Scleropyrum pentandrum (Dennst.) mabb—oil as a feedstock for biodiesel production—engine performance and emission studies

A feasibility study on utilization of non edible oil of Scleropyrum pentandrum was carried out to see its potential as a new source for biodiesel production. Nonedible oil seeds of Scleropyrum pentandrum have oil content of 55–60%. Transesterification of freshly extracted oil in the presence of anhydrous sodium hydroxide at a concentration 1% (w/v oil) and methanol-oil ratio of 40% (v/v oil) yields 90.8% methyl esters under conventional heating. Month old oil requires sulfuric acid pretreatment (esterification) before transesterification. The transesterified oil has a density 889–893 kg/m³; kinematic viscosity of 4.21–5.7 mm²/s; cetane index 46.03; pour point of ?15°C and gross calorific value of 40.135 MJ/kg and oxidative stability of 2.35 hours. The properties are well within the Indian, European and American standard limits recommended for biodiesel except the oxidation stability, which can be improved by adding antioxidant additives. The engine performance studies of B10 and B20 blends of Scleropyrum pentandrum biodiesel (SP biodiesel) with statistical inference confirmed that it can be used as a fuel in CI engines without any engine modifications. The engine exhaust emission analysis showed that the emission of hydrocarbons can be minimized by at least 15–20%, CO emission by 15%, smoke opacity by 10–12% and moderately lesser CO₂ and NOx emissions.     

Comparison of jatropha and karanja biofuels on their combustion characteristics

Biofuel blends produced from Jatropha (Jatropha curcas) and Karanja (Pongamia pinnata) oil were evaluated for their combustion properties. Two kinds of blends (regular diesel with Jatropha and Karanja oil) were prepared at 20% volume to the diesel and tested as alternative fuels in single cylinder (vertical), water-cooled, direct injection diesel engine at the rated speed of 1500 rpm. The performance of the engine in terms of thermal efficiency at full load for diesel was 30%. For Jatropha and Karanja biodiesel blends, the thermal efficiencies were 29.0% and 28.6%, respectively. The maximum cylinder pressure and ignition delay for biodiesel fuel blends are very close to that of regular diesel. Prolonged combustion was observed for Karanja oil blend in comparison to Jatropha oil blend. The combustion pattern also reveals the slow burning characteristics of vegetable oils and this study indicates that the blended biofuels have combustion characteristics that are similar to regular diesel fuels.     

Production and characterization of biodiesel from Eriobotrya Japonica seed oil: an optimization study

Biodiesel is now-a-days recognized as a real potential alternative to petroleum-derived diesel fuel due to its number of desirable characteristics. However, its higher production cost resulting mainly due to use of costly food-grade vegetable oils as raw materials is the major barrier to its economic viability. Present work is an attempt to explore the potential of Eriobotrya japonica seed oil for the synthesis of biodiesel using alkali-catalyzed transesterification. Optimization of production parameters, namely molar ratio of alcohol to oil, amount of catalyst, reaction time and temperature, was carried out using Taguchi method. Fatty acid composition of both oil and biodiesel was determined using GC and H¹ NMR. Alcohol to oil molar ratio of 6:1, catalyst amount of 1% wt/wt, 2 h reaction time and 50 ^°C reaction temperature were found to be the optimum conditions for obtaining 94.52% biodiesel. Highest % contribution was shown by the ‘amount of catalyst’ (67.32%) followed by molar ratio of alcohol to oil (25.51%). Major fuel properties of E. japonica methyl esters produced under optimum conditions were found within the specified limits of ASTM D6751 for biodiesel, hence it may be considered a prospective substitute of petro-diesel.     

Assessment of biomass and lipid productivity and biodiesel quality of an indigenous microalga Chlorella sorokiniana MIC-G5

