Reference sensor data from the head CG were used as inputs for the Simulated Injury Monitor (SIMon). Brain responses were assessed with the cumulative strain damage measure set at 10%, or CSDM(10).

Results: Compared to ATD tests, PMHS tests produced 18.7% higher peak linear accelerations and 5.2% higher peak angular velocities. Average times to peak for linear accelerations were relatively similar between ATDs (5.5?ms) and PMHSs (5.8?ms). However, times to peak for angular velocities were higher by a factor of up to 3.4 for PMHSs compared to ATDs. Values for were also higher by a factor of up to 13.1 when PMHS inputs were used for SIMon.

Conclusions: The preliminary findings of this work indicate that small differences in ATD versus PMHS head kinematics could lead to large differences in strain-derived brain injury metrics such as CSDM.     

引气剂和聚丙烯纤维对高水材料性质的影响研究

为了改变高水材料的破坏特点,采用引气剂和聚丙烯纤维双掺对其进行改性。试验结果表明:随着引气剂掺量的增加,浆体的流动性逐渐降低,混合浆液失流时间延长,试块密度和单轴抗压强度逐渐减小;聚丙烯纤维的掺入,对浆体流动性、失流时间、引气率影响均较小。聚丙烯纤维最佳掺量为2 kg/m3,引气剂和聚丙烯纤维的掺入使硬化体的弹性模量略有减小,且使试块由脆性破坏转变为延性破坏,在保持整体不散的情况下,提高其压缩量。SEM观察表明:钙矾石在气泡壁上集中生成,聚丙烯纤维与基体的界面处有利于针状钙矾石的生成,从而使聚丙烯纤维更好地发挥增强增韧的作用。     

Nonlinear molecular based modeling of the flash point for application in inherently safer design

New chemical process design strategies utilizing computer-aided molecular design (CAMD) can provide significant improvements in process safety by designing chemicals with required target properties and the substitution of safer chemicals. An important aspect of this methodology concerns the prediction of properties given the molecular structure. This study utilizes one such emerging method for prediction of a hazardous property, flash point (FP), which is in the center of attention in safety studies. Using such a reliable data set comprising 1651 organic and inorganic chemicals, from 79 diverse material classes, and robust dynamic binary particle swarm optimization for the feature selection step resulted in the most efficient molecular features of the FP investigations. Apart from the simple yet precise five-parameter multivariate model, the FP nonlinear behavior was thoroughly investigated by a novel hybrid of particle swarm optimization and support vector regression. Besides, 195 missing experimental FPs of the DIPPR data set are predicted via the presented procedure.     

Automation design in advanced control rooms of the modernized nuclear power plants

This study evaluated the effects of levels of automation (LOAs) decisions in advanced control rooms of the modernized nuclear power plants. Following advancements in design of digitalized human–system interfaces (HSIs), the roles of human operators have changed significantly. Negative performance and safety consequences may occur as a result of these changes. These problems are viewed as the out-of-the-loop (OOTL) performance problems. This study conducted an experiment to compare the effects of different LOAs under different operating procedures on operating performance. Experimental results indicated that blended decision-making (level 6 LOA) generates the lowest mental workload. Furthermore, the pattern of SA observed in this study is found better SA at intermediate LOA and poorer SA at low level of automation and full automation. Subjective rating results suggest that LOAs distribute the roles of option generation, and selection between human and/or computer servers which significantly impacts automated system performance. This study provides a direction for the HSI designers in nuclear power plants (NPPs). Additionally, based on results obtained by this study, the user interfaces of PCTRAN system and the alarm reset system should be improved to ensure safe operation of NPPs.     

单板层积梁弯曲破坏的试验研究与分析

在万能力学试验机上测试由高频热压方法制造的桦木和椴木单板层积梁的密度、静曲强度(MOR)、弹性模量(MOE)和水平剪切强度等力学性质;讨论LVL(单板层积材)梁受弯曲、水平剪切载荷时的主要破坏形式并得出相关结论。测试结果表明,在该试验条件下,桦木和椴木LVL梁具有较大的密度、MOR和较高的MOE。其主要物理力学性能受树种的影响较大,桦木LVL梁的主要性能均优于椴木LVL梁。当LVL梁受弯曲破坏时,其主要破坏形式为整体断裂破坏、开裂破坏以及混合破坏等3种;受水平剪切应力破坏时,以基材剪切破坏和胶层剪切破坏两种形式为主。     

A comparative study on the autoxidation of dimethyl ether (DME) comparison with diethyl ether (DEE) and diisopropyl ether (DIPE)

The Japanese government is planning to introduce DME as a substituted energy for oil and LNG. Introduction of DME could contribute greatly to both the prevention of global warming and the formation of resource-recycling societies. In these circumstances, a safety assessment of DME is very important when DME is used on a large scale. There is a possibility that prolonged exposure in air induces autoxidation to produce explosive organic peroxides during transportation and storage of DME. Therefore, the reactivity of DME with oxygen and the mechanism of the autoxidation were investigated. Accelerating Rate Calorimetry (ARC) was used to evaluate the thermal stability of DME and DIPE, a known peroxide producers, under adiabatic and various atmospheric conditions. In ARC studies of DME under oxygen, exothermic decompositions were detected although its self-heating rate was low in comparison with DIPE. Oven storage tests were carried out and iodimetry was used to measure the concentration of peroxides produced from DME in comparison with DIPE and DEE. However, no products could be found for DME either by GC/MS or by iodimetry, while some evidence of autoxidation of both DEE and DIPE were obtained from these experiments.     

基于案例推理的大型养路机械故障诊断系统

为实现铁路大型养路机械(简称"大机")故障的智能检索和诊断,使用基于案例推理(CBR)的思路分析和设计用以实现这些目的的系统。阐述案例的表示和构建方法。提出捣固车的故障案例模型构建方法。设计捣固车故障诊断的CBR系统。给出带权值的k-近邻法的案例相似性检索方法。提出大机故障诊断智能决策系统,采用定性和定量检索相结合的方法。故障诊断系统能够进行案例的定性、定量和混合检索。用捣固车的具体故障案例,验证所设计的系统的可行性。诊断系统检索得到的故障类型与依据现场采集的数据判定的故障类型基本一致,能够进行案例调用和修改。     

ZVI与TCE反应参数优化及动力学方程的建立

以批量研究的方法,考察了ZVI纯度、ZVI粒径、ZVI投量、p H值、温度和初始TCE浓度对TCE去除的影响,建立了ZVI去除TCE的动力学方程。最佳参数为:ZVI纯度92%,ZVI粒径30目,ZVI投量30 g,p H值为6.0,温度25℃,初始TCE质量浓度50 mg/L。最佳条件下TCE去除率可达73.6%,反应符合一级动力学方程。