催化超临界水氧化对氨基苯酚

采用CuO/γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂,在一连续流固定床反应器中进行了超临界水氧化对氨基苯酚实验.实验结果表明,CuO和MnO2催化剂对于对氨基苯酚的氧化降解具有显著的促进作用.对氨基苯酚的去除率随反应温度和压力的升高、停留时间的延长而提高,在24～26 MPa和400～450℃条件下,数秒钟内COD去除率可达到99%以上,催化剂CuO/γ-Al2O3的催化效果优于MnO2/γ-Al2O3.证明了催化超临界水氧化技术的高效性.     

催化超临界水氧化对氨基苯酚

采用CuO／γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂，在一连续流固定床反应器中进行了超临界水氧化对氨基苯酚实验。实验结果表明，CuO和MnO2催化剂对于对氨基苯酚的氧化降解具有显著的促进作用。对氨基苯酚的去除率随反应温度和压力的升高、停留时间的延长而提高，在24～26MPa和400～450℃条件下，数秒钟内COD去除率可达到99％以上，催化剂CuO／γ-Al2O3的催化效果优于MnO2／γ-Al2O3。证明了催化超临界水氧化技术的高效性。     

常温常压催化湿式氧化降解偶氮染料废水的研究

以过渡金属Fe、Mn、Cu和Zn的硝酸盐为活性组分的前驱物,以γ-Al2O3为载体,制备了负载型催化剂Fe2O3/γ-Al2O3、MnO/γ-Al2O3、CuO/γ-Al2O3和ZnO/γ-Al2O3,并分别以H2O2和NaClO为氧化剂,对比了在常温常压条件下催化湿式氧化工艺处理甲基橙模拟废水的效果.结果表明,Fe2...     

CuO/γ-Al_2O_3负载型催化剂催化燃烧处理油烟

采用等体积漫渍法制备不同CuO负载量的CuO/γ-Al2O3负载型催化剂,用X射线衍射仪、扫描电镜对该催化剂负载层活性组分的表面形态、晶相结构和颗粒大小进行表征,考察了该催化荆催化燃烧处理油烟的催化活性(以油烟净化效率表征).结果显示,催化活性随CuO负载量的增加.反应温度的升高而提高,但随烟气流量的增大而降低;在CuO负载量为20%(质量分数)、反应温度为350℃.烟气流量为5 L/min的最佳实验条件下,CuO/γ-Al2O3负载型催化剂的油烟净化效率最高.可达88.6%.该催化剂对油烟的催化燃烧具有较高的催化活性.     

丙烯酸废水超临界水氧化动力学研究

用H2O2作为氧化剂,对丙烯酸生产废水进行超临界水氧化研究.得到了反应速率方程表达式.COD、H2O2和水的反应级数分别为1、0和0,指前因子A为4.97 s-1,反应活化能Ea为20.64 kJ/mol,诱导时间为8 s左右.     

CuO/γ-Al_2O_3非均相过氧化氢催化氧化苯酚的研究

研究CuO/γ-Al_2O_3非均相过氧化氢催化氧化苯酚废水的各种影响因素与动力学规律,结果表明:(1)反应存在最佳pH及过氧化氢加入量(即pH为4~5、过氧化氢加入量为0.097 1mol/L);温度对苯酚转化速率影响很大,温度升高,苯酚转化速率加快。(2)动力学研究得到CuO/γ-Al_2O_3非均相过氧化氢催化氧化体系的模型方程,同时得到该反应的活化能为91.84kJ/mol。     

Mn203/γ-Al2O3在超临界水氧化中催化活性的研究

采用浸渍法制备了Mn2O3/γ-Al2O3催化剂,在超临界水中催化氯化降解1,5-萘二磺酸,探索了催化剂Mn2O3活性组分负载量、催化剂空速和反应溶液pH对Mn2O3/γ-Al2O3催化剂活性的影响.结果表明:Mn2O3/γ-Al2O3的催化活性在一定范围内随Mn2O3活性组分负载量的增加而提高;在一定范围内,Mn2O3/γ-Al2O3空速越小,模拟废水的COD去除率越高;Mn2O3/γ-Al2O3催化活性在反应溶液呈酸性情况下比碱性时高.     

Mn2O3/γ-Al2O3在超临界水氧化中催化活性的研究

采用浸渍法制备了Mn2O3/γ-Al2O3催化剂,在超临界水中催化氧化降解1,5-萘二磺酸,探索了催化剂Mn2O3活性组分负载量、催化剂空速和反应溶液pH对Mn2O3/γ-Al2O3催化剂活性的影响。结果表明：Mn2O3/γ-Al2O3的催化活性在一定范围内随Mn2O3活性组分负载量的增加而提高;在一定范围内,Mn2O3/γ-Al2O3空速越小,模拟废水的COD去除率越高;Mn2O3/γ-Al2O3催化活性在反应溶液呈酸性情况下比碱性时高。     

CuO/γ-Al2O3类Fenton试剂降解丁基黄药

CuO/γ-Al2O3类Fenton试剂是降解丁基黄药的优良试剂。该试剂与传统的Fenton试剂相比,提高了反应的pH值,可在较高pH(4~5)条件下反应,而传统的Fenton试剂的适宜pH值一般在3以下。采用单因素实验和正交实验相结合的方法研究了pH、催化剂投加量、过氧化氢投加量以及反应时间对丁基黄药降解效果的影响,并对催化剂的使用寿命进行了探讨。研究结果表明,反应的最佳条件为:pH为4~5,催化剂投加量为6 g/L,过氧化氢用量为30 mg/L,反应30min。在此反应条件下,丁基黄药的降解率达98%以上;影响丁基黄药降解效果的因素大小顺序为:pH>反应时间>H2O2用量>催化剂投加量,其中pH对CuO/γ-Al2O3类Fenton试剂降解丁基黄药的影响最为显著。     

超临界水氧化活性艳红M-2B染料废水动力学研究

用H2O2作为氧化剂,在595～704 K、18～30 MPa条件下,对活性染料废水进行超临界水氧化反应.实验结果表明,COD去除率随温度、压力、停留时间和氧化剂量的增加而上升,在704 K、28 MPa时,COD去除率可达到98.4%,停留时间小于35 s.COD、H2O2和水的反应级数分别为1、0和0;反应活化能Ea为37.21 kJ/mol;指前因子A为76.69 s-1.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.