Generation of biodiesel from microalgae has been extensively investigated; however, its quality is often not suitable for use as fuel. Our investigation involved the evaluation of biodiesel quality using a native isolate Chlorella sorokiniana MIC-G5, as specified by American Society for Testing and Materials (ASTM), after transesterification of lipids with methanol, in the presence of sodium methoxide. Total quantity of lipids extracted from dry biomass, of approximately 410–450 mg g^?1 was characterized using FTIR and ¹H NMR. After transesterification, the total saturated and unsaturated fatty acid methyl esters (FAMEs) were 43% and 57%, respectively. The major FAMEs present in the biodiesel were methyl palmitate (C16:0), methyl oleate (C18:1), and methyl linoleate (C18:2), and the ¹H NMR spectra matched with criteria prescribed for high-quality biodiesel. The biodiesel exhibited a density of 0.873 g cm^–3, viscosity of 3.418 mm² s^?1, cetane number (CN) of 57.85, high heating value (HHV) of 40.25, iodine value of 71.823 g I₂ 100 g^?1, degree of unsaturation (DU) of 58%, and a cold filter plugging point (CFPP) of –5.22°C. Critical fuel parameters, including oxidation stability, CN, HHV, iodine value, flash point, cloud point, pour point, density, and viscosity were in accordance with the methyl ester composition and structural configuration. Hence, C. sorokiniana can be a promising feedstock for biodiesel generation.     

Homogeneous catalysed biodiesel synthesis from Alexandrian Laurel (Calophyllum inophyllum L.) kernel oil using ortho-phosphoric acid as a pretreatment catalyst

In this study, a non-edible seed oil of Alexandrian Laurel (Calophyllum inophyllum L.) with higher free fatty acid content has been harnessed to produce biodiesel by transesterification process. The 20.2% free fatty acid (FFA) content was first reduced to 12.9% by using TOP degumming process. Ortho-phosphoric acid was used to esterify the refined kernel oil. Transesterification reaction was performed with NaOH as an alkaline catalyst and methanol as an analytical solvent. The effects of methanol to oil molar ratio (MR), catalyst concentration (CC), reaction temperature (TP), reaction time (TM), and stirrer speed (SS) on biodiesel conversion were studied to optimize the transesterification conditions using DOE- approach. The experimental study revealed that 9:1 MR, 0.8 wt.% CC, 60°C TP, 75 min TM and 1000 rpm SS were the optimal process control variables. The study indicated that CC was the most important control parameter in optimal methyl ester production. The optimal treatment combination yielded 97.14% of biodiesel. The profile of biodiesel was determined using gas chromatography-mass spectrometry. ¹H NMR spectrum of Calophyllum inophyllum methyl ester (CIME) has been reported. The properties of the biodiesel have been found within specifications of the ASTM D6751 and EN 14214 standards and hence could be considered as a suitable alternative to diesel fuel for sustainable circulation of carbon.     

Ferric-manganese doped sulphated zirconia nanoparticles catalyst for single-step biodiesel production from waste cooking oil: Characterization and optimization

Biodiesel of waste cooking oil origin is gaining attention as a replacement for current fossil fuels, as its low-priced, recycled feedstock shall prevent food source competition, which is estimated to happen with current biodiesel production processes. As a result, waste cooking oil has been claimed to be a highly potential feedstock for biodiesel production. In the present research work, Fe-Mn doped sulphated zirconia catalyst was synthesized and used in simultaneous esterification and transesterification of waste cooking oil to biodiesel synthesis. The catalyst was prepared through the impregnation method and characterized by using XRD, TPD-NH_3, FT-IR, BET, and TEM. Response surface methodology (RSM) in conjunction with the central composite design (CCD) was applied to statistically evaluate and optimize the biodiesel preparation process. It was found that the synthesis of biodiesel achieved an optimum level of 97.2% waste cooking oil methyl ester’s (WCOME’s) yield at the following reaction conditions: methanol/oil molar ratio: 10:1, catalyst concentration: 3.0 wt %, and reaction temperature: 160 °C. The extremely high WCOME’s yield of 97.2% was proved to be due to high acidity, surface area, and large pore diameter; reactants can easily diffuse into the interior pore of the catalyst and allow them to be in contact with active sites that enhance catalytic activity.     

Biodiesel synthesis and characterization using welted thistle plant (Carduus acanthoides) as source of new non-edible seed oil

In this work we applied base catalyzed transesterification to convert non-edible welted thistle oil (Carduus acanthoides) as new non-edible feedstock into biodiesel (Fatty acid methyl esters). The highest biodiesel yield of 88% was obtained using optimized reaction conditions of 70°C and 5:1 molar ratio (methanol:oil). The synthesized esters were characterize and confirmed by the application of NMR and FT-IR techniques. Gas chromatography and mass spectroscopy identified different fatty acids as palmatic acid (C16:0), oleic acid (C18:1), linoleic acid (18:2), arachidic acid (C20:0), eicosanic acid (C20:1), and erucic acid (C22:1) in the oil of welted thistle. Six corresponding methyl esters reported in welted thistle oil biodiesel includes 9-hexadecenoic acid, hexadecanoic acid, 9-octadecadienoic acid, 11-eicosanoic acid, eicosanoic acid and 13-docosenoicacid. Fuel properties, such as density @40°C Kg/L (0.8470), kinematic viscosity @ 40°C c St (4.37), flash point (95°C), cloud point (+4°C), pour point (?5°C), and sulfur contents (0.0112% wt) of the biodiesel produced were compatible with American Society for Testing and Materials D 6751 specifications.     

Possibility of converting indigenous Salvadora persica L. seed oil into biodiesel in Pakistan

In this research study, biodiesel has been successfully produced from vegetable seed oil of an indigenous plant Salvadora persica L. that meets the international biodiesel standard (ASTM D6751). The biodiesel yield was 1.57 g/5 g (31.4% by weight) and the in-situ transesterification ester content conversion was 97.7%. The produced biodiesel density was 0.894 g/mL, its kinematic viscosity 5.51 mm²/s, HHV 35.26 MJ/kg, flash point 210°C, cetane no. 61, and sulfur content 0.0844%. Thermal analysis of the biodiesel showed that 97% weight loss was achieved at 595°C with total oxidation of the biodiesel. The production energy efficiency was 0.46% with a lab scale setup, assuming the volume fraction ratio (volume of the sample/total volume of the equipment used). The results revealed that single-step in-situ transesterification method is suitable for the production of biodiesel from S. persica seed oil.     

Transesterification of Caesalpinia eriostachys seed oil using heterogeneous and homogeneous basic catalysts

Caesalpinea eriostachys seed oil, as a source of triglycerides with potential application for biodiesel production in Mexico is introduced. Its lipid profile obtained by Gas Chromatography-Mass Spectrometry (GC-MS) revealed saturated and unsaturated glycerol esters as the constituents. Therefore, heterogeneous and homogeneous catalyzed transesterification reactions were assayed employing ZnAl hydrotalcites and KOH, as the catalysts, respectively. The transesterification reactions yielded 59% for Zn/Al(2), 79% for Zn/Al(4), and 90% for KOH, depicting typical behavior, as in biodiesel production data from literature, where Zn-Al hydrotalcites or KOH were assayed. The caloric, density, viscosity values, and fatty acid methyl esters profile from reaction products were concordant to EN 14214, suggesting C. eriostachys as a promising feedstock for biodiesel production.     

A comprehensive review on biodiesel production using Moringa oleifera oil

Biodiesel has emerged as one of the most promising renewable energy to substitute existing petroleum-derived diesel fuel being used in transportation sectors. Among the various feedstocks reported for biodiesel production, Moringa oleifera oil is becoming a promising replacement for conventional diesel fuel. Therefore, this work provides a comprehensive overview of the recent progress in biodiesel production from Moringa oleifera oil. The physicochemical properties, fatty acid composition of oil and methyl esters, oil extraction methods, esterification, and transesterification process, and purification methods employed in the biodiesel production have been discussed.     

Application of treated wastewater and digested sewage sludge to obtain biodiesel from Helianthus annuus L. seeds oil

Waste from wastewater treatment plants (WWTP) for Helianthus annuus L. production may be a viable solution to obtain biodiesel. This study achieved two objectives: assess the agronomical viability of waste (wastewater and sludge) from the Alcázar de San Juan WWTP in central Spain for H. annuus L. production; use H. annuus L. seeds grown in this way to obtain biodiesel. Five study plots, each measuring 6 m × 6 m (36 m²), were set up on the agricultural land near the Alcázar de San Juan WWTP. Five fertilizer treatment types were considered: drinking water, as the control; treated wastewater; 10 t ha^?1 of air-dried sewage sludge; 20 t ha^?1 of air-dried sewage sludge; 0.6 t ha^?1 of commercial inorganic fertilizer. Soil, irrigation water, sewage sludge, crop development and fatty acid composition in achenes oil were monitored. The 20 t ha^–1 dose of sewage sludge proved effective to grow H. annuus L. with similar results to those grown with a commercial fertilizer. However, precautions should be taken when irrigating with wastewater because of high salinity and nutrient deficiency. Sunflower oil was composed mostly of linoleic and oleic acid. The remaining fatty acids were linolenic, estearic, nervonic, palmitoleic, and palmitic.     

Optimization of esterification of fatty acid rubber seed oil for methyl ester synthesis in a plug flow reactor

To date, non-food vegetable oil has been considered as the primary source for biodiesel production. Rubber seed oil has high acid value (34 mgKOH/g) and can be used for biodiesel synthesis. The purpose of this study was to investigate esterification of fatty acid, which derived from rubber seed oil, in a plug flow reactor system at high temperature and low methanol consumption. Response surface methodology was applied for design experiment and optimization of esterification reaction. Temperature, methanol consumption, and sulfuric acid were chosen as variables to examine their influence in a conversion to methyl ester. At 140°C, at 5:1 methanol to fatty acid ratio (by mole), H₂SO₄ 1.5 (%v/w), and space time 20 min, the conversion to methyl ester attained 98.2%. Fourier transform infrared spectroscopy (FTIR) and gas chromatography-Mass spectrometry (GC-MS) were used for analysis and to confirm the formation of methyl ester. Methyl ester was characterized for biodiesel fuel properties in accordance to ASTM standard.     

Prospect of castor oil biodiesel in Bangladesh: Process development and optimization study

In this study, castor oil (CO) has been investigated as a potential source for biodiesel production in Bangladesh. Castor oil has been extracted from the seeds by mechanical press and the Soxhlet extraction method. Maximum oil content of 55.7% has been found by the Soxhlet extraction method. The physicochemical properties such as free fatty acid (FFA) content, kinematic viscosity, saponification value, and density of the oil have been measured by different standard methods. The FFA content and viscosity have been found considerably higher such as 33.5% and 253 mm²/s, respectively. Biodiesel has been prepared using a three-step method comprising of saponification of oil followed by acidification of the soap and esterification of FFA. The overall yield of FFA from CO is found to be around 89.2%. The final step is esterification that produces fatty acid methyl ester (FAME) and a maximum 97.4% conversion of FFA to biodiesel has been observed. The effect of the oil to methanol molar ratio, catalyst concentration, reaction temperature, and time has been investigated for esterification reaction and optimized using the response surface methodology. ¹H NMR of crude castor oil and castor oil methyl ester (COME) was studied and analyzed that confirms the complete conversion of castor oil to biodiesel. Finally, the biodiesel, produced under optimum conditions, was characterized using the various standard method and found comparable with petro-diesel and biodiesel standard.     

Analysis of emission reduction in ethyne–biodiesel-aspirated diesel engine

The present experimental work investigates the use of ethyne gas in biodiesel-fueled diesel engine at different flow rate of 1, 2, and 3 L/min and is compared with diesel operation. This work is aimed to examine the outcome of ethyne gas by dual-fuel operation on emission characteristics of neat biodiesel-fueled stationary diesel engine. The oil derived from mustard seeds are employed as a source for biodiesel. The work was carried out at 2100 rpm (speed) and at an optimal compression ratio of 17. Based on the outcome of this investigation, the maximum reduction in hydrocarbon (25.1%), carbon monoxide (17.24%), and smoke emission (24.8%) was observed for biodiesel–ethyne at 3 L/min than the neat biodiesel. However, NO_x emissions were found to be 15.8% higher for ethyne–biodiesel fueling at 3 L/min owing to increase in combustion gas temperature than neat biodiesel.     

Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Experimental investigation of performance and emission characteristics of diesel engine using Jatropha biodiesel with alumina nanoparticles

Biodiesels have come up as a very strong alternative for diesel fuel. Biodiesels such as Jatropha Oil Methyl Ester (JOME) are comparable in performance with that of the diesel engine. The thermal efficiency of engines fuelled with biodiesels was found lower than conventional diesel fuel but due to the bio-origin, the emission characteristics are much better. However, biodiesel increases the NOx emissions as these are rich in oxygen, hence nanoparticles are used in this experiment to curb the high temperatures and reduce the NOx formation. The experiment on naturally aspired diesel engine was conducted with four prepared test fuels other than neat diesel and neat biodiesel. The 50 and 150 of alumina nanoparticles were added separately to the pure diesel and pure Jatropha biodiesel to form the nano emulsions using ultrasonicator. The properties of nanoemulsion were evaluated using dynamic light scattering technique using zetasizer. The performance and emission characteristics of multi-cylinder diesel engine with these nanoemulsions were compared with that of neat fuels. The results showed that using nanoparticles with diesel and biodiesel can contribute in a more efficient, economical, and eco-friendly engine operation.     

Emission study of a diesel engine fueled with higher alcohol-biodiesel blended fuels

This work examines the effect of butanol (higher alcohol) on the emission pattern of neat neem oil biodiesel (NBD100) fueled diesel engine. Single-cylinder, 4-stroke, research diesel engine was employed to conduct the trial. Blends comprising the mixture of biodiesel and higher alcohol were prepared by employing an ultrasonic agitator. Four test fuels such as neat neem oil biodiesel, diesel, and two blends of higher alcohol/neem oil biodiesel: 10% and 20% (by volume). Experimental result showed that increasing alcohol content to biodiesel brought down the various emissions such as Smoke, NO_x, HC, and CO by 6.8%, 10.4%, 8.6%, and 5.9%, respectively, at all loads. It was also concluded from the trail that a 20% higher alcohol/neem oil biodiesel blends show the promising signs in reducing all the emissions associated with biodiesel fuelled diesel engine.     

Optimization of extraction of oil and biodiesel from Thespesia populnea seed oil by alkali catalyst in India

Thespesia populnea oil was new source of biodiesel. Crude Thespesia populnea oil was used as feedstock for biodiesel production by alkali-catalyzed methanolysis. The reaction in the presence of NaOH as catalyst was carried out to investigate the optimum conditions and to study the effects of variables on the reaction. A methanol to oil ratio of 6:1, sodium methoxide catalyst concentration of 1.5%, mixing intensity of 250 rpm and reaction temperature of 60°C offered the best Thespesia populnea seed oil methyl esters (biodiesel) yield (92.6%). The methyl ester content under these optimum conditions was 92.6% w/w, and all of the measured properties of the Thespesia populnea biodiesel (TPME) met the international standards ASTM D 6751-02. The results reveal that all of the reaction variables in this study had positive effects on the reaction. The results of the present study indicated that TPME could be a potential alternative to petrodiesel     

Evaluating the potential of biodiesel (via recycled cooking oil) use in Singapore,an urban city

Singapore has pledged to attain 7–11% Business-As-Usual carbon emissions reduction by 2020. About 19% of CO₂ contribution stemmed from road transport in 2005. Commercial vehicles, which uses mainly diesel, consumed 695 million litres diesel in 2012. An estimated 115,585 tonnes or 127 million litres cooking oils (derived from seeds/fruits) were consumed in 2010, in which the bulk of used cooking oil is re-incorporated into the food preparation process while only a small amount is being recycled into biodiesel or disposed into the sewerage. Nevertheless, the present research reveals that biodiesel derived from spent cooking oil has potential to be a viable fuel supplement. Surveys were carried out involving three market segments – suppliers, processors and end-users – to identify the barriers and obstacles in mass production of biodiesel. A key enabler of biodiesel as a fuel supplement towards a greener environment lies in government mandate/policies in promoting greater biodiesel usage.     

Transesterification of Pistacia chinensis seed oil using a porous cellulose-based magnetic heterogeneous catalyst

In the present work, a novel cellulose-based porous heterogeneous solid acid catalyst encapsulation of ferriferous oxide (Fe₃O₄) and sulfonated graphene (GO-SO₃H) into cellulose to form composite porous microspheres catalyst (GO-SO₃H/CM@Fe₃O₄)was synthesized and evaluated for biodiesel production from Pistacia chinensis seed oil. The SEM, EDS and FTIR analysis revealed that the catalyst GO-SO₃H/CM@Fe₃O₄ owned stronger active sites and GO-SO₃H dispersed well in porous surface and inside of cellulose support. Under the optimum conditions, microwave-assisted transesterification process was carried out with the best catalyst amount, i.e. 5 wt% GO-SO₃H/CM@Fe₃O₄ (weight ratio of GO-SO₃H/cellulose), and conversion yield reached 94%. The prepared catalyst could be easily separated from reaction solution by extra magnetic field and reclaimed at least five runs.